DIGITAL HEIGHT GAUGE OPERATION AND MAINTENANCE MANUAL
|
|
- Lisa Fisher
- 5 years ago
- Views:
Transcription
1 OPERATION AND MAINTENANCE MANUAL Before operating the instrument, please read the manual thoroughly, and retain it for future reference. IMPORTANT! Do not use the instrument near a high-voltage or magnetic equipment. Do not measure electrified body. Do not disassemble or modify the instrument and any excessive shock should avoided. The carbide- tipper scriber is very sharp. Handle it carefully to avoid injury. Wipe the anti-rust oil from the instrument with a soft cloth when use the instrument at the first time; and make sure the carbide-tipper scriber, the racks, the base and other reference surface of the instrument are clean. Please take anti-rust oil, if do not use the instrument for a long time. Before taking measurements with the instrument, take sure "ORG "is ok. NOTES! (Non fault phenomenon) Status light brightness changes:without any operation in 3 minutes, the system will turn to sleeping mode. There are two options for turn the driving wheel or press any key to restore display. Auto Power Off: More than 30 minutes without any operation, pressing " " Key for restart the instrument. FEATURES High accuracy Clear OLED display Auto/delay power- off Power: 3.7V rechargeable lithium-ion battery Relative humidity: 80% Operating temp.:0 ~40 Storage temp.:-20 ~60 FUNCTIONS Language selection Absolute/relative measurement Ability to hold the measured values Preset function for entering a known value or initial value Bluetooth data output Absolute origin correction Metric/inch conversion Zero- setting of display Set and determine tolerance SPECIFICATION Range Resolution Accuracy 0-300mm/ mm/.0005 ±0.015mm 0-500mm/ mm/.0005 ±0.025mm 0-600mm/ mm/.0005 ±0.025mm 1
2 NOMENCLATURE Digital parts Scriber clamp box Scriber Stopper Locking device driving wheel Locking nut Slider Spherical contactor Column Plane contactor Base charging port Reset Fig.1 CONTROL PANEL Data hold prompt Measuring data 2nd function prompt Mode conversion Tolerance determine Power Origin correction INSTALL BATTERY INC prompt Bluetooth output HOLD INC TOL Tolerance determine prompt Unit Power prompt Status light Charging light Bluetooth prompt Inch,Metric setting ABS,INC measurement 2nd function Zero set Data hold Tolerance prompt Fig.2 Unscrew the battery lid screw, remove the battery lid, pull out the interface plug from the battery box,and connect battery. Push the battery with the belt and cable into the battery box then cover the battery lid and tighten the screw (Fig.3). Plug(in the battery box) Belt Plug Battery Fig.3 When charging? Change the battery, when the instrument not function and the power light twinkle, Insert the charger plug to power, the charging begins when the red light is on. It shows charging complete when the red light is off. USING ATTACHMENT Fig.4 KEY FUNCTION About " ", "in/mm", "", " ZERO" and "HOLD" key Pressing " " Key for power on or off. Pressing "in/mm " key for changeover between metric and inch. 2
3 Pressing " " key for changeover function mode with other key. Pressing "ZERO " key for zero-setting of display anywhere within the measuring range. Pressing "HOLD" key at any position, the OLED will display and hold the measured value of this location. About "ORG " key "ORG" mode is used to correct the origin of the instrument. Do not measure in ORG state, should be correct the origin after to start measuring. Before using this instrument for the first time, change the battery, after the battery ran out and press the reset button to restart the system, please re-correct the origin. Suggest correction the origin on a regular. Operating steps: (1)Pressing""and"ORG"key on the control panel, the OLED will display the interface: (When change the battery, after the battery ran out and restart the system, will automatically enter the interface.) (2) Turn the driving wheel slowly and make the slider move down until make the spherical contactor contact with the plane contactor on the base (Fig.5), If the OLED display this interface: then pressing "" and "ZERO" key, BASE the OLED will display,it shows correction complete. Fig.5 Pressing "" and" ORG" key to exit then you can start making measurements. If the OLED display such as interface, and there is" Force Over" prompt, it shows the measuring force is too large, please according to the step (2) operation again. About "MODE" key "MODE" mode is used to set one of the function: selection language and set tolerance and preset H and set Bluetooth data output and so on(fig.6, Fig.7, Fig.17, Fig.21). About language selection (Fig.6): MODE (five times) in/mm or ZERO: Selection language MODE EXIT About TOL key Fig.6 " TOL" mode is used to determine tolerance (1)Setting the tolerance limits (Fig.7): For example ( mm) MODE (twice ) MODE MODE EXIT (2)Using: Fig.7 Pressing "TOL" key the OLED will display "TOL" prompt, the digital height gauge worked at determining tolerance mode at the moment 3
