Blue Point Engineering

Size: px
Start display at page:

Download "Blue Point Engineering"

Transcription

1 DMX -hannel Relay oard Overview he DMX Relay board provides up to - programmable Digital Outputs channels when connected to a DMX controlled network. he board ase ddress may be set between and 505. Mechanical Relays Rated: 0 0V. oard Requires 0.5 mp Supply. Setup echnical onnections he board requires a V D supply at 0.5 mps. onnect the relay board to the DMX network using 5-pin XLR connectors. If the DMX Relay board is the last item on the network, place a jumper over the pins marked RM. his will improve the performance of the DMX network, acting as a DMX Network ermination. onnect your loads / devices to the relevant volt-free relay outputs -. ( See relay setup and application example pages for details). Each relay is rated at 0 mps at 0V. Settings - (See Pages on ontrol / ddressing) Set the base address of Relay Output - No. as follows: ( when not in byte mode - see below ) dd the value of the address DIP switches set to the ON position to calculate the base address. Example: DIP switches 6 and 3 set to ON position, the base address is now 8, this setting is used to determine the starting address output of Relay, in DMX Multiple hannel ontrol, the next relay would be address 9 for Relay, and the next 50 for Relay 3, etc. Use this same process for setting the base address in Single hannel ontrol but yte Output Switch 0 is set to ON and a ontrol yte Value Number is added to the DMX output for control of all the 8 Relays. ( see pages on ddressing for more details on yte - inary addressing) ontrol Syntax - (See Pages on ontrol / ddressing) yte Output switch (DIP Switch 0) set to OFF: ( Multiple DMX control channels ) he output on a particular channel will go high (ON) when the DMX transmitted value for that channel exceeds. ( 3 OFF, 0% and ON, 00% ). Each relay - has it's own channel assigned with the base number a relay position number added to determine the address for each relay output. yte Output switch (DIP Switch 0) set to ON: ( Single DMX control channel ) he relay outputs act as a binary representation of the data on the base address channel -example, if the base address is set 5 (0000) then relays through would be ON together. one or more relays can be grouped as a base start address and a single binary value added for each relay output control. DMX LED- ON when a suitable DMX signal is being received or a flashing LED when valid DMX signal stream is being received by the -h DMX relay board. he jumper next to the input power socket should be set to the V position when using mechanical relays and set to the 5 position when using the Solid State Relay oard version. (Default V) DMX -h Relay oard 5-Pin XLR onnectors / lock Power Supply: 0.5 mp 5-/" W x 5-/8" L x -3/8" H opyright 00, ll Rights Reserved ustom Equipment, Unique Electronic Products Version.0-00 WD93-H

2 DMX -hannel Relay oard echnical Hook-up DMX -h Relay oard Optional DMX Network onnection DMX-Network RM - DMX ermination Jumper 3 SG Optional Solid State Relay Setup DMX-Network M XLR- onnectors F OP VIEW RELY - Relay ontacts - ommon N - Normal losed - Normal Open RELY - 3 DMX- OK LED DMX- oard ddress DIP Switches Power LED Power Jack RELY - RELY - - ommon N - Normal losed - Normal Open Mechanical Relays Relay ype V - Mechanical Relay 5- Optional SS Relay DIP Switches ( ddressing ) YE OFF ON opyright 00, ll Rights Reserved ustom Equipment, Unique Electronic Products

3 DMX -hannel Relay oard Power onnection Wall Plug Power Supply 0.5 mp XLR onnection echnical oard Power onnection Power Jack. mm enter Positive Power Jack Jumper- V Relay oard op View XLR / Network onnection Optional erminal lock DMX -Network 3 SG V 5 Optional DMX Network onnection DMX Network onnection IN / OU Mechanical Relays Relay oard Front View SG 3 M M F F XLR onnection M oard Power onnection or RM-OFF RM-ON 5- Pin XLR able 5- Pin XLR able F opyright 00, ll Rights Reserved ustom Equipment, Unique Electronic Products

4 DMX -hannel Relay oard echnical DMX Network Setup - 5 Pin Software Overview US to DMX Interface US POR US able - OR - omputer - OR - ontrol Software (VS) omputer 5-Pin (F) XLR onnector US able 5 Pin (F) to 5 Pin (M) DMX - XLR able US POR onnection s DMX- h Relay oard- onnection s Devices Relays X 8 * DMX- h Relay oard - RM Jumper ON (Last Device On Network) Power Supply Devices Relays X * 5-Pin (M) XLR onnector RM Jumper OFF 5-Pin (F) XLR onnector DMX - XLR able 5 Pin (F) to 5 Pin (M) Power Supply 5-Pin (M) XLR onnector opyright 00, ll Rights Reserved ustom Equipment, Unique Electronic Products

5 DMX -hannel Relay oard DMX Network Setup - 3 Pin Overview US POR Software echnical US to DMX Interface US able US able - OR - omputer - OR - US able omputer US POR ontrol Software (VS) 3-Pin (M) XLR onnector 3-Pin (F) XLR onnector 3 to 3 Pin (M) XLR dapter 3-Pin (F) XLR onnector 3 to 5 Pin XLR dapter able 3 Pin XLR able onnection s Relays..N Relay ON / OFF onnection s losure pplications udio oard, Devices Lights, Motors, FX Relays X DMX- 8 h Relay oard - Relays..N DMX- h Relay oard- Power Supply 5-Pin (M) XLR onnector Devices Relays X 8 Power Supply DMX able 5-Pin (F) XLR onnector RM Jumper ON 5-Pin (M) XLR onnector opyright 00, ll Rights Reserved ustom Equipment, Unique Electronic Products

6 DMX -hannel Relay oard echnical Relay onnection Relay - ON LEDs ( - ) 3 DMX - hannel Relay oard Relay - Relay - 3 Relay - Relay - Relay onnections Relay - ON LEDs ( - ) Mechanical Relays Relay - Relay - 3 Relay - Relay - onnection erminal locks - ommon N - Normal losed - Normal Open - ommon N - Normal losed - Normal Open Relay No. erminal locks Relay onnections opyright 00, ll Rights Reserved ustom Equipment, Unique Electronic Products

7 DMX -hannel Relay oard oard ddress DMX - Values yte Mode- OFF 63 8 ON ON OFF DMX Value % echnical Relay- Relay- (H5) (Value 5-55) (Relay ON) Setting the base address of Relay Outputs when not in byte mode - Switch 0 set to OFF dd the value of the address DIP switches set to the ON position to calculate the base address. Example(H): DIP switches 5 and 6 set to ON position, the base address is now 8, (63) this setting is used to determine the starting address output of Relay, the next relay would be address 9 for Relay, and the next 50 for Relay 3 and 5 for Relay. DIp Switch 5 and 6 ON ase ddress 8 Relay No. ( Relay - ase ddress starting at 8 ) yte Output Switch 0 OFF Relay ON at DMX value 5 RELY - Relay OFF at DMX value 0- Example (H8) (Value 5-55) (Relay ON) ontrol Syntex - (See DMX5 hart hart for Values) yte Output switch (DIP Switch 0) set to OFF: ( Multiple DMX control channels ) he output on a particular channel will go high (ON) when the DMX transmitted value for that channel exceeds. 0 OFF (0%) and 5 ON (00%) Example Switch Number ON Switch Position ( ON or OFF ) OFF Switch Value YE DIP Switches ( ddressing ) OP VIEW 3 DMX Value 5 00% Relay-3 h 50 Relay- h 9 DIp Switch 5 and 6 ON ase ddress Relay No. ( Relay - ase ddress Plus next 3 Relays ) yte Output Switch 0 OFF Relay ON at DMX value 5 RELY - Relay OFF at DMX value 0- opyright 00, ll Rights Reserved ustom Equipment, Unique Electronic Products

