Signature 384 Upsampler and USB input Users Manual
|
|
- Amos Nicholas Ray
- 5 years ago
- Views:
Transcription
1 Signature 384 Upsampler and USB input Users Manual Rev 1 (4/09)
2 Signature 384 Upsampler Installation Procedure: 1) Remove one Side Panel (End Cap) by removing 4 Allen Screws as shown. 2) Remove 6 Philips screws from top and bottom of cover. Remove cover, and disconnect ribbon cable that attaches the Front Display to the Platinum Main Board. Reference CD Players will have more than one ribbon cable; both will have to be removed. Set cover, Screws and End cap aside. 3) Remove old Input Board, and install your new Signature Board. Be sure to properly align the board so the pins of the board are properly mated to the socket on the Main Board. Depending on your Platinum, there may be extra pins on the Board. This is OK. 4) Locate the Revision Number of the Platinum Main Board. If your Board Revision is 6.4 or above, you may skip the rest of this installation and proceed to the Operation section of this manual. For Revisions less than 6.0 you MAY be finished or if you experience unexpected shutdown when hot you will need to make this power supply change. Input Board For Revision 6.0 to 6.3 you need to make a change to the power supply. You will need a sharp knife, a soldering iron and a piece of wire. 5) The final step has to do with upgrading the firmware in the digital filter. A custom audio file is supplied with your upgrade which must be played by the DAC once the new board is installed. This code is keyed to the serial number of your DAC and Signature Digital Filter if you have one. Both serial numbers must be supplied to MSB to make this file. For this upgrade to work, the DAC must have either a 16x or 32x Digital Filter. Play the update file and listen to the file play. It contains instructions on how to confirm a successful update. 2
3 The USB Option Installation The USB input installation requires no more than drilling a hole in the back cover. It is quite thick steel and this task should not be attempted without proper tools and skills. MSB does not consider this a customer installable upgrade. The DAC should be returned to MSB or taken to a qualified technician. Place template on back, align with top and right edge. Drill pilot hole and then larger hole. Check with actual connector before drilling mounting holes. Attach with screws and nuts provided. Mark out edge of PCB and trim. Reinstall mother board in DAC. Plug in Upsampling board and USB cable.
4 OPERATION - UPSAMPLING The operation is simple. The front panel switch labelled either upsampling or DAC option will switch the upsampling on and off. The display will show the upsampled frequency. This upgrade also allows the SPDIF and MSB Network inputs to accept 384 khz x 32 bit signals. Dip switch 1: ON = Reclocking on, OFF = Reclocking off (no delay) Dip switch 2: ON = Alternate Upsampling algorithm, OFF = Preferred upsampling OPERATION - USB Input Plug a USB cable into your computer. The USB input is now positioned between MSB 1 and MSB 2 as far as the priority input switching is concerned. To manually select the USB input, SELECT MSB 2 Input and remove any MSB device from MSB2.
5 MAC Operation Select SOUND from the PREFERENCES page. The MBS DAC will show up under the OUTPUT tab. Click and close window. That is all you need to do to make the USB your audio output. Output Sample Rates Unfortunately OSX is smart and converts all music played on a MAC to the sample rate you select, rather than its native resolution. This seriously hurts audio quality, especially when the output is not a multiple of the input. (Outputing 48k when playing CDs at 44.1k). Go to the UTILITIES folder and select AUDIO MIDI SETUP. You may select the output format for your MAC. Set it to the native format of the music you wish to play.
6 WINDOWS VISTA The USB output is automatically activiated when plugged in. You should hear audio immediately. Unfortunately Vista is smart and converts all music played on a PC to the sample rate you select, rather than its native resolution. This seriously hurts audio quality, especially when the output is not a multiple of the input. (Outputting 48k when playing CDs at 44.1k). You can set the output format in the control panel as shown below. W I N D O W S XP XP seems to behave d i f f e r e n t l y on different computers. On some it outputs any filed played in its native resolution. On others it does not. These windows show how to select the MSB output.
