PV7. Communication. Features. Device variant. Copyright 2016, Builder: , Time: 02:58:01

Transcription

1 Verion V Releae date Copyright 216, Builder: , Time: 2:58:1 PV7 Vendor ID Device ID Vendor name Vendor text Vendor URL 31 / x136 - : 1 54 / x1 x / x2c9 - : 2 21 / x x2 xc9 ifm electnic gmbh Communication IO-Link reviion Bit rate Minimum cycle time SIO mode upported Feature Block parametrization Data torage V1.1 COM2 5. m Ye Ye Ye Device variant PV74 Electnic preure witch, , IO-Link, culu, G 1/4 A / M5 I nach ISO Page 1

2 Pce data (Pce data input) Total bit length = 32 Bit offet Bit length Preure Current preure to 15 (3276) OL (32764) NoData.1 OUT2 Statu depend on [OU2] 1 (fale) inactive (true) active OUT1 Statu depend on [OU1] (fale) inactive (true) active Page 2

3 Standard Command 2 wo (13) Retore Factory Setting (161) Reet [Hi] and [Lo] memory (162) Reet [Lo] memory (163) Reet [Hi] memory (169) Reet overload counter [HIPC] (24) IO-Link 1.1 ytem tet command 24, Event 8DFE appear (241) IO-Link 1.1 ytem tet command 241, Event 8DFE diappear (242) IO-Link 1.1 ytem tet command 242, Event 8DFF appear (243) IO-Link 1.1 ytem tet command 243, Event 8DFF diappear (255) Command without effect, for internal ue only Device Lock 12 RecordT Data Storage bitoff 1 (fale) (fale) Unlocked Page 3

4 Device Lock 12 RecordT (true) Locked Vendor 16 max 19 ifm electnic gmbh Vendor Text 17 max 11 Pduct 18 max 6 PV74 Pduct ID 19 max 6 PV74 Pduct Text 2 max 26 Electnic preure enor Serial Number 21 max 12 Hardware Verion 22 max 2 Firmware Verion 23 max 5 Application Specific Tag 24 max 32 *** Device Statu 36 () Device i OK () Device i OK (1) Maintenance required (2) Out of pecification (3) Functional check Page 4

5 Device Statu 36 () Device i OK (4) Failure 5 to 255 (Reerved) Detailed Device Statu h P-n Output polarity for the witching output 5 () PnP () PnP (1) npn dap Damping of the meaured ignal 51 6 to 4.1 BitCoded_ActiveEvent Bit mak for current pending event 545 RecordT 32 Bit Bit_31 Bit 31 indicate the aigned bitoff 31 () noev () noev (1) x8dff Bit_3 Bit 3 indicate the aigned bitoff 3 () noev () noev (1) x8dfe Bit_9 Bit 9 indicate the aigned bitoff 9 () noev () noev (1) x8c3 Bit_8 Bit 8 indicate the aigned bitoff 8 () noev () noev (1) x8c1 Bit_2 Bit 2 indicate the aigned bitoff 2 () noev () noev (1) x771 Bit_1 Bit 1 indicate the aigned bitoff 1 () noev () noev (1) x632 Bit_ Bit indicate the aigned bitoff () noev () noev (1) x5 ParaConfigFaultCollection Diplay the wngly et parameter 546 Page 5

6 uni Selection of the phyical unit 551 (1) () MPa (1) (2) pi Hi Maximum memory value 56 ().1-1 to 15 (3276) OL (32764) NoData Lo Minimum memory value 561 ().1-1 to 15 (3276) OL (32764) NoData ou1 Output configuration [OUT 1] 58 (3) Hno / Hyterei fct normally open (3) Hno / Hyterei fct normally open (4) Hnc / Hyterei fct normally cloed (5) Fno / Window fct normally open (6) Fnc / Window fct normally cloed ds1 Switching delay for [OUT 1] 581 to 5.1 dr1 Reet delay for [OUT 1] 582 to 5.1 SP_FH1 Switch point 1, [SP1] mut be greater than [rp1]. Pleae take into account the current [rp1] to 1.1 Page 6

7 value. [SP1] will be refued if below [rp1]. [SP] = [FH] and [rp] = [FL] if [OU1] = Fno, Fnc rp_fl1 Reet point 1, [rp1] mut be 584 maller than [SP1]. Pleae take into account the current [SP1] value.i[rp1] will be refued if above [SP1]. [rp] = [FL] and [SP] = [FH] if [OU1] = Fno, Fnc to ou2 Output configuration [OUT 2] 59 (3) Hno / Hyterei fct normally open (3) Hno / Hyterei fct normally open (4) Hnc / Hyterei fct normally cloed (5) Fno / Window fct normally open (6) Fnc / Window fct normally cloed ds2 Switching delay for [OUT 2] 591 to 5.1 dr2 Reet delay for [OUT 2] 592 to 5.1 SP_FH2 Switch point 2, [SP2] mut be 593 greater than [rp2]. Pleae take into account the current [rp2] value. [SP2] will be refued if below [rp2]. [SP] = [FH] and [rp] = [FL] if [OU2] = Fno, Fnc 75-9 to 1.1 rp_fl2 Reet point 2, [rp2] mut be maller than [SP2]. Pleae take into account the current to Page 7

8 [SP2] value.i[rp2] will be refued if above [SP2]. [rp] = [FL] and [SP] = [FH] if [OU2] = Fno, Fnc cof Ze-point calibration (Calibration offet) 51-5 to 5.1 % HIPS Configuration of overload counter witch point to 1.1 HIPC Overload counter Bit to Event Code Type 248 d / 5 h Device hardware fault Err Device Exchange d / 63 2 h Parameter err Err Check data heet and value 348 d / 77 1 h Short circuit Err Check intallation d / 8C 1 h Pce variable range over-run Warning Pce data uncertain. Note: Thi Event will not be tranmitted via IO-Link Event mechanim. It i only available by reading 37 (DetailedDeviceStatu) oder 545 (BitCoded_ActiveEvent) d / 8C 3 h Pce variable range under-run Warning Pce data uncertain. Note: Thi Event will not be tranmitted via IO-Link Event mechanim. It i only available by reading 37 (DetailedDeviceStatu) oder 545 (BitCoded_ActiveEvent) 3635 d / 8D FE h Tet Event 1 Warning Event appear by etting index 2 to value 24, Event diappear by etting index 2 to value d / 8D FF h Tet Event 2 Warning Event appear by etting index 2 to value 242, Event diappear by etting index 2 to value 243 Err type Err code d / 8 h d / 8 11 h Device application err - no detail not available Service ha been refued by the device application and no detailed information of the incident i available occur to a not exiting index Page 8

9 Err type Err code d / 8 12 h 328 d / 8 2 h 3283 d / 8 23 h d / 8 3 h d / 8 33 h 3282 d / 8 34 h d / 8 35 h d / 8 36 h d / 8 4 h d / 8 41 h d / 8 82 h not available Service temporarily not available denied Parameter value out of range Parameter length overrun Parameter length underrun Function not available Function temporarily unavailable Invalid parameter et Inconitent parameter et Application not ready occur to a not exiting ubindex Parameter i not acceible due to the current tate of the device application Write acce on a read-only parameter Written parameter value i outide it permitted value range Written parameter length i above it predefined length Written parameter length i below it predefined length Written command i not upported by the device application Written command i not available due to the current tate of the device application Written ingle parameter collide with other actual parameter etting Parameter inconitencie were found at the end of block parameter tranfer, device plauibility check failed Read or write ervice i refued due to a temporarily unavailable application Page 9