Installation Instructions
|
|
- Kerrie Hood
- 5 years ago
- Views:
Transcription
1 Installation Instructions IR REMOTE CONTROL KIT # INTRODUCTION: This kit adds IR Volume and Lighting Control to CD-100L or NSE-1 Jukeboxes that have a 2-Channel Preamplifier TOOLS REQUIRED: 1/4" nut driver PARTS SUPPLIED IN THIS KIT: Part No. Description Qty IR Volume Control #8 x 5/8 Hex WRHS (Type 17) Modular Cable Assy. (2 Ft.) Infra Red Receiver Assy Modular Cable Assy. (15 Ft.) Modular Cable Assy. (4 1/2 Ft.) Circuit Board Support IR Mounting Bracket #8 x 5/8 Hex WRHS (Hi/Lo) Volume/IR 2-Channel Harness Assy IR Transmitter (DL 2-Ch) 1 These Installation Instructions 1 STEP-BY-STEP INSTRUCTIONS: 1. Turn jukebox off and unplug power cord. 2. Install the IR Volume Control (Part # ) in the jukebox on the top shelf, in the area left of the title display board (CD-100L) or Monitor (NSE-1) as shown in Figure 1. Use screws to secure it in the two holes provided, with P1, P2 and P3 towards the front. FIGURE 1 Sht. 1 of 6
2 3. Install the 24" Modular Cable (Part # ) by plugging one end into P5 on the IR Volume Control, routing the cable back, down through the shelf, and forward to the Central Control Computer (CD-100L) or Rowelink Controller (NSE-1). Plug the cable into any one of the ROWELINK jacks, P9 P12 on the CCC (CD-100L) or into P7 on the Rowelink Controller (NSE-1). 4. Mount the IR Receiver (Part # ) which will receive signals from the remote control. You may either place the receiver in the jukebox on the door, or outside and above the jukebox. If placing the IR Receiver outside of the jukebox: CD-100L: Plug one end of the 15' Modular Cable (Part # ) into one of the IR jacks (P5 or P6) on the Keyboard/Display Control circuit board located in the center of the inside of the door, directly behind the user keypad. Route the remainder of the cable right across the door, through the cable clamp and into the jukebox, below the Central Control Computer, down and out the access hole located on the back wall of the jukebox. NSE-1: Plug one end of the 15' Modular Cable (Part # ) into P11 on the Rowelink Controller. Route the cable down and out the access hole located on the back wall of the jukebox. You may need to open the access hole by unscrewing the screws and sliding the cover. Plug the other end of the cable, now outside the jukebox, into the IR Receiver (Part # ). Mount the IR Receiver on the wall or ceiling near the jukebox. If placing the IR Receiver inside the jukebox: Disassemble the IR Receiver (Part # ) to remove the circuit board. Place two plastic circuit board supports (Part # ) on bottom of circuit board and attach to mounting bracket as shown in Figure 2. Plug one end of 54" Modular Cable into P2 of IR Detector circuit board. Maneuver this assembly into top hole on inside center of the door and mount with two screws as shown in Figure 3. Route the rest of the cable around and down to the right, tucking the cable with the other harnesses on the door s edge. CD_100L: About halfway down the door, route the remainder of the cable in towards the keyboard display area and plug into one of the IR jacks (P5 or P6) on the Keyboard/Display Control circuit board. NSE-1: Route the remainder of the cable down the door and in towards the Rowelink Controller along with the door speaker harness. Plug the connector into P11 on the Rowelink Controller. IR Detector Circuit Board IR Mounting Bracket Modular Cable Circuit Board Supports IR Receiver to be Disasssembled FIGURE 2 Sht. 2 of 6
3 Two Screws Tuck Cable with other Harnesses FIGURE 3 5. Locate the volume control wire harness that is connected to the volume control header on the Preamplifier at the top of the back wall of the jukebox. Unplug that harness and reroute it left to the IR Volume Control installed in step 2, plugging it into P3 ( wired volume control ). If the wired volume control is a single volume control (one volume control adjusts both left and right channels): Plug one end of the Volume / IR 2-Channel Harness (Part # ) into the volume control header on the Preamplifier and the other end into the P2 of the IR Volume Control. On the IR Volume Control, set all S1 dip switches to OFF. If the wired volume control is a dual volume control (one volume control adjusts left channel, and another volume control adjusts right channel): Plug one end of the Volume / IR 2-Channel Harness (Part # ) into the volume control header on the Preamplifier and the other end into P1 of the IR Volume Control. On the IR Volume Control, set S1 dip switch 1 to ON and the other switches to OFF. Sht. 3 of 6
