Blue Point Engineering

Transcription

1 Overview DMX Duo driver board allows 2 Unipolar motors and 1 open collector output driver to be controlled from a DMX512 network. he board provides 2 independent motor drives, 1 external load driver and requires 5 channels of DMX. he base address may be set anywhere between 1 and 508. Connections: DMX: Dual 5 Pin XLR (M/F) and 2 x 3pin terminal connections 1/G = Cable Screen, 2/ 2= Data, 3/ 3 = Data. Power: Standard Board power requirements are 912V DC at 1 Amp per motor coil Decoder 500ma. Maximum 9 amps in total. echnical Version DMX Duo Motor Driver WD1587 Base Address Selection: he base address may be set between 1 and 508 using the DIP switches. Calculate the setting by adding the value of the switches that are set to the ON position. he Base Address is continuously read, No address selected (address = 000, defaults to address 001). Operation: 5 x DMX Channels are required channel 1 and 3 sets the motor speed and direction for motor A & B respectively, 00 = full speed FWD, 255 = Full speed reverse, 128 = Stop, Channels 2 and 4 enable the drive for the motors A and B respectively, a value of > 224 (87% DMX) will active the coil outputs. Channel 5 activates the open collector output driver a value > 224 (87% DMX) switches output 9 ON. Motor Coil connection: he 8 motor coil outputs and driver are rated at 1 Amp Maximum (9 amps 912 VDC and are arranged as open collector outputs for Unipolar type motors only. he Motor coil positive terminals should be connected individually to any of the input terminals and the coil negative terminals to the first 8 input terminals on the board the output driver to Channel 9. (Refer to the diagram below). Indicators: Power LED solid red LED when power applied. DMX Status LED when a valid DMX signal being received solid red LED. No DMX signal, flashing red LED. Blue Point Copyright 2012 Blue Point, All Rights Reserved Phone (303) (MS)

2 echnical DMX Duo Motor Driver Hookup Board Reset Button Network ermination Jumpe (Last board on NetworkON) Optional DMXNetwork Wire Connections (IN / OU) SG 2 3 Power Supply Connection Board Electronics 12 VDC Ch9 Motor 2 RELAY 8 Motor Coil Connections Motor 1 Optional DMXNetwork XLR Cable Connections (IN / OU) DMX Signal LED ON = DMX Signal Present Flashing = No DMX Signal DIP Switches ( Addressing ) DMX Board Address DIP Switches OFF ON X Board Power LED X NOE: DIP Switch Numbers 10 = N/C 9 = = = 64 6 = 32 5 = 16 4 = 8 3 = 4 2 = 2 1 = 1 Blue Point Copyright 2012 Blue Point, All Rights Reserved Phone (303) (MS)

3 echnical DMX Duo Motor Driver Wall Plug Power Supply Amp Power Connection Board Electronics ()V Power Connection and Network V IN Ch9 Motor 2 MAX Load = 9 Amps total per Board Motor 1 NOE Optional DMX Network Connection DMX Network Wire erminal Block DMX IN DMX OU G Black = 2 White = 3 G Black = 2 White = 3 XLR M Connection F XLR Connection o DMX Controller 5Pin (M) XLR Connector 5Pin (F) XLR Connector 5Pin (M) XLR Connector 5 Pin XLR Cable 5 Pin XLR Cable o Next DMX Device Blue Point Copyright 2012 Blue Point, All Rights Reserved Phone (303) (MS)

4 DMX Network Setup 5 Pin Overview Software echnical DMX Duo Motor Driver USB to DMX Interface USB Cable USB POR OR Computer OR USB Cable USB POR Control Software (VSA) Laptop Computer OR DMX Control Console 5Pin (F) XLR Connector 1215 VDC Power Supply DMX XLR Cables DMX XLR Cables 5Pin (M) XLR Connector 5Pin (M) XLR Connector o Next DMX Device 5Pin (F) XLR Connector Blue Point Copyright 2012 Blue Point, All Rights Reserved Phone (303) (MS)

5 DMX Duo Motor Driver Motor Connections Oriental Motor Manufacture Unipolar ype (6 Wire) 1.8 Step 12VDC / 1 Amp Motor 1 Blue Point 12VDC / 1 Amp Blue Wire Red Wire Green Wire Black Wire White Wire Yellow Wire Copyright 2012 Blue Point, All Rights Reserved echnical Power Supply Amp * NOE MAX Load = 9 Amps total per Driver Board Motor 2 Figure 1 Phone (303) (MS) Blue Wire Red Wire Green Wire Unipolar ype (6 Wire) 1.8 Step 12VDC / 1 Amp Black Wire White Wire Yellow Wire

