Communication. Features. Device variant. Copyright 2016, Builder: , Time: 04:59:44

Size: px

Start display at page:

Marjory Briggs
5 years ago
Views:

-11-3 Copyright 216, Builder: 3.1.1.2, Time: 4:59:44 SM Vendor ID Device ID Vendor name Vendor text Vendor URL 31 / x136 - s: 1 54 / x1 x36 575 /

1 Version V Release date Copyright 216, Builder: , Time: 4:59:44 SM Vendor ID Device ID Vendor name Vendor text Vendor URL 31 / x136 - s: 1 54 / x1 x / x23f - s: 2 63 / x x2 x3f ifm electnic gmbh Communication IO-Link revision Bit rate Minimum cycle time SIO mode supported Features Block parametrization Data storage V1.1 COM2 5. ms Yes Yes Yes Device variant SM8 SM81 SM84 SM85 Flow sensor, , G 1 Flow sensor, , G 1 Flow sensor, , Rc 1" Flow sensor, , Rc 1" Page 1

Pcess data (Pcess data input) Total bit length = 64 Bit offset Bit length Totalizer Quantity meter which continuously totals the volumetric flow since the last reset Float32T 32-999999999.

2 Pcess data (Pcess data input) Total bit length = 64 Bit offset Bit length Totalizer Quantity meter which continuously totals the volumetric flow since the last reset Float32T to l Flow Current flow to 12 (-32762) cr.ul (-3276) UL (3276) OL (32762) cr.ol.1 Temperature Current temperature to 1 (-8186) cr.ul (-8184) UL (8184) OL (8186) cr.ol.1 C OUT2 Status depends on [OU2] 1 (false) inactive (true) active OUT1 Status depends on [OU1] (false) inactive (true) active Page 2

3 Page 3

4 Standard Command 2 wo (13) Restore Factory Settings (161) Reset [Hi.F] and [Lo.F] memory (162) Reset [Lo.F] memory (163) Reset [Hi.F] memory (164) Reset Totalizer (165) Reset [Hi.T] and [Lo.T] memory (166) Reset [Lo.T] memory (167) Reset [Hi.T] memory (24) IO-Link 1.1 system test command 24, Event 8DFE appears (241) IO-Link 1.1 system test command 241, Event 8DFE disappears (242) IO-Link 1.1 system test command 242, Event 8DFF appears (243) IO-Link 1.1 system test command 243, Event 8DFF disappears Page 4

5 Standard Command 2 wo (255) Command without effect, for internal use only Device Locks 12 RecordT Data Storage bitoffs 1 (false) (false) Unlocked (true) Locked Local User Interface bitoffs 3 (false) (false) Unlocked (true) Locked Vendor 16 max 19 ifm electnic gmbh Vendor Text 17 max 11 Pduct 18 max 6 Pduct ID 19 max 6 Pduct Text 2 max 29 Magnetic- inductive flow meter Serial Number 21 max 12 Hardware Version 22 max 2 Firmware Version 23 max 5 Application Specific Tag 24 max 32 *** Page 5

6 Device Status 36 () Device is OK () Device is OK (1) Maintenance required (2) Out of specification (3) Functional check (4) Failure 5 to 255 (Reserved) Detailed Device Status h P-n Output polarity for the switching outputs 5 () PnP () PnP (1) npn dap Damping of the measured signal 51 6 to 5.1 s SEL2 Selection of the measurand for the evaluation via [OUT 2] 521 (1) FLOW (1) FLOW (2) TEMP FOU1 [OUT 1] behaviour in case of fault 531 (4) OFF (1) OU (2) On (4) OFF FOU2 [OUT 2] behaviour in case of fault 532 (4) OFF Page 6

7 FOU2 [OUT 2] behaviour in case of fault 532 (4) OFF (1) OU (2) On (4) OFF BitCoded_ActiveEvents Bit mask for current pending events 545 RecordT 32 Bit Bit_31 Bit 31 indicates the assigned bitoffs 31 () noev () noev (1) x8dff Bit_3 Bit 3 indicates the assigned bitoffs 3 () noev () noev (1) x8dfe Bit_16 Bit 16 indicates the assigned bitoffs 16 () noev () noev (1) x8c2 Bit_9 Bit 9 indicates the assigned bitoffs 9 () noev () noev (1) x8c3 Bit_8 Bit 8 indicates the assigned bitoffs 8 () noev () noev (1) x8c1 Bit_2 Bit 2 indicates the assigned bitoffs 2 () noev () noev (1) x771 Bit_1 Bit 1 indicates the assigned bitoffs 1 () noev () noev (1) x632 Bit_ Bit indicates the assigned bitoffs () noev () noev (1) x5 ParaConfigFaultCollection Displays the wngly set parameters 546 Loc [Loc] locks the local user interface to prevent unintentional changes, [Loc] is resettable at the device 55 (1) uloc () Loc Page 7