4 CONTROLLING THE VOLUME: Volume can be controlled by the IR Transmitter (Part # ) and a single or dual wired (or two single wired) remote control. If a wired control is used to adjust the volume after it has been changed with the IR Transmitter, move the wired control up or down until the volume starts to change, then move it to your desired volume. ON THE IR VOLUME CONTROL BOARD: The ROWELINK RCV LED should flash continuously at approximately 20 CPS. The IR VOL COMM led will flash when a CH1 or CH2 key is pushed. KEYS ON THE IR TRANSMITTER See the following for IR Remote Setup: For the CD-100L refer to the Device Setup Menu in your Service Manual (Vol. I, Section 2) for IR Remote Setup (Keys 9,1). For the NSE-1, see the Jukebox Operations and Setup Screens manual - both of the sections on IR Remote Setup and Credit Management apply. CH1 and CH2, volume UP keys raise the volume. CH1 and CH2, volume DOWN keys lower the volume. POWER key turns lights ON/OFF. When lights are off, the jukebox is in Sleep mode. Any selection currently playing will be cancelled when this mode is entered. In the NSE-1 the monitor also turns off. Pressing POWER again to turn the lights (and monitor in NSE-1) back on will cause the jukebox to resume normal operation and any selections left in the queue when Sleep made was entered will begin to play. LIGHTS + and LIGHTS - For the CD-100L, refer to Section 4 in Volume 2 of your Service Manual, P/N For the NSE-1, refer to Section 4 in your Service Manual, P/N REJECT For the CD-100L, key rejects the song that s playing when pushed and, if enabled, cancels (REJECT ALL) all selections in queue if held down for 5 seconds. For the CD-100L, refer to the Device Setup Menu in your Service Manual (Vol.I, Section 2) for IR Remote Setup IR CLR SEL (Keys 9,1,8). For the NSE-1, see the Jukebox Operations and Setup Screens manual - the section on IR Remote Setup shows the screen used to enable or disable the REJECT and/or REJECT ALL feature. Sht. 4 of 6
5 PAUSE This key puts jukebox in pause mode for a programmed amount of minutes or until the PLAY key is pushed. For the CD-100L, refer to the Device Setup Menu in your Service Manual (Vol. I, Section 2) for IR Remote Setup Remote Pause and Remote Pause Time (Keys 9,1,3 and 9,1,4). For the NSE-1, see the IR REMOTE SETUP section in the Jukebox Operations and Setup Screens manual (P/N ) for menu to setup the PAUSE features. PLAY key puts jukebox in play mode FUTURE key is used to give a remote credit. For the CD-100L, refer to the Device Setup Menu in your Service Manual (Vol. I, Section 2) for IR Remote Setup Remote Credit (Keys 9,1,2) to enable/disable this feature. For the NSE-1, see the CREDIT MANAGEMENT section in the Jukebox Operations and Setup Screens manual (P/N ) for information on setting the daily credit pool. Sht. 5 of 6
6 This page intentionally left blank. Sht. 6 of 6
Kit# KOV ModBox IR REMOTE CONTROL KIT
ModBox Installation Instructions Kit# KOV-106-000-07 ModBox IR REMOTE CONTROL KIT INTRODUCTION: This kit adds IR Volume and Cancel Control to ModBox Jukeboxes. TOOLS REQUIRED: 1/4" nut driver, Philips
More informationRF Remote Control Kit
RF Remote Control Kit The Rock-Ola RF Remote control operates via radio and therefore does not need to see the jukebox or even be in the same room. There are over 1000 channels available for reliable operation.
More informationInstallation Instructions
Second Kit for the GrandSTAR Jukebox Kit #26694913 Purpose: These instructions outline the procedures to install a second 1000W into the GrandSTAR jukebox with the AV controller (shown) or the 4 Channel
More informationCREDIT CARD READER for ROWE CD100I CD100J Jukeboxes Installation Instructions Manual
CREDIT CARD READER for ROWE CD100I CD100J Jukeboxes Installation Instructions Manual Part No. This page intentionally left blank Table of Contents INTRODUCTION...5 Tools Required...5 Credit Card Reader
More informationInstallation Instructions
Kit #67006 - Conversion Kit TT Allegro MX to AMI Tools needed: Philips screw driver, / & 5/6 nut drivers, Drill Driver with / drill bit Parts included in this kit (see page for a picture of the parts in
More informationSeeburg JCU-DEC Kit Convert Your Seeburg DEC Wallbox Into a Jukebox
Seeburg JCU-DEC Kit Convert Your Seeburg DEC Wallbox Into a Jukebox MP3 Compact Flash Player Coin Operated or Free Play Integrated Power Amplifier Line-Out to External Amplifier Programmable Autoplay IR
More informationInstallation Instructions
Installation Instructions NGX Dual Kit Kit #26679601 These instructions outline the procedures to install the Dual Kit in your NGX Jukebox. Tools Required 11/32 Nut Driver Parts Included with this Kit:
More informationInstallation Instructions
Installation Instructions Ecast EQ to AMI hardware conversion KIT #26683701 This kit is for use in Ecast EQ jukeboxes. Tools Required #2 Phillips screw driver, #1 Phillips screw driver, Small flat blade
More informationSection. Service & Maintenance. - Core & Hard Disk Drive (HDD) - Amplifier - Monitor - UPS - Dollar Bill Acceptor - Fan Filter G - 1
Section G Service & Maintenance - Core & Hard Disk Drive (HDD) - Amplifier - Monitor - UPS - Dollar Bill Acceptor - Fan Filter G - 1 Core Removal Core & HDD 1. Open the door. 2. Perform shutdown procedure.
