efesotomasyon.com - Klockner Moeller - inverter Application Note Simatic S7 Siemens AG 2005, all rights reserved

Size: px

Start display at page:

Hubert O’Connor’
5 years ago
Views:

MSystem Application Note Simatic S7 Simatic S7 Siemens AG 2005, all rights reserved Micro Innovation AG Spinnereistrasse 8-14

2 Copyright Copyright Keep documentation for future use This documentation is the intellectual property of Micro Innovation AG, which also has the exclusive copyright. Any modification of the content, duplication or reprinting of this documentation, as well as any distribution to third parties can only be made with the express permission of Micro Innovation AG. Micro Innovation AG does not accept any liability for damages arising from the use of any incorrect or incomplete information contained in this documentation or any information missing therefrom. Micro Innovation AG reserves the right to make complete or partial modifications to this document. All brand and product names are trademarks or registered trademarks of the owner concerned. 2 by Micro Innovation

3 Proper use Proper use Hardware, software, operating systems and drivers must only be used for the applications specified and only in conjunction with the components recommended by Micro Innovation AG. Warning No warranty claims will be recognised for faults arising from the improper handling of devices and modules. The devices, even by means of communication, should not be used for the implementation of any safety functions relating to the protection of personnel and machinery. No liability is accepted for claims for damages arising from a failure or functional defect in the device. All data specified in this document does not represent warranted properties in the legal sense. by Micro Innovation 3

4 Contents Contents 1 General Aim and purpose of this document List of documents Operating Principle Overview MICRO PANEL in the MPI network MICRO PANEL in the Industrial Ethernet network Addressing Data block size Memory alignment Status refresh Default Slot Siemens MPI Hardware requirements Select PLC Baud rate MMI station number Highest station address (HSA) Driver version Siemens MPI (OnBoard) Hardware requirements Select PLC Baud rate MMI station number Highest station address (HSA) Siemens Industrial Ethernet General Hardware requirements Select PLC Startup delay MPI/PROFIBUS station number MPI/PROFIBUS S7 subnet ID IP address Errors Error messages Rectification Change List by Micro Innovation

5 General 1 GENERAL 1.1 AIM AND PURPOSE OF THIS DOCUMENT This documentation describes the connection of a MICRO PANEL to a SIMATIC S7 PLC via the MPI or Ethernet interface. Refer to the MICRO PANEL device description for further information on connecting, commissioning and operating the MICRO PANEL. You must be familiar with the use of the following software which must already be installed: SIMATIC STEP 7 PLC programming software from Siemens Galileo HMI programming software Refer to the Galileo documentation or the online help for further information on Galileo and GRS. The Galileo dialogs shown are from version LIST OF DOCUMENTS Document Doc. No. [1] Installation instructions, General wiring instructions M [2] System description, Networks in brief M [3] System description, Windows CE image version x.xx M [4] Card description, MPBx-TP multi protocol board M [5] User manual, S7 PG router M (this list of documents is not final) by Micro Innovation 5

6 Operating Principle 2 OPERATING PRINCIPLE 2.1 OVERVIEW This documentation describes the following three possible communication methods: Siemens MPI for MICRO PANELs using the MPB2-TP communication card. Siemens MPI (OnBoard) for MICRO PANELs with an OnBoard MPI interface. Siemens Industrial Ethernet for MICRO PANELs with an Ethernet interface. 2.2 MICRO PANEL IN THE MPI NETWORK A direct connection to the SIMATIC S7 is made at the programming port of the CPU (MPI). No parameter settings or function blocks are required for this connection. As soon as the MICRO PANEL is connected to the MPI network, this is indicated with the configured MPI station number in the PG device under Accessible Nodes. However is not possible to make a connection to this station using the programming device. If this is nevertheless attempted, the MICRO PANEL will refuse the connection and the programming device will indicate Station refuses connection establishment. The MICRO PANEL can establish an active connection simultaneously with up to 42 MPI stations (SIMATIC S7 PLCs). The SIMATIC PLC only supports a limited number of MPI connections, depending on the CPU in use. Each MICRO PANEL uses one OP (operator panel) connection. PG MICRO PANEL ST0 ST1 ST3 ST2 ST4 ST5 The following are the standard address settings in the MPI network: MPI address 0 is reserved for the SIMATIC PG. MPI address 1 is the default setting for an Operator Panel (MMI) MPI address 2 is the default setting for a PLC MPI address 3 up to HSA (highest station address) available as required 6 by Micro Innovation