Upsampling Upgrade for the LINK DAC III Rev #7 (3/2006) Users Manual
Upsampling Upgrade for the LINK DAC III Rev #7 (3/2006) Users Manual Thank you for purchasing the Upsampling Upgrade for your LINK DAC. I am sure you will be very pleased with it. It adds the following
More informationNetwork Upgrade for the LINK DAC III
Network Upgrade for the LINK DAC III Rev #3 (6/2001) Users Manual Thank you for purchasing the Network Upgrade for your LINK DAC. I am sure you will be very pleased with it. It adds the following new features
More informationPhase Loss Protection Upgrade. Phase Loss Protection Upgrade. In this bulletin:
Phase Loss Protection Upgrade In this bulletin: Introduction... 2 Purpose... 2 General... 2 Applicability... 2 HD3070 Phase Loss Protection Upgrade Kit Parts... 2 Preparation... 4 Install the Phase Loss
More informationCourtesy of:discountcarstereo.com USB-JAG. Quick install Guide for Jaguar X100 and X308 with Changer
Courtesy of:discountcarstereo.com USB-JAG Quick install Guide for Jaguar X100 and X308 with Changer Created: September 10, 2016 Revised: May 31, 2018 Introduction: Just because you drive an older car does
More informationFC-25/50DA Main Circuit Board Replacement Product Installation Document
FC-25/50DA Main Circuit Board Replacement Product Installation Document Document 51875 Rev A 10/12/01 ECN 01-506 This Product Installation Document outlines the replacement of the Main Circuit Board for
More informationFITTING INSTRUCTIONS
& This option connects a GL3000 or GL3300 console as a channel expander to a second console with just one or two interconnecting cables. Kit Part No: GL3000-SL1 Single option to install SYS-LINK to one
More informationQuicksilver 606 TR-606 CPU Upgrade
Quicksilver 606 TR-606 CPU Upgrade D650C 128 Installation Guide Social Entropy Electronic Music Instruments TABLE OF CONTENTS WARNINGS... 1 OVERVIEW... 2 WHAT'S IN THE BOX... 3 OPENING THE TR-606 CASE...
More informationCourtesy of:discountcarstereo.com JAG-CDR. x308 with CD Changer. Created May 3, 2016 Revised: July 4, 2017
Courtesy of:discountcarstereo.com JAG-CDR Quick Start Installation Guide for Jaguar x100 & x308 with CD Changer 2000-03 03 x308 and 2000-06 06 x100 Premium Systems Created May 3, 2016 Revised: July 4,
More informationEmax SE SCSI Port Emax Plus Retrofit Instructions (Fl360)
Emax SE SCSI Port Emax Plus Retrofit Instructions (Fl360) Tools needed: Exacto Knife, Vacuum Desoldering Tool, Soldering Iron, Solder, Phillips Screwdriver, Needle Nose Pliers, 1/2 Nut Driver, 5/8 and
More informationAssembly Guide. LEDs. With these assembly instructions, you can easily build your own SWT16. All required components are included in this kit.
Assembly Guide With these assembly instructions, you can easily build your own SWT16. All required components are included in this kit. You need the following tools: soldering iron, wire cutter and solder.
More informationVoice Evacuation Control Panel Main Circuit Board Replacement Product Installation Document
Voice Evacuation Control Panel Main Circuit Board Replacement Product Installation Document Document 50795 Rev B 10/10/01 ECN 01-507 This Product Installation Document outlines the replacement of the Main
More informationEMC 10/4 "CE" Mechanical Upgrade Procedure
EMC 10/4 "CE" Mechanical Upgrade Procedure Kit Part Number: 009663-01 This procedure upgrades a non-ce compliant machine to the mechanical requirements of a CE compliant machine. Properly upgraded machines
More informationMusic Technologies Group. MTG Pro One TurboCPU CV (DAC) Installation Guide
Music Technologies Group MTG Pro One TurboCPU CV (DAC) Installation Guide Version 1.41 (Beta) November 2015 CONTENTS 1: Introduction... 3 Precautions!... 3 2: Installation... 4 Tools and Parts Required
More informationSingle cable kit for the FCB1010
Single cable kit for the FCB1010 1. What is it? With this kit, you can turn your FCB1010 into a phantom powered floorboard, which can do 2-way MIDI communication over one single cable. After installing
More informationHARMONi G3. Quick Start Guide for HARMONi G3. imac Processor/FireWire Upgrade
