Communication. Features. Device variant. Copyright 2015, Builder: , Time: 09:23:27

Transcription

1 Version V.3.3. Release date Copyright 25, Builder: , Time: 9:23:27 SB Vendor ID Device ID Vendor name Vendor text Vendor URL 3 / x36 - s: 54 / x x36 56 / x23 - s: 2 49 / x x2 x3 ifm electnic gmbh Communication IO-Link revision Bit rate Minimum cycle time SIO mode supported Features Block parametrization Data storage V. COM2 3.2 ms Yes Yes Yes Device variant SBY233 SBG233 Flow sensor,..25, IO-Link, Rp 3/4 Flow sensor,..25, IO-Link, G /2 Page

2 Pcess data (Pcess data input) Total bit length = 32 Bit offset Bit length Flow Current flow 6 6 (3) OL to 25. Temperature Current temperature 2 4 (23) OL - to 22 (-33) UL OUT2 Status depends on [OU2] (false) inactive (true) active OUT Status depends on [OU] (false) inactive (true) active Page 2

3 Standard Command 2 wo (3) Restore Factory Settings (65) Reset [Hi.T] and [Lo.T] memory (66) Reset [Lo.T] memory (67) Reset [Hi.T] memory (24) IO-Link. system test command 24, Event 8DFE appears (24) IO-Link. system test command 24, Event 8DFE disappears (242) IO-Link. system test command 242, Event 8DFF appears (243) IO-Link. system test command 243, Event 8DFF disappears (255) Command without effect, for internal use only Device Locks 2 RecordT Data Storage bitoffs Bit (false) (false) Unlocked (true) Locked Local User Interface bitoffs 3 Bit (false) (false) Unlocked Page 3

4 Device Locks 2 RecordT (true) Locked Vendor 6 max 9 ifm electnic gmbh Vendor Text 7 max Pduct 8 max 6 Pduct ID 9 max 6 Pduct Text 2 max 23 Mechatnic flow sensor Serial Number 2 max 2 Hardware Version 22 max 2 Firmware Version 23 max 5 Application Specific Tag 24 max 32 *** Device Status 36 () Device is OK Detailed Device Status h P-n Output polarity for the switching outputs 5 () PnP () PnP () npn Page 4

5 dap Damping of the measured signal 5 to 5. s daa Response time between pcess value change and change of the analog output 52 to 5. s SEL Selection of the measurand for the evaluation via [OUT ] 52 () FLOW () FLOW (2) TEMP SEL2 Selection of the measurand for the evaluation via [OUT 2] 52 () FLOW () FLOW (2) TEMP FOU [OUT ] behaviour in case of fault 53 () OU () OU (2) On (4) OFF FOU2 [OUT 2] behaviour in case of fault 532 () OU () OU (2) On (4) OFF uni Selection of unit on the sensor display 55 () () () m³/h Page 5

6 dis Display settings 552 RecordT Display On / OFF bitoffs 7 Bit (false) On (false) On (true) OFF Display orientation bitoffs 6 Bit (false) Not tated (false) Not tated (true) Rotated 8 Update rate bitoffs 6 Bit (2) d2 / medium () d / fast (2) d2 / medium (4) d3 / slow SELd Selection of measurement on the sensor display 553 RecordT Displayed measurement bitoffs 5 Bit () FLOW () FLOW (2) TEMP colr Assignment of the display colours 'red' and 'green' within the measuring range 554 (2) red / Display colour red (independent of the measured value) (2) red / Display colour red (independent of the measured value) (3) GrEn / Display colour green (independent of the measured value) (4) rou / Display colour red when OUT switches (5) Gou / Display colour green when OUT switches Page 6

7 colr Assignment of the display colours 'red' and 'green' within the measuring range 554 (2) red / Display colour red (independent of the measured value) (6) r2ou / Display colour red when OUT2 switches (7) G2ou / Display colour green when OUT2 switches Hi.T Maximum memory value for temperature 562 () Lo.T Minimum memory value for temperature 563 () ou Output configuration [OUT ] 58 (3) Hno / Hysteresis fct normally open (3) Hno / Hysteresis fct normally open (4) Hnc / Hysteresis fct normally closed (5) Fno / Window fct normally open (6) Fnc / Window fct normally closed (7) FRQ / Frequency output SP_FH_FLOW Switch point / Flow, [SP] 583 must be greater than [rp]. Please take into account the current [rp] value. [SP] will be refused if below [rp]. [SP] 5 2 to 25. Page 7