8 DMX 5 hart - US Standard echnical hart - US Standard DMX 5 h - Switches h - Switches h - Switches h - Switches h - Switches 3, 3 5, 3 6, 3 7,, 3 8 9, 0,,, 3, 3, 3,, 3, 5,, 3, 6 5 7, 5 8, 5 9,, 5 0 3, 5, 3, 5, 3, 5 3,, 3, 5, 5 5,, 5 6,, 5 7,,, 5 8 3,, 5 9, 3,, 5 30, 3,, 5 3,, 3,, , 6 3, 6 35,, , 6 37, 3, 6 38, 3, 6 39,, 3, 6 0, 6,, 6,, 6 3,,, 6 3,, 6, 5, 3,, 6 6, 3,, 6 7,, 3,, 6 8 5, 6 9, 5, 6 50, 5, 6 5,, 5, 6 5 3, 5, 6 53, 3, 5, 6 5, 3, 5, 6 55,, 3, 5, 6 56, 5, 6 57,, 5, 6 58,, 5, 6 59,,, 5, ,, 5, 6 6, 3,, 5, 6 6, 3,, 5, 6 63,, 3,, 5, , 7 66, 7 67,, , 7 69, 3, 7 70, 3, 7 7,, 3, 7 7, 7 73,, 7 7,, 7 75,,, ,, 7 77, 3,, 7 78, 3,, 7 79, 3,, , 7 8, 5, 7 8, 5, 7 83,, 5, 7 8 3, 5, 7 85, 3, 5, 7 86, 3, 5, 7 87,, 3, 5, 7 88, 5, 7 89,, 5, 7 90,, 5, 7 9,,, 5, 7 9 3,, 5, 7 93, 3,, 5, 7 9, 3,, 5, 7 95,, 3,, 5, , 7 97, 6, 7 98, 6, 7 99,, 6, , 6, 7 0, 3, 6, 7 0, 3, 6, 7 03,, 3, 6, 7 0, 6, 7 05,, 6, 7 06,, 6, 7 07,,, 6, ,, 6, 7 09, 3,, 6, 7 0, 3,, 6, 7,, 3,, 6, 7 5, 6, 7 3, 5, 6, 7, 5, 6, 7 5,, 5, 6, 7 6 3, 5, 6, 7 7, 3, 5, 6, 7 8, 3, 5, 6, 7 9,, 3, 5, 6, 7 0, 5, 6, 7,, 5, 6, 7,, 5, 6, 7 3,,, 5, 6, 7 3,, 5, 6, 7 5, 3,, 5, 6, 7 6, 3,, 5, 6, 7 7,, 3,, 5, 6, , 8 30, 8 3,, 8 3 3, 8 33, 3, 8 3, 3, 8 35,, 3, 8 36, 8 37,, 8 38,, 8 39,,, 8 0 3,, 8, 3,, 8, 3,, 8 3,, 3,, 8 5, 8 5, 5, 8 6, 5, 8 7,, 5, 8 8 3, 5, 8 9, 3, 5, 8 50, 3, 5, 8 5,, 3, 5, 8 5, 5, 8 53,, 5, 8 5,, 5, 8 55,,, 5, ,, 5, 8 57, 3,, 5, 8 58, 3,, 5, 8 59,, 3,, 5, , 8 6, 6, 8 6, 6, 8 63,, 6, 8 6 3, 6, 8 65, 3, 6, 8 66, 3, 6, 8 67,, 3, 6, 8 68, 6, 8 69,, 6, 8 70,, 6, 8 7,,, 6, 8 7 3,, 6, 8 73, 3,, 6, 8 7, 3,, 6, 8 75,, 3,, 6, , 6, 8 77, 5, 6, 8 78, 5, 6, 8 79,, 5, 6, , 5, 6, 8 8, 3, 5, 6, 8 8, 3, 5, 6, 8 83,, 3, 5, 6, 8 8, 5, 6, 8 85,, 5, 6, 8 86,, 5, 6, 8 87,,, 5, 6, ,, 5, 6, 8 89, 3,, 5, 6, 8 90, 3,, 5, 6, 8 9,, 3,, 5, 6, 8 9 7, 8 93, 7, 8, 9, 7, 8, 95,, 7, , 7, 8 97, 3, 7, 8 98, 3, 7, 8 99,, 3, 7, 8 00, 7, 8, 0,, 7, 8 0,, 7, 8 03,,, 7, 8 0 3,, 7, 8 05, 3,, 7, 8 06, 3,, 7, 8 07,, 3,, 7, , 7, 8 09, 5, 7, 8 0, 5, 7, 8,, 5, 7, 8 3, 5, 7, 8 3, 3, 5, 7, 8, 3, 5, 7, 8 5,, 3, 5, 7, 8 6, 5, 7, 8 7,, 5, 7, 8 8,, 5, 7, 8 9,,, 5, 7, 8 0 3,, 5, 7, 8, 3,, 5, 7, 8, 3,, 5, 7, 8 3,, 3,, 5, 7, 8 6, 7, 8 5, 6, 7, 8 6, 6, 7, 8 7,, 6, 7, 8 8 3, 6, 7, 8 9, 3, 6, 7, 8 30, 3, 6, 7, 8 3,, 3, 6, 7, 8 3, 6, 7, 8 33,, 6, 7, 8 3,, 6, 7, 8 35,,, 6, 7, ,, 6, 7, 8 37, 3,, 6, 7, 8 38, 3,, 6, 7, 8 39,, 3,, 6, 7, 8 0 5, 6, 7, 8, 5, 6, 7, 8, 5, 6, 7, 8 3,, 5, 6, 7, 8 3, 5, 6, 7, 8 5, 3, 5, 6, 7, 8 6, 3, 5, 6, 7, 8 7,, 3, 5, 6, 7, 8 8, 5, 6, 7, 8 9,, 5, 6, 7, 8 50,, 5, 6, 7, 8 5,,, 5, 6, 7, 8 5 3,, 5, 6, 7, 8 53, 3,, 5, 6, 7, 8 5, 3,, 5, 6, 7, 8 55,, 3,, 5, 6, 7, , 9 58, 9 59,, , 9 ustom Equipment, Unique Electronic Products