HARMONi G3 imac Processor/FireWire Upgrade imac and Operating System Compatibility The HARMONi G3 imac processor/firewire upgrade is compatible only with imac 233, 266, and 333 MHz models (Revisions A-D);
More informationUSB board Mk2 INSTRUCTION MANUAL
USB board Mk2 INSTRUCTION MANUAL Revision 0, December 2017 This manual comprises introducing information on use and performance of this device. For more information please refer to the Audial web site,
More informationCourtesy of:discountcarstereo.com USB-C5. Quick Start Installation Guide for Select Corvette
Courtesy of:discountcarstereo.com USB-C5 Quick Start Installation Guide for Select 1997-04 Corvette Created January 16, 2013 Revised October 24, 2018 Introduction: Just because you drive an older car does
More informationAn ISO 9001 Company. BOP 1KW-MG FIRMWARE RETROFIT KIT
INSTRUCTION MANUAL 1. DESCRIPTION KEPCO An ISO 9001 Company. BOP 1KW-MG FIRMWARE RETROFIT KIT BOP 1KW-MG RETROFIT KIT 219-0621 Kepco KIT 219-0621-(n) contains the parts used to upgrade the firmware for
More informationSteps to test Windows Audio
Steps to test Windows Audio Step 1: Testing for an audio signal Use this process to find out if Windows can detect an audio signal from the microphone or from the line-in port. NOTE:If you are testing
More informationMIDI IN Installation Guide for the EMU Drumulator
MIDI IN Installation Guide for the EMU Drumulator 1 WARNING: This installation process is the user s responsibility and shall be followed at their own risk! To complete this modification the procedure
More informationInstalling TEAC CD-ROM Drives
D I G I T A L Installing TEAC CD-ROM Drives S O U N D Date: May 12, 2000 (updated) Document # TN-E211 We have used only two manufacturers of CD-ROM drives: Toshiba and TEAC. This procedure is to be used
More informationDigital Media Player Installation Instructions
Description Phat Noise Digital Media Player Installation Instructions Part Number 000 057 110 Fitment Description Application Passat Sedan/Wagon 98> Supplier PhatNoise Revision 1 Published date: 06-23-03
More informationOff-Ramp 4 User Manual Empirical Audio Rev. 1.0
Off-Ramp 5 User Manual Empirical Audio Rev. 2.0 2012 Off-Ramp 4 User Manual Empirical Audio Rev. 1.0 1. Function/Technology The Off-Ramp 5 is a versatile hi-res compatible USB interface. The function of
More informationComputer Audio Setup Guide
Computer Audio Setup Guide This guide is intended to be used as a quick reference tool for those embarking on their journey into the world of Computer Audio. While there is always more to discuss and discover,
More informationFilm-Tech. The information contained in this Adobe Acrobat pdf file is provided at your own risk and good judgment.
Film-Tech The information contained in this Adobe Acrobat pdf file is provided at your own risk and good judgment. These manuals are designed to facilitate the exchange of information related to cinema
More informationA Backlighted LCD for your K1
A Backlighted LCD for your K1 (K1BKLTKIT) Tom Hammond - NØSS, July 27, 2006 Rev C Thanks to Wayne Burdick, N6KR for suggesting this implementation of backlighting the K1 display. APPLICABILITY This modification
More informationMounting on the Ceiling Using Flush Mount (Face Down)
Mounting on the Ceiling Using Flush Mount (Face Down) Installation Guide 2014/02/14 Table of Contents Safety Information... 3 Installation Procedures... 5 Step 1: Drill a Hole on the Ceiling... 5 Step
More informationANIxx. Installation Manual.
ANIxx Installation Manual www.audac.eu Introduction WaveDynamics Dante audio network interface The ANIxx are Dante audio network interfaces for use with WaveDynamics supporting amplifiers, supporting two
More informationRECOMMENDED TOOLS PERSONAL & VEHICLE PROTECTION MASKING TAPE
GUIDE PART NUMBER: 250-7616 GM SOFT TOUCH NAVIGATION SYSTEM GENERAL APPLICABILITY 2013- RAV4 KIT CONTENTS ITEM QTY DESCRIPTION 1 1 NAVIGATION INTERFACE MODULE 2 1 VEHICLE INTERFACE T-HARNESS 3 1 LCD/GPS
More informationThe basic product comes with the IRS5 control board, 3 internal cables, 1 external cable with a 5 volt adapter and a mounting bracket with hardware.
