Installation Instructions

Transcription

1 Installation Instructions Fan Kit #00 These instructions outline the procedures to install a Fan Kit in your MMCD-, MMCD-, and MMCD- Jukeboxes with a previously installed owe JUMP Kit. Tools equired / nut driver, drill motor, saber saw, / /, and / drill bits, / open end wrench, and safety glasses. Parts Included with this Kit Item # Part Number Description Quantity 00 Interconnect Circuit oard Assembly 00 Fan 00 Temp Sensor & Harness Assembly 0 Finger Guard #- x ood Screw # x / ood Screw 00 Fan Filter Frame 00 #- x Machine Screw 0 # x / ood Screw 0 00 Fan Filter Screen 000 Filter Pad 000 Fan Mounting Template (MMCD-,,) 0000 Tie rap (Not Shown) 000 These Instructions 0 Figure Page of 0 000

2 . Turn the Jukebox power off, and unplug the power cord from the wall outlet.. Locate the Interconnect Circuit oard Assembly on the back wall above the Computer Core Assembly. Note all of the harness locations on the Interconnect Circuit oard Assembly before disconnecting them. emove the two mounting screws and board, it will not be reused with this application. See Figure. emove this Interconnect circuit board assembly Figure. Using the two screws previously removed, mount the new Interconnect Circuit oard Assembly (Item #) supplied with this kit. econnect all harnesses removed in step. See Figure. econnect harnesses to new Interconnect board Figure Page of 0 000

3 . Dress the harnesses in the fan cutout area with the Tie raps (Item #) provided in this kit. Insure that wiring damage does not occur during the drilling and cutting operation. Cover all components inside the jukebox that are below the fan cut out area with a drop-cloth to protect from sawdust. See Figure. Fan cutout area. Dress Harnesses with tie wraps Cover with drop-cloth below this area Figure Page of 0 000

4 . Loosen the third screw down from the top right rear of the jukebox as shown in Figure.. Attach the Fan Mounting Template (Item #) as shown in Figure ( degree notch up) to the screw loosened in step. Carefully press the template tight against the metal skid rail of the jukebox and tighten the screw. Drill a / pilot hole, then secure the template with a # x / ood Screw (Item #) as shown in Figure.. Drill the three remaining / holes and the six / holes. See Figure.. Scribe or otherwise mark the outline of the fan opening onto the back of the jukebox. emove the template from the jukebox, it will not be reused. Tighten the screw on the right rear side that was loosened in step. NOTE: Do not use the metal template as a guide when cutting the opening for the fan. ight side of jukebox left viewed from the rear. Loosen screw for template Drill two Two / holes Drill two / holes degree notch up Drill / hole and secure template with wood screw Drill one / holes Skid rail Drill four / holes Figure *NOTE: It is very important to cut this opening accurately in the following step, as air leaks will decrease the fans effectiveness.. To cut the fan opening drill /-inch diameter holes to provide blade access (drill as many as needed). Use the saber saw to cut on the inside of the scribed line. emove the drop-cloth used to cover components inside the jukebox. Page of 0 000

5 0. Install the Fan* (Item #) and the Finger Guard (Item #) from inside the jukebox using four #- x ood Screws (Item #). See Figure. Air flow arrow this side Mounting screws two top and two bottom Finger guard Power harness Fan Figure *NOTE: Airflow arrow on the fan must be pointed to the inside of the jukebox.. Assemble the Filter Screen (Item #0) and the Filter Pad (Item #) into the Filter Frame (Item #) and attach with two # x / ood Screws (Item #) as shown in Figure. Finally, to prevent someone from removing the filter frame from the outside, install the four # x x Machine Screws (Item #) from the inside of the jukebox. See Figure. Fan filter frame Filter pad glazed surface outside Filter Screen Two machine screws from inside the jukebox Two wood screws Two machine screws from inside the jukebox Figure Page of 0 000

6 . emove the screw of the Lamp mounting plate on the top panel of the jukebox if present. If not present drill a / pilot hole approximately inches from the left side of the jukebox and inches from the back wall. Install the Temp Sensor and Harness Assembly (Item #) with the plastic spacer against the metal mounting plate or the top panel using the # x / ood Screw (Item #) provided in this kit. See Figure. Note: As the internal jukebox temperature rises the owelink Controller will increase the voltage to the fan. " " Lamp mounting plate. Temp Sensor and Harness Assembly emove this screw from the Lamp Assembly plate. Figure. oute the fan harness down toward the computer core assembly, thru the cable clamps to the P Fan Circuits header on the owelink Controller. Connect the two pin female connector on the fan harness to the two pin male connector of the fan power harness. See Figure. Fan power connection oute the Temp Sensor harness thru cable clamps as shown. owelink Controller P "Fan Circuits Header Page of Figure. Turn the jukebox on and check for proper fan operation.