9 h - Switches h - Switches h - Switches h - Switches h - Switches 6, 3, 9 6, 3, 9 63,, 3, 9 6, 9 65,, 9 66,, 9 67,,, ,, 9 69, 3,, 9 70, 3,, 9 7,, 3,, 9 7 5, 9 73, 5, 9 7, 5, 9 75,, 5, , 5, 9 77, 3, 5, 9 78, 3, 5, 9 79,, 3, 5, 9 80, 5, 9 8,, 5, 9 8,, 5, 9 83,,, 5, 9 8 3,, 5, 9 85, 3,, 5, 9 86, 3,, 5, 9 87,, 3,, 5, , 9 89, 6, 9 90, 6, 9 9,, 6, 9 9 3, 6, 9 93, 3, 6, 9 9, 3, 6, 9 95,, 3, 6, 9 96, 6, 9 97,, 6, 9 98,, 6, 9 99,,, 6, ,, 6, 9 30, 3,, 6, 9 30, 3,, 6, 9 303,, 3,, 6, , 6, 9 305, 5, 6, 9 306, 5, 6, 9 307,, 5, 6, , 5, 6, 9 309, 3, 5, 6, 9 30, 3, 5, 6, 9 3,, 3, 5, 6, 9 3, 5, 6, 9 33,, 5, 6, 9 3,, 5, 6, 9 35,,, 5, 6, ,, 5, 6, 9 37, 3,, 5, 6, 9 38, 3,, 5, 6, 9 39,, 3,, 5, 6, , 9 3, 7, 9 3, 7, 9 33,, 7, 9 3 3, 7, 9 35, 3, 7, 9 36, 3, 7, 9 37,, 3, 7, 9 38, 7, 9 39,, 7, 9 330,, 7, 9 33,,, 7, ,, 7, 9 333, 3,, 7, 9 33, 3,, 7, 9 335,, 3,, 7, , 7, 9 337, 5, 7, 9 338, 5, 7, 9 339,, 5, 7, , 5, 7, 9 3, 3, 5, 7, 9 3, 3, 5, 7, 9 33,, 3, 5, 7, 9 3, 5, 7, 9 35,, 5, 7, 9 36,, 5, 7, 9 37,,, 5, 7, ,, 5, 7, 9 39, 3,, 5, 7, 9 350, 3,, 5, 7, 9 35,, 3,, 5, 7, , 7, 9 353, 6, 7, 9 35, 6, 7, 9 355,, 6, 7, , 6, 7, 9 357, 3, 6, 7, 9 358, 3, 6, 7, 9 359,, 3, 6, 7, 9 360, 6, 7, 9 36,, 6, 7, 9 36,, 6, 7, 9 363,,, 6, 7, ,, 6, 7, 9 365, 3,, 6, 7, 9 366, 3,, 6, 7, 9 367,, 3,, 6, 7, , 6, 7, 9 369, 5, 6, 7, 9 370, 5, 6, 7, 9 37,, 5, 6, 7, , 5, 6, 7, 9 373, 3, 5, 6, 7, 9 37, 3, 5, 6, 7, 9 375,, 3, 5, 6, 7, 9 376, 5, 6, 7, 9 377,, 5, 6, 7, 9 378,, 5, 6, 7, 9 379,,, 5, 6, 7, ,, 5, 6, 7, 9 38, 3,, 5, 6, 7, 9 38, 3,, 5, 6, 7, 9 383,, 3,, 5, 6, 7, , 9 385, 8, 9 386, 8, 9 387,, 8, , 8, 9 389, 3, 8, 9 390, 3, 8, 9 39,, 3, 8, 9 39, 8, 9 393,, 8, 9 39,, 8, 9 395,,, 8, ,, 8, 9 397, 3,, 8, 9 398, 3,, 8, 9 399,, 3,, 8, , 8, 9 0, 5, 8, 9 0, 5, 8, 9 03,, 5, 8, 9 0 3, 5, 8, 9 05, 3, 5, 8, 9 06, 3, 5, 8, 9 07,, 3, 5, 8, 9 08, 5, 8, 9 09,, 5, 8, 9 0,, 5, 8, 9,,, 5, 8, 9 3,, 5, 8, 9 3, 3,, 5, 8, 9, 3,, 5, 8, 9 5,, 3,, 5, 8, 9 6 6, 8, 9 7, 6, 8, 9 8, 6, 8, 9 9,, 6, 8, 9 0 3, 6, 8, 9, 3, 6, 8, 9, 3, 6, 8, 9 3,, 3, 6, 8, 9, 6, 8, 9 5,, 6, 8, 9 6,, 6, 8, 9 7,,, 6, 8, 9 8 3,, 6, 8, 9 9, 3,, 6, 8, 9 30, 3,, 6, 8, 9 3,, 3,, 6, 8, 9 3 5, 6, 8, 9 33, 5, 6, 8, 9 3, 5, 6, 8, 9 35,, 5, 6, 8, , 5, 6, 8, 9 37, 3, 5, 6, 8, 9 38, 3, 5, 6, 8, 9 39,, 3, 5, 6, 8, 9 0, 5, 6, 8, 9,, 5, 6, 8, 9,, 5, 6, 8, 9 3,,, 5, 6, 8, 9 3,, 5, 6, 8, 9 5, 3,, 5, 6, 8, 9 6, 3,, 5, 6, 8, 9 7,, 3,, 5, 6, 8, 9 8 7, 8, 9 9, 7, 8, 9 50, 7, 8, 9 5,, 7, 8, 9 5 3, 7, 8, 9 53, 3, 7, 8, 9 5, 3, 7, 8, 9 55,, 3, 7, 8, 9 56, 7, 8, 9 57,, 7, 8, 9 58,, 7, 8, 9 59,,, 7, 8, ,, 7, 8, 9 6, 3,, 7, 8, 9 6, 3,, 7, 8, 9 63,, 3,, 7, 8, 9 6 5, 7, 8, 9 65, 5, 7, 8, 9 66, 5, 7, 8, 9 67,, 5, 7, 8, , 5, 7, 8, 9 69, 3, 5, 7, 8, 9 70, 3, 5, 7, 8, 9 7,, 3, 5, 7, 8, 9 7, 5, 7, 8, 9 73,, 5, 7, 8, 9 7,, 5, 7, 8, 9 75,,, 5, 7, 8, ,, 5, 7, 8, 9 77, 3,, 5, 7, 8, 9 78, 3,, 5, 7, 8, 9 79,, 3,, 5, 7, 8, , 7, 8, 9 8, 6, 7, 8, 9 8, 6, 7, 8, 9 83,, 6, 7, 8, 9 8 3, 6, 7, 8, 9 85, 3, 6, 7, 8, 9 86, 3, 6, 7, 8, 9 87,, 3, 6, 7, 8, 9 88, 6, 7, 8, 9 89,, 6, 7, 8, 9 90,, 6, 7, 8, 9 9,,, 6, 7, 8, 9 9 3,, 6, 7, 8, 9 93, 3,, 6, 7, 8, 9 9, 3,, 6, 7, 8, 9 95,, 3,, 6, 7, 8, , 6, 7, 8, 9, 97, 5, 6, 7, 8, 9 98, 5, 6, 7, 8, 9 99,, 5, 6, 7, 8, , 5, 6, 7, 8, 9 50, 3, 5, 6, 7, 8, 9 50, 3, 5, 6, 7, 8, 9 503,, 3, 5, 6, 7, 8, 9 50, 5, 6, 7, 8, 9 505,, 5, 6, 7, 8, 9 506,, 5, 6, 7, 8, 9 507,,, 5, 6, 7, 8, ,, 5, 6, 7, 8, 9 509, 3,, 5, 6, 7, 8, 9 50, 3,, 5, 6, 7, 8, 9 5,, 3,, 5, 6, 7, 8, Example US Standard DMX 5 DIP Switches ( ddressing ) YE YE ddress Switch Value ddress Switch ON, 3, 6, 8, 9 ON Switch Position OFF ( ON or OFF ) ON Switch Number ON ustom Equipment, Unique Electronic Products

10 DMX -hannel Relay oard oard ddress inary Value yte Mode - ON echnical Example 3 33 ase ddress ON ON ON ON OFF YE DIP Switches ( ddressing ) R R3 R R 3 0 Relay- 3 Relay-3 Relay- Relay- 0 (H33) (Value 5) Relay ON ON 3 ON ON inary Value Setting the base address of Relay Outputs when in byte mode - Switch 0 set to ON dd the value of the address DIP switches set to the ON position to calculate the base address. Example: DIP switches 6 and set to ON position, the base address is now 33. ( Single DMX control channel ) ontrol Syntex - (See inary hart for Values ) he DMX output values now act as a binary representation of the data on the base address channel. Example, if the base address is set to 33 and the value (inary) on DMX channel 33 is 0 (Example: 0000 in binary ) then relays through are OFF. Example R5 R R3 R R RELY - - ON If the base address is set to 33 and the dmx value (inary) on DMX channel 33 is then relays through would be ON inary Value RELY -,3 ON,, OFF If the base address is set to 33 and the dmx value (inary) on DMX channel 33 is 6 (00000 ) then relays,3 would be ON and relays, OFF. RELY -, ON,,3 OFF If the base address is set to 33 and the dmx value (inary) on DMX channel 33 is 85 (0000 ) then relays, would be ON and relays,3 OFF. R8 R7 R6 RELYS - - ll OFF If the base address is set to 33 and the dmx value (inary) on DMX channel 33 is 0 ( ) then relays through 8 would be OFF. opyright 00, ll Rights Reserved ustom Equipment, Unique Electronic Products

11 ustom Equipment, Unique Electronic Products lue Point echnical DMX 8-hannel Relay oard Digit Digit Digit Digit Digit inary Value hart HNNELS 8- or RELYS 8- hannel 8- hannel 8- hannel 8- hannel 8- hannel 8- R8 R7 R6 R5 R R3 R R 0 or 0 or 0 or 0 or 0 or 0 or 0 or 0 or 0OFF ON 8R8 7R7 6R6 5R5 R 3R3 R R Page of

12 DMX 8-hannel Relay oard inary Value hart - ont. Page of inary ction hannels / Ports 0 hannel / Port / Relay OFF hannel / Port / Relay ON HNNELS 3-0 or RELYS - 0OFF - ON echnical R R3 R R 0 or 0 or 0 or 0 or DMX - Relay inary Value hannel / Port Decimal Value inary Value 0 ll hannels / Ports OFF 55 ll hannels / Ports ON 8R8 7R7 6R6 5R5 R 3R3 R R h3 Relay No hannel No Decimal Value inary Value lpha Value OP VIEW h h h0 R- R-3 R- R- h3 h h h0 8 0or 0or 0or 0or D opyright 00, ll Rights Reserved ustom Equipment, Unique Electronic Products

13 DMX -hannel Relay oard echnical pplications Relay onnection Pneumatic Setup ir Supply ir Hose ir Hose 5/ Switching Solenoid ir Valve ( VD) ir Hose Exhaust Ports Vdc - Vdc Vdc Vdc Power Supply Relay No. 8 Relay - Pneumatic ylinder (Double cting) DMX- hannel Relay oard erminal locks Relay onnection Relay- - ommon N - Normal losed ( Not Used) - Normal Open Relay-3 Relay- Relay- LED Lighting FX Unit Sound Playback System Open ontact Relay losure Open ontact Relay losure opyright 00, ll Rights Reserved ustom Equipment, Unique Electronic Products

14 DMX -hannel Relay oard pplication Pneumatic ir ank - Pneumatic ylinders - X X ir Hose V V3 V V N.O. Relay ontact onnections - Relay echnical - Vdc Solenoid ir Valves - Vdc Vdc Vdc Power Supply Power onnections om. Relay ontact onnections - Relay Relay Outputs X Vdc Relay- Relay-3 Relay- Relay- N N - Normal losed ( Not Used ) opyright 00, ll Rights Reserved ustom Equipment, Unique Electronic Products