4 (Fig.8). When measured values beyond the limits of tolerance, the OLED will display "+ OV "or "- OV " prompt during the measurement (Fig.9, Fig10). If no prompt, it shows the measured values is qualified (Fig.11). Pressing "TOL" key once more to exit and the "TOL" prompt disappear. Fig.8 Fig.9 Fig.10 Fig.11 About "ABS " key "ABS" mode is default setting. For example (Fig.12): (1) Pressing "ZERO" key at position 1 (datum plane),then complete measurement at position 2, the OLED will display measured value (Fig.13); (2) Pressing "ABS" key the OLED will display "INC" prompt at position 2, this moment the digital height gauge worked at "INC" (comparison)mode, and the display be reset(fig14.), the slider move upwards and complete measurement at position 3, the OLED will display reading of this time(fig.15). At this moment if pressing "ABS" key once more, then the OLED will display the sum of the front reading and reading of this time (from datum plane to position 3) (Fig.16). ("ABS") ("INC") ("ABS") 2 1 Datum plane Fig.12 Preset function(digital entry) 3 Fig.13 Fig.14 Fig.15 Fig.16 Preset function is used to enter a known value for a reference plane which cannot be directly contacted by the height gauge measures distances from the indirect reference to any surface of the workpiece. For example (Fig.18): (1)Preset H: Before taking measurement with the height gauge, enter a known value for a reference plane at first (Fig.17). MODE MODE EXIT Fig. 17 (2)Using: Pressing "" and "ZERO" key, the OLED will display the preset value of the reference plane(fig.19), this moment the digital height gauge worked at presetting function mode. And go on measuring at the need to measure position. the OLED will display the sum of the front reference reading and reading of this time (Fig.20). H Preset H Fig.19 Fig.20 Datum plane Fig.18 About " " key and Bluetooth The mode is used to fill the measured value in the blank of the report file with WORD, EXCEL or NOTEPAD, etc. Bluetooth data output formats (Fig.21): MODE (four times) Fig.21 4 MODE EXIT
5 Notes: Those functions are the same as icon buttons " ", " ", " ", " ", " ", " " in the interface as the corresponding computer keyboard keys. The cursor will move according to the selected mode. Using: (1) Pressing "" and " " key on the digital panel, the OLED will display " " icon, it shows Bluetooth function has turned on. (2) User pairing(bluetooth Version 2.1 and above): 1Paired with the computer:before using, please make sure Bluetooth drivers has installed on the computer: Find out the" " icon in the lower right corner of computer, right-click " " and select "Add Devices", or click "Control panel" and select "Device manager", "Devices and printers", "Add Devices" in turn, and then waiting for showing "HG2400", double-click "HG2400"complete matching, you can use the Bluetooth function. 2Paired with mobile phone: Find out and click " "icon on the phone then select "search equipment" and then waiting for showing "HG2400", next to click "HG2400"complete matching, you can use the Bluetooth function. (3)start transmitting:open the report file, take the cursor to stays the filling position then press ""and" " key on the digital panel, the measured value will be output and filled in the blank. Press the " " key on the digital panel each time, a data will be output. (4)Pressing "" and " "key again, the Bluetooth function is disabled, and the " "icon disappear. ACCESSORIES NAME QUANTITY NAME QUANTITY NAME QUANTITY Carbide tipper scriber 1 driver 1 Battery 1 Clamping slider 1 Needle 1 Report 1 Attachment 1 Charger 1 Operation manual 1 5
Data Sheet: LDS 1367 Date:
Product: Electronic Digital Measuring Set Page 1 of 5 Digital Caliper and Electronic Micrometer Set Set contains: 1 x Electronic Caliper: 150mm/6 1 x Electronic Micrometer: 0-25/0-1 mm Housed in a fitted
More information5.6" Multi-function Monitor
5.6" Multi-function Monitor User s Manual Please read this Manual carefully before use of this product, and keep it handy for future reference. I. Packing List.. 2 II. Product Appearance... 3-5 III. Product
More informationUser Manual Series Electronic Indicator. starrett.com
User Manual 2900 Series Electronic Indicator starrett.com Table of Contents Guidelines for Indicator Care... 2 Operating Instructions... 3 Indicator Components, Dimensions & Layout... 3 Button Functions...
More informationUser Manual Revised 1-July-2015
User Manual Revised 1-July-2015 LIMITED WARRANTY AND LIMITATION OF LIABILITY The use of the Auguscope is subject at all times to Augury's standard Management Platform Terms of Use, which can be viewed
More informationUser Manual IP Capacitive Series Electronic Indicator M ME M ME-25. starrett.