8 = [FH] and [rp] = [FL] if [OU] = Fno, Fnc. rp_fl_flow Reset point / Flow, [rp] 584 must be smaller than [SP]. Please take into account the current [SP] value.i[rp] will be refused if above [SP]. [rp] = [FL] and [SP] = [FH] if [OU] = Fno, Fnc. 48 to 248. SP_FH_TEMP Switch point / Temperature, 585 [SP] must be greater than [rp]. Please take into account the current [rp] value. [SP] will be refused if below [rp]. [SP] = [FH] and [rp] = [FL] if [OU] = Fno, Fnc. 2-9 to rp_fl_temp Reset point / Temperature, [rp] must be smaller than [SP]. Please take into account the current [SP] value.i[rp] will be refused if above [SP]. [rp] = [FL] and [SP] = [FH] if [OU] = Fno, Fnc to 99 ou2 Output configuration [OUT 2] 59 () I / Analog signal 4 2 ma () I / Analog signal 4 2 ma (3) Hno / Hysteresis fct normally open (4) Hnc / Hysteresis fct normally closed Page 8

9 ou2 Output configuration [OUT 2] 59 () I / Analog signal 4 2 ma (5) Fno / Window fct normally open (6) Fnc / Window fct normally closed SP_FH2_FLOW Switch point 2 / Flow, [SP2] 593 must be greater than [rp2]. Please take into account the current [rp2] value. [SP2] will be refused if below [rp2]. [SP] = [FH] and [rp] = [FL] if [OU2] = Fno, Fnc. 2 to 25. rp_fl2_flow Reset point 2 / Flow, [rp2] 594 must be smaller than [SP2]. Please take into account the current [SP2] value.i[rp2] will be refused if above [SP2]. [rp] = [FL] and [SP] = [FH] if [OU2] = Fno, Fnc. 98 to 248. SP_FH2_TEMP Switch point 2 / Temperature, 595 [SP2] must be greater than [rp2]. Please take into account the current [rp2] value. [SP2] will be refused if below [rp2]. [SP] = [FH] and [rp] = [FL] if [OU2] = Fno, Fnc to rp_fl2_temp Reset point 2 / Temperature, [rp2] must be smaller than [SP2]. Please take into account the current [SP2] value.i[rp2] will be refused if above [SP2]. [rp] = [FL] and to 99 Page 9

10 [SP] = [FH] if [OU2] = Fno, Fnc. MEdI Medium selection 682 () H2O () H2O () OIL (2) OIL.2 FEP_FLOW Flow on [OUT] at [FrP] to 25. FSP_TEMP Temperature on [OUT] at Hz to 78 FEP_TEMP Temperature on [OUT] at [FrP] to FrP Absolute frequency maximum 76 for [OUT ] to. khz Events Code Type 248 d / 5 h Device hardware fault Err Device Exchange d / 63 2 h Parameter err Err Check data sheet and values 348 d / 77 h Short circuit Err Check installation d / 8C h Pcess variable range over-run Warning Pcess data uncertain d / 8C 3 h Pcess variable range under-run Warning Pcess data uncertain 3594 d / 8C 4 h Maintenance required - Cleaning Notification Clean device 3635 d / 8D FE h Test Event Warning Event appears by setting index 2 to value 24, Event disappears by setting index 2 to value d / 8D FF h Test Event 2 Warning Event appears by setting index 2 to value 242, Event disappears by setting index 2 to value 243 Page

11 Err types Err code d / 8 h d / 8 h d / 8 2 h 328 d / 8 2 h 3283 d / 8 23 h 3286 d / 8 3 h 3289 d / 8 33 h 3282 d / 8 34 h 3282 d / 8 35 h d / 8 36 h d / 8 4 h d / 8 4 h d / 8 82 h Device application err - no details not available not available Service temporarily not available denied Parameter value out of range Parameter length overrun Parameter length underrun Function not available Function temporarily unavailable Invalid parameter set Inconsistent parameter set Application not ready Service has been refused by the device application and no detailed information of the incident is available occurs to a not existing index occurs to a not existing subindex Parameter is not accessible due to the current state of the device application Write access on a read-only parameter Written parameter value is outside its permitted value range Written parameter length is above its predefined length Written parameter length is below its predefined length Written command is not supported by the device application Written command is not available due to the current state of the device application Written single parameter collides with other actual parameter settings Parameter inconsistencies were found at the end of block parameter transfer, device plausibility check failed Read or write service is refused due to a temporarily unavailable application Page