15 DMX -hannel Relay oard pplications Water Valve Water Valve hannel echnical - Water Source IN - Fountain Heads Fountain Heads Lawn Water Valve ( Volts dc) Water Valve hannel - lack Red Power Supply ( 0 mp ) DMX- hannel Relay oard Power Supply ( 0 mp ) Water (ir) Valve - DMX- 8 hannel Relay oard Red Red - lack onfetti annon ir Valve ir ank opyright 00, ll Rights Reserved ustom Equipment, Unique Electronic Products

16 DMX -hannel Relay oard echnical pplications Relay to LED ar, and Single LED's Red om Relay Outputs R8 R DMX- hannel Relay oard Wall Power Supply ( mp) Red Relays X Red DMX able onnection 5-Pin (M) XLR onnector () () Red () lack (-) LED-ar ( Vdc) LED-Light ars ( Vdc) - (-) () - LED Resistor - OR - LED's Resistors 330 Ohm opyright 00, ll Rights Reserved ustom Equipment, Unique Electronic Products

17 DMX -hannel Relay oard DMX Relay / Switch Logic Motor No. DMX DMX Relay Relay OFF OFF SOP OFF ON ON OFF Motor Logic Motor Relays Motor Relays Relay onnections Motor Status W W ON ON SOP Relay onnections echnical Relay Motor ontrol his design prevents the possibility of both relays from shorting back into the power supply when relays and are switched ON or OFF together at the same time. N N DMX- hannel Relay oard DMX Relay DMX Relay 5- Vdc V -Gnd MOOR POWER RED LK W Rotation N Motor - N om W Rotation om 5- Volt D Permanent Magnet Motor 5-Pin (M) XLR onnector DMX able onnection opyright 00, ll Rights Reserved ustom Equipment, Unique Electronic Products

18 DMX -hannel Relay oard Relay onnection Rotation W D MOOR ontrol- ON / OFF - OR - Rotation W - Vdc Vdc echnical Switch Motor s / to hange Direction Vdc - Vdc Power Supply Volt D Permanent Magnet Motor Motor No. W Rotation W Rotation Motor Logic om om Relay- Relay- N LK RED -Gnd V MOOR POWER (Vdc) Relay Relay Relay ON Motor W Rotation Relay OFF Relay OFF Motor W Rotation Relay ON Relay and ON Relay and OFF Motor ll Stop opyright 00, ll Rights Reserved ustom Equipment, Unique Electronic Products

19 DMX -hannel Relay oard echnical pplication Motor Set-up Rotation W - OR - Rotation W Volt D Motor - 3 Rotation - or Vdc Power Supply Switch - Switch - Rotation hange or DMX Relay oard Rotation Volt D Motor - h- h- h- Rotation Volt D Motor - - Vdc Power Supply opyright 00, ll Rights Reserved ustom Equipment, Unique Electronic Products

20 DMX -hannel Relay oard pplication MP3 / Sound oard Playback udio mp & Speaker echnical OPIONL PLYK Speaker and mplifier (Stereo Output) SD ard MP3 Player oard PLYK - OR - Stereo Sound System MP3 Player oard Power SD ard MP3 Player No MP3 Player No Duo MP3 Player oard h- h- h- MP3 Player oard Power DMX- -h Relay udio MP3 Player No (Stereo Output) udio MP3 Player No Stereo Sound System Speaker and mplifier opyright 00, ll Rights Reserved udio mp & Speaker ustom Equipment, Unique Electronic Products

21 DMX -hannel Relay oard Large Power ontrol * echnical Use caution when working with Voltage. ouching or incorrectly wiring this circuit could cause serious personal injury or damage to equipment. DNGER * Power ransformer ( 5- VD) White 5 - VD - * Wall Plug aution Green (Gnd) White lack DNGER * lack RYDOM 3 Red lack * Plug In Voltage Powered Devices Solid-State Relay Module Relay ontacts h- DMX -h Relay oard opyright 00, ll Rights Reserved ustom Equipment, Unique Electronic Products

22 DMX -hannel Relay oard echnical pplication DMX Hybrid - Set-up Wizard oard ontrol o Servos, Motors, Light FX & Sound Effect Playback OHER Wizard / Puppet ontrollers h- Wizard - 8 ontroller oard o Servomotors and Digital Output hannels Wizard - ontroller oard h-3 h- Wizard oard REM Port onnections (-) o V Devices & Sound Effects Playback Wizard - ontroller oard Wizard REM Port ctivation by DMX- h Relay o Servos, Motors, Light FX & Sound Effect Playback DMX - hannel Relay oard h- Wizard - 3 ontroller oard h- h-3 h- h- h-3 opyright 00, ll Rights Reserved h- Wizard oard REM Port onnections (-) h- o Motors, Light s, LED's Special Effect Devices Wizard - ontroller oard ustom Equipment, Unique Electronic Products

23 DMX -hannel Relay oard Notes / Work Sheet: DMX RELY ORD : DMX RELY ORD pplication: RM (ON /OFF) echnical ddressing Out Put pplication Relay - Relay -3 Relay - Relay - Relay - Relay -3 Relay - Relay - ddressing Relay ON 0 Relay OFF 8 6 R R3 R R inary YE OFF ON SW- SW- SW-3 SW- SW-5 SW-6 SW-7 SW-8 SW-9 SW-0 ddressing Value DMX 0 OFF ON inary opyright 00, ll Rights Reserved ustom Equipment, Unique Electronic Products

Blue Point Engineering

Blue Point Engineering DMX 8-Channel Driver Overview he DMX 8- Channel Driver board is designed to provide 8- consecutive channels of standard or extended range movements for analog type R/C s with output control pulses from

More information

Blue Point Engineering

Blue Point Engineering Sound ctivated Driver oard oard accepts audio input from any nonamplified sound source (Computer, CD player, Digital Sound oard or Microphone) and activates a Solid State Relay ON and OFF in sync with

More information

Blue Point Engineering

Blue Point Engineering Overview DMX Duo driver board allows 2 Unipolar motors and 1 open collector output driver to be controlled from a DMX512 network. he board provides 2 independent motor drives, 1 external load driver and

More information

Blue Point Engineering

Blue Point Engineering Blue Point Engineering SV203 Interface Overview Overview Sensors Light Sensor Motion Sensor Joystick Computer USB PORT Technical Pointing the Way to Solutions! T http://www.bpesolutions.com Animatronic

More information

DMX MP3 VMusic2 Player

DMX MP3 VMusic2 Player DMX MP3 VMusic Player Overview he DMX MP3 VMusic Player provides up to 3- sound tracks of playback with volume control when connected to a DMX network he board Base Address may be set between and 50. echnical

More information

Blue Point Engineering

Blue Point Engineering DMX -Ch Switch Board Overview he DMX video switcher board will switch up to composite video input signals to a single video output channel under user control. he board requires a single DMX channel and

More information

Blue Point Engineering

Blue Point Engineering lue Point 8-Channel RPU oard www.pesolutions.com Overview 8-Ch Remote Playback oard for RPU Interface his unique microprocessor based control board was designed to allow playback selection for 1-8 channel

More information

Second Encoder Option Card for PowerFlex 700S Drives with Phase II Control

Second Encoder Option Card for PowerFlex 700S Drives with Phase II Control Installation Instructions Second Encoder Option ard for PowerFlex 700S Drives with Phase II ontrol!!! TTENTION: To avoid an electric shock hazard, verify that the voltage on the bus capacitors has discharged

More information

Blue Point Engineering

Blue Point Engineering Blue Point Engineering Board - Pro Module (E) Instruction Pointing the Way to Solutions! Controller I Version 2.1 The Board Pro E Module provides the following features: Up to 4 minutes recording time

More information

Digital Lighting Systems, Inc.