Please read these instructions and watch the Installation Video before you proceed with the installation of the PC-IRS5-01. Installation Video: http://youtu.be/os98e32vhb4 The PC-IRS5-01 Infrared Receiver
More informationCygnos360 V2 Installation Manual
VERSION 1.0. - OKTOBER, 2009 www.cygnos360.com Contents: 1. What you need...2 1.1. Tools...2 2. Preparation...3 2.1. Preparing the solder points...3 3. Installing in your Xbox360...4 3.1. Installing the
More informationENCORE /ST G4 DUET. Dual Processor Upgrade Card for Power Mac G4 AGP Graphics. Quick Start Guide for Encore/ST G4 Duet
ENCORE /ST G4 DUET Dual Processor Upgrade Card for Power Mac G4 AGP Graphics Quick Start Guide for Encore/ST G4 Duet Power Mac and Operating System Compatibility This Encore/ST G4 Duet processor upgrade
More informationEMC 10T "CE" Mechanical Upgrade Procedure
EMC 10T "CE" Mechanical Upgrade Procedure Kit Part Number: 009866-01 This procedure upgrades a non-ce compliant machine to the mechanical requirements of a CE compliant machine. Properly upgraded machines
More informationMytek Protools-HDX DIO Card User's Manual. Mytek Protools HDX DIO Card. User's Manual. ver. 2.0 / Nov 2013
Mytek Protools HDX DIO Card User's Manual ver. 2.0 / Nov 2013 Mytek 2013 This manual may be updated at any time. To download the latest version, technical support, and for setup tips please visit: http://www.mytekdigital.com
More informationCasio CZ. Non volatile memory modification Installation instructions version copyright 2013 Artefacts
Casio CZ Non volatile memory modification Installation instructions version 2.0 2017 www.artefacts.nl copyright 2013 Artefacts Introduction The Casio CZ-101 and CZ-1000 do not have a separate backup battery
More informationCRESCENDO /PB G3. Processor Upgrade Card for Macintosh PowerBook 1400 Series Computers. Quick Start Guide for Crescendo/PB G3
CRESCENDO /PB G3 Processor Upgrade Card for Macintosh PowerBook 1400 Series Computers G3 Macintosh PowerBook and Operating System Compatibility The Crescendo/PB G3 processor upgrade card is compatible
More informationQuick Start Guide ONLY for Encore/ST G4 Duet 1.8 GHz
Quick Start Guide ONLY for Encore/ST G4 Duet 1.8 GHz Power Mac and Operating System Compatibility This Encore/ST G4 Duet processor upgrade card is compatible only with Power Mac G4 AGP Graphics, Gigabit
More informationQuick Start Guide ONLY for Encore/ST G4 Duet 1.8 GHz
Quick Start Guide ONLY for Encore/ST G4 Duet 1.8 GHz Power Mac and Operating System Compatibility This Encore/ST G4 Duet processor upgrade card is compatible only with Power Mac G4 AGP Graphics, Gigabit
More informationINSTRUCTIONS FOR USE Pro-Ject DAC Box S USB
INSTRUCTIONS FOR USE Pro-Ject DAC Box S USB Dear music lover, thank you for purchasing a PRO-JECT AUDIO DAC Box S USB. In order to achieve maximum performance and reliability you should study these instructions
More informationRSL PSM-2 Power Supply Module Project: Modifying a FlatCap2
RSL PSM-2 Power Supply Module Project: Modifying a FlatCap2 Dear Do-It-Yourselfer, The stock FlatCap2 is less than a stellar performer. Used with a CD5 CD player, for example, it gives flabby bass control,
More informationMicroprocessor Module Replacement Kit for Multi-Zone Leak Monitors Instruction Manual
621 Hunt Valley Circle New Kensington, PA 15068 3015-5547 Tel: 724-334-5000 Revision 4 Fax: 724-334-5001 May 17, 2013 Microprocessor Module Replacement Kit for Multi-Zone Leak Monitors Instruction Manual
More informationMACRO MODCHIP FOR XBOX360 CG2 INSTALLATION INSTRUCTIONS
MACRO MODCHIP FOR XBOX360 CG2 INSTALLATION INSTRUCTIONS List of tools and materials needed: Modchip, flexible LED add-on board, 6 tac switches Microsoft wireless CG2 controller Soldering iron and thin
More informationPU-160ETH. Ethernet and USB to HDMI Converter. Operation Manual PU-160ETH
PU-160ETH Ethernet and USB to HDMI Converter Operation Manual PU-160ETH Trademark Acknowledgments All products or service names mentioned in this document may be trademarks of the companies with which
More informationENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA Welcome Before You Begin Thank you for choosing a Marantz CD player. This guide provides
Model SA-KI RUBY Quick Start Guide Super Audio CD Player ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA Welcome Before You Begin Thank you for choosing a Marantz CD player. This guide provides
More informationUSB and DSD Setup Guide. Audiolab USB and DSD Setup Guide :29:24
Audiolab USB and DSD Setup Guide1 1 2015-12-22 16:29:24 Installation of Audiolab for Asynchronous mode (Audiolab USB Driver - IAG Platform) Setup of Operating System 1 Mac OS X 2 Windows 8 / Windows 7
More informationRemoval and Replacement of the Serrano and Corsica Boards
Removal and Replacement of the Serrano and Corsica Boards 1. Purpose The purpose of this procedure is to document the removal and replacement of the Serrano and Corsica board of the Deko/Thunder Assemblies.
