TC-net OPC Server Instruction Manual 6F8C1368

Transcription

1 TC-net OPC Server Instruction Manual 6F8C1368

2 13th Edition 21 th August The material in this manual may be revised without notice. Copy right by Toshiba Corporation. All rights reserved. No part of this manual may be reproduced in any form without permission.

3 Introduction Safety Precautions The instruction manual and the labels affixed to the products or equipment give important information for using products safely. It helps prevent damage to properties and hazard to people who use them or work with them. Make yourself familiar with the signal words and signs in this page, then read the safety precautions that follow and always follow the instructions to avoid hazards. Explanation of signal words Signal word is a word that designates a degree or level of hazard seriousness. The words WARNING and CAUTION are used for the products. WARNING CAUTION Indicates a potentially hazardous situation which could result in death or serious injury, if you do not follow the instructions. Indicates a potentially hazardous situation which may result in minor or moderate injury and/or property damage, if you do not follow the instructions. Hazard alert shapes and symbols Following shapes and symbols are used in the safety precaution labels affixed to the products and in other places including operation manuals for giving safety instructions. Filled circle means "Mandatory Action" or "Do as indicated." Required action is shown in the circle or described near the circle. Circle band with a diagonal slash means "Prohibition" or " You must not do." Prohibited action is shown in the circle or described near the circle. Triangle means "Hazard Alerting" or "Be alert against hazard." The kind of hazard is shown in the triangle or described near the triangle. Exclamation point with a triangle is a safety alert symbol which indicates a potential hazard. It is used with a Signal Word. Square or rectangle means "Information Messages" or "Notice." Important precautions for system operation System fault or data loss may occur in the event of power outage whether it is external or internal of the system. Take precautions in advance to protect the system in order to prevent such event to take place. Also back up your data regularly to minimize the possible damage by loss of data as a result of such event. Confirmation of product safety label Confirm that product safety labels are put on the front panel of the power supply module. If the label is lost or soiled, inform TOSHIBA Corporation. i

4 Introduction Introduction This manual explains how to use OPC Server for TC-net 100 and TC-net 1G *1. First, read "Safety Precautions" carefully to use this device safely and correctly. After you read this manual, keep it in a place where you can find it easily when you need it. Composition of This Manual This manual is composed of the following chapters. Chapter 1 Outline of OPC Server This explains the functions and composition of the OPC Server and needful processes for managing OPC Server. Chapter 2 Setting-Up OPC Server This explains how to install, reinstall, uninstall and update the OPC Server. Chapter 3 How to set the environments for connecting with OPC This explains how to set the environments (DCOM, Security and Firewall etc.) which OPC clients connect to OPC Server with. Chapter 4 Launch / Close OPC Server This explains how to launch OPC Server. Chapter 5 Dual function This explains the dual constitution of the OPC server. Chapter 6 List of OPC items This explains the item of a state and the dual state of OPC server oneself. Chapter 7 How to set the environment for OPC Server This explains about how to set the environment for OPC server action. Chapter 8 Log Save Tool This explains a function to store an OPC server-related log file for a long time. Chapter 9 Log Decompress Tool This explains a function to decompress a stored log file for a long time. Chapter 10 RAS function *1 This explains the RAS function of the OPC server. *1 : Support of TC-net1G and RAS function added in V01.60 Microsoft and Windows are trademarks of US Microsoft Corporation registered in U.S.A. and other countries. Other company names and product names described in this manual are the trademarks and registered trademarks of the respective companies. ii

5 Introduction Reference Manual The reference manual is as follows: TC-net OPC Server Setting Tool Instruction Manual 6F8C1369 Conventions used in this manual Other than safety precaution items, the following symbols are used to explain items that need your attention. Important: Explains items required to use the product correctly. Tip: Introduces referential matters to help you understand the main text. Reference: Documents you should refer to help you understand the main text. Indicates reference locations of this manual or other manuals. Prohibition of copying This OPC server is protected by Copyright. This OPC server can be installed in only one computer. When it is necessary to install OPC server in another computer by dual constitution, please buy the OPC server software newly. iii

6 Contents Contents Safety Precautions Introduction i iii 1. Outline of OPC Server Outline of OPC Server Environments Constitution Specifications Data type ProgID 6 2. Setting-Up OPC Server Installation Maintenance Uninstallation How to set the environments for connecting with OPC DCOM Setting Security Setting Windows Firewall User Account Control (Windows 8.1, Windows 7, Windows Vista, Windows Server 2012 R2, Windows Server 2008 R2 and Windows Server 2008 only) Launch / Close OPC Server Launch OPC Server Close OPC Server About TC-net Type About Version of OPC Server Client Connection Status Dual Function Construction and outline Dual state management List of OPC Items The List of OPC items How to set the environment for OPC Server How to set the environment for OPC Server Log Output of Scan Memory Access Performance Time adjusting function with TC-net Log Save Tool Outline of Log Save Tool Launch / Close Log Save Tool 98 iv

7 Contents Launch Log Save Tool Close Log Save Tool Screen / Operation instructions Screen instructions Operation instructions Decompress log files How to Decompress log files Log Decompress Tool Outline of Log Decompress Tool Setting-Up Log Decompress Tool Installing Microsoft.Net Framework 2.0/ Installing Log Decompress Tool Uninstalling Log Decompress Tool Launch Log Decompress Tool Screen / Operation instructions RAS function RAS function 121 v

8

9 1. Outline of OPC Server 1. Outline of OPC Server TC-net OPC Server is the local / remote server for OPC Data Access 2.05a /3.0 on Windows system. It provides the environments in order to access scan memories of TC-net from OPC clients. This chapter describes the outline, the movement environment and the construction of OPC Server Outline of OPC Server OPC is open connectivity in industrial automation and the enterprise systems that support industry. By using OPC, the application can access it without being conscious of the style of process data. In addition, OPC succeeds to the client / server model based on OLE/COM technology of Microsoft. It is not necessary for the OPC client to understand the access methods about the physics device by this. A client can have access to an OPC server of the different vender by means same by using standardized specifications (interface). This OPC Server supports the following OPC interfaces. DA2.05a (Data Access 2.05a) DA3.0 (Data Access 3.0) About details of OPC, refer to the following Web site. Table 1.1 OPC URL Web Site URL OPC Foundation OPC Japan OPC Europe *)Above URL is as of March

10 1. Outline of OPC Server 1.2. Environments TC-net OPC Server needs the following environments. Item Processor Table 1.2 Environments Condition Pentium 4 Processor 3.0GHz or more memory 1.0GB or more Operating System Windows 8.1 Pro [x64] *1 HDD Space Capacity Needful package software Windows 7 Professional [x86/x64] SP1 or later Windows Vista Ultimate / Enterprise SP1 or later Windows Server 2012 R2 Standard [x64] Windows Server 2008 R2 Standard [x64] SP1 Windows Server 2008 Standard [x86] SP2 Windows Server 2003 R2 SP2 or later *1 : 64 bits version OS support is added in TC-net OPC Server V01.80, but execute TC-net OPC Server with 32 bits mode. 10MB or more TC-net100 PCI Bus Card Support Software (SEJTNI2A) V01.30 or later Important: V01.40 is necessary if the OS is Windows Server 2008 [x86] SP2. TC-net100 PCI Express Bus Card Support Software (SEJTNEWA) V01.01 or later --- for the 32 bits version OS *This support was added in TC-net OPC Server V TC-net100 PCI Express Bus Card Support Software (SHJTNR2A) V01.20 or later --- for the 64 bits version OS TC-net1G PCI Bus Card Support Software (SHJTGW8A) V01.05 or later --- for the 32 bits version OS *Support of TC-net1G added in TC-net OPC Server V TC-net1G PCI Bus Card Support Software (SHJTGR2A) V01.10 or later --- for the 64 bits version OS Important: There is a description of "TC-net OPC Server destination folder" in this manual, but becomes the following folder when it is used the 64 bits version OS. Destination folder in case of the 64 bits version OS: C:\Program Files (x86)\toshiba\tc_net OPC Server Important: There is a description of System Folder (C:\Windows\System32) in this manual, but becomes the following folder when it is used the 64 bits version OS. System Folder in case of the 64 bits version OS: C:\Windows\SysWOW64 2

11 1. Outline of OPC Server 1.3. Constitution The constitution of OPC Server is described below. OPC Client OPC Server Setting Tool Ethernet OPC Server OPC Server Function OPC Client OPC Server TC-net Access Function Tool I/F Function OPC Setting Files TC-net PCI Bus Card Support Software Dual Management TC-net PCI Bus Card (JTNI/JTGI) Log Save Tool TC-net100 or TC-net1G TC-net nvcon nvcon nvcon nvcon TC-net nvcon nvcon nvcon nvcon This is included in TC-net OPC server package software. Figure 1.1 Example of System Configuration Table 1.3 Description of functions OPC Client OPC Server Setting Tool OPC Server Function Tool I/F Function OPC Setting files Dual Management TC-net Access Function Log Save Tool (*1) TC-net PCI Bus Card Support Software This is OPC Client Application. It can have access to OPC Server from local side or remote side. This is an engineering tool to configure system of OPC Server. This is the original functions of OPC Server. This is the function which communicates between OPC Server Setting tool and OPC Server. These are the information files downloaded from OPC Server Setting Tool. This is the function which manages dual OPC Servers. This is the function which manages TC-net and reads and writes scan data. This is the function to store an OPC server-related log file for a long time. This is Driver and API for TC-net 100/1G PCI Bus Card (JTNI/JTGI) *1 : Log Save Tool added in V

12 1. Outline of OPC Server 1.4. Specifications The specifications of functions for data access of TC-net scan memory are described below. Figure 1.4 Specifications of data access Access Method Description Read Synchronous read Reads the scan memory data corresponding to an item. Waits until reading is completed. Asynchronous read Reads the scan memory data corresponding to an item. Returns to the original state immediately after a request, and calls the method on the OPC client side when reading is completed. Data change notification (Subscription) Checks periodically and reports to the OPC client of changes of scan memory data of a Certain width or greater. Write Synchronous write Writes to the scan memory data. Waits until writing is completed. Asynchronous write Writes to the scan memory data. Returns to the original state immediately after a request, and calls the method on the OPC client side when writing is completed. Important: No special security is set for writing to the scan memory of TC-net. Therefor you must write from OPC Server in consideration of influence on system. 4