6 DMX Duo Motor Driver Motor Connections * NOE MAX Load = 9 Amps total per Driver Board Oriental Motor Manufacture Unipolar ype (6 Wire) 1.8 Step 5VDC / 1 Amp Motor 1 Blue Point 5VDC / 1 Amp Blue Wire Board Electronics Power Supply Amp Red Wire Green Wire Black Wire Copyright 2012 Blue Point, All Rights Reserved echnical Motor 2 Figure 2 Phone (303) (MS) Motors Power Supply Amp Blue Wire Unipolar ype (6 Wire) 1.8 Step 5VDC / 1 Amp Red Wire Green Wire Black Wire White Wire Yellow Wire White Wire Yellow Wire

7 DMX Duo Motor Driver echnical Optional Board Ch9 Connection Figure 3 Board Electronics Power Supply Motors Power Supply Amp Amp Ch9 A B Optional: Main Power Relay ON / OFF to Motors Motor 1 A B C D Relay Electrical Contacts Normal Open (N.O) Common (COM) Relay Coil (Coil Input) Relay Coil (Coil Input) Motor 2 Motor Coil Power Wires Power Down Motors 1 and 2 Blue Point Copyright 2012 Blue Point, All Rights Reserved Phone (303) (MS)

8 DMX Duo Motor Driver Board Address DMX Motor 1 Motor 1 (DMX Channel 1 Motor 1 Rotation (CW, CCW) (DMX Channel 2 Board Motor 1 Drivers Energized echnical Value CW DMX Channel1 Clockwise Direction (CW) Value = motor1 rotates in the Clockwise Direction Value 128 = Motor 1 movement near Stop Value 127 = motor1 rotates slowest rotation at 128msecs per step in the Clockwise Direction. Value 0 = motor1 rotates fastest rotation speed of 0.5msecs per step in the Clockwise Direction. Note: Some motors may stall or shake at a value near 255, the stepper has exceeded the step rate designed in the motor. Lower the Value to find the Max stepper speed for that type stepper design / manufacture type. Motor Note: Some motors may stall or shake at a value near , the stepper has exceeded the slowest step rate designed in the motor. Change the Value up to find the Min stepper speed for that type stepper design or manufacture type. Value CCW DMX Channel1 Counter ClockWise Direction (CCW) Values = motor1 rotates in the Counter Clockwise Direction Value 128 = motor1 movement near Stop Motor Value 129= motor 1 rotates slowest rotation speed at 128msecs per step in the Counter Clockwise Direction. Value 255 = motor1 rotates fastest rotation speed of 0.5msecs per step in the Counter Clockwise Direction. Note: Some motors may stall or shake at a value near 0, the stepper has exceeded the step rate designed in the motor. Raise the Value 05 to find the Max stepper speed for that type stepper design / manufacture. Note: Some motors may stall or shake at a value near , the stepper has exceeded the slowest step rate designed in the motor. Change the Value down to find the Min stepper speed for that type stepper design or manufacture type. Board Motor Drivers DMX Channel2 Board Motor Drivers Energized ON / OFF Value = Board Motor Driver Activated (ON) Value = Board Motor Driver NO activated (OFF) Blue Point Copyright 2012 Blue Point, All Rights Reserved Phone (303) (MS)

