Programming of PCU-EC, PCU-EC2 cards and all CD Panels
|
|
- Sydney Lane
- 6 years ago
- Views:
Transcription
1 Sida Page 1 (6) Programming of PCU-EC, PCU-EC2 cards and all CD Panels 1. First investigate which version of the hardware you have. If you have the system up and running you can check the version of the software according to point 10 below. If you have CD version below 1.50 means that you have a CD panel. Versions between and means you have the CD2 panel, all versions above is the CD3 panel. EC version 1.x means you have the PCU-EC card and 2.x and higher is the PCU-EC2 card. If you can t see it in the display then you can find out by looking for the following: The PCU-EC2 card has 2 connectors for Modbus and CD2/CD3 panels, those do not exist on the old PCU-EC card. IF WRONG FILES ARE USED FOR YOUR HARDWARE IT MAY BE UNUSABLE!! PCU-EC PCU-EC2 For the CD, CD2 and CD3 panels you have to take off the casing and remove the turning knob, then look at the text on the small processor: The CD panel has the text ATMEL MEGA644P The CD2 and CD3, ATMEL MEGA1284P
2 Sida Page 2 (6) It is unfortunately not possible to see any hardware difference between CD2 and CD3, but CD3 is for use with SAVE VTR/VSR units, and CD2 with VR/VTC units. 2. Connect your USB programming device (Systemair art.nr 7898) to the PC and to the pins on the PCU-EC(2) card labeled USB, the red stripe on the cable should be on the side marked 1 on the card. Also connect your CD(x) panel. In case it is the first time you connect the USB programming device you may need some drivers which you can receive from your service contact at Systemair. If you should get a message saying ftd2xx.dll missing go to the following page and download the appropriate driver for your PC: 3. Open the latest version of the Monitor program, available from your service contact at Systemair. Power up the PCU-EC(2) card, if the communication works correctly your top left corner of the window should look something like this, numbers coming up and the USB detected checkbox checked. If the USB detected checkbox is not marked, there is something wrong with the setup of the programming device, sometimes it is needed to unplug the USB connector to the PC and put it back again and also restart of the monitor program may be neccesary. If it is checked and no numbers are coming up, there is something wrong with the communication between your programming device and the PCU-EC(2) card, try turning off and on the power to the PCU-EC(2) card and make sure your cable is connected properly on the USB pins.
3 Sida Page 3 (6) 4. Go to the Programming tab in the monitor program 5. Load the latest file for the PCU-EC(2) card by pressing the Load File button as seen below: Make sure you know which hardware you have according to point 1 in this document so you receive the correct files from your service contact at Systemair. Do not change the checkbox settings below the Load File button. IF WRONG FILES ARE USED FOR YOUR HARDWARE IT MAY BE UNUSABLE!! 6. Load the latest file for the CD(x) panel by pressing the Load File button as seen below: In case you have a PCU-EC2 card and a CD panel, some functions will work, some functions will not work, so it is highly recommended to change your CD panel to a CD2 panel. Make sure you know which hardware you have according to point 1 in this document so you receive the correct files from your service contact at Systemair. Do not change the checkbox settings below the Load File button. IF WRONG FILES ARE USED FOR YOUR HARDWARE IT MAY BE UNUSABLE!!
4 Sida Page 4 (6) 7. Press the Start programming button During this process, DO NOT PRESS ANY BUTTONS ON THE CD(x) Panel! Once the counter Page # has reached 239 for the PCU-EC or 255 for the PCU-EC2 the programming of the PCU-EC(2) card is done Now look at your CD(x) panel, it should look like this: Press the top left button to start loading the CD(x) panel, and the counter will stop at Page # 239 for the CD panel, and 495 for the CD2 and CD3 panel.