13 1. Outline of OPC Server The standard of the OPC DA interface and the supported range with the TC-net OPC server are described in the following table. ( :Support, :Not Support) Table 1.5 The standard of the OPC DA interface and the supported range with the TC-net OPC server Object Interface Support Remark OPCServer IOPCServer IOPCServerPublicGroups IOPCBrowseServerAddressSpace BrowseAccessPaths is not supported. IPersistFile IOPCItemProperties IOPCCommon IOPCItemIO Only DA 3.0 IOPCBrowse Only DA 3.0 IConnectionPointContainer OPCGroup IOPCGroupStateMgt IOPCGroupStateMgt2 Only DA 3.0 IOPCPublicGroupStateMgt IOPCSyncIO IOPCSyncIO2 Only DA 3.0 IOPCAsyncIO IOPCAsyncIO2 IOPCAsyncIO3 Only DA 3.0 IOPCItemMgt IOPCItemDeadbandMgt Only DA 3.0 IOPCItemSamplingMgt Only DA 3.0 IDataObject IConnectionPointContainer IConnectionPoint IEnumConnectionPoints IEnumConnections IEnumOPCItemAttributes IEnumString IEnumUnknown Client IAdviseSink IOPCDataCallback IOPCShutdown 5

14 1. Outline of OPC Server 1.5. Data type The supported types of data are described below. Table 1.6 Data Type Supported Data Type Data Type Bit VT_BOOL 16 Bits Integer (unsigned) VT_UI2 Data Type in OPC Server 16 Bits Integer (singed) VT_I2 32 Bits Integer (unsigned) VT_UI4 32 Bits Integer (singed) VT_I4 32Bit Real VT_R4 String VT_BSTR Bit Array VT_BOOL VT_ARRAY 16 Bits Integer Array (unsigned) VT_UI2 VT_ARRAY 16 Bits Integer Array (singed) VT_I2 VT_ARRAY 32 Bits Integer Array (unsigned) VT_UI4 VT_ARRAY 32 Bits Integer Array (singed) VT_I4 VT_ARRAY 32 Bit Real Array VT_R4 VT_ARRAY Reference: *1) String Array Type isn t supported. *2) The character numbers of string data is from 1 by *3) The number of array is from 2 by Data Type VT_BOOL 0,1 VT_UI2 0 ~ VT_I ~ VT_UI4 0 ~ Table 1.7 Range of Value VT_I ~ VT_R4 VT_BSTR Range E38 ~ E38 (include 0 and integer) ASCII Code 1.6. ProgID Program ID (ProgID) of TC-net OPC server are described below. ProgID Toshiba_TC_net_DA.1 6

15 2. Setting-Up OPC Server 2. Setting-Up OPC Server This chapter describes installation, maintenance and uninstall of OPC Server. Important: TC-net OPC Server needs TC-net PCI Bus Support Software. Before installing TC-net OPC Server, pelease install TC-net PCI Bus Support Software. Important: "Microsoft.Net Framework version 2.0" are necessary for execution environment of a Log Save Tool. Install it according to "9.2.1 Installing Microsoft.Net Framework 2.0" Installation There are the following three types of installation. (1) Both Install OPC Server and environments to develop OPC Client. (2) Client Install environments to develop OPC Client only. (3) Server Install OPC Server only. These types are selected at the time of installing. When you install to PC for OPC Server, you must select Both or Server. When you install to PC for only OPC Client, you must select Client. Install OPC Server from CD. Proceed as shown below. <1>Launch Setup.exe under in CD. Input Serial numbers and click <Run>. 7

16 2. Setting-Up OPC Server <2>Select TC-net OPC Server SATOPCSA VXX.XX and click <Install>. (VXX.XX is the version.) <3> Click <Next>. <4> Licensing Agreement is displayed. If you agree, click <Yes>. <5>Select Install folder. Normally it is C:\Program Files\Toshiba\TC_net OPC Server. If you change it, click <Browse > After setting, click <Next>. In case of the 64 bits version OS, select Install folder "C:\Program Files (x86)\toshiba\tc_net OPC Server". 8

17 2. Setting-Up OPC Server <6>Select type of installation. Click < Next >. <7>Select TC-net100(JTNI) or TC-net1G(JTGI) Card Type. Click < Next >. When installation type that selected "Both" or "Server" in <6>, this dialog is displayed. * : This dialog added in V01.60 <8>Program group name is specified. Default is [TC-net OPC Server]. Don t change this. Click < Next >. <9>An inquiry doing DCOM setting is displayed. When set it automatically, Click < Yes >. When set a manual operation later, Click < No >. A displayed message changes by the installation type that selected in <6>. About contents of setting, please refer to "3.1. DCOM Setting ". * : DCOM setting function added in V

18 2. Setting-Up OPC Server <10> DCOM setting is completed. Click < OK >. <11>When installation type that selected "Both" or "Server" in <6>, an inquiry starting Log Save Tool processing automatically is displayed. * : Log Save Tool function added in V <12>Installation is completed. Click <Finish> Maintenance Figure 2.1 Install OPC Server There are the modification (the change of the installation type) and the revision (a reinstallation and version up) for maintenance. Important: Disconnect from the clients before modifying or repairing Modify The way to change installation type is described below. <1>Launch Setup.exe under in CD. Input Serial numbers and click <Run>. 10

19 2. Setting-Up OPC Server <2>Select TC-net OPC Server SATOPCSA VXX.XX and click <Install>. (VXX.XX is the version.) <3> Select <Modify> and click <Next>. <4>Change installation type. Click <Next>. <5>An inquiry doing DCOM setting is displayed. When set it automatically, Click < Yes >. When set a manual operation later, Click < No >. A displayed message changes by the installation type that selected in <6>. About contents of setting, please refer to "3.1. DCOM Setting ". * : DCOM setting function added in V <6> DCOM setting is completed. Click < OK >. 11

20 2. Setting-Up OPC Server <7>When installation type that selected "Both" or "Server" in <6>, an inquiry starting Log Save Tool processing automatically is displayed. * : Log Save Tool function added in V <8>Change is completed. Click <Finish>. Figure 2.2 Modify installation type of OPC Server Repair The way to reinstall or version-up is described below. Important: When TC-net OPC Server and Log Save Tool is running, you must stop it. Refer to 4.2 Close OPC Server. <1>Launch Setup.exe under in CD. Input Serial numbers and click <Run>. <2>Select TC-net OPC Server SATOPCSA VXX.XX and click <Install>. (VXX.XX is the version.) 12

21 2. Setting-Up OPC Server <3> Select <Repair> and click <Next>. <4>An inquiry doing DCOM setting is displayed. When set it automatically, Click < Yes >. When set a manual operation later, Click < No >. A displayed message changes by the installation type that selected in <6>. About contents of setting, please refer to "3.1. DCOM Setting ". * : DCOM setting function added in V <5> DCOM setting is completed. Click < OK >. <6>When installation type that selected "Both" or "Server" in <6>, an inquiry starting Log Save Tool processing automatically is displayed. * : Log Save Tool function added in V <7>Reinstallation is completed. Click <Finish>. Figure 2.3 Repair of OPC Server 13

22 2. Setting-Up OPC Server 2.3. Uninstallation Important: When TC-net OPC Server and Log Save Tool is running, you must stop it. Refer to 4.2 Close OPC Server. Important: When a file of extension of BAK and ORG can be left, after uninstallation, you open Explorer, and delete it by manual operation. Important: Disconnect from the clients before uninstalling On Windows 8.1 / Windows 7 / Windows Vista / Windows Server 2012 R2/ Windows Server 2008 R2 / Windows Server 2008 Uninstall the OPC Server with [Control Panel] [Programs and Features] <1> On Windows 8.1/Windows Server 2012 R2 Open the menu by right-clicking the left side on the task bar, open the Control Panel. Others Open Control Panel from start menu. 14

23 2. Setting-Up OPC Server <2> Open Control Panel. Select [Uninstall a program]. When the view is "Classic View" or "Large icons" or "Small icons", select < Programs and Features >. <3>Select TC-net OPC Server and Click <Uninstall/Change> button. It starts to remove program. <4> Select Remove and click <Next>. <5> The message that make sure to remove is displayed and click <OK>. It starts to remove program. 15

24 2. Setting-Up OPC Server <6> Uninstallation is completed. Click <Close>. Figure 2.4 Uninstall OPC Server on Windows 8.1 / Windows 7 / Windows Vista / Windows Server 2012 R2 / Windows Server 2008 R2 / Windows Server On Windows Server 2003 Uninstall the OPC Server with [Control Panel] [Add or Remove Programs] <1> Select <Add or Remove Programs>. <2>Select TC-net OPC Server and Click <Change/Remove> button. It starts to remove program. 16

25 2. Setting-Up OPC Server <3> Select Remove and click <Next>. <4> The message that make sure to remove is displayed and click <OK>. It starts to remove program. <5> Uninstallation is completed. Click <Finish>. Figure 2.5 Uninstall OPC Server on Windows Server

26 2. Setting-Up OPC Server 18

27 3. How to set the environments for connecting OPC 3. How to set the environments for connecting with OPC The OPC server and OPC clients access data via a network to communicate each other. To realize this, some environment settings are required. This section describes how to set the environment settings. When OPC Server and OPC Clients runs on one PC, these setting are unnecessary. Important: If you would not like to lower security level, logon with the same user name and the same password in OPC Server and OPC Client. We recommend you that user name of OPC Server and one of OPC Client is same. Tip: If OPC Clients can t connect to OPC Server, you may delete Internet Protocol Version 6 (TCP/IPv6) in Network Protocols on Network Connections. 19