Digital Lighting Systems, Inc. igital Lighting Systems, Inc. -MPW our hannel MX5 TRI / SR Trigger oard MX5 compatible -MPW USR'S MNUL -UM 0- Low Voltage Wiring Methods igure 4 M Network Ports onnections. uttom view 8 to V / 00 M rom

More information

SPX Supervised Reader Extender. Wiring Diagram and Operators Manual MAN-FA-SPX-1200 V1.03

SPX Supervised Reader Extender. Wiring Diagram and Operators Manual MAN-FA-SPX-1200 V1.03 SPX-1200 Supervised eader Extender Wiring Diagram and Operators Manual MAN-FA-SPX-1200 V1.03 2005 ypress omputer Systems,Inc. www.cypressworld.com Page 1 Table of ontents Quick eference guides Page 3,4

More information

Blue Point Engineering

Blue Point Engineering DMX Controllers Controllers C DMX - 8Ch Relay Modules ( BPE # DMX-3001 )- Mechanical ( BPE # DMX-3003) - SS Relay 8 Solid State relay outputs Solid State Relays AC/DC DMX - 8Ch SS Relay Modules ( BPE #

More information

Blue Point Engineering

Blue Point Engineering echnical Overview his small size, 75 watt, 2 channel output audio amplifier can be used in animatronics, haunted house applications, museum, safety info deliver or many entertainment engineering applications.

More information

Chapter. F0-04AD-2, 4-Channel Analog Voltage Input. In This Chapter...

Chapter. F0-04AD-2, 4-Channel Analog Voltage Input. In This Chapter... F0-0-, -hannel nalog Voltage Input hapter In This hapter... Module Specifications... Setting the Module Jumpers... onnecting and isconnecting the Field Wiring... Wiring iagram... Module Operation... Special

More information

4 Channel 4-20mA/0-10V Industrial Media Converter

4 Channel 4-20mA/0-10V Industrial Media Converter USER GUIDE RLH Industries, Inc. The leader in rugged fiber optic technology. U5 08A00 hannel 0mA/00V Industrial Media onverter SYSTEM INSTALLATION INFORMATION Description This Fiber Optic Media converter

More information

S ite Selection and Mounting S ite Location Planning The Aurora Universal Residential is connected to the Internet using CAT- or CAT- c ompatible cabl

S ite Selection and Mounting S ite Location Planning The Aurora Universal Residential is connected to the Internet using CAT- or CAT- c ompatible cabl A urora Universal Residential Installation Guide This installation document covers details for installing the Aurora Universal Residential hardware to work directly with an inverter. Through Aurora Universal

More information

DMX512-4 Channel PWM Driver Board #805

DMX512-4 Channel PWM Driver Board #805 DMX512-4 Channel PWM Driver Board #805 Overview The 4-channel PWM driver board provides four open drain (collector) type outputs that can be directly controlled from a DMX512 network. The four channels

More information

Stepnet. Module. Provides Mounting & Connections for Stepnet Module CANopen Stepping Motor Driver DEVELOPMENT KIT

Stepnet. Module. Provides Mounting & Connections for Stepnet Module CANopen Stepping Motor Driver DEVELOPMENT KIT Provides Mounting & onnections for Nopen Stepping Driver FETURES Develop & Debug projects then transfer design to OEM pc board. MODEL DRIVER Ic Ip VD TDK-0-0 STM-0-0 DESRIPTION The Development Kit is a

More information

Click-A-Tune. User Manual

Click-A-Tune. User Manual Contents Configuring the...2 Transferring data to the...2 with switch configuration...3 with switch matrix up to 3 switches...4 Changing the playback volume...5 Connections... Power requirements (Vin)...

More information

CONTROL PROTOCOL Motorized Projection Screens

CONTROL PROTOCOL Motorized Projection Screens CONTROL PROTOCOL Motorized Projection Screens Table of Contents Overview... 3 Control Wiring Diagram... 3 IR Control... 4 Remote Button IR Hex Commands... 4 12 Volt DC Trigger... 5 Contact Closure and

More information

PRO PRO ST-2000 ST-2100 P CAT5 Whole-House Intercom System

PRO PRO ST-2000 ST-2100 P CAT5 Whole-House Intercom System 1 hannel Vision Technology will repair or replace any defect in material or workmanship which occurs during normal use of this product with new or rebuilt parts, free of charge in the US, for one year

More information

Wizard- 3 Controller to Optional Track 1-4 Playback Set-up

Wizard- 3 Controller to Optional Track 1-4 Playback Set-up Wizard- 3 Controller to Optional Track 1-4 Playback Set-up 09/24/09 REM-CH Header PINS Not Used 1-Pin G-Pin Track 1-4 ming Selection Switches Momentary Push Button () () () () Toggle Switch Toggle Switch

More information

genesis Master Unit GEN-001 genesis Master Unit - Technical Manual TECHNICAL MANUAL Australian Owned, Designed and Manufactured

genesis Master Unit GEN-001 genesis Master Unit - Technical Manual TECHNICAL MANUAL Australian Owned, Designed and Manufactured Australian Owned, Designed and Manufactured Master Unit GEN-001 Genesis Electronics Australia Pty Ltd www.genesiselectronics.com.au Distributed by: Genesis reserves the right to change or modify products

More information

ACTION ELECTRONICS. P110 Operating Instructions

ACTION ELECTRONICS. P110 Operating Instructions ACTION ELECTRONICS P110 Operating Instructions 1. Quick Start Guide Your P110 comes fully programmed & ready to go, there is no setup required although for more detailed setup refer to section 2. Installation

More information

OPERATING MANUAL Manual Version 1.4 (Sep 11, 2017) Tel: or

OPERATING MANUAL Manual Version 1.4 (Sep 11, 2017) Tel: or BooTunes Amped OPERATING MANUAL Manual Version 1.4 (Sep 11, 2017) Tel: 1-877-815-5744 or 1-905-803-9274 www.frightideas.com Getting Familiar with your BooTunes Amped BooTunes Amped FI-418 Operating Manual

More information

ISS- 02 SPINDLE SPEED SPECS:

ISS- 02 SPINDLE SPEED SPECS: ISS-0 ISOLATED SPINDLE SPEED MODULE For use with UBOB based products (MP000) The ISS-0 comes with a D support disc. If you are setting up an MP000 and Spindle Speed for the first time you MUST first install

More information

WARNING - WARNING - WARNING - WARNING - WARNING - WARNING - WARNING - WARNING - WARNING - WARNING - WARNING - WARNING - WARNING

WARNING - WARNING - WARNING - WARNING - WARNING - WARNING - WARNING - WARNING - WARNING - WARNING - WARNING - WARNING - WARNING WRNIN - WRNIN - WRNIN - WRNIN - WRNIN - WRNIN - WRNIN - WRNIN - WRNIN - WRNIN - WRNIN - WRNIN - WRNIN The project described on these pages uses POTENTILLY FTL HIH VOLTES. If you are in any way unfamiliar

More information

DCS Digital Control Expansion System

DCS Digital Control Expansion System S Digital ontrol Expansion System 4 position Phoenix type connector for power supply. 2 LED s on the front indicating power. Internal backplane with system bus. Internal self-resetting fuses. General Description:

More information

Evaluates: MAXQ617 Intended for IR Applications. MAXQ617 Evaluation Kit. Features and Benefits. General Description.

Evaluates: MAXQ617 Intended for IR Applications. MAXQ617 Evaluation Kit. Features and Benefits. General Description. MXQ67 Evaluation Kit General Description This evaluation kit provides a platform for evaluating the capabilities of the MXQ67, 6-bit, RIS microcontrollers targeted for infrared applications. The motherboard

More information

Blue Point Engineering

Blue Point Engineering Wizard - 1 ontroller (BPE # WA-0001 ) Wizard - 2 ontroller (BPE # WA-0020 ) Wizard - 3 ontroller (BPE # WA-0030 ) Wizard - 4 ontroller (BPE # WA-0040 ) Wizard - 5 & Sound ontroller (BPE # WA-0050 ) Wizard

More information

Network Design and Setup

Network Design and Setup 2 3 2 hoosing the onfiguration nalyze your pplication There are almost as many ways to build your network as there are grains of sand at the beach. The first step in determining the configuration is to

More information

PCinterface QL-PCi mk4

PCinterface QL-PCi mk4 Pinterface QL-Pi mk channel ue Light control from your Touch Screen or Show ontrol P ontrol up to ue Light Master Stations ontrol Outstations across 9 channels Simple byte SII commands Return Status Monitoring

More information

Sigma DeviceNet Tool Change Systems USER S GUIDE Rev 05

Sigma DeviceNet Tool Change Systems USER S GUIDE Rev 05 Sigma DeviceNet Tool Change Systems USER S GUIDE 94018 Rev 05 648 Saratoga Road Glenville, NY 12302 USA Phone: 518 384 1000 Fax 518 384 1200 www.arobotics.com 1. PRECAUTIONS 1 Sigma DNET Module 1 2.0 DNET

More information

KDS Channel DMX Controlled Servo Kit

KDS Channel DMX Controlled Servo Kit KDS00801 8-Channel DMX Controlled Servo Kit This is a DMX512-A controlled servo kit using ANSI approved RJ-45 connectors for DMX networks. Power requirements are 8-20 VDC @ 50 ma. The board features an

More information

LED PAR56 Order Code: P56-151

LED PAR56 Order Code: P56-151 LED PAR56 Order Code: P56-151 www.cobrainternational.com User Manual COBRA P56-151 Dear Customer, Thank you for purchasing the COBRA P56-151. Cobra is one of the leading manufacturers of professional equipment

More information

CHAPTER Wi r i n g NOTICE:

CHAPTER Wi r i n g NOTICE: CHAPTER Wiring NOTICE: Information in this manual may change without notice. Midway Games West Inc. reserves the right to make improvements in equipment function, design, or components as progress in engineering

More information

MDSM is the commercial industry s

MDSM is the commercial industry s MSM is the commercial industry s smallest -type connector for shielded I/O wire-to-board applications. Requiring less than 1/3 the area of a traditional Subminiature connector, MSM is designed for situations

More information

If I wanted to connect an LED and little light bulb and have them switch on and off with one switch, my schematic would look like the one below.