5 Sida Page 5 (6) 8. Turn the power off on the system and then turn it back on. 9. Go to the tab Production and choose the unit you have, or wish to use this card for then press the Config System button 10. To make sure everything has been programmed properly, use the CD(x) panel and check the version and unit type by turning the knob so the service menu choice is highlighted, the icon to the right and then pressing the top left button the CD(x) panel. Then scroll down with the knob to the Version menu choice and press the top left button
6 In this page you should now see the correct system type as you configured earlier, and the version of the PCU-EC(2) and the CD(x) panel files. Sida Page 6 (6)
GSC400 Series. GSC400 Programmer and PC Interface User Manual
GSC400 Series GSC400 Programmer and PC Interface User Manual GSC400 Programmer and PC Interface User Manual Full Version File: GSC400 PC Interface Rev1.2.doc, August 2009 2 of 33 Amendments Issue Section
More informationSetting up the PC ready for BESA 11
Setting up the PC ready for BESA 11 1 - Installing Driver. Important Note: Before you start to install the driver, please do not plug BESA 11 into the computer s USB port or else the installation will
More informationProject VALHALL. VR400/700DC/DCV VR400/700DC/DCV- VTC300/700 SAVE Units. Modbus - No startup wizard
2014-10-29 APPROVED AND LAUNCHED PROGRAM VERSIONS This document shows which version is the current, and also release dates and versions history. The current software is marked with orange background and
More informationMadgeTech 4 Software User Guide:
MadgeTech 4 Software User Guide: Getting to Know the Software: Here is a starting screenshot of the MadgeTech 4 software. As you can see in the figure, there are three main tabs in the top left. In the
More informationTech Memo # Software Engineering. Normal PRIORITY: DATE: April 17 th, 2015
Software Engineering Tech Memo #15-0001 PRIORITY: Normal DATE: April 17 th, 2015 TITLE: PRODUCTS AFFECTED: TOOLS REQUIRED: NOTE: INTRODUCTION: How to install and configure Adaptive Sign Server on a Windows
More informationATS e-track Certified BAFX
Driver: Before you start, you must have a Driver Login, Password and Vehicle ID from your Administrator. Any other apps running on this tablet/phone that communicate to the BAFX must be stopped and shutdown.
More informationNew Functions in Version 2.0 Nouvelles Fonctions de la Version 2.0 Neue Funktionen in Version 2.0
New Functions in Version 2.0 Nouvelles Fonctions de la Version 2.0 Neue Funktionen in Version 2.0 o [ W 2.0 V @ \ E F G J 1 Several new functions have been added to version 2.0 for Trinity series music
More informationTechnical Bulletin DS2
Product: DS-Matrix Software TB 221 Date: July 25 th, 2012 Subject: How to Upgrade DS-Matrix Software This document describes the procedure for upgrading the DS-Matrix software. If you are upgrading from
More informationModule 2, Add on lesson Introduction to the NXT and Mindstorms software. Student. 45 minutes
Module 2, Add on lesson Introduction to the NXT and Mindstorms software Student 45 minutes Purpose of this lesson Write a basic program using LEGO Mindstorms Download and run programs on the NXT Materials
More informationWindows 95/98 Infoway Connection Instructions 1/4/2002; rev. 1/9/2002
Windows 95/98 Infoway Connection Instructions 1/4/2002; rev. 1/9/2002 The following are the basic steps for setting up your computer for a PPP connection to the library s Infoway Internet service. A PPP
More informationHow to refresh a Wireless Profile on your computer
How to refresh a Wireless Profile on your computer This document details how to delete the old Wi-Fi connection profile stored on your computer so it does not conflict with your new Wi-Fi connection When
More informationInstructions for Installing FlashUpdate and Downloading Updates for NPRT 2200 Noise Power Ratio Test Set
Instructions for Installing FlashUpdate and Downloading Updates for NPRT 2200 Noise Power Ratio Test Set Updates to the instrument firmware are available from the Applied Instruments website. Requirements
More informationDataman-S6 - User's Manual. Dataman-S6 Compact USB Programmer User's Manual
Dataman-S6 Compact USB Programmer User's Manual Contents Chapter 1 Product Description 1-1 Introduction 1-2 Safety Information 1-3 Precautions 1-4 Operating System, Hardware Requirements 1-5 Accessories