Operating Principle 2.3 MICRO PANEL IN THE INDUSTRIAL ETHERNET NETWORK A direct connection to the SIMATIC S7 is made at the Ethernet port of the CPU or the CP.

7 Operating Principle 2.3 MICRO PANEL IN THE INDUSTRIAL ETHERNET NETWORK A direct connection to the SIMATIC S7 is made at the Ethernet port of the CPU or the CP. No additional parameter settings or function blocks are required for this connection. It is also possible to use a router to communicate with other PLCs in the MPI/PROFIBUS network. This requires a station in the Ethernet network to carry out this router function, and a SIMATIC S7 station with an Ethernet and MPI/PROFIBUS interface or a MICRO PANEL with Ethernet and MPI-OnBoard interface can be used for this purpose. Further information on using a MICRO PANEL as a router is available in the S7 PG Router manual [5]). The MICRO PANEL can establish an active connection simultaneously with several stations (SIMATIC S7 PLC). The SIMATIC S7 PLC only supports a limited number of connections, depending on the CPU in use. Each MICRO PANEL uses one OP connection Ethernet Router oder ST 5 MPI/PROFIBUS ST 31 MPI/PROFIBUS ST 2 ST 4 Station and IP addresses are given as examples. It is essential that every station has a unique and unambiguous station and/or IP address. by Micro Innovation 7

Operating Principle 2.4 ADDRESSING The addressing is implemented using the SIMATIC syntax and all commonly available data types are supported. Addressing format without station number AB %d.%d EB %d.

8 Operating Principle 2.4 ADDRESSING The addressing is implemented using the SIMATIC syntax and all commonly available data types are supported. Addressing format without station number AB %d.%d EB %d.%d MB %d.%d DB %d.dbx %d.%d DB %d.dbb %d DB %d.dbw %d DB %d.dbd %d Addressing format with station number ST %d:ab %d.%d ST %d:eb %d.%d ST %d:mb %d.%d ST %d:db %d.dbx %d.%d ST %d:db %d.dbb %d ST %d:db %d.dbw %d ST %d:db %d.dbd %d Data area Output Input Marker Data access in data block Data area Output Input Marker Data access in data block The placeholder %d represents a decimal number which must be entered for addressing the individual tags. The ST entry defines the station number in the MPI/PROFIBUS network. If no station number is specified in the address, the standard station number from the Select PLC dialog is used. Driver version * 2.00 is required when using the MPB2-TP communication card and the addressing format without station number. 8 by Micro Innovation

Operating Principle If a station number is specified in the address, the standard station number from the Select PLC dialog is not relevant for this tag.

5 DATA BLOCK SIZE The smallest possible format is 8-bit or 1-byte format. Single bit communication is therefore not possible.

9 Operating Principle If a station number is specified in the address, the standard station number from the Select PLC dialog is not relevant for this tag. The tag import of the symbol file is supported from Galileo V Further information is provided in the Galileo documentation. 2.5 DATA BLOCK SIZE The smallest possible format is 8-bit or 1-byte format. Single bit communication is therefore not possible. The maximum size of a data block depends on the type of communication selected. The structure and array size defined in Galileo is therefore restricted to this maximum value. The PLC Data tab in the Select PLC... dialog shows all the data block sizes that are supported. Data types >8 bits can only be set on even addresses. by Micro Innovation 9