If I wanted to connect an LED and little light bulb and have them switch on and off with one switch, my schematic would look like the one below. Relays Relays are great tools for turning on and off entire circuits, either with a small control switch, or with a microcontroller like the Arduino. To understand how relays are useful and how to control

More information

ELK. Computer Sound Card Interface ELK-129. Features. Specifications / Requirements

ELK. Computer Sound Card Interface ELK-129. Features. Specifications / Requirements Computer Sound Card Interface ELK-129 The ELK-129 Computer Sound Card Interface allows a computer s speaker output to be used as one of the tools for programming the ELK Recordable Modules, such as the

More information

BIPOLAR PROM ADAPTER READ THIS SHEET FIRST!

BIPOLAR PROM ADAPTER READ THIS SHEET FIRST! BIPOLAR PROM ADAPTER READ THIS SHEET FIRST! The BIPOLAR PROM ADAPTER (#ABIP) must be used with caution. The addendum which accompanies the adapter describes the precautions which must be followed for the

More information

Designer Systems. 4 Channel Stepper Driver Shield. Technical Data. to Arduino or Raspberry-PI

Designer Systems. 4 Channel Stepper Driver Shield. Technical Data. to Arduino or Raspberry-PI 4 Channel Stepper Driver Shield for rduino and Raspberry-PI Designer Systems PRODUCT DESIGN ND MNUFCTURING.co.uk Technical Data Features rduino TM UNO Shield standard form factor for simple integration

More information

VS510SZ Hot Sheet. System Model # VSP-VS510SZ-DCAH Software Version # 36 EPN # Base PCBA - PN PCB VS500Z - PN Rev C or D

VS510SZ Hot Sheet. System Model # VSP-VS510SZ-DCAH Software Version # 36 EPN # Base PCBA - PN PCB VS500Z - PN Rev C or D VS510SZ Hot Sheet System Model # VSP-VS510SZ-DAH Software Version # 36 EPN # 1801 Base PBA - PN 54372-01 PB VS500Z - PN 22972 Rev or D Base Panels Serial Standard PN 53189 Template used: 40600_E.pdf 07/05/2006.pdf

More information

Products no longer available

Products no longer available echnical data sheet NV4-MF(-) Modulating linear actuator for -way and 3-way globe valves Actuating force 1000 N Nominal voltage AC/DC 4 V Modulating control DC 0... 10 V Position osition feedback feedbac

More information

Electrical data Nominal voltage AC/DC 24 V Nominal voltage frequency. Draft

Electrical data Nominal voltage AC/DC 24 V Nominal voltage frequency. Draft echnical data sheet LH24A-MF2-P Parmeterisable linear actuator for adjusting dampers and slide valves in technical building installations Air damper size up to approx. m² Actuating force 5 N Nominal voltage

More information

Key Features. Instant Reboot The CV-100/P2000 Series supports 0.2 second instant reboot for critical factory application.

Key Features. Instant Reboot The CV-100/P2000 Series supports 0.2 second instant reboot for critical factory application. Industrial Panel P V-112/P2000 12.1" 6th Gen. Intel ore Processor U Series Fanless Touch Panel P with FM & DS Technology Key Features 12.1" SVG TFT-LD with Resistive 5-wire / Projected apacitivetouch Onboard

More information

DMX-RGB-5A. Overview DMX DECODER

DMX-RGB-5A. Overview DMX DECODER Page 1 of RG Overview SPECIFICTIONS CHNNELS 3 INPUT SIGNL 12 1990 digital signal SIGNL 0 100% PWM dimming signal, can drive max per channel VOLTGE POWER 24V, 30W TEMPERTURE RTING 0 C 0 C CSE DIMENSIONS

More information

4.2 Expansion Modules MAC00-B1/B2/B4

4.2 Expansion Modules MAC00-B1/B2/B4 4. Expansion Modules MC00//4 MC00 With DSU connectors MC00 With cable glands MC004 With M connectors 4.. Expansion modules MC00, and 4 overall description The expansion modules MC00, and 4 can be mounted

More information

8/16 Passive Switcher

8/16 Passive Switcher roadcast evices, Inc. / Passive Switcher TEHNIL REFERENE MNUL roadcast evices, Inc. www.broadcast-devices.com Tel. () -0 Fax. () - REV: / Table of ontents I. Introduction II. Specifications III. Installation

More information

GV-I/O Box 4 Ports V1.2

GV-I/O Box 4 Ports V1.2 GV-I/O Box 4 Ports V1.2 small but a capable device, the GV-I/O Box 4 Ports V1.2 provides 4 inputs and 4 relay outputs. It supports both and output voltages, and provides a USB port for P connection. Key

More information

SAS 846 TQ BACKPLANE

SAS 846 TQ BACKPLANE #9 FN# JP6 JP54 J48 BUZZER RESET J47 J46 J42 J4 J40 JP8 JP4 JP0 64 7 2 I2#6 SIDEBND#6 JP7 +2V GND GND 49 20 2 6 7 JP22:TRL_ID#5 JP25:TRL_ID#6 22 2 8 9 JP6 JP2 JP5 JP08 SIDEBND#5 JP2:I2RST#5 JP24:I2RST#6

More information

VS501Z-4K Hot Sheet. System Model # VSP-VS501Z-CCAJ Software Version # 35 EPN # Base PCBA - PN PCB VS500Z - PN Rev C or D

VS501Z-4K Hot Sheet. System Model # VSP-VS501Z-CCAJ Software Version # 35 EPN # Base PCBA - PN PCB VS500Z - PN Rev C or D VS501Z-4K Hot Sheet System Model # VSP-VS501Z-AJ Software Version # 35 EPN # 1801 Base PBA - PN 54357-01 PB VS500Z - PN 22972 Rev or D Base Panels Mini PN 52144 Lite Digital PN 54094 Lite Duplex PN 51676

More information

Example 1: Using Modbus Poll to MB-GATEWAY with DL06 Slave... A-2. Step 3: Connect to the MB-GATEWAY using the Modbus Poll simulator software...

Example 1: Using Modbus Poll to MB-GATEWAY with DL06 Slave... A-2. Step 3: Connect to the MB-GATEWAY using the Modbus Poll simulator software... pplication Examples ppendix In this ppendix... Example 1: Using Modbus Poll to M-GTEWY with L0 Slave... - Items needed for this example:... - Step 1: onnect the M-GTEWY serial port to the L0 secondary

More information

MK5 5-Axis Controller

MK5 5-Axis Controller MK5 5-Axis Controller Technical Reference Manual PCB Rev 1.0 2010 SOC Robotics, Inc. 1 Manual Rev 0.91 Introduction The MK5 is a 5-Axis breakout board that accepts the MM120, MM130, MM133 or MM220 stepper

More information

genesis genesis Expander Unit - Technical Manual TECHNICAL MANUAL Australian Owned, Designed and Manufactured Expander Unit GEN-010

genesis genesis Expander Unit - Technical Manual TECHNICAL MANUAL Australian Owned, Designed and Manufactured Expander Unit GEN-010 Australian Owned, Designed and Manufactured Expander Unit GEN-010 Genesis Electronics Australia Pty Ltd www.genesiselectronics.com.au Distributed by: Genesis reserves the right to change or modify products

More information

Routout CNC 3 Axis Plug & Play Controller Data Sheet Version 1.1

Routout CNC 3 Axis Plug & Play Controller Data Sheet Version 1.1 Routout CNC 3 Axis Plug & Play Controller Data Sheet Version 1.1 The Routout CNC 3 Axis stepper motor drive box has many uses including for CNC retrofitting / robot control or driving you own CNC machine.

