Metasys Integrator Northern Application

Transcription

1 Metasys Connectivity Technical Manual Metasys Integrator Section Application Note Issue Date 0900 APPLICATION NOTE Metasys Integrator Northern Application lntroduction Page *3 Application Details *3 Component Requirements *5 Vendor Contact Information *6 Design Considerations *6 Cable Connections 7 Cable Pinouts *7 Connecting the Cable 7 Metasys Integrator Setup *9 Point Mapping Tables 11 N750 System Status 11 Northern N750 Zone Status 12 N750 Partition Area Status 13 Metasys Network Setup *15 Mapping to a CS Object *15 Custom Integration *17 * Indicates those sections where changes have occurred since the last printing Johnson Controls, Inc. 1 Code No. LIT

2 2 Metasys Integrator Metasys Integrator Northern Application

3 lntroduction This document explains the Metasys Integrator Northern application. Use this document with the Metasys Integrator technical bulletins in the Metasys Connectivity Technical Manual (FAN 629.5), which provide information on installing and commissioning the Metasys Integrator unit. For information on vendor equipment, see Northern documentation (obtainable from a Northern representative). Note: If you are using a Universal Packaging Module (UPM) enclosure, you must install the Metasys Integrator 300 Series in a two high enclosure (EN-EWC25-0) rather than a one high enclosure (EN-EWC13-0) as shown in the figures in this application note. Application Details The Metasys Integrator unit allows Northern Computers Inc. Model N750 Security and Access Control (manufactured for Northern by Silent Knight) to communicate with the Metasys and Metasys Companion Networks. This interface provides up to 400 supervised inputs to the Metasys system with dial up communication to a Underwriters Laboratories, Inc. (UL) Listed Central Monitoring Station if desired. Each supervised input may be assigned to one of nine partitions and one of eight areas in a partition allowing the Metasys Integrator unit to schedule arm/disarm events for these points. Once a Northern N750 is connected to a Metasys or Companion Network via the Metasys Integrator unit, its data is available to the full complement of Metasys Building Automation System (BAS) features, including Change-of-State (COS) monitoring, secondary reporting and alarm notification, trend, and totalization. Metasys Integrator Metasys Integrator Northern Application 3

4 N1 LAN Metasys Integrator RS ft Maximum Northern Panel UNT N2 Bus North1 Note: If you are using a UPM enclosure, you must install the Metasys Integrator 300 Series in a two high enclosure (EN-EWC25-0) rather than a one high enclosure (EN-EWC13-0) as shown in the figures in this application note. Figure 1: Northern 750 and Metasys Integration Panel Unit Workstation Metasys Integrator RS ft Maximum Northern Panel N2 Bus Note: A PC version and converter may be substituted for the Panel unit. Northcomp Note: If you are using a UPM enclosure, you must install the Metasys Integrator 300 Series in a two high enclosure (EN-EWC25-0) rather than a one high enclosure (EN-EWC13-0) as shown in the figures in this application note. Figure 2: Northern 750 and Metasys Companion Integration 4 Metasys Integrator Metasys Integrator Northern Application

5 Component Requirements Metasys Release Requirements Metasys Companion Release Requirements Vendor Component Requirements To integrate the Northern 750 panel, you need the following: properly installed Northern 750 RS-232 null modem cable (Northern Part No. N-750-CBL-PI) Metasys Integrator unit N2 Bus (for connecting the Metasys Integrator unit to the Metasys Network Control Module [NCM] or Companion Network) portable Personal Computer (PC) for downloading vendor communication tables (.VCT files) and network setup information, and for running diagnostics cable for connecting a portable PC to the Metasys Integrator unit serial/parallel interface for direct connection to N750 (Northern Part Number N-750-PI). We recommend two N750-PI ports: one for connection to the Metasys Integrator unit and one for local programming. the correct vendor communication table (.VCT file) to download into the Metasys Integrator unit (supplied on CD-ROM) This document describes the RS-232 cable and the vendor communication tables. Northern documentation describes their equipment. The remaining components are described in the Metasys Integrator technical bulletins in the Metasys Connectivity Technical Manual (FAN 629.5). To integrate Northern equipment into the Metasys Network, you need: Metasys Operator Workstation (OWS) software Release 7.0 or higher Metasys Integrator software/firmware Release 9.0 or higher To integrate Northern equipment into the Metasys Companion Network, you need: Metasys Companion Release 5.0 or higher Metasys Integrator software/firmware Release 9.0 or higher Integration between the Metasys Integrator unit and Northern has been tested with the Northern N750 OS Version F. Changes to this equipment or integration of Northern products not discussed in this document will require additional software development and testing by Systems Products. For information on integrating other products, refer to the Custom Integration section in this application note. Metasys Integrator Metasys Integrator Northern Application 5