More informationInstallation Instructions
Installation Instructions Kit Core Upgrade-EMB-B75B Without Modem Kit #22166905 These instructions outline the procedures to install the EMB-B75B motherboard into your existing Computer Core Chassis. There
More informationSection. Placing onlocation
Section Placing onlocation -LocationPower -RouterandotherCustomer Premise Equipment(CPE) -ConnectingSpeakers -IRRemoteControl -WiredRemoteControl -PagingMicrophone Floor Model C1-1 Location Power The DA-9000
More informationService & Maintenance
Service & Maintenance Internal Amplifier External (Peavey) Amplifier Core & HDD Monitor UPS Dollar Bill Acceptor Coin Mechanism Cleaning Fans & Filter G1-1 Internal Amplifier Amplifier Removal 1. Disconnect
More informationValidator Update Instructions for Rowe BC1200 $1 - $20
Validator Update Instructions for Rowe BC1200 $1 - $20 Kit Overview The purpose of the kit is to replace the Rowe BA50 transport and stacker with a 120 volt Mars validator with a compact mask. The kit
More informationRoyal RVV-500 (B) Retrofit Kit
Optipay BV/RC/CC into a Non-Fascia Vending Machine This document contains information for installing and configuring the JCM Optipay DBV-01 Bill Validator, RC-10 Bill Recycler and A-66 Coin Changer into
More informationInstallation Instructions. Rock-Ola Ecast B75B Motherboard Upgrade Kit Kit #
Installation Instructions Rock-Ola Ecast B75B Motherboard Upgrade Kit Kit #26683901 This kit will not support the Ecast Rock-Ola COIM Board. If your Rock-Ola core computer has the Ecast Rock-Ola COIM board
More information527F Dual PC Option Installation Guide as replacement for 32MP made by Fadal
527F Dual PC Option Installation Guide as replacement for 32MP made by Fadal Calmotion LLC 21720 Marilla St. Chatsworth, CA 91311 Phone: (818) 357-5826 www.calmotion.com 2006-2013 Calmotion LLC, All rights
More informationAI-102. IR Illuminator. Installation Guide. Rev IP Surveillance
AI-102 IR Illuminator Installation Guide Rev. 1.1 IP Surveillance Revision History: Rev. 1.0: Initial release Rev. 1.1: Changed effective IR range and power consumption. AI-102 Tube Type Infrared Illuminator
More informationInstallation Instructions. Ecast View B75B Motherboard Upgrade Kit Kit #
Ecast View B75B Motherboard Upgrade Kit Kit #26683801 This kit will not support the Ecast View COIM Board. If your View core computer has the Ecast View COIM board installed you must order the AMI Hardware
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS 19 20 21 01 07 22 23 13 10 12 08 17 18 11 02 14 15 04 03 16 WELCOME PARTS LIST Thank you for purchasing this HealthPoint Technology Cabinet from Humanscale! Before you begin installing
More informationInstallation Guide. Retrofit Kit for USB Ready Intraoral Systems
Installation Guide Retrofit Kit for USB Ready Intraoral Systems Table of Contents Wall-Mount Retrofit Kit... 2 Introduction... 2 Connecting the Articulating and Horizontal Arm Cables... 2 Installing the
More informationFLOE WIRELESS REMOTE ASSEMBLY INSTRUCTIONS KIT P/N
FLOE WIRELESS REMOTE ASSEMBLY INSTRUCTIONS KIT P/N 5-0083-00 TOOLS REQUIRED - 3/4" SOCKET - 3/4" WRENCH - /3" WRENCH - PHILLIPS SCREW DRIVER - TORQUE WRENCH INSTRUCTION P/N 6-0083-00 ISSUED: 3//7 SHEET
More informationEASTERN LABS. Instructions Model RM /25/2007. Operation. Junction Box Assembly. Different Types of Switch Installations
EASTERN LABS Instructions Model RM-1205 04/25/2007 Operation Junction Box Assembly Different Types of Switch Installations Counter Mounting Suggestions Operation Total Counter Mix Counter Thru counter
More informationTDM-100/150 TO NMD-50 CONVERSION PROCEDURES RL5000
TDM-00/50 TO NMD-50 CONVERSION PROCEDURES RL5000 TDN 0702-00062 March 7, 204 Corporate Headquarters 2405 B Street Long Beach, MS. 39560 Phone: (800) 259-6672 Fax: (228) 868-9445 COPYRIGHT NOTICE 204 Triton.