More information

installation quick guide integrated access control & environmental monitoring

installation quick guide integrated access control & environmental monitoring installation quick guide integrated access control & environmental monitoring Introduction This Installation Quick Guide is suitable for standard wallmountable AX300 controllers. Illustrative technical

More information

9 th Generation Plasma Display. Technical Information

9 th Generation Plasma Display. Technical Information 9 th Generation Plasma Display Technical Information 1 The technicians have express their needs and we listened. This presentation has been developed especially for the technicians involved in the repair

More information

Quad-Relay Delay Switch (QRDS) User Manual (v1.0)

Quad-Relay Delay Switch (QRDS) User Manual (v1.0) Quad-Relay Delay Switch (QRDS) User Manual (v1.0) Introduction: The QRDS-1000 Quad-Relay Delay Switch provides general purpose control for up to four independent devices. It also offers optional activation

More information

Seven Channel Remote Control

Seven Channel Remote Control Seven Channel Remote Control Page 1 Versa7 Kit Contents The Versa7 is designed to remotely control up to seven devices, or functions. All seven functions can be controlled with the supplied four button

More information

Data Sheet: Model 5200 Controller

Data Sheet: Model 5200 Controller Description Programmable automation controller with integrated 0/00 -Bit thernet communications. wo asynchronous communications ports (wo RS-232 or ne RS-232 + ne RS-485) Up to 24 odular I/ bays n-board

More information

The Kore Effects Series Prop Controllers

The Kore Effects Series Prop Controllers The Kore Effects Series Prop Controllers Operation Manual Updated 5/18/15 Revision 1.0 Page 1 13 Table of Contents Overview ---------------------------------------------------------------------------------

More information

RDC-7.1. Quick Guide. Enjoying Home Theater. For full details on using the RDC-7.1, refer to the main instruction manual.

RDC-7.1. Quick Guide. Enjoying Home Theater. For full details on using the RDC-7.1, refer to the main instruction manual. D-. For full details on using the D-., refer to the main instruction manual. njoying Home Theater Quick Guide enter speaker omplements the sound effects from front left and right speakers to enrich and

More information

Table of Contents Interface Module Systems

Table of Contents Interface Module Systems UHNN Terminal locks Note: ll part numbers are RoHS ompliant. Table of ontents Interface Module Systems Overview (atalog Numbering ode) 196 Interface Modules 197-204 DIN 41612 onnector 198 Telco onnector

More information

DVI-HDCP-TPS-TX220. TPS (HDBaseT TM ) extender for DVI with local monitor out. Highlight features

DVI-HDCP-TPS-TX220. TPS (HDBaseT TM ) extender for DVI with local monitor out. Highlight features TPS (HDaseT TM ) extender for DVI with local monitor out The is the high end part of Lightware s TPS (HDaseT Transmitter ) product family. The device is an all-round video, and control transmitter over

More information

FX-2 Control Board ASY-360-XXX Setup and Configuration Guide

FX-2 Control Board ASY-360-XXX Setup and Configuration Guide FX-2 Control Board ASY-360-XXX Setup and Configuration Guide Micro Air Corporation Phone (609) 259-2636 124 Route 526. WWW.Microair.net Allentown NJ 08501 Fax (609) 259-6601 Table of Contents Introduction...

More information

SO-3WON- - SO-3WOI- - 3-Button Window Treatment Wallstation with Occupant Sensor Connection

SO-3WON- - SO-3WOI- - 3-Button Window Treatment Wallstation with Occupant Sensor Connection LUTON SO-WON- - SO-WOI- - -utton Window Treatment Wallstation with Occupant Sensor onnection SO-WON-WH-E0 (Non-insert version) olor and Engraving odes LEDs Engraving so-wo 7.8.05 Description Used to control

More information

4 Channel DMX Driver Instruction Manual

4 Channel DMX Driver Instruction Manual LEDstuff.co.nz 4 Channel DMX Driver Instruction Manual Quality LED Lighting Products The LEDstuff 4 Channel DMX Driver is a flexible module that is an ideal addition to an existing home automation or lighting

More information

S200 Base Unit. Quick Start Guide. Part # M-S Initial Release Revision A: 8/2008 S200 Revamp as Base Unit only guide

S200 Base Unit. Quick Start Guide. Part # M-S Initial Release Revision A: 8/2008 S200 Revamp as Base Unit only guide S00 Base Unit Part # M-S-0-07 Initial Release Revision A: 8/008 S00 Revamp as Base Unit only guide Quick Start Guide NT: This is a Quick Start Guide. For a full Installation Manual visit our website http://www.danahermotion.com/documents

More information

Syncrolite ArenaColor User Guide

Syncrolite ArenaColor User Guide Syncrolite ArenaColor User Guide Syncrolite, LP 2025 Royal Lane, Suite 370 Dallas, TX 75220 214.350.7696 214.350.8051 fax www.syncrolite.com 1 Tapping the ballast WARNING: Power must be turned off before

More information

Relays SAFETY RELAYS SERIES. High Integrity Safety Relays. Suitable for SIL 3 applications according to IEC and IEC D5000 / D1000 SERIES

Relays SAFETY RELAYS SERIES. High Integrity Safety Relays. Suitable for SIL 3 applications according to IEC and IEC D5000 / D1000 SERIES D5000 / D1000 SERIES SFETY RELYS SERIES High Integrity Safety Relays Suitable for applications according to IEC 61508 and IEC 61511 Relays technology for safety DTS0262-1 27 SFETY RELY - FETURES SFETY

More information

AV24-MFT AV24-MFT2 AV24-MFT2-C105. Power consumption In operation For wire sizing N 1700 N Control Control signal Y Operating range

AV24-MFT AV24-MFT2 AV24-MFT2-C105. Power consumption In operation For wire sizing N 1700 N Control Control signal Y Operating range echnical data sheet AV4-MF()(-C105) Multi-functional linear actuators for -way and 3-way globe valves Actuating force 500 N Nominal voltage AC/DC 4 V Control: modulating DC 0 10 V Position feedback DC

More information

Connecting a Cisco Output Module

Connecting a Cisco Output Module CHAPTER 5 Overview The optional Cisco Output Module (Figure 5-1) is attached to a Cisco Physical Access Gateway or Cisco Reader Module to provide additional connections for up to 8 outputs, each of which

More information

Cobra Dimmer Master DMX Controller User Manual

Cobra Dimmer Master DMX Controller User Manual Cobra Dimmer Master DMX Controller User Manual User Manual Dimmer Master Dear Customer, Thank you for purchasing the Dimmer Master DMX controller. With decades of experience in design and production, we

More information

Professional Development Board (#28138)

Professional Development Board (#28138) 599 Menlo Drive, Suite 100 Rocklin, California 95765, USA Office: (916) 624-8333 Fax: (916) 624-8003 General: info@parallax.com Technical: support@parallax.com Web Site: www.parallax.com Educational: www.stampsinclass.com

More information

The purpose of this operation manual is to provide information to ensure proper installation of this product.

The purpose of this operation manual is to provide information to ensure proper installation of this product. I..E. Integrated abin Entertainment System Installation Manual vionics Innovations 50 Montecito Road Ramona, 9065 Phone (760) 788-60 Fax (760) 789-7098 P/N 800-00, Revision March 0, 006 Intentionally Left

More information

For Powerful Digital Marketing and Total Multimedia Solution DV & DV-66104T. User s Guide version 2

For Powerful Digital Marketing and Total Multimedia Solution DV & DV-66104T. User s Guide version 2 For Powerful Digital Marketing and Total Multimedia Solution DV-66104 & DV-66104T User s Guide version 2 Acknowledgements The MedeaWiz logo and DV-66104 are trademarks of MedeaWiz Corporation. All other

More information

USER S MANUAL. C32- DUAL PORT MULTIFUNCTION CNC BOARD Rev. 4

USER S MANUAL. C32- DUAL PORT MULTIFUNCTION CNC BOARD Rev. 4 USER S MANUAL C32- DUAL PORT MULTIFUNCTION CNC BOARD Rev. 4 August, 2012 USER'S MANUAL TABLE OF CONTENTS Page # 1.0 FEATURES... 1-1 2.0 SPECIFICATIONS... 2-3 3.0 BOARD DESCRIPTION... 3-4 4.0 FUNCTIONAL

More information

Antenna Rotator System

Antenna Rotator System Antenna Rotator System Setup & Hardware Reference Manual May/2002 Rev 2.1c Introduction Thank you for purchasing the ARS interface. ARS is the most powerful, high performance and low cost universal rotator