28 3. How to set the environments for connecting OPC 3.1. DCOM Setting When did DCOM setting at the time of installation, this setting is unnecessary. The dcomcnfg command is a command to make the security setting to execute OPC communications through the computer network On Windows 8.1/ Windows 7 / Windows Vista / Windows Server 2012 R2/ Windows Server 2008 R2/ Windows Server 2008 / DCOMCNFG Setting On Windows 8.1/On Windows Server 2012 R2 <1> Open the menu by right-clicking the left side on the task bar, Click [Run] on the menu Enter dcomcnfg in the Run dialog and click <OK>. Others Figure3.1 DCOMCNFG Setting (Windows 8.1/Windows Server 2012 R2) <1> Click [Start] on start menu Enter dcomcnfg in Start Search box and push <ENTER> key. Figure 3.2 DCOMCNFG Setting (Windows 7/Windows Vista/Windows Server 2008 R2/Windows Server 2008) 20

29 3. How to set the environments for connecting OPC Changing default properties This setting must be done in both PCs for OPC Server and OPC Clients. <1> Execute the commands in the following order: Console Root Component Services Computers My Computer. Right-click the My Computer and select Property menu. <2> Select the Default Properties tab in the My Computer Properties window and make the following settings. Table 3.1 Default properties Item Enable Distributed COM on this computer Enable COM Internet service on this computer Default Authentication Level Default Impersonation Level Selection Check this item Not check this item Connect Identify When there is difference between authentication level of OPC client-side and one of OPC server side, It is accorded with high one. In addition, the authentication level is a turn of "the None < connection < summons < packet". 21

30 3. How to set the environments for connecting OPC <3> Click COM Security tab and click < Edit Limits > in Access Permissions. <4> Select "ANONYMOUS LOGON" user and check permission of "Remote Access" and set it so that "Local Access" and "Remote Access" become a check state. Click <OK>. 22

31 3. How to set the environments for connecting OPC <5> Click Edit Limits in Launch and Activation Permissions. <6> Check Remote Launch and Remote Activation for Everyone user, and set it so that all four items become a check state like the right screen. Click <OK>. 23

32 3. How to set the environments for connecting OPC <7> Click <OK> on My Computer Properties dialog. Figure 3.3 Changing default properties (Windows 8.1/ Windows 7/Windows Vista/ Windows Server 2008/Windows Server 2008 R2/Windows Server 2012 R2) OPC Server Setting This Setting is on PC for OPC Server. <1> Execute the commands in the following order: Console Root Component Services Computers My Computer. Select DCOM Config and select TOSHIBA TC-net OPC Data Access Server in the application list. Right-click the TOSHIBA TC-net OPC Data Access Server and select Property menu. 24

33 3. How to set the environments for connecting OPC <2> Select the General tab in the TOSHIBA TC-net OPC Data Access Server Properties window and make authentication level Connect. <3> Select the Security tab in the TOSHIBA TC-net OPC Data Access Server Properties window and select Customize in Launch and Activation Permissions and click <Edit >. <4> Click <Add > on Launch and Activation Permission window. 25

34 3. How to set the environments for connecting OPC <5> Click <Advanced > on Select Users or Groups window. Add Everyone. <6> Select Everyone on [Group or user names] and check Remote Launch, Local Activation and Remote Activation, and set it so that all four items become a check state. Click <OK>. 26

35 3. How to set the environments for connecting OPC <7> Select the Security tab in the TOSHIBA TC-net OPC Data Access Server Properties window and select Customize in Access Permissions and click <Edit >. <8> Click <Add > on Access Permission window. Add Everyone to [Group or user names] like <5> and, Select Everyone on Access Permission window to permit Remote Access. Set it so that "Local Access" and "Remote Access" become a check state. Click <OK>. <9> Select the Identify tab in the TOSHIBA TC-net OPC Data Access Server Properties window and select The interactive user and click <OK>. Close Component Services Figure 3.4 OPC Server Setting (Windows8.1/ Windows7/Windows Vista/ Windows Server 2008/Windows Server 2008 R2/Windows Server 2012 R2) 27

36 3. How to set the environments for connecting OPC Important: On Identify, you must select The interactive user. If you select other user, OPC Server doesn t run normally. 28

37 3. How to set the environments for connecting OPC Windows XP / On Windows Server 2003 DCOMCNFG Setting <1> Click [Run] on start menu Enter dcomcnfg in Run dialog and click <OK>. So the right dialog is displayed. Click <OK>. Figure 3.5 DCOMCNFG Setting (Windows XP/Windows Server 2003) Changing default properties This setting must be done in both PCs for OPC Server and OPC Clients. <1> Execute the commands in the following order: Console Root Component Services Computers My Computer. Right-click the My Computer and select Property menu. 29

38 3. How to set the environments for connecting OPC <2> Select the Default Properties tab in the My Computer Properties window and make the following settings. Table 3.2 Default properties Item Enable Distributed COM on this computer Enable COM Internet service on this computer Default Authentication Level Default Impersonation Level Selection Check this item Not check this item Connect Identify When there is difference between authentication level of OPC client-side and one of OPC server side, It is accorded with high one. In addition, the authentication level is a turn of "the None < connection < summons < packet". <3> Click COM Security tab and click < Edit Limits > in Access Permissions. 30

39 3. How to set the environments for connecting OPC <4> Select ANONYMOUS LOGON user to allow Remote Access. Set it so that "Local Access" and "Remote Access" become a check state. Click <OK>. <5>Click Edit Limits in Launch and Activation Permissions. 31

40 3. How to set the environments for connecting OPC <6> Check Remote Launch and Remote Activation for Everyone User. Set it so that all four items become a check state. <7>Click <OK> on My Computer Properties dialog. Figure 3.6 Changing default properties (Windows XP/Windows Server 2003) 32

41 3. How to set the environments for connecting OPC OPC Server Setting This Setting is on PC for OPC Server. <1> Execute the commands in the following order: Console Root Component Services Computers My Computer. Select DCOM Config and select TOSHIBA TC-net OPC Data Access Server in the application list. Right-click the TOSHIBA TC-net OPC Data Access Server and select Property menu. <2> Select the General tab in the TOSHIBA TC-net OPC Data Access Server Properties window and make authentication level Connect. <3> Select the Security tab in the TOSHIBA TC-net OPC Data Access Server Properties window and select Customize in Launch and Activation Permissions and click <Edit >. 33

42 3. How to set the environments for connecting OPC <4> Click <Add > on Launch Permission window. <5> Click <Advanced > on Select Users or Groups window. Add Everyone. 34

43 3. How to set the environments for connecting OPC <6> Like the right figure, Select Everyone [Group or user names] and check Remote Launch, Local Activation and Remote Activation. Set it so that all four items become a check state. Click <OK>. When a list of [Group or user names] does not have Administrators, you add it same as above <4> - <5>. <7> Select the Security tab in the TOSHIBA TC-net OPC Data Access Server Properties window and select Customize in Access Permissions and click <Edit >. 35

44 3. How to set the environments for connecting OPC <8> Click <Add > on Access Permission window. Add Everyone to [Group or user names]. Like the right figure, Select Everyone on Access Permission tab to permit Remote Access. Set it so that "Local Access" and "Remote Access" become a check state. Click <OK>. When a list of [Group or user names] does not have Administrators, you add it same as above <4> - <5>. <9> Select the Identify tab in the TOSHIBA TC-net OPC Data Access Server Properties window and select The interactive user and click <OK>. Close Component Services Important: Figure 3.7 OPC Server Setting (Windows XP/Windows Server 2003) On Identify, you must select The interactive user. If you select other user, OPC Server doesn t run normally Security Setting Logon to Windows XP Professional or later from other computers is done as a Guest user. In addition, logon to Windows XP Professional from users without a password is not allowed. Therefore, to make a remote connection to OPC server, the above security setting must be changed. How to change the setting is as follows. To change the setting, it is necessary to log on as a user with Administrator privilege. This Setting is on both of OPC Server and OPC Client 36

45 3. How to set the environments for connecting OPC Local Security Policy On Windows XP/ On Windows Server 2003 <1> Open Control Panel from start menu. Select Classic View and open Administrative Tools. <2> Open Local Security Policy from Administrative Tools. 37

46 3. How to set the environments for connecting OPC <3> Select the commands in the following order: Security Settings Local Policies Security Options and select Accounts: Limit local account use of blank passwords to console logon only. <4> Select Disabled and then click [OK]. <5> Likewise, select Network access: Sharing and security model for local accounts. <6> Select Classic local users authenticate as themselves and then click [OK] Figure 3.8 Local Security Policy Setting (Windows XP/Windows Server 2003) 38

47 3. How to set the environments for connecting OPC On Windows 8.1 / Windows 7 / Windows Vista / Windows Server 2012 R2 / Windows Server 2008 R2 / Windows Server 2008 <1> On Windows 8.1/On Windows Server 2012 R2 Open the menu by right-clicking the left side on the task bar, open the Control Panel. Others Open Control Panel from start menu. <2>Select "Classic View" or "Large icons" or "Small icons" and open Administrative Tools. or 39

48 3. How to set the environments for connecting OPC <2> Open Local Security Policy from Administrative Tools. <3> Select the commands in the following order: Security Settings Local Policies Security Options and select Accounts: Limit local account use of blank passwords to console logon only. <4> Select Disabled and then click [OK]. 40

49 3. How to set the environments for connecting OPC <5> Likewise, select Network access: Sharing and security model for local accounts. <6> Select Classic local users authenticate as themselves and then click [OK] Figure 3.9 Local Security Policy Setting (Windows 8.1 / Windows 7/Windows Vista/ Windows Server 2012 R2/Windows Server 2008 R2/ Windows Server 2008) Important: Windows XP or later has an internal security function to prevent an intruder break-in. This is done by limiting the user who accesses a computer through the network as a [Guest] level. When an intruder tries to enter a computer without privilege by guessing a password to get the privilege, either he fails or he can obtain only an access level of limited [Guest] level. However, the above setting changes the internal security of Windows XP or later and this setting change results in a conventional Windows level security. Be careful about the operating environment of a machine where OPC server is installed Windows Firewall Windows XP Service Pack2 or later provides better protection against viruses, hackers, and worms, and includes Windows Firewall, Pop-up Blocker for Internet Explorer, and the new Windows Security Center. There are two functions that have direct influence on the function of OPC which uses DCOM. One is an addition of new properties for DCOM and the other is that Windows Firewall is turned on by default. To change the setting, it is necessary to log on as a user with Administrator privilege. 41