9 echnical DMX Duo Motor Driver Board Address DMX Motor 2 Motor 2 (DMX Channel 3 Motor 2 Rotation (CW, CCW) (DMX Channel 4 Board Motor 2 Drivers Energized DMX Channel3 Clockwise Direction (CW) Value = motor2 rotates in the Clockwise Direction Value 128 = motor2 movement near Stop Value 127 = motor 2 rotates slowest rotation at 128msecs per step in the Clockwise Direction. Value 0 = motor 2 rotates fastest rotation speed of 0.5msecs per step in the Clockwise Direction. Note: Some motors may stall or shake at a value near 255, the stepper has exceeded the step rate designed in the motor. Lower the Value to find the Max stepper speed for that type stepper design / manufacture type. Note: Some motors may stall or shake at a value near , the stepper has exceeded the slowest step rate designed in the motor. Change the Value up to find the Min stepper speed for that type stepper design or manufacture type. Value CCW Value 0127 CW Motor DMX Channel3 Counter ClockWise Direction (CCW) Values = motor 2 rotates in the Counter Clockwise Direction Value128 = motor2 movement near Stop Motor Value 129= motor 2 rotates slowest rotation speed at 128msecs per step in the Counter Clockwise Direction. Value 255 = motor 2 rotates fastest rotation speed of 0.5msecs per step in the Counter Clockwise Direction. Note: Some motors may stall or shake at a value near 0, the stepper has exceeded the step rate designed in the motor. Raise the Value 05 to find the Max stepper speed for that type stepper design / manufacture. Note: Some motors may stall or shake at a value near , the stepper has exceeded the slowest step rate designed in the motor. Change the Value down to find the Min stepper speed for that type stepper design or manufacture type. Board Motor Drivers DMX Channel4 Board Motor Drivers Energized ON / OFF Value = Board Motor Driver Activated (ON) Value = Board Motor Driver NO activated (OFF) Copyright 2012 Blue Point, All Rights Reserved Value Blue Point Phone (303) (MS)

10 echnical DMX Duo Motor Driver Board Address DMX Channel 5 DMX Channel 5 activates the open collector output driver, switches board output 9 ON or OFF. (DMX Channel 5 Energize (ON / OFF) Value = Board Ch9 Output Energized ON (87% DMX) Value = Board Ch9 Output Energized OFF Board Electronics Power Supply Amp LOAD / DEVICE Output Channel 9 On or OFF Optional Relay, Device, Load Connected to output board Ch9 Blue Point Copyright 2012 Blue Point, All Rights Reserved Phone (303) (MS)

11 DMX Duo Motor Driver Board Address DMX Values DIP Switches ( Addressing ) 1632 = 48 ON ON Switch Number 1 Switch Position ( ON or OFF ) OFF ON Switch Value N/C DMX Value 0255 = 0100% 255= ON, 0= OFF Base address selectable between 1 and 503 NOE: Address=000 defaults to Address 001 echnical Power Supply Ch9 Ch4 Ch3 Ch2 Ch1 Setting the base address of Motor Channel Outputs Add the value of the address DIP switches set to the ON position to calculate the base address. Example: DIP switches 5 and 6 set to ON position, the base address is now 48, (1632) this setting is used to determine the starting address output of Channel1, the next Channel would be address 49 for Channel2, and the next 50 for Channel3, 51 for Channel4, 52 for Channel5. Motor 1 DMX Channel1 = Motor 1 Direction (CW / CCW) DMX Value = Motor 1 CW Rotation DMX Value 128 = Motor 1 SOP DMX Value = Motor 1 CCW Rotation DMX Channel2 = Motor 1 Enable Driver output DMX Value = ON output DMX Value 2230 = OFF output Motor 2 DMX Board Channel 9 (Output driver) DMX Channel5 = Activated ON / OFF output driver on board channel9 DMX Value = Open Collector Output Driver OFF DMX Value = Open Collector Output Driver ON DMX Channel3 = Motor 2 Direction (CW / CCW) DMX Value = Motor2 CW Rotation DMX Value 128 = Motor SOP DMX Value = Motor2 CCW Rotation DMX Channel4 = Motor 2 Enable Driver output DMX Value = ON output DMX Value 2230 = OFF output Blue Point Copyright 2012 Blue Point, All Rights Reserved Phone (303) (MS)

12 DMX Duo Motor Driver Notes / Worksheet: DMX Duo Motor BOARD NO: DMX Duo Motor Application: Worksheet W RM = (ON /OFF) Addressing Application Output Ch 3 Ch 2 Ch 1 Value 0 1 OFF ON Addressing 1 = ON 0 = OFF Switch Positions (UP / Down ) X OFF UP ON Down SW1 SW2 SW3 SW4 SW5 SW6 SW7 SW8 SW9 BASE Addressing Copyright 2012 Blue Point, All Rights Reserved DMX Position Blue Point Phone (303) (MS)

13 echnical DMX Duo Motor Driver Motor Blue Point Copyright 2011 Blue Point, All Rights Reserved Phone (303) (MS)

14 echnical DMX Duo Motor Driver Unipolar Motors 12 A B C D E F Brown #1 Wire Brown #2 Wire Yellow Wire Blue Wire Red Wire White Wire Fanning Connector Motor Wires to Connector Blue Point Copyright 2011 Blue Point, All Rights Reserved Phone (303) (MS)