User Manual 2900 Capacitive Series Electronic Indicator IP67 2900-3-1 2900-3M-25 2900-3ME-25 2900-5-1 2900-5M-25 2900-5ME-25 Table of Contents Guidelines for Indicator Care... 2 2900 Capacitive Series
More informationHeightmatic SERIES 574 High Precision Height Gage
Height Gages Heightmatic 159 Digimatic Height Gage 160 ABSOLUTE Digimatic Height Gage 162 Dial Height Gage 164 Vernier Height Gage 166 CERA Caliper Checker 168 Carbide-tipped Scriber 169 Optional Accessories
More informationLS516/LSG516 Self-leveling Rotating Laser Instruction Manual ( )
LS516/LSG516 Self-leveling Rotating Laser Instruction Manual (2009-8-14) Contents 1. Features and Functions 2. User Safety 3. Nomenclature 4. Operation Instruction 5. Self-check and calibration 6. Application
More informationSTEINDORFF. LCD Digital Stereo Measuring Microscope NYMCS-343. Instruction Manual
STEINDORFF LCD Digital Stereo Measuring Microscope NYMCS-343 Instruction Manual This manual is written for Industrial LCD Microscope NYMCS-343. For safety and for exerting the best performance, making
More informationTable of contents. Safety recommendations...3. Warning Notice..4
Table of contents Safety recommendations...3 Warning Notice..4 1. Description...5 2. Preparation for use... 6 3. Menu set up...7 4. Digital Zoom......8 5. LED Adjustment......9 6. Mirror / Reflecting Object
More informationElectronic Indicator
IN/MM 2ND TOL Electronic Indicator Operating Manual Non-Analog Digital Display 3 Programmable Presets and 3 Programmable Ratios Extra-Large Number Display Incremental Measuring Mode SPC Cables USB, MTI,
More informationDear user, Thank you very much for purchasing LS533H rotary laser. Please read this instruction manual before operating it.
Dear user, Thank you very much for purchasing LS533H rotary laser. Please read this instruction manual before operating it. Contents 1. Features and Functions 2. User Safety 3. Nomenclature 4. Operation
More informationFG-3000R Digital Force Gauge Operation Manual
FG-3000R Digital Force Gauge Operation Manual Operators should wear protection such as a mask and gloves in case pieces or components break away from the unit under test. Whether the unit is ON or OFF,
More informationFG-3000 Digital Force Gauge Operation Manual
FG-3000 Digital Force Gauge Operation Manual Operators should wear protection such as a mask and gloves in case pieces or components break away from the unit under test. Whether the unit is ON or OFF,
More informationISH-DSA DIGITAL SHORE DUROMETER OPERATION MANUAL
ISH-DSA-E www.insize.com ISH-DSA DIGITAL SHORE DUROMETER OPERATION MANUAL V0 1. Attention Only authorized charger is allowed to be applied to this, otherwise it will be damaged permanently. Any part of
More informationUSER GUIDE 12.5" Ultra Slim Laptop
ELL1201T USER GUIDE 12.5" Ultra Slim Laptop Designed by the EPIK Learning Company California, USA www.epiklearning.com. Introduction and Table of Contents TABLE OF CONTENTS Page 1.0 Introduction... 1
More informationAuto-leveling Rotating Laser (RL430G)
Auto-leveling Rotating Laser (RL430G) Congratulations on your choice of this Auto-leveling Rotating Laser. For the purpose of long-term use of this instrument, we suggest you to read this instruction manual
More informationPlease refer to Page 3.
C. Insert the accessory CD into computer and open the following path: CD-ROM drive Chinese SH and ST port software SundooPor t SundooPor t. exe; This software need not be installed, and you only have to
More informationFG-7000 Digital Force Gauge Operation Manual
FG-7000 Digital Force Gauge Operation Manual Operators should wear protection such as a mask and gloves in case pieces or components break away from the unit under test. Whether the unit is ON or OFF,
More informationTable of Contents & Introduction 2 Product features & Function. 3. Calibration RS232C Serial communication...6 Specifications
High Precision 2-Axis Digital Electronic Inclinometer IM-2DW User s Guide The contents of this manual could be different according to the software version and it can be changed without notice. Please use
More informationModel No INSTRUCTION MANUAL. Manual should be read prior to operation!