10 Operating Principle 2.6 MEMORY ALIGNMENT The memory alignment defines how the individual tags of a structure are stored in the memory of a PLC. Siemens data blocks are normally defined with a 2-byte memory alignment. Refer to the Galileo documentation or the Galileo Online Help for further information on memory alignment. 2.7 STATUS REFRESH The Status refresh defines the maximum refresh time in seconds of the status structure. If the MMI status does not change within the refresh time, the status structure is transferred to the PLC anyway. This is necessary if bit 0 is used in the status structure in order to monitor the connection to the MMI. A default setting of 10s is recommended. Further information on this subject is provided in the Galileo documentation. The shorter the refresh time, the more this will burden communication between the panel and the PLC. This may create a situation in which only the status structure is transferred. 2.8 DEFAULT SLOT If a direct connection to the SIMATIC S7 is made at the programming port of the CPU (MPI), the value can be set to 0. Otherwise the slot number of the target CPU in the rack is to fill in. Rack 0 corresponds to 1..31, rack 1 corresponds to etc. This setting has validity for all stations of a connection. 10 by Micro Innovation

11 Siemens MPI 3 SIEMENS MPI 3.1 HARDWARE REQUIREMENTS This communication method requires the use of the MPB2-TP communication card and therefore requires the use of a MICRO PANEL with a communication slot. Refer to the Multi Protocol Board card description for information on configuring and commissioning the MPB2-TP communication card [4]. Refer to the document Installation instructions, General wiring instructions for information on the communication cable [1]. 3.2 SELECT PLC The MPB2-TP communication card supports only one connection. Several connections cannot therefore be configured on the same interface. with several PLCs is possible in the MPI network, however addressing the system structures is limited to one PLC in the MPI subnet. For this, select Siemens MPI in the Select PLC... dialog. The dialog shown will then appear for setting the parameters required for this communication. Parameter setting for Status Refresh ( chap. 2.7) Parameter setting for Default Station Number ( chap. 2.4) Parameter setting for Default Slot ( chap.2.8) by Micro Innovation 11

Siemens MPI 3.2.1 BAUD RATE Only a baud rate of 187.5kB is supported. The baud rate must correspond to the baud rate setting of the MPI subnet in the SIMATIC Manager of STEP 7. 3.2.2 MMI STATION NUMBER Station number of the MICRO PANEL in the MPI subnet.

12 Siemens MPI BAUD RATE Only a baud rate of 187.5kB is supported. The baud rate must correspond to the baud rate setting of the MPI subnet in the SIMATIC Manager of STEP MMI STATION NUMBER Station number of the MICRO PANEL in the MPI subnet. This must be set between 1 and the HSA. It must also be ensured that each station in the MPI subnet is assigned a unique MPI address. In all cases check with the SIMATIC PG device under Accessible Nodes which addresses have already been assigned HIGHEST STATION ADDRESS (HSA) The highest MPI address setting is used to optimise the MPI subnet. This setting must correspond to the highest MPI address setting of the MPI subnet in the SIMATIC Manager of STEP 7. The following values are possible: 15,31,63, DRIVER VERSION The name and version of the driver file are displayed in the PLC Data tab of the Select PLC... dialog. The driver file must be loaded on the MPB2-TP communication card. The version of the driver loaded on the MPB2-TP communication card is indicated when the application is started up on the MICRO PANEL. The loaded driver version is also displayed in a system message ( chap. 6.1). Refer to the Multi Protocol Board card description for information on loading the driver file and other settings required for the MPB2-TP communication card [4]. 12 by Micro Innovation