More informationReports/Invoices/Work Orders/Purchase Orders Do Not Show When Printing
Printer Troubleshooting Document Reports/Invoices/Work Orders/Purchase Orders Do Not Show When Printing Overview: PACCAR Connect uses pop-up windows to show reports in PDF format before you send them to
More informationLOADING DRIVERS FOR SKYVIEW 2.0 XBEE INTERFACE USB DEVICE ON WINDOWS 8
LOADING DRIVERS FOR SKYVIEW 2.0 XBEE INTERFACE USB DEVICE ON WINDOWS 8 After you have loaded the Skyview 2.0 software, with the xbee interface plugged in to your USB drive, you try to start the program
More informationNote: If you try to close the screen by clicking the red x in the top, right corner at this point, the following warning message appears:
Page 1 of 9 Clock Utility The Clock Utility screen allows you to download fingerprint and employee information from your clocks. You can then assign employees in WaspTime to certain clocks. The Clock Utility
More informationMIDX-20 DUAL USB MIDI Host
Assistant PC program V2 MIDX-20 DUAL USB MIDI Host Class Compliant USB MIDI devices Roland/BOSS devices Fender Mustang V2 Amplifiers Boss Katana Amplifiers Download from www.primovasound.com Rev. 2018-05-03
More informationMMI6070 Quick Start Guide
MMI6070 Quick Start Guide Introduction If at any time more information is required on HMI safety and protection ratings, HMI Power, and HMI communication, please refer to the MMI6070 Installation Guide
More informationmenu of icons which you can select which item you want to use to startup the computer.
To begin, insert the media that came with your computer into your CD / DVD drive. While the media is in the computer, power the computer off and restart the system. Upon restart you will need to press
More informationEverything You Wanted To Know About USB Embossers* *but were afraid to ask
Braille2000, LLC 6801 Southfork Cir, Lincoln, NE 68516 Phone: (402) 423-4782, Fax: (402) 423-5154 http://www.braille2000.com Everything You Wanted To Know About USB Embossers* *but were afraid to ask This
More informationEDGE, MICROSOFT S BROWSER
EDGE, MICROSOFT S BROWSER To launch Microsoft Edge, click the Microsoft Edge button (it s the solid blue E) on the Windows Taskbar. Edge Replaces Internet Explorer Internet Explorer is no longer the default
More informationTraining Bulletin TITLE: CHIP-CARD BROWSER RECOMMENDATIONS AUDIENCE: GENERAL MANAGERS, FRONT DESK STAFF DATE: DECEMBER 12. Intro
TITLE: CHIP-CARD BROWSER RECOMMENDATIONS AUDIENCE: GENERAL MANAGERS, FRONT DESK STAFF DATE: DECEMBER 12 Intro As a web-based application, the choiceadvantage Property Management System is impacted by the
More informationWindows NT Server Printer Driver Upgrade Instructions
Windows NT Server Printer Driver Upgrade Instructions The steps detailed below describe the most reliable method to upgrade printer driver versions after v1.6.0227a on a Windows NT 4.0 Server that is shared
More information[Type text] Windows Quick Start Guide Version 3.5
[Type text] Windows Quick Start Guide Version 3.5 PRO-STUDY QUICK START GUIDE Contents The Pro-Study Toolbar... 2 Getting Started with a Project... 3 Selecting Different Projects... 4 Categories... 4 Collecting
More informationNavigating in Windows 10
Navigating in Windows 10 Desktop The Desktop contains shortcuts to Programs which can be customized. Start Button: The Start menu has been expanded in Windows 10 to include Tiles. Programs are listed in
More informationTurningPoint Quick Start Guide
TurningPoint Quick Start Guide Section 1 >> Installing TurningPoint Software Section 2 >> Creating an Interactive PowerPoint Slide Section 3 >> Simulating a Group Response Session Section 4 >> Hardware
More informationLineup Configuration Guide
Lineup Configuration Guide How to Stop the Lineup Display & DSI Software If you need to stop the Lineup display & DSI software to get to the Windows desktop follow these steps. 1. Press the ESC key which
More informationModule 2, Add on lesson Introduction to the NXT and Mindstorms software. Teacher. 45 minutes
Module 2, Add on lesson Introduction to the NXT and Mindstorms software Teacher 45 minutes Purpose of this lesson Write a basic program using LEGO Mindstorms Download and run programs on the NXT Materials
More informationDisassembly and Model Identification Guide
Disassembly and Model Identification Guide Introduction: In this guide we will walk you through the necessary steps to identify the model of your console, and the type of CD drive your console has. Both