Model No. 15950 INSTRUCTION MANUAL Manual should be read prior to operation! CONTENTS 1) GENERAL 3 2) WORK PRINCIPLE AND STRUCTURE FEATURES 3 3) MAJOR TECHNICAL PARAMETERS 4 4) USE AND OPERATION 5 5) MAINTENANCE
More informationFlare. Smart Activity Tracker. Quick Start Guide. delvfire.com PHONE/TABLET REQUIREMENTS QUICK START GUIDE
PHONE/TABLET REQUIREMENTS ios 7.1 & above Android 4.5 & above Bluetooth 4.0 QUICK START GUIDE Flare Smart Activity Tracker Quick Start Guide ID115U 1. Download the VeryFitPro App To set up your tracker
More informationSeries FGE-XY Force Gauges Operation Manual
Series FGE-XY Force Gauges Operation Manual Do not operate or store instrument in the following locations: Explosive areas, near water, oil, dust or chemicals; areas where the temperatures can exceed 104
More informationTable of Contents & Introduction 2 Product features & composition. 3 Functions Specifications
High Precision Wireless Bore Gauge B-100 User s Guide The contents of this manual could be different according to the software version and it can be changed without notice. Please use this good after reading
More informationFeatures. Warnings and Precautions READ BEFORE OPERATING EQUIPMENT SAVE THESE INSTRUCTIONS
SENTA Warnings and Precautions READ BEFORE OPERATING EQUIPMENT SAVE THESE INSTRUCTIONS To prevent damage to your radio or possible injury to you or others, read these safety precautions and instructions
More informationNIDEC-SHIMPO INSTRUMENTS
Series FGE-XY Force Gauges Operation Manual NIDEC-SHIMPO INSTRUMENTS Do not operate or store instrument in the following locations: Explosive areas, near water, oil, dust or chemicals; areas where the
More informationUWE-1707 SERIES CONTENTS OPERATION MANUAL ELECTRONIC WEIGHING INDICATOR 1. SPECIFICATIONS 2. INSTALLATION
UWE-1707 SERIES CONTENTS ELECTRONIC WEIGHING INDICATOR OPERATION MANUAL 1. SPECIFICATIONS PLEASE READ THIS MANUAL VERY CAREFULLY BEFORE ATTEMPT TO OPERATE THE SCALE 2. INSTALLATION 3. ROUTINE OPERATION
More informationSpring tension and compression testing machine
Postscript USEGA MANUAL Honorable users: Thank you for purchasing our ATH Spring tension and compression testing machine. Before you use it, please really this operation instruction carefully so that proper
More informationHomework 13: User Manual
Homework 13: User Manual Team Code Name: Autonomous Targeting Vehicle Group No. 3 User Manual Outline: Brief (marketing-style) product description Product illustration annotated with callouts for each
More informationHandheld Inspection Scope. User s Manual
Handheld Inspection Scope User s Manual Safety recoendations DANGER This device must not be used for medical or veterinary purposes. Do not use this item in explosive atmospheres. WARNING Do not modify
More informationDigimatic. Height Gages. Linear Height. Depth Gages. SuperCaliper ABSOLUTE. Coolant Proof Caliper. ABSOLUTE Digimatic Caliper ABSOLUTE
D Small Tool Instruments and Data Management Digimatic Caliper Digimatic Height Gages Linear Height Depth Gages SuperCaliper ABSOLUTE Coolant Proof Caliper ABSOLUTE Digimatic Caliper ABSOLUTE Digimatic
More informationMANUAL SURFACE ROUGHNESS TESTER TR-200 PARTNERS IN PRECISION
MANUAL SURFACE ROUGHNESS TESTER TR-200 PARTNERS IN PRECISION CONTENTS 1 Overview 5 1.1 Measurement principles 5 1.2 Standard configuration 6 1.3 Names of each part of the instrument 6 1.4 Basic connection
More informationOven Loggermaster BEVS User Manual
Oven Loggermaster BEVS 2301 User Manual Version This manual shall be read carefully before starting. Directions included in this operation manual shall be strictly followed PAGE 1 Catalogue 1. Brief Introduction
More informationUser Manual. NOTE: For Spanish users, please go to 'Settings", then go to Language & Input to change from English to Spanish Language OSD.
User Manual NOTE: For Spanish users, please go to 'Settings", then go to Language & Input to change from English to Spanish Language OSD. 17.3 All in One To assure the product to work in best status please
More informationShore D Hardness Tester TH210. Instruction Manual. TIME GROUP INC. Beijing Time High Technology Ltd
Shore D Hardness Tester TH210 Instruction Manual TIME GROUP INC. Beijing Time High Technology Ltd 1 Contents Chapter 1. Introduction... 1 1.1 Main features and application...4 1.2 Fundamental...4 1.3 Basis...5
More informationNEW 1060PLUS Graphics Tablet. User Manual. For Windows and Macintosh OS
User Manual For Windows and Macintosh OS Precautions 1. Please read this manual carefully before using, and keep it well for future reference. 2. Before cleaning the tablet please unplug the power cord
More informationHeight Gauge Page 234. Height Gauge Accessories Page 241
Height Gauges Height Gauge Page 234 Height Gauge Accessories Page 241 Height Gauge with Data Processing Unit Page 243 233 Lightweight Vernier Height Gauge Series 506 This vernier height gauge offers you
More informationFG-7000L Digital Force Gauge Operation Manual
FG-7000L Digital Force Gauge Operation Manual Operators should wear protection such as a mask and gloves in case pieces or components break away from the unit under test. Whether the unit is ON or OFF,
More informationImportant About Camera
1 Thank you for purchasing the GoXtreme Full Dome 360. This 360 camera allows you to capture, view and share amazing full panoramic 360º videos and photos. When viewed using the companion app or desktop
More informationTablet PC User Manual
Tablet PC User Manual Please read all instructions carefully before use to get the most out of your Time2Touch Tablet PC. The design and features are subject to change without notice. Contents Important
More informationSHIMPO INSTRUMENTS. FG-7000T Digital Torque Gauge Operation Manual
FG-7000T Digital Torque Gauge Operation Manual SHIMPO INSTRUMENTS Operators should wear protection such as a mask and gloves in case pieces or components break away from the unit under test. Whether the
More informationCONTENT Warning...1 I.Brief Introduction...3 II.Electrical Symbol...4 III.Series Model...4 IV. Technical Specifications...4 V.