13 Siemens MPI (OnBoard) 4 SIEMENS MPI (ONBOARD) 4.1 HARDWARE REQUIREMENTS This communication method requires a MICRO PANEL with an MPI OnBoard interface. Refer to the document "Installation instructions, General wiring instructions" for information on the communication cable [1]. At least 40 additional license points must be available on the device, regardless of the number of connections! If you have any questions on license products, please contact your local MICRO PANEL sales distributor. 4.2 SELECT PLC The OnBoard interface supports several connections, i.e. several connections can therefore be configured on the same interface. This makes it possible to address the tags including the system structures on several PLCs in the MPI network. Baud rate, MMI station number and HSA must be identical on all connections. For this, select Siemens MPI (OnBoard) in the Select PLC... dialog. The dialog shown will then appear for setting the parameters required for this communication method. Parameter setting for Status refresh ( chap. 2.7) Parameter setting for Default station number ( chap. 2.4) Parameter setting for Default Slot ( chap.2.8) by Micro Innovation 13

14 Siemens MPI (OnBoard) BAUD RATE 187.5kB and 1.5MB are supported. The baud rate must correspond to the baud rate setting of the MPI subnet in the SIMATIC Manager of STEP MMI STATION NUMBER Station number of the MICRO PANEL in the MPI network. This must be set between 1 and the HSA. It must also be ensured that each station in the MPI subnet is assigned a unique MPI address. In all cases check with the SIMATIC PG device under Accessible Nodes which addresses have already been assigned HIGHEST STATION ADDRESS (HSA) The highest MPI address setting is used to optimise the MPI subnet. This setting must correspond with the highest MPI address of the MPI subnet in the SIMATIC Manager of STEP 7. The following values are possible: 15,31,63, by Micro Innovation

15 Siemens Industrial Ethernet 5 SIEMENS INDUSTRIAL ETHERNET 5.1 GENERAL At least one of the following versions of the SIMATIC Manager is required in order to use the Industrial Ethernet: a) STEP 7 V5.2 + Net driver b) STEP 7 V5.3 Further information on creating and configuring a SIMATIC network is provided in the Help system of the SIMATIC Manager and SIMATIC NetPro. Before creating a connection with a MICRO PANEL to a SIMATIC S7 PLC, you should ensure that the SIMATIC S7 PLC is accessible from the SIMATIC PG on the network. 5.2 HARDWARE REQUIREMENTS This communication method requires a MICRO PANEL with an Ethernet interface. Refer to Ethernet in the document Installation instructions, General wiring instructions for information on the communication cable [1]. At least 80 additional license points must be available on the device, regardless of the number of connections! If you have any questions on license products, please contact your local MICRO PANEL sales distributor. by Micro Innovation 15

Siemens Industrial Ethernet 5.3 SELECT PLC The Ethernet interface supports several connections, i.e. several connections can therefore be configured on the same interface.

16 Siemens Industrial Ethernet 5.3 SELECT PLC The Ethernet interface supports several connections, i.e. several connections can therefore be configured on the same interface. This makes it possible to address the tags including the system structures on several PLCs in the MPI/PROFIBUS network. For this, select Siemens Industrial Ethernet in the Select PLC... dialog. The dialog shown will then appear for setting the parameters required for this communication. Parameter setting for Status refresh ( chap. 2.7) Parameter setting for Default station number ( chap. 2.4) Parameter setting for Default Slot ( chap.2.8) STARTUP DELAY During this time, error messages concerning communication are suppressed. This is useful if the startup of the SIMATIC S7 station takes longer than the startup of the MICRO PANEL. After startup, the MICRO PANEL immediately tries to start communication. An error message, however, is only generated after the set time has elapsed. If a startup delay of >0 is set, a green system message will appear as soon as communication is successful started. If there is no communication to the CP/CPU established, check the accessibility of the CP/CPU with the PING command. 16 by Micro Innovation

Siemens Industrial Ethernet 5.3.2 MPI/PROFIBUS STATION NUMBER This is where the station number is entered for the station defined as the router in the MPI/PROFIBUS subnet.