More informationCreating a New Cognos Report Request
Creating a New Cognos Report Request Wednesday, January 13, 2016 11:08 AM Creating a Cognos Report Request is simple using the OnBase Cognos Report Request form and will help get your reporting needs met
More informationShadow Custom Software. Scan-N-Send USERS Guide
Shadow Custom Software Scan-N-Send USERS Guide Revision Date: 4/1/2008 Table of Content About Scan-N-Send Page 3 Software Application Installation Page 4-7 Scanner Driver Installation Page 7-11 Scanner
More informationGM2. Shift Button. 4 Assignable Buttons. Hat Switch. Fire Button (Assignable) Scroll Wheel. Assignable Button. Scroll Wheel & Button
GM2 Shift Button 4 Assignable Buttons Hat Switch Fire Button (Assignable) Scroll Wheel Assignable Button Scroll Wheel & Button 3 Assignable Buttons Hat Switch INTRODUCTION Congratulations on your purchase
More informationGSC400 Series. GSC400 Programmer and PC Interface User Manual
GSC400 Series GSC400 Programmer and PC Interface User Manual GSC400 Programmer and PC Interface User Manual Full Version File: GSC400 PC Interface Rev1.5.doc, December 2010 2 of 42 Thank You For Purchasing
More informationWindows Key e: Press and hold down the Windows (Start) Key and tap the letter e one time. Release these keys and Windows File Explorer will open.
Copyright 2009 BOSMA Enterprises Chapter 14 Windows File Explorer Key Terms Windows Key e: Press and hold down the Windows (Start) Key and tap the letter e one time. Release these keys and Windows File
More informationTo administer and edit information regarding your users and their access to the Masternaut system you should click on the Users tab.
I INTRODUCTION This guide details the additional functionality available on the Masternaut website for system administrators. A system administrator is able to configure and edit user profiles including
More informationSection 4: Installing the ECC (Epilog Control Center)
Section 4: Installing the ECC (Epilog Control Center) In This Section Installing the ECC The ECC (Epilog Control Center) provides Job Management features as well as laser control and laser machine configuration
More informationWinDSX New Installations
WinDSX New Installations Use these instructions for new Installations. a) Make sure that the Comm Server PC has the.net Framework 4.0 or higher installed. b) Make sure you have Administrative Privileges
More information1) Installing Bluetooth software for Windows (A) Place installation CD into PC and setup should launch automatically.
1) Installing Bluetooth software for Windows (A) Place installation CD into PC and setup should launch automatically. If setup does not launch, use Windows Explorer to navigate to the appropriate CD- ROM
More informationInstructions for Installing FlashUpdate and Downloading Updates for Super Buddy Satellite Meter
Instructions for Installing FlashUpdate and Downloading Updates for Super Buddy Satellite Meter Updates to the Field Guide and to the instrument firmware are available from the Applied Instruments website.
More informationRoastLogger Arduino/TC4 driver installation for Windows 9/10/13 By John Hannon (JackH) at Homeroasters.org
This procedure was written for the Arduino Uno board with the TC4 shield. Please check the Arduino site for software if you are using a different model. I have not tested it, but this procedure should
More informationHow To Trigger a Relay Group From an Input
In GuardPointPro it is possible to fire a group of relays across multiple controllers from a signal to a single input This guide explains the steps: Grouping the outputs [Relays] 1. Go to the menu Event
More informationEnter your Appserv username and password to sign in to the Website
Appserv Desktop Access Logging on from a Windows 10 Device Step 1. To sign in to the Appserv Desktop Access website, either enter the following address into the Microsoft Edge browser address bar, or click
More informationInstalling and Configuring Xitron RIP Software and Ohio GT RIP Plug-In
TECHNICAL DOCUMENTATION Installing and Configuring Xitron RIP Software and Ohio GT RIP Plug-In For Xitron Navigator RIP version 10.1r2 and Windows 10 Introduction This document gives instructions for installing
More information1 BACKGROUND 2 SETTING UP THE HOME AND GOOGLE DRIVES THROUGH WEBSTORAGE. Using the Home Drive to Save from U5 Cloud Updated 8.31.