CONTENT Warning...1 I.Brief Introduction...3 II.Electrical Symbol...4 III.Series Model...4 IV. Technical Specifications...4 V. Instrument Structure...6 VI. Instrument Operation...7 1 Turning on and off...7
More informationBORESCOPE INSTRUCTIONS INSPECTION CAMERA RANGE RBS100 RBS200 RBS300. Retain these instructions for future reference
BORESCOPE INSPECTION CAMERA RANGE RBS100 RBS200 RBS300 INSTRUCTIONS Retain these instructions for future reference www.ringautomotive.co.uk 1 Instructions for Ring Automotive Borescope Inspection Camera
More informationSP-L51. Portable Thermal Printer. User s Manual VER 1.00
SP-L51 Portable Thermal Printer User s Manual VER 1.00 1 Content NOTICE... 3 Notice of Safety... 3 Notice of Using... 3 Notice of Storing... 3 Chapter 1 Outer Appearance and Model No.... 4 1.1 Outer Appearance...
More informationNIDEC-SHIMPO INSTRUMENTS
Series FGE-HXY Force Gauges Operation Manual NIDEC-SHIMPO INSTRUMENTS Do not operate or store instrument in the following locations: Explosive areas, near water, oil, dust or chemicals; areas where the
More informationTHREAT-FIRE MANUAL SYSTEM SPECS AND OPERATION INSTRUCTIONS. Version
SYSTEM SPECS AND OPERATION INSTRUCTIONS Version 1.0-0316 2016 by VirTra Inc. All Rights Reserved. VirTra, the VirTra logo are either registered trademarks or trademarks of VirTra in the United States and/or
More informationOPERATING MANUAL FOR LOGIC BASIC SERIES ELECTRONIC INDICATORS
OPERATING MANUAL FOR LOGIC BASIC SERIES ELECTRONIC INDICATORS Choice of Three Power Sources 1. Batteries A set of two Manganese Dioxide Lithium batteries will operate this electronic indicator for approximately
More informationInstruction Manual RS-1660
Instruction Manual RS-1660 Transformer Turns Ratio Meter This unit passes the following tests: Safety Symbols EN 61010-1: 2010 EN 61010-2-030: 2010 CAT IV 50V Pollution Degree 2 EN 61326-1: 2013 (CISPR
More informationPowerView Model PV780. Operations Manual Section 78
PowerView Model PV780 Operations Manual 00-02-0859 2013-03-19 Section 78 In order to consistently bring you the highest quality, full featured products, we reserve the right to change our specifications
More informationElectronic Indicator
TIR ABS CR /MM Electronic Indicator Operating Manual Analog Display Analog Visual Display Incremental Measuring Mode SPC Cables USB, MTI, RS232 Measuring System in English or Metric Travel Reverse Auto
More informationOperating Instructions for Orderman Sol & Sol+
Operating Instructions for Orderman Sol & Sol+ 2010 by Orderman GmbH Bachstrasse 59, 5023 Salzburg Austria www.orderman.com Errors and misprints excepted. Duplication, reproduction or distribution, even
More informationLinear Height LH-600E SERIES 518 High-Performance 2D Measurement System
Linear Height LH-0E SERIES 518 High-Performance 2D Measurement System Excellent accuracy of (1.1+0.6L/0)µm with 0.1µm/0.5µm resolution/repeatability. Perpendicularity (frontal) of 5µm and straightness
More informationSLIMLINE DASH CAM Audio & Video Recorder
SLIMLINE DASH CAM Audio & Video Recorder 1 EK142CAM INSTRUCTION MANUAL PLEASE READ ALL INSTRUCTIONS CAREFULLY AND RETAIN FOR FUTURE USE Getting Started Remove the Car Digital Video Recorder from the box.
