SmartCam D1. Installation Guide Part 1: Doorbell Setup

Transcription

1 1 SmartCam D1 Installation Guide Part 1: Doorbell Setup

2 SmartCam D1 Overview Thank you for purchasing the SmartCam D1 Video Doorbell. To get you started with your doorbell, please follow the steps below. 1 Check page 3 to see the list of compatible chimes. 2 Follow the instructions on pages 7-8 to connect the Power Stabilizer Kit to your existing mechanical/electrical chime. 3 Install the doorbell by following the instructions on pages Download the Wisenet SmartCam+ app for app setup. 5 Once app setup is complete, follow the instructions on page 14. 2

3 SmartCam D1 - Home Chime Compatibility List Check the compatibility list below before installation. Most mechanical chimes share the same composition except for chimes with special functions. To find out the latest compatible chime list with Smartcam D1, check out the FAQ. ( > SNH-V6435DN > FAQ) Compatible chime Chime type Manufacturer Model Description Heath-Zenith SL-2796 Carlon DH506 DH120 Craftmade C102X2L Edwards C212W-2L for RCW110N (Honeywell) Mechanical Honeywell NuTone Atlantic RCW100N RCW110N LA11WH LA14WH BK125LWH-1 BK115LWH BK131LPB LA70MA Al BCK1-PWH Power Stabilizer for LA70MA (NuTone) Power Stabilizer 0(F) 1 3(T) 2 Common Trans Front Smartcam D1 AC 16V Smartcam D1 AC 16V 3 Chime type Manufacturer Model Description Heath-Zenith DC-3338 for RCW3501N (Honeywell) AC Electrical Incompatible chime Honeywell IQ America Nutone RCW3501N RCW3505N DW1402A LA600WH Power Stabilizer Chime type Manufacturer Model Description C210 Edwards Mechanical C210-W Nicor Electrical NuTone LA174WH V/AC C1 C2 C3 Smartcam D1 AC 16V

4 What s in the box Warranty Card / GPL License / Quick Start Guide Faceplate (Gold/Silver/Black) * Power Stabilizer Kit for Mechanical/Electrical Chimes Screw Driver / Drill Bit Security Screws / Faceplate Screws / Plastic Anchors SmartCam D1 * Power Extension Kit Power Extender Connectors (Terminal Blocks) for D1 / Power Extender Cables for D1 Power Stabilizer Connectors (Terminal Blocks) VIDEO DOORBELL Power Stabilizer Power Stabilizer Power Stabilizer Cable 4

5 System Requirements. Wi-Fi a/b/g/n/ac (2.4GHz / 5GHz). Recommended : 2.5Mbps or higher. ios 8 or higher. Android OS 5.0 or higher. Requires existing hardwired Mechanical/ Electrical chime bell.. Requires wiring to a VAC Transformer. 5

6 SmartCam D1 Overview 1 Faceplate Illumination Sensor 2 2 Microphone RESET Wi-Fi Direct Button LED Status Indicator Bell Button 4 5 Power Input 5 1 Speaker Hole Reset Button 4 1 6

7 Connecting the Power Stabilizer to the Chime To see the video installation guide, go to > Products > SmartCam > SmartCam D1(SNH-V6435DN) > Video tab. 1 Open the cover on your existing chime. JJ`` Before you start, you must turn off the circuit breaker for safety purposes. 2 Open the "Power Stabilizer Kit" and insert the wire connector into the Power Stabilizer Box. 3 Use a screwdriver to loosen the screws on the [FRONT] and [TRANS] terminals and then remove the cables. kk `` Make sure to label the terminal cables before disconnecting them. You will need to connect them to the terminal blocks later. VIDEO DOORBELL Power Stabilizer FRONT TRANS REAR Scan the QR code or enter for video instructions to guide you through the D1 doorbell installation process. Download a QR Code app to scan the QR code. 7

