GETTING STARTED WITH IN-WALL RELAY SWITCH

Transcription

1 GETTING STARTED WITH IN-WALL RELAY SWITCH This document is the property of Webee L.L.C. The data contained here, in whole or in part, may not be duplicated, used or disclosed outside the recipient for any purpose. This restriction does not limit the recipient's right to use information contained in the data if it is obtained from another source without restriction. 1

2 INDEX Section 1: Mounting your In-Wall Relay Switch Installation...03 In-Wall Relay Switch Connection Diagram...04 Other connection styles Diagrams...05 Section 2: Connecting to Smartee Adding In-Wall Relay Switch to Zigbee Network...06 Binding In-Wall Relay Switch...06 Section 3: Specs Specifications...07 Dimensions...08 Section 4: Security Instructions Security Guidelines...09 Page 02

3 1 1 MOUNTING YOUR IN-WALL RELAY SWITCH Instructions Warnings! To reduce the risk of serious injury or death, turn power OFF before installing this product. (Ce produit doit être à la terre conformément à NEC et exigences locales.) This device must be installed by competent licensed electricians. (Cet appareil doit être installé par un électricien compétent autorisé.) This product must be grounded in accordance to NEC and Local requirements. (Ce produit doit être à la terre conformément à NEC et exigences lo-cales.) Caution! Using this product in any manner other than outlined in this document voids your warranty. Webee is not responsible for any damage incurred as a result of misuse or abuse of this product. (L'utilisation de ce produit de quelque autre manière que décrites dans le présent document annule votre garantie. Webee n'est pas responsable de tout dommage subi à la suite d'un détournement ou d'abus de ce produit.) Installation 1. Confirm that the intended installation location conforms to the following requirements: -Wall box must meet box size requirements specified by the NEC (National Electric Code.) -Installation will be completed according to national and local codes. -The load being controlled by the device does not exceed 1000 W. 2. To avoid SERIOUS INJURY or DEATH, turn OFF the local electrical power feeding the switch location. To disconnect power, turn off the breaker or remove the fuse from the fuse box. Verify that there is no power present using a voltage meter or test light. 3. If you are replacing an existing switch, note which wires are the Ground, Circuit Feed (HOT), Load (Switch Leg), and Neutral, when removing the existing switch. 4. Prepare the wires for connection by stripping off the insulation 5/8 of an inch. 5. Connect the ZigBee HA Relay Switch Wires using the supplied wire nuts. Connect GREEN wire from switch to GROUND Connect BLACK wire from switch to HOT FEED Connect WHITE wire from switch to NEUTRAL Connect RED wire from switch to LOAD Page 03

4 Warnings! If a direct short is created between the RED wire and GROUND or NEUTRAL, the Relay Switch will be damaged and unusable. (Si un court direct est créé entre le fil rouge et SOL ou neutre, le commutateur de relais sera endommagée et inutilisable.) 6. Test all connections. Fold wires and push them neatly into the switch box. Align the Relay Switch in the switch box with the air gap switch oriented at the bottom of the Relay Switch. Using the supplied screws, secure the Relay Switch in the switch box. 7. Verify that the Air Gap switch is fully pushed in. Then turn ON circuit breaker or replace the fuse. 8. If the Relay Switch is installed properly the top LED will blink slowly for 100 seconds signifying that the device is working as a independent local device. 9. You should now be able to control the load by tapping the top button. In-Wall Relay Switch Connection Diagram Connect GREEN wire from switch to GROUND Connect BLACK wire from switch to HOT FEED Connect WHITE wire from switch to NEUTRAL Connect RED wire from switch to LOAD For Keypad Function (Below): Cap RED wire on switch, do not connect. Page 04

5 Other connection styles Wiring for 3-way with load at the end of the circuit. Wiring for 3-way with load in the middle of the circuit. Wiring for 3-way with load at beginning of the circuit. Page 05

6 2 1 CONNECTING TO SMARTEE Adding to Zigbee Network To join the In-Wall Relay Switch to the Smartee, follow these instructions: 1- Click on the Add Device on your App. 2-If the LED on the switch is blinking (scanning for a network to join) and the switch is within range of Smartee ZigBee HA network it will join the network. 3. If the LED is not blinking, press and hold the top button for two seconds. The LED should start blinking and scanning for a network to join. If the Relay Switch has not been captured onto a ZigBee HA network, it s LED will blink slowly upon power up for 100 seconds. Once it s top button is pressed the LED will indicate the Relay Switch Load ON/OFF status. If the load is connected properly the light should toggle states with every button tap. If after following these steps the In-Wall Relay Switch will not join the Smartee Zigbee network, factory default your switch and try again. To factory default your switch do as follows: 1. Disconnect power by pulling out the airgap switch. 2. While pushing the top button, power the switch on by pushing in the airgap switch. 3. After 2 seconds the status LED will turn ON. 4. Once the status LED is ON, release the button. Verify that the switch is wired correctly and powered up. The LED's should light up on the face plate. Button controlling Load: -Tap the button to turn the light ON/OFF. Binding Instructions One *Load Device can have multiple *Keypads bound to it. In order to bind a keypad to a load please follow the following steps: 1. Locate the Load Device and quickly tap the button 6 times, and on the 6th tap push and hold the button down for one second. The LED should start fast blinking. 2. Once the Led is fast blinking, tap the button once. 3. You now have one minute to locate the Keypad you wish to bind to the Load. 4. Once located, quickly tap the button 6 times, and on the 6th tap push and hold the button down for one second. The LED should start fast blinking. 5. Once the LED is fast blinking briefly push and hold the button. To test if this is working, tap the button on the Keypap device and it should toggle the Load. To bind another keypad to the Load, repeat steps 1-5 for the other Keypad with the same Load. To unbind a keypad from the Load, repeat steps 1-5 for the Keypad you wish to unbind. *Load Device = Device that is actually connected to the light via the Red Wire. *Keypad = Device that only has power and neutral and the red wire is capped off. Page 06

7 323 1 IN-WALL RELAY SWITCH SPECS Electrical specifications Description Min Typ Max Unit Rated VAC Input frequency Hz Operating temperature -20º - 40º ºC Storage temperature -20º - 50º ºC Operating Humidity 0-90% RH (nonconndensing) Supported Loads -120 VAC 1/2 HP Motor -120 VAC 1000 W Halogen -120 VAC 1000 W Fluorescent -120 VAC 1000 VA Magnetic Low Voltage Transformer -120 VAC 1000 VA Electronic Low Voltage Transformer VAC Wireless RF Characteristics Description Min Typ Max Unit RF Channels TX Strength dbm Range - >100 ft. (>30m) ft. Protocol Zigbee HA 1.2 Page 07

8 Dimensions Page 08

9 4 1 SAFETY INSTRUCTIONS Safety Guidelines -To be installed and/or used in accordance with appropriate electrical codes and regulations. -If you are unsure about any of these instructions, consult a qualified electrician. -Follow all guidelines carefully, if you have any questions contact us at support@webeelife.com. Warning: Make sure to veriffy that the devices you are connecting are within the electrical range of the In-Wall Relay Switch. Otherwise, it will be damage and will no longer function. Page 09

10 V1.0 REV. February, Webee LLC, All rights reserved. The Webee logo, Smartee and Bees are trademarks or registered trademarks of Webee LLC 10