8 Loc [Loc] locks the local user interface to prevent unintentional changes, [Loc] is resettable at the device 55 (1) uloc (1) uloc uni Selection of the physical unit 551 () () (1) m³/h dis Display settings 552 RecordT Display On / OFF bitoffs 7 (false) On (false) On (true) OFF Display orientation bitoffs 6 (false) Not tated (false) Not tated (true) Rotated 18 Update rate bitoffs 6 Bit (4) d3 / slow (1) d1 / fast (2) d2 / medium (4) d3 / slow SELd Selection of measurement on the sensor display 553 RecordT Displayed measurement bitoffs 15 Bit (1) FLOW (1) FLOW (2) TEMP (4) TOTL Hi.F Maximum memory value for flow 56 ().1-12 to 12 (-32762) cr.ul (-3276) UL (3276) OL (32762) cr.ol Page 8

9 Lo.F Minimum memory value for flow 561 () -12 to 12 (-32762) cr.ul (-3276) UL (3276) OL (32762) cr.ol.1 Hi.T Maximum memory value for temperature 562 ().1 C -4 to 1 (-8186) cr.ul (-8184) UL (8184) OL (8186) cr.ol Lo.T Minimum memory value for temperature 563 ().1 C -4 to 1 (-8186) cr.ul (-8184) UL (8184) OL (8186) cr.ol ou1 Output configuration [OUT 1] 58 (3) Hno / Hysteresis fct normally open (3) Hno / Hysteresis fct normally open (4) Hnc / Hysteresis fct normally closed Page 9

10 ou1 Output configuration [OUT 1] 58 (3) Hno / Hysteresis fct normally open (5) Fno / Window fct normally open (6) Fnc / Window fct normally closed (9) ImP / Impulse output (26) dir.f / Flow direction, active in direction [Fdir] SP1_FLOW Switch point 1 / Flow, [SP1] 583 must be greater than [rp1]. Please take into account the current [rp1] value. [SP1] will be refused if below [rp1] 2 7 to 1.1 rp1_flow Reset point 1 / Flow, [rp1] 584 must be smaller than [SP1]. Please take into account the current [SP1] value. [rp1] will be refused if above [SP1] to ou2 Output configuration [OUT 2] 59 (1) I / Analog signal 4 2 ma (1) I / Analog signal 4 2 ma (2) U / Analog signal...1 V (3) Hno / Hysteresis fct normally open (4) Hnc / Hysteresis fct normally closed Page 1

11 ou2 Output configuration [OUT 2] 59 (1) I / Analog signal 4 2 ma (5) Fno / Window fct normally open (6) Fnc / Window fct normally closed (14) In.D / Digital input (26) dir.f / Flow direction, active in direction [Fdir] SP2_FLOW Switch point 2 / Flow, [SP2] 593 must be greater than [rp2]. Please take into account the current [rp2] value. [SP2] will be refused if below [rp2] 4 7 to 1.1 rp2_flow Reset point 2 / Flow, [rp2] 594 must be smaller than [SP2]. Please take into account the current [SP2] value. [rp2] will be refused if above [SP2] to SP2_TEMP Switch point 2 / Temperature, 595 [SP2] must be greater than [rp2]. Please take into account the current [rp2] value. [SP2] will be refused if below [rp2] to 8.1 C rp2_temp Reset point 2 / Temperature, [rp2] must be smaller than [SP2]. Please take into account the current [SP2] value. [rp2] will be refused if above [SP2] to C Page 11

12 ASP2_FLOW Analogue start point 2 / Flow. [ASP2] must be smaller than [AEP2]. Please take into account the current [AEP2]. For info on the minimum hysteresis [AEP2]-[ASP2] please refer to the operating instructions 63 to 8.1 AEP2_FLOW Analogue end point 2 / Flow. 631 [AEP2] must be greater than [ASP2]. Please take into account the current [ASP2]. For info on the min hysteresis [AEP2]-[ASP2] please refer to the operating instructions 1 2 to 1.1 ASP2_TEMP Analogue start point 2 / 632 Temperature. [ASP2] must be smaller than [AEP2]. Please take into account the current [AEP2]. For info on the minimum hysteresis [AEP2]-[ASP2] please refer to the operating instructions -2-2 to 6.1 C AEP2_TEMP Analogue end point 2 / 633 Temperature. [AEP2] must be greater than [ASP2]. Please take into account the current [ASP2]. For info on the min hysteresis [AEP2]-[ASP2] please refer to the operating instructions 8 to 8.1 C DIn2 Configuration of digital input (Pin 2) 676 (2) +EDG () HIGH Page 12