More informationBehringerMods.com. Instructions for modification of Behringer SRC analog inputs and outputs
BehringerMods.com Instructions for modification of Behringer SRC analog inputs and outputs The following instructions will cover the details of fully modifying a unit with analog output and analog input
More informationM-570 USB 4-CH Wireless. Sound Box
M-570 USB 4-CH Wireless Sound Box User Manual Ver. 1.00 All brand names and trademarks are properties of their respective owners. Contents: Chapter 1: Introduction... 3 1.1 Product Introduction... 3 1.2
More informationHow to hardwire the Olympus D-370 and D-380 Digital Cameras
How to hardwire the Olympus D-370 and D-380 Digital Cameras Copyright, PixController http://www.pixcontroller.com, all rights reserved. This document covers in detail how to modify either the Olympus D-370
More informationS4M 10/100 Internal ZebraNet PrintServer, Wireless Print Server, Parallel Port, and No Comm Option Kits
S4M 0/00 Internal ZebraNet PrintServer, Wireless Print Server, Parallel Port, and No Comm Option Kits Installation Instructions This kit includes the parts and documentation necessary to install the 0/00
More informationQuick Start for DATS on Windows 7
Skip directly to the section that covers your version of Windows (7, Vista or XP) Quick Start for DATS on Windows 7 *** VERY IMPORTANT SAFETY NOTE *** NEVER connect the test leads of the DATS to a speaker
More informationCustom O2+ODAC Soldering Instructions
Custom O2+ODAC Soldering Instructions Preparations The following components should be omitted during basic assembly: R1, R2 D2, D6 BT2 The following components should be omitted based on required customization:
More informationReference Quality 24bit upsampling D/A Converter
NJC Audio Web: www.njc-audio.co.uk E-Mail: sales@njc-audio.co.uk Quality Hand Built Amplifiers, DACs & Interconnects... (Mark II) Reference Series - 24bit DAC Reference Quality 24bit upsampling D/A Converter
More informationX3M. ExcelValley. MIDI + USB Sound Module: Supports hardware wavetable synthesis + audio. playback, multifunctional MIDI DIN connector.
ExcelValley X3M MIDI + USB Sound Module: Supports hardware wavetable synthesis + audio playback, multifunctional MIDI DIN connector. www.excelvalley.com Contents Introduction 3 Resources 3 Specifications
More informationQuick Start for WT3 (v1.5) on Windows XP (and earlier)
Skip directly to the section that covers your version of Windows (XP and earlier, Vista or Windows 7) Quick Start for WT3 (v1.5) on Windows XP (and earlier) *** VERY IMPORTANT SAFETY NOTE *** NEVER connect
More informationPower Xpert Meter 2000 Gateway Card Kit
Quick Start Guide IL02601011E Rev. 2 December 2011 PXM 2250 PXM 2260 IQ 250 IQ 260 Power Xpert Meter 2000 Gateway Card Kit Table of Contents Remove the Meter From Service.... 2 Disconnect Power Connections,
More informationINSTALLING OR UPGRADING THE DVR S HDD
AHD & NVR SERIES INSTALLING OR UPGRADING THE DVR S HDD www.nightowlsp.com Installing or Upgrading the DVR s HDD Most DVR s included in our kits already have a pre-installed internal HDD and is ready to
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. CASSETTE/MP3 (EX) 2006 PILOT All 30488 Issue Date SEP 2005 Player Attachment Kit (sold separately) : P/N 08B06-S9V-100A Cassette Player
More informationWiring Classic MIDI Works Console Toe-Studs to the Classic MIDI Works Pedal Board (MKSC-4A encoder)
Wiring Classic MIDI Works Console Toe-Studs to the Classic MIDI Works Pedal Board (MKSC-4A encoder) The Classic MIDI Works Console Table comes with 16 brass toe-studs mounted 8 each on a slanted left and
More informationCourtesy of:discountcarstereo.com C5CD-HF. Quick Start Bluetooth Installation Guide for select Corvette with 12-Disc CD Changer
Courtesy of:discountcarstereo.com C5CD-HF Quick Start Bluetooth Installation Guide for select 1997-04 Corvette with 12-Disc CD Changer Created January 16, 2013 Revised March 12, 2019 Introduction: If your
More informationRAL-24192DM1 Setup Guide
RAL-24192DM1 Setup Guide Rev. 1.0 15/June/2012 RATOC Systems, Inc. www.ratocsystems.com Osaka, Japan Index 1. Introduction -------------------------------------------------------------------------- 3 1-1.