Using the Home Drive to Save from U5 Cloud Contents 1 Background... 1 2 Setting Up the Home and Google Drives through webstorage... 1 3 Saving a Document to the Home Drive... 2 4 Finding and Opening Your
More informationCISCO WEBEX CLOUD CONNECTED AUDIO
CONFERENCING & COLLABORATION WEB CONFERENCING CISCO WEBEX CLOUD CONNECTED AUDIO How to Update Previously Scheduled Meetings to CCA SP Audio Once WebEx Cloud Connected Audio is enabled on your Cisco WebEx
More informationUSB SERIAL ADAPTOR COM PORT INSTRUCTIONS
USB SERIAL ADAPTOR COM PORT INSTRUCTIONS No part of this work covered by the copyright hereon may be reproduced, copied, transferred or distributed in any form or by any means -- graphic, electronic, or
More informationInternet Explorer 11 QUICK START GUIDE ADDRESS BAR SEARCH ACCESSING FMS
QUICK START GUIDE While Internet Explorer 11 does not look that much different to what you are used to, there are a few useful features that have been added/enhanced that may make your life easier. ADDRESS
More informationAdministrator s Guide to Publishing Multimedia
Administrator s Guide to Publishing Multimedia The Administrator s Guide to Publishing Multimedia enables the administrator to upload multimedia into CE Manager and make them available to professionals
More informationDATABANK WEB SITE Cod. M0251 Rev. 2.2 (06/2018) User Manual 1. FIRST DATABANK INSTALLATION 2. DATABANK UPDATE
User Manual 1. FIRST DATABANK INSTALLATION 2. DATABANK UPDATE INDEX 0 FOREWORD... 3 1 SETTINGS TO ENABLE THE POP-UPS... 5 1.1 If you have Chrome... 5 1.1 If you have Firefox... 7 1.2 If you have Internet
More informationShopping Cart: Queries, Personalizations, Filters, and Settings
Shopping Cart: Queries, Personalizations, Filters, and Settings on the Shopping Cart Home Page Use this Job Aid to: Learn how to organize the Shopping Cart home page so that it is easier to use. BEFORE
More informationDP-502 User s Guide Harware Descriptions Software Installation ETM 3.0
DP-502 User s Guide This DP-502 (the device ) based system allows multiple devices to connect to a server and automatically update audio contents on a daily basis. The device is loaded with up to 13 sound
More information3. Close the window and all open Internet Explorer windows, then run the session again. Page 1 of 6. Downloaded from
Add the 3 Intermountain domains to the Compatibility View settings in Internet Explorer 9 11 Doing this avoids the majority of HELP2 browser errors & issues Accessing Compatibility View settings in Internet
More informationCustomizing Windows XP
Customizing Windows XP Mouse Moves Click Always lets you select something. It may be an icon, a button, or a menu command. Double Click Click the mouse (or trackpad) 2 times on an icon to open that document
More informationThe USB-to-Serial Converter
The USB-to-Serial Converter Older type with Prolific chipset Current type with FTDI chipset Introduction The USB Serial Converter attaches to a PC USB port and provides a serial port connector, to which
More informationHow to setup Google DNS in your Windows computer
Submitted by Jess on Thu, 01/22/2015-17:08 This is a very common issue with internet connections: you are able to access certain websites and other sites are inaccessible; websites that you used to access
More informationSCP-MOD Quick Reference Guide: Discrete Orders Buyer
SCP-MOD Quick Reference Guide: Discrete Orders Buyer Updated August 2016 Discrete orders are created in the buyer s backend system and then automatically sent to SCP for viewing and response by the supplier.
More informationAirCheck Wi-Fi Tester Evaluation Guide
AirCheck Wi-Fi Tester Evaluation Guide Outline 1. Getting Started 2. Finding Networks and Access Points 3. Drill in on an AP 4. Locate an AP 5. Discover Clients Associated to an AP 6. Locate a Client 7.