50 3. How to set the environments for connecting OPC You must do this process described below for OPC Server and OPC Clients. Important: If you turn off Windows Firewall, you can use the function of OPC without the following setting. But in order to keep your pc safer, recommend to turn on Windows Firewall. On Windows 8.1 / Windows 7 / Windows Server 2012 R2 / Windows Server 2008 R2 <1> On Windows 8.1/ /Windows Server 2012 R2 Open the menu by right-clicking the left side on the task bar, open the Control Panel. Others Open Control Panel from start menu. <2> Open Windows Firewall in System and Security. 42

51 3. How to set the environments for connecting OPC <3> Windows Firewall is turned on by default. Click <Turn Window Firewall on or off>. <4> Customize Settings window is displayed If Turn off Windows Firewall (not recommended) is selected, select Turn on Windows Firewall. Click <OK>. <5>Click "Allow a program or feature through Windows Firewall" in "Windows Firewall". 43

52 3. How to set the environments for connecting OPC. Click "Allow another program " in the "Allowed programs and features" list. <6> "Add a Program" dialog is appeared. Click <Browse >. <7> Browse dialog is appeared. Select the following programs under TC-net OPC Server destination folder (Default folder: \Program Files\TOSHIBA\TC_net OPC Server). In case of the 64 bits version OS, destination folder is "C:\Program Files (x86)\toshiba\ TC_net OPC Server". [For Server] OpcDualMng.exe (This program is indicated as Start OPC Server in [Add a Program] window.) OpcToolIfSvr.exe TCnetOPCSvr.exe And 44

53 3. How to set the environments for connecting OPC C:\Windows\System32\OPCENUM.exe In case of the 64 bits version OS, add "C:\Windows\SysWOW64\OPCENUM.exe". [For Client] All of OPC Clients C:\Windows\System32\OPCENUM.exe Click <Open>. <8>Add the selected programs. Click <Add>. <9>Search the added program in the list. When there isn't "Microsoft Management Console" (mms.exe) in the list, you must add " C:\Windows\System32\mmc.exe". In case of the 64 bits version OS, add "C:\Windows\SysWOW64\mmc.exe". If all programs are in the list, Click <OK> <10>Go back "Windows Firewall" is shown. Click "Advanced settings". 45

54 3. How to set the environments for connecting OPC <11>"Windows Firewall with Advanced Security" is shown. Select "Inbound Rules" and mouse-right-click on it. Click "New Rule " on the popup menu. <12>"New Inbound Rule Wizard" is appeared. Select "Port" and click <Next>. <13> Set the following port in "Protocol and Port". Check TCP Port No:135 Click <Next>. 46

55 3. How to set the environments for connecting OPC <14> Select "Allow the connection" in "Action". Click <Next>. <15> Select all items in "Profile". Click <Next>. <16> Set the following name port and click OK. Name :DCOM Click <Finish>. <16> And add following port likewise. Name : ToolIf Port No: Check TCP The setting for Windows Firewall is now completed. Figure 3.10 Windows Firewall on Windows 8.1 / Windows 7 / Windows Server 2012 R2 / Windows Server 2008 R2 47

56 3. How to set the environments for connecting OPC On Windows Vista / Windows Server 2008 <1> Open Control Panel from start menu. Select Classic View and open Windows Firewall. <2> Windows Firewall is turned on by default. Click <Change settings>. <3> Windows Firewall Settings window is displayed If Off is selected, select On(recommended). 48

57 3. How to set the environments for connecting OPC <4> Select Exceptions tab. Click < Add Program.>. <5> Click <Browse >. <6> Select the following programs under TC-net OPC Server destination folder (Default folder: \Program Files\TOSHIBA\TC_net OPC Server) and Click <Open>. OpcDualMng.exe (OPC Server) (This program is indicated as Start OPC Server in [Add a Program] window.) OpcToolIfSvr.exe (OPC Server) TCnetOPCSvr.exe (OPC Server) C:\Windows\System32\OPCENUM.exe (OPC Server and OPC Client) All of OPC Clients 49

58 3. How to set the environments for connecting OPC <7> On Add a Program window, click <OK>. <8> On Windows Firewall Settings window, confirm whether programs you selected are checked. And if there isn t Microsoft Management Console in the list, add Microsoft Management Program (mmc.exe) under \Windows\System32 folder. (Refer to <4>-<7>) After adding needful programs, click <Add Port >. <9> On Add a Port window, Set the following port and click <OK>. Name : DCOM Port No: 135 Check TCP And add following port likewise. Name : ToolIf Port No: Check TCP 50

59 3. How to set the environments for connecting OPC <10> After adding all needful programs and ports, click <OK>. Figure 3.11 Windows Firewall Setting (Windows Vista/Windows Server 2008) 51

60 3. How to set the environments for connecting OPC On Windows XP / Windows Server 2003 <1> Select [Control Panel]. Click [Windows Firewall]. <2> Windows Firewall is turned on by default. If it is Off, select On (recommended). 52

61 3. How to set the environments for connecting OPC <3>Select Exceptions tab. Click <Add Program >. <4> Select the following programs under TC-net OPC Server destination folder (Default folder: \Program Files\TOSHIBA\TC_net OPC Server) and Click <Open>. OpcDualMng.exe (OPC Server) (This program is indicated as Start OPC Server in [Add a Program] window.) OpcToolIfSvr.exe (OPC Server) TCnetOPCSvr.exe (OPC Server) C:\Windows\System32\OPCENUM.exe (OPC Server and OPC Client) All of OPC Clients On Add a Program window, click <OK>. 53

62 3. How to set the environments for connecting OPC <5> On Windows Firewall window, confirm whether programs you selected are checked. And if there isn t Microsoft Management Console in the list, add Microsoft Management Program (mmc.exe) under \Windows\System32 folder. (Refer to <3>-<4>) After adding needful programs, click <Add Port >. <6> On Add a Port window, Set the following port and click <OK>. Name : DCOM Port No: 135 Check TCP And add following port likewise. Name : ToolIf Port No: Check TCP <7>Click <OK>. Windows Firewall setting is completed. Figure 3.12 Windows Firewall Setting (Windows XP/Windows Server 2003) 54

63 3. How to set the environments for connecting OPC 3.4. User Account Control (Windows 8.1, Windows 7, Windows Vista, Windows Server 2012 R2, Windows Server 2008 R2 and Windows Server 2008 only) User account control (UAC; User Account Control) is one of the security technology introduced in Windows Vista and this is going to let you use Windows in a normal user. When you use PC for OPC Server, it is necessary to invalidate this setting. The user account control becomes by default effective. It is necessary to log on to a change in a user having an Administrator special privilege. How to change the user account control is described below. On Windows 8.1 / Windows Server 2012 R2 <1> On Windows 8.1/Windows Server 2012 R2 Open the menu by right-clicking the left side on the task bar, open the Control Panel. <2> Select "Large icons" or "Small icons" for the view and open Administrative Tools. 55

64 3. How to set the environments for connecting OPC <3> Open Local Security Policy from Administrative Tools. <4> Select the commands in the following order: Security Settings Local Policies Security Options and double click User Account Control: Admin Approval Mode for the Build-in Administrator account. <5> Select Disabled and then click [OK]. Figure 3.13 User Account Control Setting (Windows 8.1/Windows Server 2012 R2) 56

65 3. How to set the environments for connecting OPC On Windows 7 / Windows Server 2008 R2 <1> Open Control Panel from start menu. Select User Accounts and Family Safety. <2>Select User Accounts in the "User Accounts and Family Safety". <2>Select Change User Account Control settings. 57

66 3. How to set the environments for connecting OPC <3> Move the bar to "Never notify" on the scale. Click <OK>. Figure 3.14 User Account Control Setting (Windows 7/Windows Server 2008 R2) On Windows Vista / Windows Server 2008 <1> Open Control Panel from start menu. Select Classic View and open User Accounts. <2>Select Turn User Account Control on or off. 58

67 3. How to set the environments for connecting OPC <3> Use User Account Control (UAC) to help protect your computer is on as default. Uncheck Use User Account Control (UAC) to help protect your computer. Click <OK>. Figure 3.15 User Account Control Setting (Windows Vista/Windows Server 2008) 59

68 3. How to set the environments for connecting OPC 60

69 4. Launch /Close OPC Server 4. Launch / Close OPC Server 4.1 Launch OPC Server This paragraph describes how to launch OPC Sever. After installing OPC Server, Start OPC Server is registered in [Startup]. OPC Server runs automatically when system starts. If you don t want to launch OPC Server automatically, remove it from [Startup]. At this time, you should launch OPC server manually On Windows 8.1/Windows Server 2012 R2 You can remove Start OPC Server from <Startup> as below. (Windows 8.1 only) Open Task Manager and select the <Startup> tab. Select OPC Server Dual Manager and click <Disable> button. Figure 4.1 Remove from [Startup] (Windows 8.1 only) Select the [Start OPC Server] on the App view on Windows 8.1/Windows Server 2012 R2. 61

70 4. Launch /Close OPC Server Figure 4.2 Launch from [App view] On other OS You can remove Start OPC Server from <Startup> as below. Figure 4.3 Remove from [Startup] Select [Start]-[All Programs]-[ TC-net OPC Server]-[Start OPC Server]. Figure 4.4 Launch from [Start]-[All Programs] 62

71 4. Launch /Close OPC Server 4.2 Close OPC Server This paragraph describes about how to close OPC Server. TC-net OPC Server is normally running as minimized status, so its window isn t shown. If you want to close OPC Server, you click TC-net OPC Server and its window is shown. Click X button to close OPC Server. The following message is shown and you click Yes button. After the above processes, the following functions are closed. OPC Server Function, Tool I/F Function, Dual Management, TC-net Access Function 63