More informationE1135C PDU and Pod Upgrade Procedure
E4030-90010 Rev. B 12/2003 In this Document... Tools Needed, 2 Contents of the Upgrade Kits, 2 Installation Procedures, 4 Verifying the Power Option of the New PDU, 4 Removing the PDU from the Support
More informationKit K Instructions. V8700 to Alpha Conversion Instructions
V8700 to Alpha Conversion Instructions Contents Contents Installation Instructions for Kit K-00927-0001 Before You Begin..................................................................................
More information* C29* 68P81084C29-0 RETROFIT INSTRUCTIONS FOR MCS 2000 MOBILE RADIOS. Conversion From Dash/Local Mounting To Remote Mounting
Conversion From Dash/Local Mounting To Remote Mounting RETROFIT INSTRUCTIONS FOR MCS 2000 MOBILE RADIOS Kit Number H634( ) for Model I Radio Kit Number H635( ) for Model II and Model III Radios Introduction
More informationSNOWBOARD RACK KIT P/N APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Instr Rev Page 1 of 25
SNOWBOARD RACK KIT P/N 2881251 APPLICATION Pro Ride RMK 155 and 163, Axys RMK 155, 163, and 174 BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please
More informationRibbon Supply Spindle Maintenance Kit
Installation Instructions This kit includes the parts and documentation necessary to install the Ribbon Supply Spindle Maintenance Kit in the 105SL printer. Read these instructions thoroughly before installing
More informationInstallation and Owner s Manual
Installation and Owner s Manual U.S. and Canada call toll-free: -877-ROC-N-ROL (-877-7-7) Outside the U.S. and Canada, call: () - E-mail: support@amientertainment.net www.amientertainment.net 0 Rev B GrandSTAR
More informationInstallation Instructions. Ecast Mojo B75B Motherboard Upgrade Kit Kit #
Installation Instructions Ecast Mojo B75B Motherboard Upgrade Kit Kit #26684501 This kit contains the parts and instruction to install the B75B Motherboard into your Ecast Mojo jukebox. Tools Required
More informationIon Memory Upgrade. Visit the AMI Entertainment Web site PM
Ion Memory Upgrade Visit the AMI Entertainment Web site http://www.meritgames.com PM0672-04 COPYRIGHT 2011 AMI ENTERTAINMENT NETWORK, INC. Ion Memory Upgrade CONTENTS: QTY PART NUMBER DESCRIPTION 1 EC0146-06
More informationInstallation Instructions
Installation Instructions Tools Required Isopropyl Alcohol Dual DI Box for Applications Parts Included with this Kit KIT #26684202 Item Part Number Description Quantity 1 34109402 Dual DI Box Assy 1 2
More informationTURN-O-MATIC INSTALLATION GUIDE
TURN-O-MATIC INSTALLATION GUIDE WIRELESS SYSTEM WIRELESS SYSTEM (1) Dispenser (1) Dispenser Mounting Bracket (3) Large Slotted Screw (2) Large Slotted Bolt (2) Nut (1) Display Wall Mount Bracket (1) Wireless
More informationCONSOLE CONNECTOR KIT 9501 INSTALLATION INSTRUCTIONS
CONSOLE CONNECTOR KIT 9501 INSTALLATION INSTRUCTIONS FOR USE WITH: HAMMOND Organ Models L-100, M-100 Series, M-l, M-2, M-3 LESLIE Speaker Models 760, 770, 825 KIT CONTENT Console Connector Assembly 043075
More informationINSTRUCTION BULLETIN
INSTRUCTION BULLETIN No. 9008755 Machine: T16 Published: 03-2011 Rev. 00 NOTE: DO NOT DISCARD the Parts List from the Instruction Bulletin. Place the Parts List in the appropriate place in the machine
More informationINSTALLATION MANUAL. LO SIDE BOX ADD-ON KIT For driver or passenger side configurations TRUCK STORAGE SOLUTIONS FOR THE WAY YOU WORK
TRUCK STORAGE SOLUTIONS FOR THE WAY YOU WORK INSTALLATION MANUAL LO SIDE BOX ADD-ON KIT For driver or passenger side configurations Model: QDKSBDO1 -or- QDKSBP01 Part No. 24-0327 Rev. A ECN 5430 ATTENTION:
More informationCourtesy of:discountcarstereo.com. For illustration purposes only BKRCD-HF
Courtesy of:discountcarstereo.com For illustration purposes only BKRCD-HF Hands-Free, Audio Streaming Installation Guide for Becker Radios with CD Changer Created June 30, 2016 Revised: December 26, 2017
More informationCourtesy of:discountcarstereo.com C5CD-HF. Quick Start Bluetooth Installation Guide for select Corvette with 12-Disc CD Changer
Courtesy of:discountcarstereo.com C5CD-HF Quick Start Bluetooth Installation Guide for select 1997-04 Corvette with 12-Disc CD Changer Created January 16, 2013 Revised March 12, 2019 Introduction: If your
More informationMBCD-HF. Quick Start Bluetooth Installation Guide for Select Mercedes with Changer. Courtesy of:discountcarstereo.com
Courtesy of:discountcarstereo.com MBCD-HF Quick Start Bluetooth Installation Guide for Select 1994-98 Mercedes with Changer Created September 3, 2016 Revised: March 24, 2019 Introduction: Safety comes
More informationATTENTION: OBSERVE PRECAUTIONS FOR HANDLING ESD-SENSITIVE DEVICES