6 Vendor Contact Information Design Considerations Northern Computers, Inc., Technical Support 5007 S. Howell Avenue Milwaukee, WI Phone: (888) Internet: When integrating the Northern N750, consider the following: Make sure the Northern N750 equipment is set up and running properly before integrating with a Metasys or Companion system. (The Northern representative is responsible for operation of Northern equipment.) The System Status.VCT files must be defined and given as an N2 address. Along with reading the system status, this application is required to initiate communications with the gateway. Metasys Integrator Northern N750 devices will fall offline while a PC is running Northern N Download software. Although the Metasys Integrator unit can relinquish to other communication devices (such as Northern N750 Access Control Administration software), use of the software will also cause the devices to fall offline; therefore, use of any other communication software for any reason other than to download the gateway is not supported. The operating system date must be June or July, 1998 or later. To verify operating system date, view Stat, Option 4 at the Liquid Crystal Display (LCD). The Metasys Integrator unit will not come on-line with the Northern N750 if a Reporting Account number is defined in the N750 database. Table 1 shows the port setup for NC750. Table 1: NC750 Port Setup Port Setup for NC750 (No reporting accounts should be directed to the serial port device defined for connecting to Metasys Integrator unit.) Baud Rate Word Length (Data Bits) 8 Stop Bit 1 Parity PRN Off-line Time 0 Number of Rings 1 Modem Initiation Interface None Blank RS Metasys Integrator Metasys Integrator Northern Application

7 Cable Connections Cable Pinouts Use the following cable pinouts for the RS-232 connection between the Metasys Integrator unit and the Northern 750 panel: Vendor Port A or B on Integrator DB-9 Female RS-232 via N-750 Pl Com. Device DB-9 Female Signal Pin Pin RS-232 RD TD GND RTS 7 8 CTS 8 7 (50 ft maximum) P2 or P3 on Panel Figure 3: Cable Pinouts Signal TXD RXD GND CTS RTS RS 232 Connector North2 Connecting the Cable Connect the female end of the RS-232 cable to either Vendor Port A or Vendor Port B on the Metasys Integrator unit. Connect the male end to the RS-232 port on the RS-232 to RS-485 converter. Metasys Integrator Northern N750 Vendor Port A or B RS-232 RS-232 Connector North3 Figure 4: Port-to-Port Connection Metasys Integrator Metasys Integrator Northern Application 7

8 8 Metasys Integrator Metasys Integrator Northern Application

9 Metasys Integrator Setup To set up the Metasys Integrator unit, use a portable PC connected to the Metasys Integrator Terminal Port. Metasys Integrator setup involves: downloading the correct vendor communication table (.VCT file) setting up the ports setting up the network addressing Table 2 provides information specific to the Northern application. For detailed procedures, see the Metasys Integrator technical bulletins in the Metasys Connectivity Technical Manual (FAN 629.5). Metasys Integrator Metasys Integrator Northern Application 9