More informationWe recommend that you begin on a desktop/laptop computer and then transfer the ebook to your device using the USB cord.
E-Readers (Nook Simple Touch, and other simple e-readers) We recommend that you begin on a desktop/laptop computer and then transfer the ebook to your device using the USB cord. You can access the digital
More informationFSA-CU Configuration Utility Programming Guide
FSA-CU Configuration Utility Programming Guide Revision 3 October 2013 Introduction The following guide will show you the basics of the FSA-CU configuration utility program. The CU can be used with the
More informationProcedure to Create Custom Report to Report on F5 Virtual Services
Procedure to Create Custom Report to Report on F5 Virtual Services Summary: The purpose of this Application Note is to provide a procedure to report on F5 Load Balancer Virtual Services. The report uses
More informationOPERATOR INTERFACE PRODUCTS APPLICATION NOTE
Subject: ST-400 Modbus Master to Schneider Twido PLC when using GP-Pro PBIII AN# 1133 Date: 06/30/2005 Name: Bjorn den Dunnen Page: 1/6 : This application note is an addition to the GP-Pro v7 PLC Connection
More informationNNB Expanse Bridge. User Manual v1.00
NNB Expanse Bridge User Manual v1.00 2 of 6 Revision History: v1.00 Initial Release Neunaber, Expanse, Slate, Echelon, Chroma, and WET are trademarks of Neunaber Technology. Their use in this document
More informationUsing Blackboard Drive to upload/manage content in Blackboard Learn
Using Blackboard Drive to upload/manage content in Blackboard Learn Downloading and Installing Blackboard Drive 1. Login to Blackboard Learn, and click on the Utilities Tab. 2. Locate the Blackboard Drive
More informationDocking Station Operational Description
Docking Station Operational Description August 2018 Copyright 2017, 2018 All Rights Reserved Aures Technologies Changes: Ver 1.0, December 1, 2017, 1 st release Ver 1.1, January 11, 2018, add static IP
More informationHyperBlade Bluetooth Serial Port Setup Guide For use with Scimitar Software and USB Bluetooth adapter Hyperdyne Labs 2006
HyperBlade Bluetooth Serial Port Setup Guide For use with Scimitar Software and USB Bluetooth adapter Hyperdyne Labs 2006 INTRODUCTION If you are using our USB Bluetooth adapter, this document will show
More informationFSU Inventory Scanner Set up & Use for Windows PC
FSU Inventory Scanner Set up & Use for Windows PC FSU Inventory Scanner kit: 1 FSU Property Scanner (Model: CipherLab 8100) 1 Scanner Cradle 1 Scanner Cradle Power Supply 1 USB Cradle to PC Connector Cable
More informationInterpretype Bluetooth Setup Procedure
This information is for configuring the Interpretype to communicate using the Bluetooth Connectivity Kit. To communicate using LAN or Wi-Fi in the full featured version of our software, please refer to
More informationWindows 10 - Starter Guide
Windows 10 - Starter Guide Logging on When the logon screen appears press Ctrl + Alt + Delete then OK. Enter your password then press Enter. Note: Your username does not need to be entered unless switch
More informationD8000 SERIES QUICK START GUIDE
D8000 SERIES QUICK START GUIDE Version 1.0 Overview The D8000 series modules require a DC Voltage power supply, a USB cable and an unused computer USB port for proper operation. Connecting the D8000 series
More informationSerial Bluetooth adapter Setup guide for Windows bit
Serial Bluetooth adapter Setup guide for Windows 8.1 64-bit (Tested in Oracle VM VirtualBox version 4.3.6 r91406) We are in this example using the UCBT232EXA serial Bluetooth adapter and the ES-388 USB
More informationFeatures: Contents: If you are missing any of the above components please contact Racepak at
-------------------------------------------------------------------------------------------- 250-DS-UDX -------------------------------------------------------------------------------------------- Features:
More informationFujitsu SCSI Scanner Installation Procedures Windows 95\98\98SE\ME\2000\XP
If you are installing the following models by means of the SCSI interface then use this document. SP10C M3093GX\DG Fi-4530C Fi-5120C SP15C M3096GX Fi-4640S Fi-5220C SP600C M3097G\G+\DG M4097D Fi-5530C
More informationMigmaWalktime TM for pedestrian detection and walk time extension
SBC Display There are three ways to interfacing with SBC: MigmaMonitor TM, a portable computer monitor with VGA connector and touch screen. This monitor can be left in the controller cabinet. A laptop
More informationUnzip the provided Minix Virtual Machine. This will provide you with the files Minix3.1.8.vdi and Minix LCOM.vbox.