More informationTablet PC User Manual
Tablet PC User Manual Please read all instructions carefully before use to get the most out of your Time2Touch Tablet PC. The design and features are subject to change without notice. Contents Important
More informationDYNASCAN D-250 2D+ Ø DRO
DYNASCAN D-250 2D+ Ø DRO The D-250 is an advanced digital readout system for performing three axes (two linear and one angular) geometrical measurement at very high level of precision and accuracy. Its
More informationCONTENTS Introduction 4 DTR overview 4 probes 5 functions 5 display 5 DTR operation 6 switching the DTR on or off 6 changing label 6 displaying
User Manual 2 CONTENTS Introduction 4 DTR overview 4 probes 5 functions 5 display 5 DTR operation 6 switching the DTR on or off 6 changing label 6 displaying limits 6 feeding paper 6 printing a ticket
More informationIngram FAQs. Q: Cursor does not follow the movements of the M570 Wireless Trackball?
Ingram FAQs Logitech Wireless Trackball M570 (3574): Q: Why is my mouse double clicking, when I click once? Q: My M570 keeps losing connection? A: Firstly, check the batteries to make sure this isn t the
More informationDI-5C. Prisma INSTRUMENT USER MANUAL
DI-5C Prisma INSTRUMENT USER MANUAL INDEX 1. Instrument overview 2. How to use the instrument 2:1 Description 2:2 Display 2:3 On/Off & push buttons 2:4 Settings Set date / time Change number of digits
More informationUser Manual. Borescope. Model THE STANDARD IN PRECISION MEASUREMENT
User Manual Model 20250-28 Borescope THE STANDARD IN PRECISION MEASUREMENT Introduction The Digi-Sense Borescope (Model 20250-28) is ideal for the inspection of ductwork, wiring locations, piping, vehicles,
More informationThanks for buying our product. Specialty of IM-2DT
High Precision 2-Axis Digital Electronic Inclinometer IM-2DT User s Guide The contents of this manual could be different according to the software version and it can be changed without notice. Please use
More informationThese items can be purchased separately or as a kit from your distributor.
Unpack Your Printer 1 Unpack Your Printer The following items are included in the standard BMP 53 Mobile Printer package: BMP 53 printer MC-1500-595-WT-BK cartridge USB connection cable Product CD Brady
More informationSurface Roughness Tester. Instruction Manual.
YRT100 Surface Roughness Tester Instruction Manual Please visit for more details Content 1 General Introduction... 3 2 Work Principle... 4 3 Name of each components... 5 4 Technical Parameters... 5 5.
More informationThank you very much for purchasing LAISAI LS686 line laser, please read this instruction manual before operating it. Content
Dear User: Thank you very much for purchasing LAISAI LS686 line laser, please read this instruction manual before operating it. Content 1. Features and functions 2. User safety 3. Instrument nomenclature.
More informationTable of Contents. Introduction 2 1. Intelligent Remote Control 2 2. Charging the Remote Control 3
Table of Contents Introduction 2 1. Intelligent Remote Control 2 2. Charging the Remote Control 3 Getting Started 6 1. Activating the Remote Control 6 2. Selecting a Device 7 3. Operating a Device 8 4.
More informationTemperature logger with internal sensor Instruction manual
LOGGER R0110 Temperature logger with internal sensor Instruction manual Manual for use of temperature logger R0110 Logger is designed for measurement and record of temperature from built-in internal temperature
More informationStarryBay. User Guide
StarryBay User Guide SW-08 Smart Watch 1 / 13 Contents 3 Chapter 1: Overview 3 External part & Internal part 3 Accessories 3 On screen keyboard 4 Basic gestures 5 Status icons 6 Three working modes 7 Chapter
More informationCALOG CALOG - LC DISPLAY. Loadcell Display. English Users Manual. Rev. 1.10
CALOG C A L I B R AT O R S CALOG - LC DISPLAY Loadcell Display English Users Manual Rev. 1.10 Table of Contents! Contents! 1.0 Introduction...2! 2.0 Getting Started...2! 2.1 Keypad...2! 2.2 Display...2!
More informationAK-C6A In Car Dash Camera. Instruction Manual Model Ref: MM347
AK-C6A 20032017 In Car Dash Camera Instruction Manual Model Ref: MM347 Introduction Thank you for choosing this In Car Dash Camera. This product is manufactured to the highest standards of performance
More informationDIGITAL INDICATOR USER MANUAL
DIGITAL INDICATOR USER MANUAL LMI Corporation Linear Measurement Instruments 101 N. Alloy Drive Fenton, MI 48430 810-714-5811 www.lmicorporation.com www.lmicorporation.com 1 TABLE OF CONTENTS SECTION PAGE
More informationISR-S400 ROUGHNESS TESTER OPERATION MANUAL
MN-ISR-S400-E www.insize.com ISR-S400 ROUGHNESS TESTER OPERATION MANUAL V0 Attention Product Introduction To get the best results from this instrument and to use it satisfactorily, first read this manual.