72 4. Launch /Close OPC Server Next, You let a Log Save Tool finish. When a Log Save Tool can leave "minimize" or "icon", Restore a screen. When Log Save Tool processing is executing, please click [Stop] button, and click [Close] button next. * : Log Save Tool added in V About TC-net Type The TC-net type (TC-net100 or TC-net1G) that chose at the time of installation of a TC-net OPC server is displayed by a screen title of a TC-net OPC server. When the window of OPC Server isn't shown, you click "TC-net OPC Server" of task bar and it is shown. TC-net Type JTNI : TC-net100 JTGI : TC-net1G 64

73 4. Launch /Close OPC Server 4.4 About Version of OPC Server This paragraph describes about how to find the version of OPC Server. When the window of OPC Server isn't shown, you click "TC-net OPC Server" of task bar and it is shown. Select [Help] [About TC-net OPC Server ], and you can find the version of OPC Server. 4.5 Client Connection Status Select [File] [Client Connection Status], and you can look at a connection state of a OPC client. This screen displays the connected client ID, OPC group name, number of the OPC items. In addition, you can get the log file TCnetOPCSvr.log under the folder which OPC Server is installed in. (Default : C:\Program Files\Toshiba\TC_net OPC Server) 65

74 4. Launch /Close OPC Server 66

75 5. Dual Function 5. Dual Function This chapter describes about dual function. 5.1 Construction and outline Parenthood There are able to be several parent nodes. The own node succeeds (backs up) he talker of the parent node. The child node succeeds (backs up) the talker of the own node. OPC Server (Parent node) OPC Server (Parent node) OPC Server (Own node) OPC Server (Child node) OPC Server (Parent node) The own node monitors the parent node. The own node is monitored by the child node. The child node is only one. Reference: Maximum 10 OPC Servers can exist on the sysytem At the case of two OPC Servers When there are two OPC Servers only, the parent node is the child node. Client Client Client Ethernet OPC Server OPC Server (ST1) (ST2) TC-net nvcon nvcon nvcon nvcon 67

76 5. Dual Function At the case of more than three OPC Servers (1 : 1 Backup) At the case of 1 : 1 backup, when ST1 becomes abnormal, ST2 backups ST1 when ST2 becomes abnormal, ST3 backups ST2. when STn becomes abnormal, ST1 backups STn.. But one node doesn t backup plural nodes. (When ST1 and ST2 become abnormal, ST2 is backed up by ST3 but ST1 isn t backed up by any node. ) -> This system can t support the abnormal status of neighbor nodes. Client Client Client Ethernet OPC Server OPC Server OPC Server OPC Server (ST1) (ST2) (ST3) (STn) TC-net nvcon nvcon nvcon nvcon At the case of more than three OPC Servers (N : 1 Backup) At the case of N : 1 backup, when ST1,ST2 and STn become abnormal, STx backups all abnormal nodes Plural nodes can backup one node. ( When ST1 and ST2 become abnormal, another node backups these two nodes.) Client Client Client Ethernet OPC Server (ST1) OPC Server (ST2) OPC Server (STn) OPC Server (STx) nvcon nvcon nvcon nvcon TC-net 68

77 5. Dual Function Reference: OPC Server doesn t support ths system has both of 1:1 backup and N:1 backup. 5.2 Dual state management The states of OPC Server are described below. 1) INIT : Initializing 2) PRE-ONLINE: Wait for online (The talker is none.) 3) ONLINE: Reading scan data. The talker is only own node s. 4) BACKUP: Reading scan data. The talkers are own node s and parent node s. 5) STANDBY: Reading scan data. The talker is none. It is impossible to write the scan data. 6) STANDBY-LOCK: STANDBY state and locking 7) DOWN: Node down Client Client Client Ethernet Tags specified in the talker can be written. OPC Server (ST1) OPC Server (ST2) Talker : T1 Read Talker : T2 Read TC-net 100 All tags can be nvcon nvcon nvcon always read. nvcon All tags can be always read. Normally, the states of all nodes are ONLINE but when the system detects an error, the state of abnormal node becomes STANDBY. On STANDBY state, it is possible to read scan data normally but impossible to write it. When the parent node and the child node are ONLINE, if the state of the parent node becomes STANDBY, one of the own node becomes BACKUP. On BACKUP state, it is possible to read scan data normally and the talker blocks of the parent node are added to own. At this time, OPC Clients must request the own node to write scan data.. (OPC Clients mustn t request the parent node.) 69

78 5. Dual Function Reference: When ST1 is the state except ONLINE, an OPC Client make access to ST2 with BACKUP state. Client Client Client Ethernet STANDBY or DOWN OPC Server (ST1) Talker : T1+T2 OPC Server (ST2) Read BACKUP TC-net 100 nvcon nvcon nvcon nvcon 70

79 5. Dual Function State Transition Diagram Self TC-net Card Error or TC-net Type Error INIT OPC Server have started. Self TC-net Card Normal and Other Nodes are using talker of self node The following either states occurred. - Self TC-net Card Error - Self TC-net Scan stop - Self TC-net Removed Ring PRE-ONLINE Self TC-net Card Normal and Other Nodes don t use talker of self node. ONLINE All Parent Nodes became PRE_ONLINE, ONLINE or BACKUP BACKUP STANDBY The following either states occurred. - Self TC-net Card Error - Client Application Normal and Other Nodes don t use talker of self node - Self TC-net Scan stop - Self TC-net Removed Ring Including the condition this has several Parent Nodes. Self TC-net Card Normal and Other Nodes are using talker of self node or Client Application Error. DOWN Other States Condition for finishing to backup parent nodes - The state of parent node is PRE_ONLINE, ONLINE or BACKUP. - Other Nodes are using talker of parent nodes. Condition for starting to backup parent nodes Talkers of parent nodes aren t used and one of the following states is occurred. - The state of Parent node is STANDBY or DOWN. - All Talker blocks of parent node is unhealthy. - TC-net Card of parent node is Error. - OPC Server of parent node is unhealthy Shut down request from the OS or the Unhealthy of each task of OPC server *1:"Other Nodes are (not) using talker of self node" means that it is resulted from checking talker blocks registered in self node and not from checking them of parent nodes backed up. *2:"Other Nodes are (not) using talker of parent nodes" means that it is resulted from checking talker blocks of parent node which is or will be backed up. *3: When the state is STANBY and "Other Nodes don't use talker of self node", "Child Node is backing up self node" means that talkers isn't be used. After the state of self node becomes to be normal, it will move to PRE-ONLINE. INIT : Initializing PRE-ONLINE : Wait for online (The talker is none.) ONLINE : Reading scan data. The talker is only own node's. STANDBY : Reading scan data. The talker is none. BACKUP : Reading scan data. The talkers are own node's and parent node's. DOWN : Node down *4: Just after the state has changed, this doesn't detect the duplicate talkers. Therefore if talker is used in other node at that time, the state of self node doesn't immediately move from ORE-ONLINE to STANDBY. *5: For the self node, it is included in "Self TC-net Card Error" that the dual diagnosis counter for network of TC-net has no change. 71

80 6. List of OPC Items 72

81 6. List of OPC Items 6. List of OPC Items 6.1 The List of OPC items Table 6.1 List of OPC items Prefix Item Name Description Data Type Mode Item Name and Data Type are imported from nv Tool. R/W Tcnet ScanMode Scan running state / Start or Stop control VT_UI4 R/W ScanHealthyMap.Block#nnnn Scan healty map [# #2047 / #4095] VT_BOOL RO ClearScanUnHealthyMap Clear scan unhealthy map VT_UI4 R/W ScanSendCycle.HScanCyc High scan transmission cycle VT_UI2 RO ScanSendCycle.MScanCyc Middle scan transmission cycle VT_UI2 RO ScanSendCycle.LScanCyc Low scan transmission cycle VT_UI2 RO ScanSendCycle.MaxNodeDist Maximum distance between nodes VT_UI2 RO ScanSendCycle.MaxRepeater Maximum repeater steps (*1) VT_UI2 RO ScanSendCycle.LoopTotalExt System total length (loop total length), Unit : 1km (*2) VT_UI2 RO ScanSendCycle.MaxUtghJtgiDist Star maximum length, Unit : 0.1km (*2) VT_UI2 RO ScanTalkerBlock.HScan.Block#nnn Scan talker block (High speed) [#000 - #064 / #128] VT_UI2 RO ScanTalkerBlock.MScan.Block#nnn Scan talker block (Middle speed) [#000 - #128 / #256] VT_UI2 RO ScanTalkerBlock.LScan.Block#nnn Scan talker block (Low speed) [#000 - #384 / #640] VT_UI2 RO ScanTalkerMap.Block#nnnn Scan talker map [# #2047 / #4095] VT_UI2 RO ClearScanTalkerMap Clear duplicate blocks of scan talker block map VT_UI4 R/W InringMap.Mac#nnn Inling map [#000 - #255] VT_BOOL RO StationInf.RegInf Station information (Error counter) VT_UI4 RO StationInf.Mac#nnn.MacInf#d Station information [Mac:#000 -#255, Diag:#0 -#3] VT_UI2 RO ClearStationInf Clear station information VT_UI4 R/W DualInf#d Network dual diagnosis counter [#0 - #6] VT_UI4 RO ClearDualInf Clear network dual diagnosis counter VT_UI4 R/W LinkControl Link Control (*1) VT_UI4 R/W Version#d Version information [#0 - #2] VT_UI4 RO Correspondence#d The correspondence acquisition of the rotary switch set value and the card logic number [#0 - #1 / #2] VT_UI2 RO SwitchConfig Dipswitch value VT_UI4 RO HealthyCounter JTNI/JTGI healthy counter VT_UI2 RO RasInfo.Mac#mmm.ContFlag Station(#mmm) controller mounting information [Mac : #000 - #255] - Bit 15-8 : Module type VT_UI2 RO - Bit 7-0 : Controller mounting presence flag RasInfo.Mac#mmm.HealthyCounter Station(#mmm) healty counter VT_UI2 RO RasInfo.Mac#mmm.Alarm Station(#mmm) representation alarm VT_UI2 RO RasInfo.Mac#mmm.Slot#d.HealthyCounter Station(#mmm) slot(#d) healty counter [Slot: #0 - #7] VT_UI2 RO RasInfo.Mac#mmm.Slot#d.ContType Station(#mmm) slot(#d) controller type VT_UI2 RO RasInfo.Mac#mmm.Slot#d.ContSubType Station(#mmm) slot(#d) controller type sub type VT_UI2 RO RasInfo.Mac#mmm.Slot#d.PhaseMode Station(#mmm) slot(#d) phase/mode VT_UI2 RO RasInfo.Mac#mmm.Slot#d.Alarm Station(#mmm) slot(#d) representation alarm VT_UI2 RO (*1) : JTNI (TC-net100) Only, (*2) : JTGI (TC-net1G) Only, R/W : Read/Write, RO : Read Only 73