Hard Drive Removal IMPORTANT NOTE: If you are replacing a PATA hard drive with a SATA hard drive, please see PATA to SATA Hard Drive Conversion. Hard Drive Identification: To determine whether your hard
More informationCIB 3047 (14B) 10-Button Voice Terminal Fixed Desk Stand and Wall Mount (32007)
CIB 3047 (14B) 10-Button Voice Terminal Fixed Desk Stand and Wall Mount (32007) CIB 3047 Comcode 845-659-325 Issue 1 CIB 3047 (14B) 10-Button Voice Terminal Fixed Desk Stand and Wall Mount (32007) This
More informationATTENTION: OBSERVE PRECAUTIONS FOR HANDLING ESD-SENSITIVE DEVICES
Hard Drive Removal IMPORTANT NOTE: If you are replacing a PATA hard drive with a SATA hard drive, please see PATA to SATA Hard Drive Conversion. Hard Drive Identification: To determine whether your hard
More informationCourtesy of:discountcarstereo.com MB-HF. Hands-Free & Streaming Audio Install Guide for Mercedes
Courtesy of:discountcarstereo.com MB-HF Hands-Free & Streaming Audio Install Guide for 1994-98 Mercedes Created September 3, 2016 Revised: March 23, 2019 Introduction: Safety comes first when you re on
More informationInstructions to Install Retrofit Kit 6/7000 Machine
Instructions to Install Retrofit Kit 6/7000 Machine **TURN POWER OFF OF MACHINE BEFORE INSTALLATION** READ ALL INSTRUCTIONS BEFORE STARTING INSTALLATION Retrofit kit contents: PART NAME QUANTITY PART NUMBER
More informationView Wall Interface. Dynamic Glass INSTALLATION GUIDE. Description. System Requirements. Installation Overview
Description The solution is a compact, wall-mounted interface used for monitoring and changing the tint levels of View Dynamic Glass. The product leverages 802.11-based Wi-Fi technology for connectivity
More informationInstructions to Install Retrofit Kit RVMC 4/5000 Machine (MDB Only)
Instructions to Install Retrofit Kit RVMC 4/5000 Machine (MDB Only) **TURN POWER OFF OF MACHINE BEFORE INSTALLATION** READ ALL INSTRUCTIONS BEFORE STARTING INSTALLATION Retrofit Kit Contents PART NAME
More informationELECTRICAL AND OPERATING CONTROLS
22 1 0V Power Cord 2 6 21 14 19 20 1 230V Power Cord 4 3 P302.50 15 16 9 11 13 10 1 5 P31 P351 DV Models Twins 2 * Indicates the part number listed is OBSOLETE. ^ Indicates the part number listed is for
More informationShuttle Oven Models: S1200, S2000, S2000NC
Shuttle Oven Models: S100, S000, S000NC Need help? Call our hour, toll-free Ovention Hotline Replacement Parts List IMPORTANT NOTE: Locate the Specification Label on the unit to determine the exact Model
More informationPracticeWire Installation Manual
PracticeWire Installation Manual Version 5.0 August 28 th, 2013 PCM Help Desk 1-877-233-9114 Page 1 Table of Contents System Overview 3 Tool List 4 Installation Guide Site Notification 5 Install Universal
More informationVP101-BT Installation Guide
VP101-BT Installation Guide Package Contents 1 VP101-BT system unit 6 Mounting screws for Mini PCIe module 1 Quick Installation Guide 1 Disk includes: - Drivers / Manual Note: The CD that came with the
More informationMacBook Pro 15" Core 2 Duo Models A1226 and A1260 SSD Installation
MacBook Pro 15" Core 2 Duo Models A1226 and A1260 SSD Installation Written By: Dozuki System 2017 guides.crucial.com Page 1 of 10 INTRODUCTION You can install hard drives up to 9.5mm thick. Some drive
More informationDark Energy Survey Detector Head Electronics Crate Disassembly & Modular Replacement Instructions For Type 2 DAQ & Heater Crates
Dark Energy Survey Detector Head Electronics Crate Disassembly & Modular Replacement Instructions For Type 2 DAQ & Heater Crates University of Illinois at Urbana-Champaign Todd Moore Vaidas Simaitis Allison
More informationBL-FLOWSTN-P FlowStation Module Installation Guide
Introduction Baseline s FlowStation is available as an add-on module that is installed inside a pedestal enclosure with a BaseStation 3200 irrigation controller. The FlowStation module comes with a 5-port
More informationGalaxy Rectifier Shelf Field Replacement
Galaxy Rectifier Shelf Field Replacement Model PWRSYS-RFK-A203 Installation Guide Galaxy Rectifier Shelf Field Replacement Model PWRSYS-RFK-A203 Installation Guide, Part Number 139691-1 Copyright 2011,
More informationProRecord and ProScan Installation Procedure for Vertical Pianos With Troubleshooting Guide
ProRecord and ProScan Installation Procedure for Vertical Pianos With Troubleshooting Guide Installation Procedure: 1. Disassemble the piano o Remove the cabinet parts from the piano. o Remove the action
More informationTDM To MiniMech conversion ProceDure
TDM To MiniMech conversion ProceDure (Model 9100 ATM) TDN 07102-00079 Apr 1 2009 CorporATe HeAdquArTers: 522 E. Railroad Street Long Beach, MS 39560 PHONE: (228) 868-1317 FAX: (228) 868-0437 COPYRIGHT
More informationELECTRO-MECH SCOREBOARD CO.