17 Siemens Industrial Ethernet MPI/PROFIBUS STATION NUMBER This is where the station number is entered for the station defined as the router in the MPI/PROFIBUS subnet. This can be a MICRO PANEL or a SIMATIC S7 station. The following example shows communication with a SIMATIC S7 station used as the router. Station number 31 must be entered for communication with station 2 and 31. The following example shows communication with a MICRO PANEL station used as the router. Station number 31 must be entered for communication with station 2. by Micro Innovation 17

18 Siemens Industrial Ethernet In the following example with a PLC directly on the Ethernet network, communication with station number 5 consequently requires 5 to be entered. 18 by Micro Innovation

via a router. In the following example, this would be required for station number 2.

19 Siemens Industrial Ethernet MPI/PROFIBUS S7 SUBNET ID The MPI/PROFIBUS S7 subnet ID only has to be entered if a PLC in the MPI/PROFIBUS subnet is to be accessed via a router. In the following example, this would be required for station number 2. If the PLC is accessible directly via the Ethernet network, no subnet ID has to be entered. The MPI/PROFIBUS S7 subnet ID is shown in the SIMATIC network configuration, and must not be confused with the Ethernet S7 subnet ID. (Dialog is from the SIMATIC Manager of STEP 7) by Micro Innovation 19

Siemens Industrial Ethernet 5.3.4 IP ADDRESS The IP address entry must match the setting of the SIMATIC station or the MICRO PANEL with a PG router function.

20 Siemens Industrial Ethernet IP ADDRESS The IP address entry must match the setting of the SIMATIC station or the MICRO PANEL with a PG router function. This is the IP address of the router and the station on the Ethernet network. The following example requires the configuration of 2 connections: 1. Connection to station number 2 and 31, must be entered. 2. Connection to station number 5, must be entered. (Dialog is from the SIMATIC Manager of STEP 7) The subnet mask of the MICRO PANEL must be suitable for the subnet mask of the SIMATIC S7 station. For further information on setting the IP address of the MICRO PANEL refer to the "System description Windows CE Image Version x.xx" [3]. 20 by Micro Innovation

21 Errors 6 COMMUNICATION ERRORS 6.1 ERROR MESSAGES Different system error messages are generated in response to any communication errors that occur. These system error messages provide different information: The tag name indicates the tag in which a problem was found. The interface information indicates the MICRO PANEL interface on which the problem was found. The driver version indicates which communication driver is active. The station number after ST# corresponds to the MPI address of the affected PLC (CPU). The additional information may indicate the possible cause of an error in plain text. This information can, however, also be generated from lower software layers. Its content can therefore only be interpreted with an in-depth knowledge of the system. The troubleshooting procedure is nevertheless the same in all cases. Tag name Interface Driver version Station number Additional error information 6.2 RECTIFICATION Checking the following points is recommended: Check the cabling and the connections on the MICRO PANEL and the PLC. When using a communication card, check the jumper settings and driver loaded with the version on the card ( chap.3.2.4). Check the baud rate and HSA settings. These settings must be the same on all stations. Check all other parameters in the Select PLC... dialog. Check the MPI addresses in the network. Is the station number indicated in the system error message present or available in the MPI/PROFIBUS network? An address must only be present once. Is the address of the tag indicated in the system error message present in the corresponding station? (is the corresponding DB present?) Is the Ethernet communication overloaded? Is the PLC (CPU) accessible via the SIMATIC PG device? Is the PLC (CPU/CP) accessible via Ethernet via PING command? If the problem continues, contact our Customer Support at support@microinnovation.com. by Micro Innovation 21

22 Change List 7 CHANGE LIST Index Date / Signed Modifications / As Initial version / As PROFIBUS and Default Slot added 22 by Micro Innovation

23 Change List by Micro Innovation 23

24 Change List Micro Innovation AG Spinnereistr 8-14 CH-9008 St. Gallen Switzerland Tel : Fax : info@microinnovation.com homepage : 24 by Micro Innovation

Communication Allen Bradley Logix

User Manual 12/2010 MN04802021Z-EN replaces M001805-01, 02/2007 Communication Allen Bradley Logix Imprint Manufacturer Eaton Automation AG Spinnereistrasse 8-14 CH-9008 St. Gallen Schweiz www.eaton-automation.com