More informationInstallation & Quick Start Guide WL410 Wireless Adaptor/Antenna
Installation & Quick Start Guide WL410 Wireless Adaptor/Antenna QUICK START WL410-01- VR1.0 1. Introduction Congratulations on the purchase of your WL410 Wireless Adaptor/Antenna. This unit is designed
More informationKRONOS INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS TABLE OF CONTENTS ENCLOSURE AND DONGLE ASSEMBLY 1 LIGHTED ENCLOSURES 2-10 2 SLIM ENCLOSURE 11-17 3 WIRED-ETHERNET DONGLE 18-25 4 REAR-OFFSET MOUNT 26-33 5 SIDE-MOUNT 34-41 6 SURFACE
More informationCourtesy of:discountcarstereo.com USB-CDR30. ation Guide for Porsche CDR30/31. Radios Revised: January 10, 2018
Courtesy of:discountcarstereo.com USB-CDR30 Quick Start Installation ation Guide for Porsche CDR30/31 Radios Revised: January 10, 2018 Introduction: Portable audio products are everywhere, reflecting demand
More informationMBCD-HF. Quick Start Bluetooth Installation Guide for Select Mercedes with Changer. Courtesy of:discountcarstereo.com
Courtesy of:discountcarstereo.com MBCD-HF Quick Start Bluetooth Installation Guide for Select 1994-98 Mercedes with Changer Created September 3, 2016 Revised: March 24, 2019 Introduction: Safety comes
More informationCygnos360 V2 Installation Manual
Cygnos360 V2 Installation Manual VERSION 1.04. - MARCH, 2010 www.cygnos360.com Contents: Cygnos360 V2 Installation Manual... 1 1. What you need... 2 1.1. Tools... 2 2. Preparation... 3 2.1. Preparing the
More informationAUX-JAG/R* Quick Start Guide CD Changer. Courtesy of:discountcarstereo.com. Created May 3, 2016 Revised: January 5, 2018
Courtesy of:discountcarstereo.com AUX-JAG/R* Quick Start Guide for Jaguar x308 & x100 with CD Changer Created May 3, 016 Revised: January 5, 018 *AUX-JAGR connects to the Changer/Amplifier in boot/trunk
More informationOutdoor PTZ. Mounting on the Ceiling Using Pendant Mount. Installation Guide. For Models: I93, I94, I95, I96, KCM /12/03
Outdoor PTZ Mounting on the Ceiling Using Pendant Mount For Models: I93, I94, I95, I96, KCM-8211 2013/12/03 Table of Contents Mounting Solutions... 3 Straight Tube Installation Procedures... 4 Step 1:
More informationCheck the contents of the package
Read this first! UA-4FX Owner s Manual Copyright 2005 ROLAND CORPORATION All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION.
More informationNeve 8803 Dual EQ User Manual
Neve 8803 Dual EQ User Manual 527-370 Issue 2 AMS NEVE Billington Road Burnley Lancs BB11 5UB England Phone +44 (0)1282 457011 Fax: +44 (0)1282 417282 info@ams-neve.com www.ams-neve.com www.neve.eu - Page
More informationTechnovision Inc. CD-ROM Audio Sampler. Repair Manual
Technovision Inc. CD-ROM Audio Sampler Repair Manual Table Of Contents: Page # INITIAL SETUP & TESTING 3 System Components 3 System Set-Up Procedure 3 Self Test Routine 3 REPAIR ACTION PARTS REPLACEMENT
More informationCourtesy of:discountcarstereo.com MB-HF. Hands-Free & Streaming Audio Install Guide for Mercedes
Courtesy of:discountcarstereo.com MB-HF Hands-Free & Streaming Audio Install Guide for 1994-98 Mercedes Created September 3, 2016 Revised: March 23, 2019 Introduction: Safety comes first when you re on
More informationARC-CDJPLAYER INSTALLATION MANUAL Full plug and play kit, universal fit for use in Chrysler vehicles with RA1, RA2, RA3, or RA4 radios.