82 6. List of OPC Items Table 6.1 List of OPC items Prefix Item Name Description Data Type Mode Tcnet RasInfo.Mac#mmm.Stack#sA.OptPort#p. NumOfPackets RasInfo.Mac#mmm.Stack#sA.ElePort. NumOfPackets RasInfo.Mac#mmm.Stack#sB.OptPort#p. NumOfPackets RasInfo.Mac#mmm.Stack#sB.ElePort. NumOfPackets HUB(#mmm) stack(#s) optical port(#p) Number of received packets (A System) (*1) [Stack: #0 - #3] [Port: #1 - #8] HUB(#mmm) stack(#s) Electrical port Number of received packets (A System) (*1) HUB(#mmm) stack(#s) optical port(#p) Number of received packets (B System) (*1) HUB(#mmm) stack(#s) Electrical port Number of received packets (B System) (*1) VT_UI2 VT_UI2 VT_UI2 VT_UI2 RasInfo.Mac#mmm.RasArea.HealthyCounter Healthy counter of a RAS information area VT_UI2 RO TimeInf#d Time information [#0 - #1] (*3) VT_UI4 RO Opc LocalNodeAddr Own node's address (node address on TC-net side) VT_UI2 RO LocalNodeStatus Own node's state (ONLINE/STANDBY/BACKUP etc.) VT_UI2 RO ParentNodeAddr#d Parent node's address for maximum 9 nodes [#0 - #8] VT_UI2 RO ParentNodeStatus#d Parent node's state for maximum 9 nodes [#0 - #8] VT_UI2 RO ChildNodeAddr Child node's address VT_UI2 RO ChildNodeStatus Child node's state VT_UI2 RO BackupNodeAddr#d Parent node's address during backing up for maximum 9 nodes [#0 - #8] VT_UI2 RO OperationTime Running time VT_UI4 RO HealthyCounter Healthy counter VT_UI2 RO DualControl Control dual state (=1 : STANDBY request / =0 : STANDBY release request) VT_UI2 R/W ScanTalkerStatus Duplicate state of talker blocks VT_UI2 RO Client.HealthyCounter#mmm Client Healthy Counter [#000 - #127] = : check it VT_UI2 R/W = 0 : not check Client.Abnormal#mmm Client diagnosis is abnormal [#000 - #127] VT_BOOL RO Client.AbnormalDetect Client abnormal detection state (AND of a diagnosis result for 128 clients) VT_BOOL RO ParentTalkerStatus#d Parent node's duplicate state of talker blocks [#0 - #8] VT_UI2 RO OpcSrv.MemUsed.Current Quantity of memory use of OPC server (Current value) VT_UI4 RO OpcSrv.MemUsed.Average Quantity of memory use of OPC server (Average value) VT_UI4 RO (*1) : JTNI (TC-net100) Only, (*2) : JTGI (TC-net1G) Only, (*3) : JTGI (TC-net1G) and JTNI (PCI Express Card) Only R/W : Read/Write, RO : Read Only RO RO RO RO Reference: Show a meaning of a place described like "[#0000~#nnnn / #gggg]" in lists in the following. - #nnnn : Case of JTNI (TC-net100) - #gggg : Case of JTGI (TC-net1G) Reference: As for the details about "Quantity of memory use of OPC server", please refer to

83 6. List of OPC Items RAS function "Quantity of memory use of OPC server". Reference: After OPC server V01.60, the following items are deleted. - Tcnet.ReportRasUsage - Tcnet.ResetJtni - Opc.DiagStatus Reference: About data structure of a TC-net related item, please refer to an TC-net PCI Bus Card Support Software User's Manual. Reference: In a "Opc.LocalNodeStatus", it is set in the next value. 0 : INIT, 1 : PRE-ONLINE, 2 : ONLINE, 3 : STANDBY, 4 : BACKUP, 5 : DOWN Reference: In a "Opc.ParentNodeStatus#d", it is set in the next value. 0 : INIT, 1 : PRE-ONLINE, 2 : ONLINE, 3 : STANDBY, 4 : BACKUP, 5 : DOWN, 6 : DIAG_ERR, 7 : JTNI/JTGI_ERR DIAG_ERR is set in the case of own node's JTNI/JTGI is normal, and parent node's JTNI/JTGI unhealthy or parent node's OPC server unhealthy. About JTNI/JTGI_ERR, At the time of own node's JTNI/JTGI abnormal, parent node's state is set JTNI/JTGI abnormal. Reference: Station(#mmm) representation alarm (RasInfo.Mac#mmm.Alarm) is logical sum of representation alarm of slot 1-7 (RasInfo.Mac#mmm.Slot#d.Alarm). 75

84 6. List of OPC Items 76

85 7. How to set the environment for OPC Server 7. How to set the environment for OPC Server 7.1 How to set the environment for OPC Server This diagram indicates how to change the environment for OPC Server. This environment is set in TCnetOPCSvr.ini file under the folder which the TC-net100 OPC Server program is installed in. (Default: C:\Program Files\Toshiba\TC_net OPC Server). When you want to change it, you need to open this file by notepad or other tools and edit it. The content of this file TCnetOPCSvr.ini is as below. [General] PortNo=20000 MaxNodeDist=8 MaxRepeater=3 MaxNodeDist1G=10 LoopTotalExt=10 MaxUtghJtgiDist=1 NumTg=100 NumUtgh=4 NumJtgi=12 ParentDiagCount=3 LocalDiagCount=3 ClientDiagCount=30 StateHoldTime=1 StateUpdateTime=1 #DebugMode=1 #PerformanceLog=1 DefAcceWordNum=5 MaxDmaBlockNum=64 HealthyCheckCycle=5 DstScanStopEnable=1 ScanContMoniEnable=1 ScanContMoniTimeout=5 ScanContMoniWaitTime=60 ScanContMoniFloatTime=60 ScanContMoniExecCount=3 PowerMonitorEnable=1 TimeAdjustInterval=00:00 When you change this file, you must restart OPC Server. Important: When you change the environment ( TCnetOPCSvr.ini file), OPC Server may nor run normally accoring to the contents of changes. Please change it carefully. Before you change it, you should copy this file and prepare to recover it. 77

86 7. How to set the environment for OPC Server Set the Port No. for transmission If you want to change the Port No. which the transmission between OPC Server and OPC Server tool uses, you change PortNo parameter in TCnetOPCSvr.ini. file. [General] PortNo=20000 : Set the parameters for TC-net100 If you want to change the parameters for TC-net100, maximum distance between nodes and maximum repeater step number, you change MaxNodeDist parameter and MaxRepeater parameter in TCnetOPCSvr.ini. file. [General] : MaxNodeDist=8 MaxRepeater=3 : --- Maximum distance between nodes, Unit : 0.1km --- maximum repeater step number Set the parameters for TC-net1G If you want to change the parameters for TC-net1G, maximum distance between nodes, System total length and Star maximum length, you change MaxNodeDist1G parameter, LoopTotalExt parameter and MaxUtghJtgiDist parameter in TCnetOPCSvr.ini. file. And set number of TG823/UTGH23/JTGI23 in a system in "NumTg", "NumUtgh" and "NumJtgi" parameter. [General] : MaxNodeDist1G= Maximum distance between nodes, Unit : 0.1km LoopTotalExt= System total length, Unit : 1km MaxUtghJtgiDist=1 --- Star maximum length, Unit : 0.1km NumTg= Number of TG823 in a system NumUtgh=4 --- Number of UTGH23 in a system NumJtgi= Number of JTGI23 in a system : Set the diagnosis time 78 If you want to change the diagnosis time that the function switching dual state has, you change ParentDiagCount parameter, LocalDiagCount parameter and ClientDiagCount parameter in TCnetOPCSvr.ini. file. ParentDiagCount : This is the time to diagnose the healthy of JTNI of the parent nodes and OPC Server. (per Sec)

87 7. How to set the environment for OPC Server LocalDiagCount : This is the time to diagnose the healthy of the self node. (per Sec) ClientDiagCount : This is the time to diagnose the healthy of the OPC Clients. (per Sec) [General] : ParentDiagCount=3 LocalDiagCount=3 ClientDiagCount=30 : Set the Dual state management If you want to change an action of the function switching dual state has, you change StateHoldTime parameter and StateUpdateTime parameter in TCnetOPCSvr.ini. file. StateHoldTime: This is the time that holds an PRE-ONLINE, ONLINE and BACKUP state. (per Sec) StateUpdateTime: This is the transfer time of the dual state and healthy counter of the OPC Server. (per 100msec) [General] : StateHoldTime=1 StateUpdateTime=1 : 79

88 7. How to set the environment for OPC Server Set the simulation mode If you want to use the function of OPC Server when your pc doesn t have TC-net PCI Bus card (JTNI/JTGI series), you set the simulation mode. But you need the TC-net 100/1G PCI Bus Card Support Software. Important: You can set the simulation mode only when you test OPC Server or OPC Client. When the system runs actually, you must recover this content. (1) How to set You change DebugMode parameter in TCnetOPCSvr.ini. file. [General] : #DebugMode=1 * : * : You delete the head character #, edit as below and save. [General] : DebugMode=1 : (2) Restart TC-net100 OPC Server You restart OPC Server and click TC-net OPC Server Dual Manage icon in the task bar. The TC-net OPC Server Dual Manager dialog is shown as below. 80