Setting up Minix with Virtualbox Download and install the latest version of VirtualBox from here: https://www.virtualbox.org/wiki/downloads. Download the Minix Virtual Machine here: https://feupload.fe.up.pt/get/jrrtavgkcxf2hy4.
More informationINSTALLING THE PS3 XBOX READY SOFTWARE:
INSTALLING THE PS3 XBOX READY SOFTWARE: 1. Insert the Installation CD to CD-ROM drive and execute Ready_Setup.exe NOTE: If it is the first time for the target USB disk using under this software, the software
More informationUsing Educreations for interactive teaching on ipad
Signing up to Educreations Educreations is an application that is used to create and share video lessons on ipad and web browsers. To sign up, go to http://www.educreations.com/ and click Sign up for free.
More informationMICROSOFT SHAREPOINT SITE OWNER S MANUAL. Creating a Useful, Engaging Site for your Team to Love
MICROSOFT SHAREPOINT SITE OWNER S MANUAL Creating a Useful, Engaging Site for your Team to Love CONTENTS UNDERSTAND SHAREPOINT UNDERSTAND PERMISSIONS CURRENT PERMISSION LEVELS 5 PERMISSION LEVEL DEFINITIONS
More informationInstalling an OptoBlue Adaptor on Windows 8 Operating System:
Installing an OptoBlue Adaptor on Windows 8 Operating System: Before beginning this process, be sure to save all your work in any open programs. Your computer will reboot during this process. Settings
More informationCONFIGURATOR SOFTWARE (S009-50) Quick start guide
P a g e 1 CONFIGURATOR SOFTWARE (S009-50) Quick start guide 1. Download the Configurator Software from our website http://www.mo-vis.com/en/support/downloads 2. Connect the mo-vis Joystick or Multi Swing
More informationVertcoin One-Click Miner (OCM)
Table of Contents Getting Started Finding P2Pool Nodes Hosting P2Pool Node How to Mine Vertcoin One-Click Miner (OCM) Getting Started First off, you'll need to download the OCM. You can find the most recent
More informationIDWedgeBT USB Virtual Serial Port Cable Installation, Configuration and Operation
IDWedgeBT USB Virtual Serial Port Cable Installation, Configuration and Operation Introduction This document explains how to install, configure and use the IDWedgeBT USB Virtual Serial Port Cable to update
More informationCourse Change. 1. Click New Proposal from any tab on the Proposal menu
Course Change 1. Click New Proposal from any tab on the Proposal menu A. If you select a request you can see a summary of the process steps in the fly out menu to the right 1 2. Select the Course Change
More informationUsing the Filter, Field Sets, and Sort Order Menus
Using the Filter, Field Sets, and Sort Order Menus The Filter menu is used to determine the group of records that appear on the page, such as all active students or former students The Field Sets menu
More informationInstalling the Driver
Contents of Package: DWL-520 11Mbps Wireless PCI Adapter Printed Quick Installation Guide CD with Manual and Drivers If any of the above items are missing, please contact your reseller. Installing the
More information12.0 Setting up the PC ready for BESA 11
12.0 Setting up the PC ready for BESA 11 12.1 - Installing Driver. Important Note: Before you start to install the driver, please do not plug BESA 11 into the computer s USB port or else the installation
More informationNERGY SIREN CONFIGURATION. Friday, May 06, 2016 Version 1.02
NERGY SIREN CONFIGURATION Friday, May 06, 2016 Version 1.02 Author Date Version Description SD 7/1/2014 1.00 Original Document JD 7/8/2014 1.01 Changes for public release SD 5/6/2016 1.02 Updates for SoundOff
More informationGetting Started with Outlook Web App (OWA)
Getting Started with Outlook Web App (OWA) Office 365 User Guide When first accessing your new Office 365 account, or if you are having any issues with your regular email client, use the below directions