More informationDigital Ink Pad+ User Manual
Digital Ink Pad+ User Manual Page 1 Welcome. Dear user, thank you for purchasing this product. Much investment in time and effort has gone into its development, and it is our hope that it will give you
More informationQuick Start Guide Notion Ink Design Labs Pvt. Ltd. 1
Quick Start Guide 2014 Notion Ink Design Labs Pvt. Ltd. 1 2014 Notion Ink Design Labs Pvt. Ltd. 2 Contents 1. Caring for your device 2. Travelling with your device 3. Device layout 4. Keyboard case layout
More informationCareFusion. Overview of the CareFusion Device. Press Red button on top right-hand corner to turn device on and off
Tim Hamill, M.D. Digitally signed by Tim Hamill, M.D. DN: cn=tim Hamill, M.D., o, ou=ucsf Clinical Laboratories, email=hamillt@labmed2.ucsf.edu, c=us Date: 2009.04.20 20:57:31-07'00' CareFusion Summary:
More informationARA FTS Flow Calibrator. Operation Manual August 1, 2016
ARA FTS Flow Calibrator Operation Manual August 1, 2016 TABLE OF CONTENTS SECTION PAGE 1. INTRODUCTION 1 2. GETTING STARTED 1 2.1. Navigation 1 2.2. Charge Battery 1 2.3. Set Date and Time 2 2.4. Plug-In
More informationSPECIAL OFFERS 16,995 METROLOGY DIRECT 4,000. Micro-Vu Vertex 110 Vision Measuring System 2008 AUTUMN / WINTER PROMOTION
Micro-Vu Vertex 110 Vision Measuring System Comprises: Vertex 110 with 200x150x150mm measuring range Dell PC and 17 TFT monitor Windows XP Inspec automated vision software High resolution video system
More informationHEIGHT GAUGES. Moore & Wright Vernier Height Gauge 190 Series. Digital Mini Height Gauge 192 Series. Partners in Precision
Moore & Wright Vernier Height Gauge 190 Series Zero reference point can be adjusted for calibration Hardened stainless steel beam Measuring faces are micro-lapped for high accuracy Chrome plated scale
More informationPRECISION MEASURING INSTRUMENTS
PRECISION MEASURING INSTRUMENTS STANDARD GAGE PROFESSIONNEL MEASURING INSTRUMENTS AFFORDABLE TO EVERYONE The instruments of the STANDARD GAGE product line were created to satisfy the clients on their query
More informationContents. Contents. Operating Hints. Overview. Digital Night Vision Monocular. Contents P P1-0540
Contents Contents Digital Night Vision Monocular Model: Contents Overview 3 Operating Hints 4 Components 5 7 Battery Installation 7 Power On 8 Power Off 8 Scenery Observation 9 Screen Brightness 10 Photo
More information7 LCD CCTV Test monitor. Quick guide
Thank you for purchasing our product. Speco Technologies is constantly developing and improving products. We reserve the right to modify product design and specifications without notice and without incurring
More informationUser Manual Video Borescope Model
User Manual Video Borescope Model 20250-27 THE STANDARD IN PRECISION MEASUREMENT Introduction The Digi-Sense Video Borescope (Model 20250-27) is ideal for the inspection of ductwork, wiring locations,
More information-Direct.com FG-3000 Digital Force Gauge Operation Manual
FG-3000 Digital Force Gauge Operation Manual Operators should wear protection such as a mask and gloves in case pieces or components break away from the unit under test. Whether the unit is ON or OFF,
More informationCurrency Detector. Operation Manual South Grand Ave., Glendora, CA
Currency Detector Operation Manual 1743 South Grand Ave., Glendora, CA 91740 www.fraudfighter.com 800.883.8822 Catalogue CT-550 USER MANUAL Safety Instructions................................................