89 7. How to set the environment for OPC Server *1 *5 *4 *2 *3 *6 As the history indicates like (*1), you wait that the dual state has moved to PRE_ONLINE, ONLINE or BACKUP after it connected OPC Server. (3) Change the diagnosis states In the TC-net OPC Server Dual Manager dialog, the content of (*2) indicates the following state. JTNI/JTGI UnHealthy (Status) The status of JTNI/JTGI is Unhealthy Client UnHealthy (Status) The status of OPC Client is Unhealthy Talker Block Used (Status) Talkers of self node are duplicate or not By setting ON in the check box (*3), you can change the state shown in (*2). JTNI/JTGI Healthy Make JTNI/JTGI Healthy. No Check Client UnHealthy Not check OPC Client s healthy. No Check Talker Block Used Not check whether or not Talkers of self node are duplicate. (**1) Set Talker Block Used Make the Talkers of self node duplicate. For example, when the state is JTNI/JTGI UnHealthy (Status) in (*2) and you would like to change this to Healthy, you set ON to the check box of JTNI /JTGI Healthy in (*3). 81

90 7. How to set the environment for OPC Server You set ON or OFF to the check box in (*3) and set OFF to all items in (*2). You can make the dual state move to ONLINE. (**1)It may take several seconds. (About 20 seconds) (4) Change the TC-net node address The initial value of TC-net node address is 2 as (*4) indicates. When you need to change the node address, you can change it in (*5). *5 (5) Change the dual state By the operation (*6), you can make the dual state move to other states forcedly or reset it. *6 (6) Change a healthy state of scan data Click TC-net Control/Scan Task icon in the task bar. The following dialog is shown. By setting ON or OFF in the check box (*7), you can change a healthy state of scan data. 82

91 7. How to set the environment for OPC Server *7 (7) The simulation output of TC-net items and OPC items Action in a simulation mode of TC-net items and OPC items are described below. Simulation data are classified as follows. R(Sim)/W : Simulation data begin to be read. Start increment of Simulation data when OPC Client write in 1. Stop increment of Simulation data when OPC Client write in 0. R/W(Sim) : When OPC Client write in even once. That value begins to be read. A value using by TC-net OPC Server Dual Manager is not changed. When remove a simulation mode, you must restart OPC Server. 83

92 7. How to set the environment for OPC Server Reading and writing action mode of TC-net items and OPC items in a simulation mode in the following. The item that a Mode column is gray shows that an action is different from a normal mode. Table 7.1 List of OPC items (simulation mode) Prefix Item Name Description Data Type Mode Item Name and Data Type are imported from nv Tool. R/W Tcnet ScanMode Scan running state / Start or Stop control VT_UI4 R/W ScanHealthyMap.Block#nnnn Scan healty map [# #2047 / #4095] VT_BOOL R/W ClearScanUnHealthyMap Clear scan healthy map VT_UI4 R/W ScanSendCycle.HScanCyc High scan transmission cycle VT_UI2 RO ScanSendCycle.MScanCyc Middle scan transmission cycle VT_UI2 RO ScanSendCycle.LScanCyc Low scan transmission cycle VT_UI2 RO ScanSendCycle.MaxNodeDist Maximum distance between nodes VT_UI2 RO ScanSendCycle.MaxRepeater Maximum repeater steps VT_UI2 RO ScanSendCycle.LoopTotalExt System total length (loop total length), Unit : 1km VT_UI2 RO ScanSendCycle.MaxUtghJtgiDist Star maximum length, Unit : 0.1km VT_UI2 RO ScanTalkerBlock.HScan.Block#nnn Scan talker block (High speed) [#000 - #064 / #128] VT_UI2 RO ScanTalkerBlock.MScan.Block#nnn Scan talker block (Middle speed) [#000 - #128 / #256] VT_UI2 RO ScanTalkerBlock.LScan.Block#nnn Scan talker block (Low speed) [#000 - #384 / #640] VT_UI2 RO ScanTalkerMap.Block#nnnn Scan talker map [# #2047 / #4095] VT_UI2 R/W ClearScanTalkerMap Clear duplicate blocks of scan talker block map VT_UI4 R/W InringMap.Mac#nnn Inling map [#000 - #255] VT_BOOL R/W StationInf.RegInf Station information (Error counter) VT_UI4 R/W StationInf.Mac#nnn.MacInf#d Station information [Mac:#000 -#255, Diag:#0 -#3] VT_UI2 R/W ClearStationInf Clear station information VT_UI4 R/W DualInf#d Network dual diagnosis counter [[#0, #3 - #6] VT_UI4 R/W DualInf#1 Network dual diagnosis counter (A Bus Normal Count) VT_UI4 R(Sim)/W DualInf#2 Network dual diagnosis counter (B Bus Normal Count) VT_UI4 R(Sim)/W ClearDualInf Clear network dual diagnosis counter VT_UI4 R/W LinkControl Link Control VT_UI4 R/W Version#d Version information [#0 - #2] VT_UI4 R/W Correspondence#d The correspondence acquisition of the rotary switch set value and the card logic number [#0 - #1 / #2] VT_UI2 R/W SwitchConfig Dipswitch value VT_UI4 RO HealthyCounter JTNI/JTGI healthy counter VT_UI2 R(Sim)/W RasInfo.Mac#mmm.ContFlag Station(#mmm) controller mounting information [Mac : #000 - #255] - Bit 15-8 : Module type VT_UI2 R/W - Bit 7-0 : Controller mounting presence flag RasInfo.Mac#mmm.HealthyCounter Station(#mmm) healty counter VT_UI2 R(Sim)/W RasInfo.Mac#mmm.Alarm Station(#mmm) representation alarm VT_UI2 R/W RasInfo.Mac#mmm.Slot#d.HealthyCounter Station(#mmm) slot(#d) healty counter [Slot: #0 - #7] VT_UI2 R(Sim)/W RasInfo.Mac#mmm.Slot#d.ContType Station(#mmm) slot(#d) controller type VT_UI2 R/W RasInfo.Mac#mmm.Slot#d.ContSubType Station(#mmm) slot(#d) controller type sub type VT_UI2 R/W RasInfo.Mac#mmm.Slot#d.PhaseMode Station(#mmm) slot(#d) phase/mode VT_UI2 R/W RasInfo.Mac#mmm.Slot#d.Alarm Station(#mmm) slot(#d) representation alarm VT_UI2 R/W 84

93 7. How to set the environment for OPC Server Table 7.1 List of OPC items (simulation mode) Prefix Item Name Description Data Type Mode Tcnet RasInfo.Mac#mmm.Stack#sA.OptPort#p. NumOfPackets RasInfo.Mac#mmm.Stack#sA.ElePort. NumOfPackets RasInfo.Mac#mmm.Stack#sB.OptPort#p. NumOfPackets RasInfo.Mac#mmm.Stack#sB.ElePort. NumOfPackets HUB(#mmm) stack(#s) optical port(#p) Number of received packets (A System) [Stack: #0 - #3] [Port: #1 - #8] HUB(#mmm) stack(#s) Electrical port Number of received packets (A System) HUB(#mmm) stack(#s) optical port(#p) Number of received packets (B System) HUB(#mmm) stack(#s) Electrical port Number of received packets (B System) VT_UI2 VT_UI2 VT_UI2 VT_UI2 R(Sim)/W R(Sim)/W R(Sim)/W R(Sim)/W RasInfo.Mac#mmm.RasArea.HealthyCounter Healthy counter of a RAS information area VT_UI2 R(Sim)/W TimeInf#d Time information [#0 - #1] VT_UI4 RO Opc LocalNodeAddr Own node's address (node address on TC-net side) VT_UI2 R/W(Sim) LocalNodeStatus Own node's state (ONLINE/STANDBY/BACKUP etc.) VT_UI2 R/W(Sim) ParentNodeAddr#d Parent node's address for maximum 9 nodes [#0 - #8] VT_UI2 R/W(Sim) ParentNodeStatus#d Parent node's state for maximum 9 nodes [#0 - #8] VT_UI2 R/W(Sim) ChildNodeAddr Child node's address VT_UI2 R/W(Sim) ChildNodeStatus Child node's state VT_UI2 R/W(Sim) BackupNodeAddr#d Parent node's address during backing up for maximum 9 nodes [#0 - #8] VT_UI2 R/W(Sim) OperationTime Running time VT_UI4 RO HealthyCounter Healthy counter VT_UI2 R(Sim)/W DualControl Control dual state (=1 : STANDBY request / =0 : STANDBY release VT_UI2 R/W request) ScanTalkerStatus Duplicate state of talker blocks VT_UI2 R/W(Sim) Client.HealthyCounter#mmm Client Healthy Counter [#000 - #127] = : check it VT_UI2 R(Sim)/W = 0 : not check Client.Abnormal#mmm Client diagnosis is abnormal [#000 - #127] VT_ BOOL R/W(Sim) Client.AbnormalDetect Client abnormal detection state (AND of a diagnosis result for 128 clients) VT_ BOOL R/W(Sim) ParentTalkerStatus#d Parent node's duplicate state of talker blocks [#0 - #8] VT_UI2 R/W(Sim) OpcSrv.MemUsed.Current Quantity of memory use of OPC server (Current value) VT_UI4 RO OpcSrv.MemUsed.Average Quantity of memory use of OPC server (Average value) VT_UI4 RO * In an item of "RasInfo.Mac#mmm", Start/Stop increment of Simulation data is done every station collectively. 85