More information

S125 Multi-Purpose 125 KHz RFID Reader USER MANUAL. 9V/24V DC Operating Voltage, AC (optional) KHz RFID EM4100/2 Cards & Tags

S125 Multi-Purpose 125 KHz RFID Reader USER MANUAL. 9V/24V DC Operating Voltage, AC (optional) KHz RFID EM4100/2 Cards & Tags S125 Multi-Purpose 125 KHz RFID Reader 44 mm USER MANUAL MULTI PURPOSE 84 mm ONLINE & OFFLINE MODE BUILT-IN RELAY 125 KHz RFID EM4100/2 Cards & Tags 9V/24V DC Operating Voltage, AC (optional) 3 Online

More information

Minimum 360 in-lb torque - GK. Minimum 54 in-lb torque - NKQ. Minimum 101 lbf - AHQ. Electronic Fail-Safe Series Direct Coupled Actuators

Minimum 360 in-lb torque - GK. Minimum 54 in-lb torque - NKQ. Minimum 101 lbf - AHQ. Electronic Fail-Safe Series Direct Coupled Actuators Electronic Fail-Safe Series Direct oupled ctuators Minimum 360 in-lb torque - GK For damper areas up to 90 sq. ft* Minimum 54 in-lb torque - NKQ For damper areas up to 12 sq. ft* Minimum 101 lbf - HQ ll

More information

E600 VX01 Installation guide

E600 VX01 Installation guide E600 VX01 Installation guide illuminfx Dimensions 2007 Viso Systems ApS, Denmark All rights reserved. No part of this manual may be reproduced, in any form or by any means, without permission in writing

More information

Installation and Operation Manual

Installation and Operation Manual Installation and Operation Manual Thank you for choosing the. This combination of a digital recorder, camera and microphone into one package is a breakthrough in size, cost and convenience. Totally solid-state,

More information

Trouble Shooting Leveling Control Box Electric Jacks. Touch Pad LED Probable Cause Solution

Trouble Shooting Leveling Control Box Electric Jacks. Touch Pad LED Probable Cause Solution Trouble Shooting Leveling Control Box 140-1224 Electric Jacks Copyright Power Gear Issued: January 2013 #82-L0524, Rev. OA Touch Pad LED Probable Cause Solution 1. On/Off LED will not light 2. Wait LED

More information

DMX CONTROLLED RELAY K8072

DMX CONTROLLED RELAY K8072 Total solder points: 167 Difficulty level: beginner 1 2 3 4 5 advanced DMX CONTROLLED RELAY K8072 f the means o ol. y b y la a re 2 protoc Control DMX51 wn well-kno ILLUSTRATED ASSEMBLY MANUAL Total solder

More information

Keep all manuals as a product component during the life span of the product. Pass all manuals to future users / owners of the product.

Keep all manuals as a product component during the life span of the product. Pass all manuals to future users / owners of the product. KC1 Quick Start Edition: June 2012, Revision A Valid for Hardware Revision A Patents Pending Part Number 903-400000-00 Keep all manuals as a product component during the life span of the product. Pass

More information

Products no longer available

Products no longer available echnical data sheet NVF4-MF(-E)-R Modulating linear actuator with emergency function for -way and 3-way globe valves Actuating force 800 N Nominal voltage AC/DC 4 V Modulating control DC 0... 10 V Position

More information

KDR00101 DMX Controlled Relay Kit

KDR00101 DMX Controlled Relay Kit KDR00101 DMX Controlled Relay Kit This is a DMX512-A relay kit using ANSI approved RJ-45 connectors for DMX networks. Power requirements are 12 Vdc @ 100 ma. The relay contact rating is 10 Amp @ 120 or

More information

Resolver to Digital Expansion Board

Resolver to Digital Expansion Board Resolver to Digital Expansion Board Catalog No. EXB009A01 Installation and Operating Manual 6/98 MN1313 Table of Contents Section 1 General Information............................. 1-1 Introduction....................................

More information

Power 3x230VAC DELTA

Power 3x230VAC DELTA 7 8 L /. L /. -Q Main swith - - - - - - -7 P /. - - -K Main ontator -9-8 - () () () () iruit reaker - -0 () () - -7 - -9 - - L /. -K: /8. -K: /8. UL /. UN /. L /8. L /8. - -XL0 L L L P - - a M:0/07/0.0.0

More information

NSI DIGITAL DIMMING SYSTEM DDS 5300 / 5600 DIMMER PACK

NSI DIGITAL DIMMING SYSTEM DDS 5300 / 5600 DIMMER PACK INTRODUCTION NSI DIGITAL DIMMING SYSTEM INSTALLATION AND OPERATION GUIDE The NSI DDS 5300 and DDS 5600 dimmers represent a key part of a state of the art, integrated lighting control system. These dimmers

More information

SRI-02 Speech Recognition Interface

SRI-02 Speech Recognition Interface SRI-02 Speech Recognition Interface Data & Construction Booklet The Speech Recognition Interface SRI-02 allows one to use the SR-07 Speech Recognition Circuit to create speech controlled electrical devices.

More information

Digital Lighting Systems, Inc Protocol Dimming System PROTOCOL. System Planning & Hardware INSTALLER MANUAL. PHM Rev. C - 8/02

Digital Lighting Systems, Inc Protocol Dimming System PROTOCOL. System Planning & Hardware INSTALLER MANUAL. PHM Rev. C - 8/02 Digital Lighting Systems, Inc Protocol Dimming System PROTOOL System Planning & Hardware INSTALLER MANUAL J3 J J3 J Rev. - /02 TABLE OF ONTENTS I- INTRODUTION... II- SYSTEM PLANNING A- Features and apabilities...

More information

Millennium Simplicity Elite Parameter Points and Quirks

Millennium Simplicity Elite Parameter Points and Quirks Millennium Simplicity Elite Parameter Points and Quirks How to access, view and change parameter settings Program Button Test Reset UP Alarms Change Data Address Down 1. Push the Program button once. The

More information

L-80 SERIES HOME & COMMERCIAL HIGH-TECH ENTERTAINMENT CENTER DIAGNOSTIC ADDENDUM

L-80 SERIES HOME & COMMERCIAL HIGH-TECH ENTERTAINMENT CENTER DIAGNOSTIC ADDENDUM 111 Canfield Avenue Randolph, New Jersey 07869 1-800-LANDICE FAX 973-927-0630 L-80 SERIES HOME & COMMERCIAL HIGH-TECH ENTERTAINMENT CENTER DIAGSTIC ADDENDUM High-Tech Entertainment Center Explosion Part

More information

! " Samples of the following reports are included.

!  Samples of the following reports are included. 1 Report Samples ppendix This section contains representative samples of the reports available in your Library Master module. You may want to review the descriptions and report contents before setting

More information

HXV SERIES HIGH VOLTAGE SWITCHING SYSTEMS

HXV SERIES HIGH VOLTAGE SWITCHING SYSTEMS BULLETIN HXV (v) HXV SERIES HIGH VOLTAGE SWITHING SYSTEMS The HXV Series are computer controlled switching systems designed for High Voltage applications. Standard systems handle signals up to volts, while

More information

508 SERIES MICROPHONE STATIONS

508 SERIES MICROPHONE STATIONS INSTALLATION INSTRUCTIONS GENERAL DESCRIPTION The IED 508 Series microphone stations utilize either a two or three layer stacked printed circuit board design in which, with the exception of the desktop

More information

MULTIPOWER MANUAL. Designed and Manufactured by ITEC Tontechnik und Industrieelektronik GesmbH 8200 Laßnitzthal 300 Austria / Europe

MULTIPOWER MANUAL. Designed and Manufactured by ITEC Tontechnik und Industrieelektronik GesmbH 8200 Laßnitzthal 300 Austria / Europe MANUAL Designed and Manufactured by ITEC Tontechnik und Industrieelektronik GesmbH 8200 Laßnitzthal 300 Austria / Europe Dear Customer! The power output stages of the product line ITEC MULTIPOWER are well-known

More information

Universal Process Controller

Universal Process Controller Data Sheet SS/_9 Universal Process ontroller Single output, Heat/ool or Motorized Valve control one controller for every PID control application 9 program, segment Ramp/Soak comprehensive set point profiling

More information

KDR00301 DMX Controlled Relay Kit

KDR00301 DMX Controlled Relay Kit KDR00301 DMX Controlled Relay Kit This is a DMX512-A relay kit using ANSI approved RJ-45 connectors for DMX networks. Power requirements are 12 Vdc @ 200 ma. The relay contact rating is 10 Amp @ 120 or

More information