ELECTRO-MECH SCOREBOARD CO. MODEL 2150 SHOT TIMER OWNER S HANDBOOK Thank you for choosing an Electro-Mech Scoreboard for your athletic complex. We are confident that your new shot timer will give many
More informationREMOTE HEAD ADAPTER INSTALLATION GUIDE
REMOTE HEAD ADAPTER INSTALLATION GUIDE The Remote Head adapter is a valuable accessory for the Uniden BC-780, 785 and 796 scanners. It allows the scanner's control panel to be removed from the radio and
More informationCourtesy of:discountcarstereo.com USB-C5. Quick Start Installation Guide for Select Corvette
Courtesy of:discountcarstereo.com USB-C5 Quick Start Installation Guide for Select 1997-04 Corvette Created January 16, 2013 Revised October 24, 2018 Introduction: Just because you drive an older car does
More informationReplacing the Galaxy II CRT Monitor with a Flat Screen Monitor Kit # 42638
Replacing the Galaxy II CRT Monitor with a Flat Screen Monitor Kit # 42638 This kit contains detailed instructions on removing a Galaxy II Daewoo monitor and replacing it with a 19 wide flat screen monitor.
More informationTile Plow Installation O Connell
NOTE: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number Quantity Tile Plow Kit O Connell System 4100471 1 Hex head cap screw 3/8-16 x 3 2002003-38300
More informationCAVS USA Inc. Quick Start Manual For Karaoke Jukebox CAVS JB-99RX. Version and up
Quick Start Manual For Karaoke Jukebox CAVS JB-99RX Version 1.0.0.261 and up 1 Contents Page 1. Unpacking 3 2. Installation 4 2.1 Touch Screen monitor 4 2.2 Mixer-Amplifier 5 2.3 Microphone 5 3. Booting
More informationKramer Electronics, Ltd. USER MANUAL. Model: VS-1616A. 16x16 Balanced Stereo Audio Matrix Switcher
Kramer Electronics, Ltd. USER MANUAL Model: VS-1616A 16x16 Balanced Stereo Audio Matrix Switcher Contents Contents 1 Introduction 1 2 Getting Started 1 3 Overview 2 4 Your Balanced Stereo Audio Matrix
More informationSecured Series: Hub Plus Kit Single Door Controller Package Installation Manual
Secured Series: Hub Plus Kit Single Door Controller Package Installation Manual This package is designed to simplify the connections to our Secured Series Hub Plus Controller. This will translate into
More informationATTENTION: OBSERVE PRECAUTIONS FOR HANDLING ESD-SENSITIVE DEVICES
1. Turn off and unplug the game. COPYRIGHT 2007 MERIT ENTERTAINMENT 2. Unlock and open the CPU section. Ion evo/evo Wallette/Elite Edge ECS Motherboard Removal 3. Remove the 3 screws securing the I/O board
More informationInstalling a Power over Ethernet injector
Installing a Power over Ethernet injector AlphaEclipse StreetSmart and RoadStar signs The instructions in this document explain how to install/replace a Power over Ethernet (PoE) injector in a StreetSmart
More informationE2460GS Oscilloscope Upgrade Kit
Installation Instructions for E2460GS Oscilloscope Upgrade Kit Agilent 1670G-Series Logic Analyzers This kit upgrades either the Agilent Technologies 1670G, Agilent 1671G, Agilent 1672G, or the Agilent
More informationStar Trac Fitness E-ST 5090 Stepper. Install Guide
Star Trac Fitness E-ST 5090 Stepper Install Guide STAR TRAC E-ST STEPPER Install Guide E-ST 5090 E Series Stepper ASSEMBLY AND SETUP The following parts are included with the base STAR TRAC E-ST STEPPER:
More informationGM3x-HF Installation Guide for GM Class II Radios with XM Tuner
Courtesy of:discountcarstereo.com Driving without distraction is a necessity for a safer driving experience GM3x-HF Installation Guide for GM Class II Radios with XM Tuner Created July 19, 2016 Revised:
More informationSony NEX-7 Screen Replacement
Sony NEX-7 Screen Replacement If your camera's screen is broken or non functioning, this guide will show you how you can replace the screen. Written By: Jay Miley ifixit CC BY-NC-SA www.ifixit.com Page
More informationZ Series and S4M Ribbon Take-Up Spindle Maintenance Kit
Z Series and SM Installation Instructions This kit includes the parts and documentation necessary to install the Ribbon Take-Up Spindle Maintenance Kit into the following printers: Z Series (ZM, Z6M, ZMplus,