8 Connecting the Power Stabilizer to the Chime 4 Connect Power Stabilizer to Chime a Pull up the orange levers on the terminal block. b Insert the Power Stabilizer cable into one of the slots and push the orange lever back down. c Insert the wire labeled Front into the remaining opening of the terminal block. d Attach the L-shaped end of the Power Stabilizer to the [Front] terminal on the Chime. kk `` Make sure the end of the wire is properly aligned to the metal strip before closing the orange lever. 5 Repeat Step 4 for the [Trans] cable. 6 Put the chime cover back on once you are finished. Power Stabilizer cable FRONT FRONT TRANS TRANS REAR REAR Pre-existing chime cable kk `` Make sure to tuck the cables and Power Stabilizer box into an open space within the chime before putting the cover back on. Pre-existing chime cable Power Stabilizer cable FRONT FRONT TRANS REAR 8

9 Mounting the SmartCam D1 1 Use a screwdriver to remove your existing doorbell. Disconnect the wires from behind the doorbell carefully. 2 Mark the position of the mounting holes for your new doorbell. RESET 9

10 Mounting the SmartCam D1 3 Drill the holes about 1.2 inches deep into the wall. (Recommended Drill Bit size is 0.2 inches) 4 Unscrew one of the power terminals on the back of your SmartCam D1, and wrap the existing wiring from your doorbell around the terminal, and then tighten the screw. kk `` It doesn't matter which cable you use on which side of the terminal back. 10

11 Mounting the SmartCam D1 5 Optional Step for Extending Power Supply (Requires Power Extension Kit): a If existing wire is too short, use the Power Cable Extender and connect the flat circular end of it to the terminal, then screw the terminal back on. b Pull the orange levers on the terminal blocks up. c Insert the existing cable from the wall to one of the slots and push the orange lever back down. d Insert the new power cable from the doorbell to the other slot and pull the lever back down in place. e Repeat this process for the other side. 6 Mount and secure your doorbell. a Insert the anchors into the holes completely. b Tuck the wires attached to the doorbell back into the wall and align the two holes on the doorbell with the holes in the wall. c Screw the SmartCam D1 tightly into the wall. kk `` Make sure to remove the faceplate attached to your SmartCam D1 to access the mounting holes. RESET 11

12 Mounting the SmartCam D1 7 Check the diagrams below to make sure the Power Stabilizer and SmartCam D1 are properly installed. 110V Transformer 16V~24V/10VA Trans 110V Transformer Trans VIDEO DOORBELL Power Stabilizer Front Home chime 16V~24V/10VA Front Home chime Power Stabilizer Front door Front door <Before> <After> 12

13 SmartCam D1 Registration & Setting 1 Follow the instructions in Part 2 (App Guide) to set up your account and doorbell. 2 Save your Account and Device information here. 3 Select your doorbell chime type. a Go to the app home screen and locate SmartCam D1 Setting ; General b Tap the Chime bell type. c Select your existing doorbell chime type. Check to make sure your chime bell is properly installed. User ID : User Password : Camera Name : Camera Password : General Apply Camera Name my doorbell Change password You MUST check your chime type and Time set for the same :13:13 If you try out for Mechanical or Electrical setting without actually (GMT-05:00) Eastern Time (US & Time zone having the chime installed, the product may get electric damage. Canada) Daylight Saving Time No chime bell Status LED Mechanical Electronic Image encrypting Chime bell type OK Cancel Mechanical Firmware Version Update v1.00_ Camera default Delete camera 13

14 SmartCam D1 Registration & Setting 4 Once you are finished with the in-app setup for the SmartCam D1, attached the faceplate back on. 5 Tighten the screw on the bottom of the SmartCam D1 body to secure the faceplate. RESET 14

15 LED Status Guide Bell LED Status Guide Booting up Booting completed Enabling Wi-Fi Direct Blink Blink Searching for available Wi-Fi network Connected to Wi-Fi network Connected to Server / Setup Completed Download firmware Updating firmware Normal Status Blinks 3-4 times with the chime when pressed ON Blink Dim Blink Slowly dims up & down repeatedly for 10-sec when a person is detected. Blinks every 10 seconds to notify users of power supply issue. Blink 15

16