Required for Install: ARC-CDJPLAYER INSTALLATION MANUAL Full plug and play kit, universal fit for use in Chrysler vehicles with RA1, RA2, RA3, or RA4 radios. 1. Chrysler/Dodge/Jeep vehicle with Uconnect
More informationATTENTION: OBSERVE PRECAUTIONS FOR HANDLING ESD-SENSITIVE DEVICES
15 Monitor Removal 1. Turn off and unplug the game. 2. Place something in front of the game to brace the bezel once the strain relief cord is undone, then unlock and open the CPU section. 3. Remove the
More informationGotharman s DIY demoon
Gotharman s DIY demoon Assembly Manual Index Introduction 3 Mainboard Connections 4 Control Panel 5 Assembling The Full Kit 6 Assembling demoon From Mainboard Only 16 Mounting DIY demoon In A Box 18 Troubleshooting
More informationSeeburg JCU-DEC Kit Convert Your Seeburg DEC Wallbox Into a Jukebox
Seeburg JCU-DEC Kit Convert Your Seeburg DEC Wallbox Into a Jukebox MP3 Compact Flash Player Coin Operated or Free Play Integrated Power Amplifier Line-Out to External Amplifier Programmable Autoplay IR
More informationRoyal RVV-500 (B) Retrofit Kit
Optipay BV/RC/CC into a Non-Fascia Vending Machine This document contains information for installing and configuring the JCM Optipay DBV-01 Bill Validator, RC-10 Bill Recycler and A-66 Coin Changer into
More informationWindows 8 USB Instructions 05/13
Windows 8 USB Instructions 05/13 Page 1 - Driver Installation Page 6 USB Device Firmware version and update Page 10 Driver removal Page 12 Foobar2000 Installation and setup Installation of the MSB USB
More informationMytek FW DIO Card User Manual
Mytek FW DIO Card User Manual ver. 1.1 / Oct 2010 Mytek 2009 This manual may be updated Download the newest version at: http:///download_library/ For technical support, technical tips and support check:
More informationFlat Surfaced Ceiling Mounted Exterior Dome (Face Down) IN-DO2MIRVSLL, IN-DO4MF, IN-DO4M36A, IN-DO1MIRF, IN-DO2MIRF,
Outdoor Dome Flat Surfaced Ceiling Mounted Exterior Dome (Face Down) Installation Guide For Models: IN-DO2MIRVSLL, IN-DO4MF, IN-DO4M36A, IN-DO1MIRF, IN-DO2MIRF, IN-DO3MIRF, IN-DO5MIRF, IN-DO1MIRV, IN-DO2MIRV,
More informationZ Series and S4M Ribbon Take-Up Spindle Maintenance Kit
Z Series and SM Installation Instructions This kit includes the parts and documentation necessary to install the Ribbon Take-Up Spindle Maintenance Kit into the following printers: Z Series (ZM, Z6M, ZMplus,
More informationParts List: Assembly Instructions:
My Ride SERVICE MANUAl MyRide ASSEMBLY GUIDE 1.1 ASSEMBLY INSTRUCTIONS ASSEMBLING THE MYRIDE Parts List: Heavy Plate Stabilizer Fin - Right Stabilizer Fin - Left Stabilizer Fin - Large Middle Power Cord
More informationStandard Strip Series
Standard Strip Series Standard Strip STS-12 LED Lighting Systems Installation Manual (Version 1.3) YESCO LLC, 5119 South Cameron Street, Las Vegas, NV 89118 Table of Contents Introduction 1 Mounting Diagrams
More informationInstallation of advanced communications board and LG Chem RESU
Installation of advanced communications board and LG Chem RESU Introduction This technical note shows how to set up an SP PRO for use with an LG Chem RESU lithium battery. It explains how to update the
More informationENCORE /ST G4. Processor Upgrade Card for Power Mac G4 AGP Graphics. Quick Start Guide for Encore/ST G4
ENCORE /ST G4 Processor Upgrade Card for Power Mac G4 AGP Graphics Quick Start Guide for G4 Power Mac and Operating System Compatibility This G4 processor upgrade is compatible only with Power Mac G4 AGP
More informationSmartVR. Quick Start Guide. Release 2.0
SmartVR Quick Start Guide Release 2.0 www.veear.eu Table of Contents Introduction Read this first!... 3 SmartVR Product Description... 3 Hardware Setup... 4 Software Installation... 5 Running your first
More informationTau Camera Link Module Operation and Modification
Tau Camera Link Module Operation and Modification Application Note FLIR Commercial Systems 70 Castilian Drive Goleta, CA 93117 Phone: +1.805.964.9797 www.flir.com Document Number: 102-PS242-100-02 Version:
More informationMorse Code Practice Oscillator
Features Description Keyer speed range: Limited only by keying source True Sine wave tone output Tone Volume Control Tone Frequency Control Internal Speaker 1/8 External Speaker/Headphone Jack RCA Key
More informationPower Xpert Meter 2000 Gateway Card Kit
Quick Start Guide IL02601011E PXM 2250 PXM 2260 IQ 250 IQ 260 Power Xpert Meter 2000 Gateway Card Kit Table of Contents Remove the Meter From Service... 2 Disconnect Power Connections, CTs, and Modbus....
