PN7. Communication. Features. Device variant. Copyright 2015, Builder: , Time: 04:31:57

Transcription

1 Version V2.2.4 Release date Copyright 215, Builder: , Time: 4:31:57 PN7 Vendor ID Device ID Vendor name Vendor text Vendor URL 31 / x136 - Bytes: 1 54 / x1 x / x137 - Bytes: 1 55 / x x1 x37 ifm electnic gmbh Communication IO-Link revision Bit rate Minimum cycle time SIO mode supported Features Block parametrization Data storage V1.1 COM2 2.3 ms Yes Yes Yes Device variant PN74 PE74 Electnic pressure monitor, , Pcess connection G 1/4 I Electnic pressure monitor, , Pcess connection G 1/4 I, Sealing EPDM PN14A Electnic pressure monitor, , Appval ATEX, Pcess connection G 1/4 I Page 1

2 Page 2

3 Pcess data (Pcess data input) Total bit length = 16 Description Bit length Pressure Current pressure to 3 (OL) -1 to 15.1 Switchstate [OUT2]. State depends on [OU2] (false) inactive (true) active Switchstate [OUT1]. State depends on [OU1] (false) inactive (true) active Page 3

4 Standard Command 2 wo (13) Restore Factory Settings (24) IO-Link 1.1 system test command 24, Event 8DFE will appear (241) IO-Link 1.1 system test command 241, Event 8DFE will disappear (242) IO-Link 1.1 system test command 242, Event 8DFF will appear (243) IO-Link 1.1 system test command 243, Event 8DFF will disappear (255) Command without effect, for internal use only Device Locks 12 RecordT Data Storage bitoffs 1 1 Bit () (false) Unlocked (true) Locked Local User Interface bitoffs 3 1 Bit () (false) Unlocked (true) Locked Vendor 16 ifm electnic gmbh Vendor Text 17 Pduct 18 Pduct ID 19 Pduct Text 2 Electnic pressure monitor Page 4

5 Serial Number Hardware Version 22 Firmware Version 23 Application Specific Tag 24 max 16 Byte SP1 rp1 Switch point 1, [SP1] shall be greater than [rp1]. Please consider to the actual [rp1] value. If the [SP1] will be set below [rp1] it will be refused to 1.1 Reset point 1, [rp1] shall be smaller than [SP1]. Please consider to the actual [SP1] value. If the [rp1] will be set above [SP1] it will be refused to OU1 Output configuration [OUT 1] 67 (3) Hno / Hysteresis fct normally open (3) Hno / Hysteresis fct normally open (4) Hnc / Hysteresis fct normally closed (5) Fno / Window fct normally open (6) Fnc / Window fct normally closed SP2 rp2 Switch point 2, [SP2] shall be greater than [rp2]. Please consider to the actual [rp2] value. If the [SP2] will be set below [rp2] it will be refused to 1.1 Reset point 2, [rp2] shall be smaller than [SP2]. Please consider to the actual [SP2] value. If the [rp2] will be set above [SP2] it will be refused to Page 5

6 OU2 Output configuration [OUT 2] 7 (3) Hno / Hysteresis fct normally open (3) Hno / Hysteresis fct normally open (4) Hnc / Hysteresis fct normally closed (5) Fno / Window fct normally open (6) Fnc / Window fct normally closed (13) desi / Diagnosis output Uni Selection of unit on the sensor display 72 () () (1) MPa (2) PSI HI Maximum memory value to 3 (OL) -1 to 15 LO Minimum memory value to 3 (OL) -1 to 15 ds1 Switch-On delay [OUT 1] 77 to 5.1 s dr1 Switch-OFF delay [OUT 1] 78 to 5.1 s ds2 Switch-On delay [OUT 2] 79 to 5.1 s Page 6

7 dr2 Switch-OFF delay [OUT 2] 8 to 5.1 s P-n Output polarity for the switching outputs 81 () PnP () PnP (1) npn dap Response time between pcess value change and change of the switching output 82 (5) 6 ms () 3 ms (1) 6 ms (2) 1 ms (3) 17 ms (4) 3 ms (5) 6 ms (6) 125 ms (7) 25 ms (8) 5 ms dis Display settings 83 RecordT Display On / OFF bitoffs 7 1 Bit (false) On (false) On (true) OFF Display orientation bitoffs 6 1 Bit (false) Not tated (false) Not tated (true) Rotated 18 Update rate bitoffs 6 Bit (2) d2 / medium (1) d1 / fast (2) d2 / medium (4) d3 / slow HIPP High pressure peak to 3.1 Page 7

8 HIPS Configuration of overload counter switch point to 2.1 HIPC Overload counter 89 to Loc [Loc] locks the local user interface to prevent unintentional changes, [Loc] is resettable at the device 95 (1) uloc / unlocked () Loc / locked (1) uloc / unlocked Commands Performs action on the sensor 241 wo (247) Reset [HI] memory (246) Reset [LO] memory (49) Reset high pressure peak [HIPP] (5) Reset overload counter [HIPC] Events Code Type Description d / 8C 1 h Pcess variable range over-run Warning Pcess data uncertain. Note: This Event will not be transmitted via IO-Link Event mechanism. It is only available by reading 37 (DetailedDeviceStatus) oder 545 (BitCoded_ActiveEvents) d / 8C 3 h Pcess variable range under-run Warning Pcess data uncertain. Note: This Event will not be transmitted via IO-Link Event mechanism. It is only available by reading 37 (DetailedDeviceStatus) oder 545 (BitCoded_ActiveEvents) 3635 d / 8D FE h Test Event 1 Warning Event appears by setting index 2 to value 24, Event disappears by setting index 2 to value d / 8D FF h Test Event 2 Warning Event appears by setting index 2 to value 242, Event disappears by setting index 2 to value 243 Page 8

9 Err types Err code d / 8 h d / 8 11 h d / 8 12 h 328 d / 8 2 h 3283 d / 8 23 h d / 8 3 h d / 8 33 h 3282 d / 8 34 h d / 8 35 h d / 8 36 h d / 8 4 h d / 8 41 h d / 8 82 h 3325 d / 81 1 h 3326 d / 81 2 h Device application err - no details not available not available Service temporarily not available denied Parameter value out of range Parameter length overrun Parameter length underrun Function not available Function temporarily unavailable Invalid parameter set Inconsistent parameter set Application not ready Parameter hidden Parameter currently not available Description Service has been refused by the device application and no detailed information of the incident is available occurs to a not existing index occurs to a not existing subindex Parameter is not accessible due to the current state of the device application Write access on a read-only parameter Written parameter value is outside its permitted value range Written parameter length is above its predefined length Written parameter length is below its predefined length Written command is not supported by the device application Written command is not available due to the current state of the device application Written single parameter collides with other actual parameter settings Parameter inconsistencies were found at the end of block parameter transfer, device plausibility check failed Read or write service is refused due to a temporarily unavailable application Page 9