More informationIGB Series. Operation Manual. Platform Scale. Kg/Lb Specification IMPORTANT
Platform Scale IGX/ Kg/Lb Specification Operation Manual IMPORTANT Do not carry out installation, operation, service, or maintenance until thoroughly understanding the contents of this manual. Keep this
More informationACTIVE FIT+HR. Fitness Tracker Activity Band USERS GUIDE
ACTIVE FIT+HR Fitness Tracker Activity Band USERS GUIDE Getting Started Thank you for choosing the Jarv Active Fit +HR Fitness Tracker Activity Band. Please take the time to read this manual carefully,
More informationSNAP STICK. Wireless Smartphone Camera Stick with Bluetooth USER GUIDE
SNAP STICK Wireless Smartphone Camera Stick with Bluetooth USER GUIDE Getting familiar with your 3SIXT SNAP STICK Clamp 2 Snap Stick c 1 Press Button USB Cable 4 3 Stopper b USB Charging Port LED Light
More informationSet: User manual. Smartphone Application SLT-caliper. Codimex E1 - Electronic caliper
Set: Codimex E1 - Electronic caliper Smartphone Application SLT-caliper User manual Contents page 1. Introduction... 3 2. Electronic caliper Codimex E1... 4 2.1 Technical specifications... 4 2.2 Meaning
More informationOPERATING INSTRUCTIONS:
List OPERATING INSTRUCTIONS: Preparation For Installation, Product Identification Charging The Batteries ing And Adjusting The Lift Mounting Head s Brackets Mounting Clamps And Quick-Locking Arms Installation
More informationPulse. Multisport HR Fitness Tracker. Quick Start Guide. delvfire.com. ID115Plus HR
Pulse Multisport HR Fitness Tracker Quick Start Guide ID115Plus HR delvfire.com Register your new Delvfire product and claim... 1 Year free warranty The easy way to register - simply visit: www.delvfire.com/warranty
More informationUser's Guide. EasyView K-Type Thermometer. Model EA11A
User's Guide EasyView K-Type Thermometer Model EA11A Introduction Congratulations on your purchase of the Extech EasyView Thermometer. This device offers a single K-type thermocouple input with multifunction
More informationInstruction Manual. Electronic Self-Leveling Dual Grade Horizontal / Vertical Rotary Laser Model No
6274H-1_Manuals 9/26/12 10:44 AM Page 1 Electronic Self-Leveling Dual Grade Horizontal / Vertical Rotary Laser Model No. 40-6582 Instruction Manual Congratulations on your choice of this Electronic Self-Leveling
More informationSelf-leveling Laser Marker (4V1HXL)
Self-leveling Laser Marker (4V1HXL) Congratulations on your choice of this Self-leveling Laser Marker. For the purpose of long-term use of this instrument, we suggest you to read this instruction manual
More informationINSTRUCTION MANUAL CAT ecount
Electron Microscopy Sciences INSTRUCTION MANUAL CAT. 70309-01 ecount Safety precautions The ecount is used specifically in bioscience, medical, and chemistry laboratories. It may come in contact with biohazardous
More informationTablet PA752C. User Manual
Tablet PA752C User Manual User Manual Notice Before operating the device, please read the safety precautions and user s guide carefully to ensure safe and proper usage. The descriptions in this user s
More informationDP-152. Digital Picture Viewer. Instruction Manual. Please read this manual carefully before operation 152SX
DP-152 Digital Picture Viewer Instruction Manual Please read this manual carefully before operation 152SX Precautions For Customer Use: Enter below the serial number that is located on the bottom of the
More informationHeight Gauges Pages Data Processing Height Gauges Pages
Height Gauges Height Gauges Pages 232-240 Data Processing Height Gauges Pages 241-244 for sale to the United Kingdom only. All products are intended to be sold to coercial customers. Therefore VAT is not
More informationOWNER S MANUAL 9908-TE. HIGH PRECISION AUTO-RANGING DC/True RMS AC BENCH-TOP DIGITAL MULTIMETER
OWNER S MANUAL 9908-TE HIGH PRECISION AUTO-RANGING DC/True RMS AC BENCH-TOP DIGITAL MULTIMETER IMPORTANT! Read and understand this manual before using the instrument. Failure to understand and comply with
More informationCF3000 Dealer Diagnostic Tool Instruction Manual
CF3000 Dealer Diagnostic Tool Instruction Manual Table of Contents: About the CF3000......3 Important Precautions......4 Components....5 Charging the CF3000......7 Licensing the CF3000.......8 Updating
More informationQuick Start Guide. SupraPad i1000qw. 10.1" Windows Tablet
SupraPad i1000qw Quick Start Guide NOTE: For Spanish users, please go to Control Panel", then go to Clock, Language, and Region", then go to Language to change from English to Spanish Language OSD. 10.1"
More informationSAC / SHC / SHC-CH SERIES
This document hosted by: www.oldwillknottscales.com SAC / SHC / SHC-CH SERIES HIGH PRECISION COUNTING SCALE OPERATION MANUAL PLEASE READ THIS MANUAL VERY CAREFULLY BEFORE ATTEMPT TO OPERATE THE SCALE July
More informationProntoPro Intelligent Remote Control. User Guide
ProntoPro Intelligent Remote Control User Guide Table of Content Taking a First Look... 3 Intelligent Remote Control... 3 Before You Start... 5 Getting Started... 7 Activating the Remote Control... 7 Defining
More informationMulti-Function Smart Indicator User Manual
Multi-Function Smart Indicator User Manual EC30006 Content 1 Notice... 2 2 Specification... 2 3 Main parameter... 3 4 How to fix... 3 5 Port... 4 6 On/Off... 4 7 Charging... 4 8 Display... 5 9 Screen keypad...
More information