10 Table 2: Metasys Integrator Setup for Northern Control Panel Vendor Communication Table (.VCT File) NOR_SYS.VCT N750 System Status NOR_ZONE.VCT N750 Zone Status NOR_AREA.VCT N750 Partition Area Status Port Setup Baud Rate Word Length (Data Bits) 8 Stop Bit 1 Parity Interface Network Setup Vendor Address NOR_SYS.VCT NOR_AREA.VCT NOR_ZONE.VCT Timeout Value NOR_SYS.VCT NOR_AREA.VCT NOR_ZONE.VCT Poll Delay NOR_SYS.VCT NOR_AREA.VCT NOR_ZONE.VCT Performance Guide Approximate Scan Time (for a single MIG device) NOR_SYS.VCT NOR_AREA.VCT NOR_ZONE.VCT None RS-232 0* 0* Zone number of first zone in group: Zones = 1 Zones = 113 Zones = 225 Zones = ms 1500 ms 1500 ms 110 ms second 1 second 1 second * Although there are no actual addresses for these devices, Metasys Integrator unit requires entry of an address. 10 Metasys Integrator Metasys Integrator Northern Application

11 Point Mapping Tables Table 3 shows the points available for mapping in the Northern N750 (System Status: NOR_SYS.VCT): N750 System Status To get the hardware reference for mapping points to CS object attributes (via the software model), combine the NPT (Network Point Type) and NPA (Network Point Address). For example, the hardware reference for the AC Trouble point is 1. Table 3: N750 System Status NPT 1 NPA 2 Unit Description BO 3 BO All of the following points support the Trouble Status: AC Trouble 0-normal, 1-N/A Battery Trouble 0-normal, 1-N/A Fire Bell Trouble 0-normal, 1-N/A Smoke Power Trouble 0-normal, 1-N/A Phone Line 1 Trouble 0-normal, 1-N/A Phone Line 2 Trouble 0-normal, 1-N/A IO Device Trouble 0-normal, 1-N/A Account Trouble 0-normal, 1-N/A Printer Trouble 0-normal, 1-N/A Auxiliary Power Trouble 0-normal, 1-N/A Programming Error 0-normal, 1-N/A External Modem Trouble 0-normal, 1-N/A Service Required 0-normal, 1-N/A Silence All Partition Alarms/Troubles 0-N/A, 1-silence for partition = NPA Silence All Alarms/Troubles 0-N/A, 1-silence 1 Network Point Type 2 Network Point Address 3 Do not map these points to Companion BO points. If you map these points to Metasys BO objects, make sure the Auto Restore option in the BO object s Definition and Focus window is disabled. Metasys Integrator Metasys Integrator Northern Application 11

12 Northern N750 Zone Status The following table shows the points available for mapping in the Northern N750 (Zone Status: NOR_ZONE.VCT): Table 4: Northern N750 Zone Status NPT 1 NPA 2 Unit Description All of the following points support the Trouble Status: Zone Status 0-normal, 1-alarm BD Zone Not Ready 0-no, 1-yes BO Bypass Zone 0-no, 1-yes 1 Network Point Type 2 Network Point Address 3 In blocks of 112 zones per N2 address Note: All points related to a zone will be unreliable if the zone is undefined or is not used. There are up to 400 base zones, with 48 extra keypad zones available. All zones can be supported by defining up to four different N2 addresses using the start offset for the group of zones. To calculate the zone number: Zone Number = Vendor Address + NPA - 1 Example 1: Vendor Address = 1, Point Number (NPA) = 50 Zone Number is 50 Example 2: Vendor Address = 225, Point Number (NPA) = 76 Zone Number = Metasys Integrator Metasys Integrator Northern Application