More informationRack Installation Instructions
Rack Installation Instructions Review the documentation that comes with your rack cabinet for safety and cabling information. When installing your server in a rack cabinet, consider the following: v Two
More informationLab 4: Trajectory Following 1
Lab 4: Trajectory Following 1 Prelab Familiarize yourself with how the LabVIEW program works It is XYposition_control1.4.vi Located in Lab4_LabVIEW.zip on the Stellar page 2 Optional prelab: create your
More informationPhase Loss Protection Upgrade. Phase Loss Protection Upgrade. In this bulletin:
Phase Loss Protection Upgrade In this bulletin: Introduction... 2 Purpose... 2 General... 2 Applicability... 2 HD3070 Phase Loss Protection Upgrade Kit Parts... 2 Preparation... 4 Install the Phase Loss
More informationThe CD100MP3 is a micro-computer based hard disk player that replaces the entire CD mechanism and decoder in your ROWE/AMI CD100 jukebox.
The CD100MP3 is a micro-computer based hard disk player that replaces the entire CD mechanism and decoder in your ROWE/AMI CD100 jukebox. The hard disk player works with any jukebox that uses the 408322xx
More informationZ Series and S4M Ribbon/Head Open Sensor Assembly
Z Series and S4M Installation Instructions This kit includes the parts and documentation necessary to install the ribbon/head open sensor assembly into the following printers: Z Series (Z4M, Z6M, Z4Mplus,
More informationSERVICE MANUAL MODEL SSW-521-D2-ADA
SSW-521-D2-ADA-SPK1.07UNVLr3-ADA-ISSUE4.0 SERVICE MANUAL FOR MODEL SSW-521-D2-ADA STAINLESS STEEL HANDS FREE WALL TELEPHONE WITH OPTIONAL ADA FEATURE AND OPTIONAL SECOND-NUMBER AUTO-DIAL FEATURE EQUIPPED
More informationCIB 2924 Line-Powered Alert Ringer and Parts
CIB 2924 Line-Powered Alert Ringer and Parts CIB 2924 Comcode 103-974-697 Issue 1 CIB 2924 Line-Powered Alert Ringer and Parts The D181233 Line-Powered Alert Ringer and Parts (see Figure 1) consists of
More informationQuick start guide for i5 520 ( or )
Quick start guide for i5 520 (9405-520 or 9406-520) 1 Before you begin This Quick start guide contains an abbreviated set of setup instructions designed to help you quickly unpack and set up a standard
More informationETERNUS DX80 S2 and DX90 S2. Hardware Installation
Content Package Contents Rack Mounting Power Cabling Backend Cabling QSFP Power On Procedure Power Off Procedures Operator Panel - Function Button 1 Package Contents (1) Controller Enclosure Kit Installation
More informationPeel/Rewind Upgrade Kit
Peel/Rewind Upgrade Kit Installation Instructions This kit includes the parts and documentation necessary to install the Peel/Rewind upgrade kit on the following printers: ZM400 ZM600 Read these instructions
More informationCAMERA ASSEMBLY. Removal/Replacement of the Camera Box Assembly APR-CA. Install Camera Assembly. Remove Camera Assembly
CAMERA ASSEMBLY Removal/Replacement of the Camera Box Assembly APR-CA REQUIRED TOOLS: 9/64 hex key Small flat-tip screwdriver Remove Camera Assembly camera 1. Locate the camera assembly underneath the
More informationABM International, Inc. Lightning Stitch Checklist 9/13/2013
ABM International, Inc. Lightning Stitch Checklist 9/13/2013 1) Piggy backed board assembly (1) Piggy back board assembly tested? Yes No 24v passed XB passed XA passed YB passed YA passed SAFE passed S/S
More informationPCS-2. Universal Infrared Remote PC Power Switch
PCS-2 Universal Infrared Remote PC Power Switch General Description The PCS-2 allows you to switch your PC / HTPC on-off with your existing TV or universal infrared (IR) remote. Single button mode allows
More informationElectronics. Plate 1.1 MPD -1 Computer Display Module Three-Grade, Four-Grade, and Fixed Blender F F
Plate. MPD - Computer Display Module Three-Grade, Four-Grade, and Fixed Blender 3 5 2 2 3 F 5 6 F2 7 8 9 0 7 6 8 9 7 0 5 3 6 2 8 Page 0 PT-80 MPD Series Illustrated Parts Manual /93 Housing, Black T6037-G2S6
More information1. Mount the echo and tremolo control switches under the keyboard shelf, in a position convenient for the organist.