More informationInstalling the driver software USB Audio Driver Installation Manual (Mac)
Installing the driver software USB Audio Driver Installation Manual (Mac) Contents Installing the driver software... Page 1 To uninstall the driver... Page 4 Troubleshooting... Page 5 The driver name and
More informationVersion 1.4. MA-1 Stereo D/A Converter Manual
Version 1.4 001 Safety Instructions Safety Instructions 002 Prior to Installing you new Meitner Audio product please read the following safety instructions: Read and follow all instructions. Keep these
More informationJanuary Bob Wright. 1 P age Bob Wright
The upgrade is completed using the 401 control board and three Step1 driver boards supplied as a kit by Conqueror Design and Engineering Ltd. The kit includes all cable terminators for connections to the
More informationSIGN MAGNITUDE LADDER DAC SPECIFICATIONS INPUTS: RCA OUTPUTS: OUTPUT IMPEDANCE: BALANCED OUTPUT: VOLUME CONTROL: 2 db STEPPED ATTENUATOR (32
Reference CD II Station Users Manual Rev 1 (1/03) INPUTS: SIGN MAGNITUDE LADDER DAC SPECIFICATIONS RCA OUTPUTS: OUTPUT IMPEDANCE: BALANCED OUTPUT: COAXIAL, TOSLINK, BALANCED AES/EBU, 1 MSB NETWORK (192K)
More informationUser s Guide TURBO Pinewood Derby Finish Line and Timer Release /31/2011 NewBold Products, Atlanta GA
User s Guide TURBO Pinewood Derby Finish Line and Timer Release 2.1 12/31/2011 NewBold Products, Atlanta GA www.newboldproducts.com 2 1. YOUR SHIPMENT Thank you for purchasing the TURBO, Pinewood Derby
More informationDISCLAIMER PLEASE READ
NSM4MP3 HDD or CF MP3 Player For Your NSM ES-IV CD Jukebox Works with all laptop/notebook HDD s Supports all layer-iii (MP3) encodings Variable or fixed bit rates to 320 Kbps Detects master/slave drive
More informationPARTS LIST 1 x PC Board 36 x 5mm Red LED 36 x 12mm LED Standoff 36 x NPN Transistor 36 x 10kΩ Resistor OTHER PARTS YOU MAY NEED
PARTS LIST 1 x PC Board 36 x 5mm Red LED 36 x 12mm LED Standoff 36 x NPN Transistor 36 x 150Ω Resistor 36 x 10kΩ Resistor 17 x Mini Toggle on-off 8 x Mini Toggle (on)-off-(on) 1 x 470Ω Resistor 1 x 47µF
More informationCourtesy of:discountcarstereo.com IP-JAG98
Courtesy of:discountcarstereo.com IP-JAG98 Quick Installation Guide for Jaguar x308 & x100 with CD Changer Select 1997-06 Standard and Premium Systems Created May 3, 016 Revised: December 10, 018 Introduction:
More informationDetailed Installation Guide. Version 1.0
Detailed Installation Guide Version 1.0 Copyright 2009 Table of Contents Table of Contents General Guidelines...3 Kontakt Requirements...3 System Specifications...3 Installation of LASS DVDs...4 What to
More information2.5" SATA to USB 3.0 & esata External Hard Drive Enclosure USER S MANUA L
2.5" SATA to USB 3.0 & esata External Hard Drive Enclosure USER S MANUA L Package Contents: 2.5" SATA to USB 3.0 & esata External Hard Drive Enclosure 1 2.5 NexStar 3 SuperSpeed USB 3.0 & esata Enclosure
More informationIQ32 Upgrade Kit Assembly Instructions
IQ32 Upgrade Kit Assembly Instructions Jim Veatch WA2EUJ September 17, 2018 TABLE OF CONTENTS 1. INTRODUCTION... 3 2. IQ-32 UPGRADE KIT INVENTORY... 4 3. PREPARING THE RS-HFIQ AND SIDE PANELS... 6 4. CONNECTING
More information