13 N750 Partition Area Status Table 5 shows the points available for mapping in the Northern N750 (Partition Area Status: NOR_AREA.VCT): Table 5: Northern N750 Partition Area Status NPT 1 NPA 2 Unit Description BD BD BD BD BD BD BD BD BO BO BO BO BO BO BO BO Trouble Status (1 to 64 support the Trouble Status.) Partition 1 Area 1-8 Status 0-normal, 1-alarm Partition 2 Area 1-8 Status 0-normal, 1-alarm Partition 3 Area 1-8 Status 0-normal, 1-alarm Partition 4 Area 1-8 Status 0-normal, 1-alarm Partition 5 Area 1-8 Status 0-normal, 1-alarm Partition 6 Area 1-8 Status 0-normal, 1-alarm Partition 7 Area 1-8 Status 0-normal, 1-alarm Partition 8 Area 1-8 Status 0-normal, 1-alarm Partition 1 Area 1-8 Armed 0-disarm, 1-armed Partition 2 Area 1-8 Armed 0-disarm, 1-armed Partition 3 Area 1-8 Armed 0-disarm, 1-armed Partition 4 Area 1-8 Armed 0-disarm, 1-armed Partition 5 Area 1-8 Armed 0-disarm, 1-armed Partition 6 Area 1-8 Armed 0-disarm, 1-armed Partition 7 Area 1-8 Armed 0-disarm, 1-armed Partition 8 Area 1-8 Armed 0-disarm, 1-armed Partition 1 Area 1-8 Not Ready 0-no, 1-yes Partition 2 Area 1-8 Not Ready 0-no, 1-yes Partition 3 Area 1-8 Not Ready 0-no, 1-yes Partition 4 Area 1-8 Not Ready 0-no, 1-yes Partition 5 Area 1-8 Not Ready 0-no, 1-yes Partition 6 Area 1-8 Not Ready 0-no, 1-yes Partition 7 Area 1-8 Not Ready 0-no, 1-yes Partition 8 Area 1-8 Not Ready 0-no, 1-yes Arm Partition 1 Area* 0-disarm, 1-arm Arm Partition 2 Area* 0-disarm, 1-arm Arm Partition 3 Area* 0-disarm, 1-arm Arm Partition 4 Area* 0-disarm, 1-arm Arm Partition 5 Area* 0-disarm, 1-arm Arm Partition 6 Area* 0-disarm, 1-arm Arm Partition 7 Area* 0-disarm, 1-arm Arm Partition 8 Area* 0-disarm, 1-arm 1 Network Point Type 2 Network Point Address * Disarming a partition also resets the alarm status of the N750. Metasys Integrator Metasys Integrator Northern Application 13

14 14 Metasys Integrator Metasys Integrator Northern Application

15 Metasys Network Setup Metasys Network setup is described in the Metasys Integrator technical bulletins in the Metasys Connectivity Technical Manual (FAN 629.5). This section contains details specific to Northern applications. It is recommended that all points that report an alarm or trouble status be directly mapped to objects. Mapping to a CS Object Table 6: Software Model and CS Object Definition Application Software Model (on Tables and Models CD-ROM) Display Attribute (recommended) System Status NOR_SYS.DDL 1 BO1 Zone Status NOR_ZONE.DDL 1 BO1 Area Status NOR_AREA.DDL 1 BO1 NT Command Attribute (recommended) Metasys Integrator Metasys Integrator Northern Application 15

16 16 Metasys Integrator Metasys Integrator Northern Application

17 Custom Integration For information on integrating products that are not discussed in this document, first refer to the Metasys Compatible Global Catalog, an online list of released Connectivity products. If this list does not provide the information you require, consider using the System Integration Project Data Sheet to request a custom contract from the System Integration Team. Both the Metasys Compatible Global Catalog and the System Integration Project Data Sheet can be accessed from The Advisor by performing the following steps: 1. Click on the Systems Products button located on the left side of The Advisor home page. 2. Click on the Product Literature link. 3. Click on the Manuals-FANS link. 4. Click on the Metasys Connectivity Sales Resource Manual link. 5. Find the System Integration Project Data Sheet link in the Table of Contents. Click on this link to view an online copy of the System Integration Project Data Sheet, or click on the Metasys Compatible Global Catalog link below it to view a list of released Connectivity products. The System Integration Project Data Sheet (LIT ) can also be found in the Metasys Connectivity Sales Resource Manual (FAN 629). If you need further assistance, contact the Johnson Controls Field Support Center. Metasys Integrator Metasys Integrator Northern Application 17

18 Notes 18 Metasys Integrator Metasys Integrator Northern Application

19 Notes Metasys Integrator Metasys Integrator Northern Application 19

20 Notes Controls Group FAN E. Michigan Street Metasys Connectivity Technical Manual P.O. Box 423 Metasys Integrator Release 9.0 Milwaukee, WI Printed in U.S.A. 20 Metasys Integrator Metasys Integrator Northern Application