CONSOLE CONNECTOR KIT 8101 INSTALLATION INSTRUCTIONS FOR USE WITH: HAMMOND Organ Models A-100, D-100, RT2, RT3 LESLIE Speaker Models 122, 122RV KIT CONTENT Console Connector Assembly 047357 Echo Control
More informationQuick start guide Speakerphone/ answering system with caller ID/call waiting
Quick start guide 1856 Speakerphone/ answering system with caller ID/call waiting Quick reference guide FLASH During a call, press to receive an incoming call if call waiting is activated. DISPLAY DIAL
More informationTile Plow Installation Gold Digger
NOTE: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number Quantity Tile Plow Kit Soil Max System 4100470 1 Hex head cap screw - M10 x 75mm 2002007-10075
More informationReplacing the PanelMate Power Pro 1785 Series, PanelMate epro 7585x-8 and 7685x-8 Series Backlight Assembly
Replacing the PanelMate Power Pro 1785 Series, PanelMate epro 7585x-8 and 7685x-8 Series Assembly Introduction The Replacement Kit provides a replacement backlight for the PanelMate Power Pro 1785 Series,
More informationAmano (itrt) Intelligent Twin Reader Terminal INSTALLATION MANUAL
MODEL NUMBER: XRT910-0-0-AC-XX XRT920-0-0-AC-XX AMANO itrt Amano (itrt) Intelligent Twin Reader Terminal INSTALLATION MANUAL SPECIFICATIONS Working Environment Plastic Housing... Power Designed to work
More informationKramer Electronics, Ltd. USER MANUAL. Model: VS-162V. 16x16 Video Matrix Switcher
Kramer Electronics, Ltd. USER MANUAL Model: VS-162V 16x16 Video Matrix Switcher Contents Contents 1 Introduction 1 2 Getting Started 1 2.1 Quick Start 1 3 Overview 3 4 Your Video Matrix Switcher 4 4.1
More informationCU-8R Installation Instructions
CU-8R Installation Instructions I. Components Model CU-8R is shipped with the following components: QTY Item 1 Stainless Steel Enclosure 2 Lexan Panels 18 Nuts 1 Wall Mount Style Phone with RJ-11 Cable
More informationConnecting a Cisco Input Module
CHAPTER 4 Overview The optional Cisco Input Module (Figure 4-1) is attached to a Cisco Physical Access Gateway or Cisco Reader Module to provide additional connections for up to ten input devices. Each
More informationUser s manual. ML17929 Two-line corded telephone with caller ID/call waiting
User s manual ML17929 Two-line corded telephone with caller ID/call waiting Congratulations on purchasing your new AT&T product. Before using this AT&T product, please read Important safety information
More informationInstallation Instructions
Installation Instructions HCLK8SS Network Clock Programming Mode Installation and Operation The HCLK8SS Network Clock can be converted to a hand-held Dataline Switch Programmer with the flip of a switch.
More informationArtisan Technology Group is your source for quality new and certified-used/pre-owned equipment
Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment FAST SHIPPING AND DELIVERY TENS OF THOUSANDS OF IN-STOCK ITEMS EQUIPMENT DEMOS HUNDREDS OF MANUFACTURERS SUPPORTED
More informationWritten By: John Sutton
Replacing the fan on your HP g7-2275 dx. Written By: John Sutton ifixit CC BY-NC-SA www.ifixit.com Page 1 of 20 INTRODUCTION Laptop cooking your lap? This guide will walk you through replacing your fan.
More informationUSER MANUAL FEATURES
USER MANUAL FEATURES Hands-free dialing with Indicator Headset operation with Indicator Automatic headset / handset mode detection Headset / Handset operation Headset transmitter / receiver volume control
More information9600 PCI EPP Keypad and
9600 PCI EPP Keypad and Card Reader Upgrade TDN 07103-08200 Feb 11, 2011 This upgrade requires software updates for both Canada and the US. Refer to page 6 in this manual and the Triton web site for the
More information16Hi HARDWARE INSTALLATION GUIDE
16Hi HRDWRE INSTLLTION GUIDE Table of Contents Section 1 Ratings....................................................................... 3 Section 2 Site Preparation................................................................
More information