More informationTech Tips. BeeBots. WeDo
Tech Tips Teachers, especially classroom teachers who are implementing a robotics unit in their classroom, may not have much troubleshooting experience and may not have ready access to tech support. As
More informationAlphaBeam. Description. Requirements. for PC
AlphaBeam for PC Description AlphaBeam is a software application you install on your computer that lets you beam text from your IR-capable AlphaSmart device to an IR-capable computer. AlphaBeam sends text
More informationRTU8 Compact Telemetry Outstation IOTOOL32 PRO Software. Getting Started Guide
1 RTU8 Compact Telemetry Outstation IOTOOL32 PRO Software Getting Started Guide V. 1.00 / Feb 2006 / Doc 40031 2 1. Introduction The RTU8 range of Compact Telemetry Outstations provide an efficient and
More informationUSER GUIDE DOCUMENTATION. Medical Examination Results Transmission System (MERTS) Enhancement MERTS MODULE FOR X-RAY
USER GUIDE DOCUMENTATION Medical Examination Results Transmission System (MERTS) Enhancement MERTS MODULE FOR X-RAY TABLE OF CONTENTS 1 LOGIN... 4 1.1 Login MERTS 3.0... 4 1.2 Logout MERTS 3.0... 5 1.3
More informationGetting Started with ShowingTime for FlexMLS
Getting Started with ShowingTime for FlexMLS ShowingTime is an efficient, online scheduling and management tool which allows you to schedule a showing from any listing in FlexMLS. It enables you to control
More informationWVL2 Wireless Vehicle Link 2 Installation and Setup Manual
WVL2 Wireless Vehicle Link 2 Installation and Setup Manual Chapter 1: Introducing the Wireless Vehicle Link 2...1 WVL2 Components...2 Component Checklist...3 Product Specifications...4 System Requirements...5
More informationTLMC SHORT CLASS: THESIS FORMATTING
Table of Contents Introduction... 2 Getting Help... 2 Tips... 2 Working with Styles... 3 Applying a Style... 3 Creating A New Style... 3 Setting Margins... 4 Adding Page Numbers... 5 Step 1: Using Sections
More informationProjectorNetTM Adapter Quick Start Guide
ProjectorNetTM Adapter Quick Start Guide Adapter networking 1. Quick Start The ProjectorNet Adapter kit contains the following items: ProjectorNet Serial to Ethernet Adapter Cable Adapter, ProjectorNet
More informationPerformer to DP2 Hot Folder Reference Manual Rev There is only one file involved with installing the Performer to DP2 Hot Folder.
Performer to DP2 Hot Folder Reference Manual Rev. 07.11.05 Install Files: There is only one file involved with installing the Performer to DP2 Hot Folder. The installer file is named PP2DP2_1.x.x.EXE.
More informationHVR LINE INSTALL GUIDE
HVR LINE INSTALL GUIDE 4.9.07 HVR v2.4.1 455 E. Industrial Drive P.O. Box 94 Hartland, WI 53029 Technical Support: 262.369.8798 Sales & Service: 262.369.8797 efax: 312.602.1356 www.visioncontrols.net Basic
More informationUser manual. SmartPSS. Manual includes
User manual software is used for viewing, playing back and exporting video footage from IP video surveillance systems. Manual includes Logging In Starting Live View Adding a Custom View Using Digital Zoom
More informationYSC Technologies. YSC USB 2.0 Video Capture and Measurement ToolBox. Tel: USB VideoLink 2.
YSC Technologies YSC USB 2.0 Video Capture and Measurement ToolBox Tel: 510.226.0889 info@ysctech.com www.ysctech.com USB VideoLink 2.0 USB Video Frame Grabber for Microsoft Windows Computers Works with
More informationLab - Task Manager in Windows 8
Lab - Task Manager in Windows 8 Introduction In this lab, you will explore Task Manager and manage processes from within Task Manager. Recommended Equipment The following equipment is required for this
More information