13 DIn2 Configuration of digital input (Pin 2) 676 (2) +EDG (1) LOW (2) +EDG (3) -EDG rto Meter reset mode 32 RecordT [OFF] = Manual reset / [Time] = Time contlled reset bitoffs 15 (true) OFF (false) Time (true) OFF Meter reset time: coarse adjustment bitoffs 8 3 Bit (1) hours (1) hours (2) days (4) weeks Meter reset time: fine adjustment. Allowed max values for [Time] are 23 hours or 6 days or 8 weeks bitoffs (1) 1 (1) 1 (2) 2 (3) 3 (4) 4 (5) 5 (6) 6 (7) 7 (8) 8 (9) 9 (1) 1 (11) 11 (12) 12 (13) 13 (14) 14 (15) 15 (16) 16 (17) 17 (18) 18 Page 13

14 rto Meter reset mode 32 RecordT (19) 19 (2) 2 (21) 21 (22) 22 (23) 23 dst Delay Startup 33 to 5.1 s ImPS Pulse value 34 Float32T.1.1 to 1 1 l ImPR Pulse repetition active (= pulse output) or not active (= function preset meter) 35 (1) YES (1) YES () no LFC Low flow cutoff to 2.1 FP Totalizer counting rule 311 (1) + () -+ (1) + Fdir Preferred direction of flow for the totaliser 312 () + () + (1) - TOTL_M Consumed quantity before the last reset 314 Float32T to l Page 14

15 Events Code Type 248 d / 5 h Device hardware fault Err Device Exchange d / 63 2 h Parameter err Err Check data sheet and values 348 d / 77 1 h Short circuit Err Check installation d / 8C 1 h Pcess variable range over-run Warning Pcess data uncertain. Note: This Event will not be transmitted via IO-Link Event mechanism. It is only available by reading 37 (DetailedDeviceStatus) oder 545 (BitCoded_ActiveEvents) d / 8C 3 h Pcess variable range under-run Warning Pcess data uncertain. Note: This Event will not be transmitted via IO-Link Event mechanism. It is only available by reading 37 (DetailedDeviceStatus) oder 545 (BitCoded_ActiveEvents) d / 8C 2 h Measurement range over-run Err Check application 3635 d / 8D FE h Test Event 1 Warning Event appears by setting index 2 to value 24, Event disappears by setting index 2 to value d / 8D FF h Test Event 2 Warning Event appears by setting index 2 to value 242, Event disappears by setting index 2 to value 243 Err types Err code d / 8 h d / 8 11 h d / 8 12 h 328 d / 8 2 h 3283 d / 8 23 h d / 8 3 h d / 8 33 h 3282 d / 8 34 h d / 8 35 h d / 8 36 h d / 8 4 h d / 8 41 h d / 8 82 h Device application err - no details not available not available Service temporarily not available denied Parameter value out of range Parameter length overrun Parameter length underrun Function not available Function temporarily unavailable Invalid parameter set Inconsistent parameter set Application not ready Service has been refused by the device application and no detailed information of the incident is available occurs to a not existing index occurs to a not existing subindex Parameter is not accessible due to the current state of the device application Write access on a read-only parameter Written parameter value is outside its permitted value range Written parameter length is above its predefined length Written parameter length is below its predefined length Written command is not supported by the device application Written command is not available due to the current state of the device application Written single parameter collides with other actual parameter settings Parameter inconsistencies were found at the end of block parameter transfer, device plausibility check failed Read or write service is refused due to a temporarily unavailable application Page 15

Communication. Features. Device variant. Copyright 2017, Builder: , Time: 01:29:48

Communication. Features. Device variant. Copyright 2017, Builder: , Time: 01:29:48 Version V2.2.9 Release date 217-9-6 Copyright 217, Builder: 2.5.3.9, Time: 1:29:48 SM Vendor ID Device ID Vendor name Vendor text Vendor URL 31 / x136 - s: 1 54 / x1 x36 59 / x1fd - s: 1 253 / x x1 xfd