7 OUTINE SEVICE The air filter will need to be washed periodically. The frequency will depend on the conditions at the site, so it is best to check the filter condition at least once a month. emove and clean the filter as necessary. Use warm water with a mild detergent to clean it. inse thoroughly and allow it to dry. emember that one side of the filter has been glazed to make it easier to slide in and out of the frame. To ease removal and re-installation, this glazed side should face outward. Page of 0 000

8 MMCD-,, iring Diagram + VDC POE D-LINK VDC POE ON/OFF 0 P POE OELINK CONTOLLE 00 S OELINK P D FEMALE > DCDb > DSb > XDb < TSb < TXDb > CTSb < DTb > Ib GND 00 POE ADAPTE STATUS P0 S (quarter) N.C. COM OUTE POE SITCHOX 00 L ELAY + VDC COMMON ESET VDC V COMMON P0 POE OUT KID L TX I CV CDT L TX CC L TX CC L X CONTOLLE LED'S VDC VDC COIN SITCHES COIN ACCEPTO P 00 0 MAS AE-UE ILL ACCEPTO 0 OUTE ESET 000 ESET L P VIDEO SITCH OUTE ESET / VDC VAC 0 0 P P L GOUND 0 0 ON/OFF CTL MUTE NOT OELINK OELINK A VDC V COMMON VDC V COMMON OELINK A OELINK P,,,, J T OELINK X OELINK DISCETE IE Note - A/V CONTOLLE jumper is set to NO ILL ACCEPTO MD ACCEPTO 0 P 0 Y CA- Power Supply CEDIT /ENALE Existing Harness 0 G/Y Existing Harness 0 VAC 0 VAC NC VDC I SIGNAL V COMMON LED ON/OFF NC P J P I DETECTO S COLLECT S POE S CALIATE FAN CICUITS P Y S / L OELINK OELINK A Existing Harness O CA- ILL ACCEPTO OPTIONAL FAN KIT Stripe VDC V COMMON ON/OFF CTL S EJECT SITCHES P COUNTE SEVICE S SEVICE EJECT CALIATE P POE COLLECT POE IN GOUND 00 VDC FAN 00 Temp Sensor Stripe P +VDC V COM VPDC V COM POE IN EJECT P Stripe 0 P.A. OELINK AMP MUTE P 0 CANCEL L O/ NO CONN. NO CONN. P P P 00 P OELINK O/ / 00 from service switch Main Power Supply VOLUME / V /V LOGIC COM + VDC OELINK A P O P Y/ SPLICE Y Y/ Y SPLICE 0 To Price Card & Animation lamps Terminal Strip on Output Transformer Assembly *G/Y 0 ohms watt P COM + VDC O OELINK A OELINK IN +VDC GND Optional egulator Ckt OUT +VDC CA-INTECONNECT 00 or optional 00 shown (used with fan) + VDC P COM ON/OFF CTL 00 P P LOGIC COM / P COM + VDC + VDC Existing -wire Harness that was plugged into CCC P,,, or. P P P 00 POE ELAY ASSY TOUCH PHONO LIGHTS and MONITO ILL ACCEPTO G/Y NEUTAL G/Y GOUND 0 VAC 0 NEUTAL GOUND S'D 0 VAC G/Y Existing Harness. as plugged into Main Power Supply LIGHTS connector. Page of 0 000

9 + VDC POE MOUSE ETHENET COMPUTE POT POT 0 D-LINK -POT MINI-DIN PS KEYOAD 00 ETHENET LEDS J JACK Included with outer 0 IELESS ETHENET OUTE POT 000 AN POT MINI-DIN US Operator Supplied > DCDb > DSb > XDb OELINK + VDC US TO MODEM O NETOK ON-SITE < TSb < TXDb > CTSb < DTb > Ib COM TOUCHSCEEN < DCDa 00** TOUCHSCEEN GND < DSa < XDa D MALE COM > > < > TSa TXDa CTSa DTa < Ia GND MIC IN - YELLO HEADPHONE OUT - LUE J J D MALE SVGA VIDEO ED ETUN D FEMALE SVGA VIDEO INCH FLATPANEL TOUCHSCEEN DISPLAY 00 MONITO ID 0 IN ED GEEN ETUN MONITO ID IN (or DDC data I/O) GEEN AUDIO OUT - GEEN J LUE ETUN H-SYNC LUE NC V-SYNC IEC 0 MALE POE INLET 0 ATX ESET 0 MONITO ID IN (or reserved) SYNC ETUN MONITO ID IN (or DDC clock I/O) SIGNAL GND 0 N L D MALE ** D MALE G N L G Existing MUTE Connector / / 0/ / 0 P MUTE P 00 AUDIO AMPLIFIE 00 ** means included w/monitor or w/core computer 00 V VOLUME Existing Harness /V CONTOL PESS TO 0 ESET EAKE OFF A NEUTAL GOUND 0 VAC G/Y LIGHTS AMPLIFIE 0 LAMP ON TO 0 VAC ALL OUTLET AC PLUG MAIN POE SUPPLY SEVICE Page of 0 000

10 Page 0 of 0 000