94 7. How to set the environment for OPC Server Set Log Output of JTNI/JTGI Scan Memory Acccess Performance When the number of the access words in one block is more than the prescribed value (default : 5), the reading process the scan memory of TC-net 100 PCI Bus Card (JTNI PCI Card) has access to one block data without doing it by word unit. In addition, the reading process the scan memory of a TC-net 100 PCI Express Bus Card (JTNI PCI Express Card) and TC-net 1G PCI Bus Card (JTGI) always does access by a block unit. You set a parameter to be able to read data (scan memory access performance value) which serve as a reference when you coordinate this prescribed value. You change PerformanceLog parameter in TCnetOPCSvr.ini file. [General] : #PerformanceLog=1 * : * : You delete the head character #, edit as below and save. [General] : PerformanceLog=1 : Important: About how to put out log of JTNI/JTGI scan memory access performance, please refer to 7.2 Output Log of Scan Memory Access Performance. You can set this parameter only when you test OPC Server. When the system runs actually, you must recover this content. Change the prescribed value of JTNI (PCI Card) Scan Memory Access Performance When you change the prescribed value of the access words per one block after checking the log described in 7.2, you change DefAcceWordNum parameter in TCnetOPCSvr.ini file. [General] : DefAcceWordNum=5 86

95 7. How to set the environment for OPC Server Change the prescribed value of JTNI (PCI Express Card) and JTGI Scan Memory Access Performance When you change the prescribed value of the maximum block number of JTNI (PCI Express Card) and JTGI, you change MaxDmaBlockNum parameter in TCnetOPCSvr.ini file. [General] : MaxDmaBlockNum =64 Change of diagnosis time of each task of an OPC server When you change diagnosis time of each task (TCnetOPCSvr.exe, OpcDualMng.exe, TCnetScanCtrl.exe, OpcToolIfSvr.exe) of an OPC server, you change HealthyCheckCycle parameter in TCnetOPCSvr.ini file. A prescribed value is five seconds. When set 0, each task of OPC server do not check it. [General] : HealthyCheckCycle=5 --- Diagnosis time, Unit : sec Change of enable or disable of request to stop of the scan transmission of other station In the case of TC-net1G(JTGI), OPC Server can require to stop of the scan transmission of other station. When you change to disable to this action, you change "DstScanStopEnable" parameter in "TCnetOPCSvr.ini" file. The details please refer chapter 10 RAS functions. [General] : DstScanStopEnable = : Enable, 0 : Disable 87

96 7. How to set the environment for OPC Server Change of enable or disable of monitor function of continuation request of the scan transmission of own station In the case of TC-net100(JTNI PCI Express Card) and TC-net1G(JTGI), there is a monitor function of continuation request of the scan transmission of own station. When you change this function, you change "ScanContMoniEnable" parameter, "ScanContMoniTimeout" parameter or "ScanContMoniWaitTime" parameter in "TCnetOPCSvr.ini" file. The details please refer chapter 10 RAS functions. [General] : ScanContMoniEnable = : Enable, 0 : Disable ScanContMoniTimeout=5 --- Monitor time, Unit : sec ScanContMoniWaitTime= Fixed wait time to a start of WDT, Unit : sec ScanContMoniFloatTime= Floarting wait time to a start of WDT, Unit : sec ScanContMoniExecCount=3 --- Execution number of times of WDT reset processing Change of enable or disable of power supply monitor function of own station In the case of TC-net100(JTNI PCI Express Card) and TC-net1G(JTGI), there is a power supply monitor function of own station. When you change to disable to this function, you change "PowerMonitorEnable" parameter in "TCnetOPCSvr.ini" file. The details please refer chapter 10 RAS functions. [General] : PowerMonitorEnable= : Enable, 0 : Disable 88

97 7. How to set the environment for OPC Server Setting of time adjusting interval with TC-net In the case of TC-net100(JTNI PCI Express Card) and TC-net1G(JTGI), there is a function to adjust the date/time of OPC server at the date/time of a TC-net system. When you change to enable to this function, you change "TimeAdjustInterval" parameter in "TCnetOPCSvr.ini" file. The details please refer chapter 7.3 Time adjusting function with TC-net. [General] : TimeAdjustInterval=00: :00 : Disable Specify an execution interval of time adjusting in 1-30 minutes or 1-24 hours. When you want to execute it every 1-30 minutes, you change it as follows. [General] : TimeAdjustInterval=00:mm --- mm : (minutes) When divide progress time (minutes) from 00:00 by this setting value, and a remainder became 0, execute adjustment of the time. When you want to execute it every 1-24 hours, you change it as follows. [General] : TimeAdjustInterval=hh: hh : (hours) When divide progress time (hours) from 00:00 by this setting value, and a remainder became 0, execute adjustment of the time. Important: "Time adjusting function with TC-net" added in TC-net OPC Server V

98 7. How to set the environment for OPC Server 7.2 Log Output of Scan Memory Access Performance This diagram indicates how to put out log of JTNI/JTGI scan memory access performance and the contents. Before this process, you must set PerformanceLog parameter described in Set Log Output of JTNI/JTGI Scan Memory Acccess Performance of 7.1 and restart OPC Server. (1) How to put out the log Click TC-net Control/Scan Task icon in the task bar. The following dialog is shown. Click [Acce Info] button. By clicking [Acce Info] button, you can get the log file TCnetScanCtrl.log under the folder which OPC Server is installed in. (Default : C:\Program Files\Toshiba\TC_net OPC Server) After checking the contents of the log file, click [Minimize] button in the title bar of this dialog. Don t click [Exit] button or [Close] button. 90

99 7. How to set the environment for OPC Server (2) Contents of Log (JTNI PCI Card) The sample of log in case of TC-net100(JTNI PCI Card) is described below. (The sample of C:\Program Files\Toshiba\TC_net OPC Server\TCnetScanCtrl.log ) Thu Feb 19 11:26: Access Log Thu Feb 19 11:26:31 - DateTime = 2009/2/19 11:26:31 Thu Feb 19 11:26:31 - AcceWordNum = Current setting value of JTNI scan memory access Thu Feb 19 11:26:31 - ReadInterval, BlockNum, WordNum, ProcMax, ProcMin, ProcAve, IntervalMax, IntervalMin, IntervalAve Thu Feb 19 11:26:31-100, 561( 8976), 0, 32000, 15000, 24000, 125, 120, 122 Thu Feb 19 11:26:31-200, 3( 48), 0, 32000, 15000, 24000, 245, 210, 228 Thu Feb 19 11:26:31-300, 4( 64), 0, 32000, 15000, 22000, 375, 350, 368 *1 Thu Feb 19 11:26:31-500, 7( 112), 0, 32000, 15000, 23000, 588, 580, 581 Thu Feb 19 11:26:33 - AcceWordNum = 2, BlockNum = 2000, WordNum = 0, ProcTime = Thu Feb 19 11:26:33 - AcceWordNum = 4, BlockNum = 2000, WordNum = 0, ProcTime = Thu Feb 19 11:26:34 - AcceWordNum = 6, BlockNum = 2000, WordNum = 0, ProcTime = Thu Feb 19 11:26:35 - AcceWordNum = 8, BlockNum = 2000, WordNum = 0, ProcTime = Thu Feb 19 11:26:36 - AcceWordNum = 10, BlockNum = 2000, WordNum = 0, ProcTime = Thu Feb 19 11:26:37 - AcceWordNum = 12, BlockNum = 2000, WordNum = 0, ProcTime = Thu Feb 19 11:26:38 - AcceWordNum = 14, BlockNum = 2000, WordNum = 0, ProcTime = Thu Feb 19 11:26:39 - AcceWordNum = 16, BlockNum = 2000, WordNum = 0, ProcTime = Thu Feb 19 11:26:39 - AcceWordNum = 18, BlockNum = 0, WordNum = 32000, ProcTime = Thu Feb 19 11:26:40 - AcceWordNum = 20, BlockNum = 0, WordNum = 32000, ProcTime = Thu Feb 19 11:26:40 - AcceWordNum = 22, BlockNum = 0, WordNum = 32000, ProcTime = Thu Feb 19 11:26:41 - AcceWordNum = 24, BlockNum = 0, WordNum = 32000, ProcTime = Thu Feb 19 11:26:41 - AcceWordNum = 26, BlockNum = 0, WordNum = 32000, ProcTime = Thu Feb 19 11:26:42 - AcceWordNum = 28, BlockNum = 0, WordNum = 32000, ProcTime = Thu Feb 19 11:26:42 - AcceWordNum = 30, BlockNum = 0, WordNum = 32000, ProcTime = Thu Feb 19 11:26:43 - AcceWordNum = 32, BlockNum = 0, WordNum = 32000, ProcTime = Thu Feb 19 11:26:43 - AcceWordNum = 34, BlockNum = 0, WordNum = 32000, ProcTime = *2 Thu Feb 19 11:26:44 - AcceWordNum = 36, BlockNum = 0, WordNum = 32000, ProcTime = Thu Feb 19 11:26:44 - AcceWordNum = 38, BlockNum = 0, WordNum = 32000, ProcTime = Thu Feb 19 11:26:45 - AcceWordNum = 40, BlockNum = 0, WordNum = 32000, ProcTime = Thu Feb 19 11:26:45 - AcceWordNum = 42, BlockNum = 0, WordNum = 32000, ProcTime = Thu Feb 19 11:26:46 - AcceWordNum = 44, BlockNum = 0, WordNum = 32000, ProcTime = Thu Feb 19 11:26:46 - AcceWordNum = 46, BlockNum = 0, WordNum = 32000, ProcTime = Thu Feb 19 11:26:46 - AcceWordNum = 48, BlockNum = 0, WordNum = 32000, ProcTime = Thu Feb 19 11:26:47 - AcceWordNum = 50, BlockNum = 0, WordNum = 32000, ProcTime = Thu Feb 19 11:26:47 - AcceWordNum = 52, BlockNum = 0, WordNum = 32000, ProcTime = Thu Feb 19 11:26:48 - AcceWordNum = 54, BlockNum = 0, WordNum = 32000, ProcTime = Thu Feb 19 11:26:48 - AcceWordNum = 56, BlockNum = 0, WordNum = 32000, ProcTime = Thu Feb 19 11:26:49 - AcceWordNum = 58, BlockNum = 0, WordNum = 32000, ProcTime = Thu Feb 19 11:26:49 - AcceWordNum = 60, BlockNum = 0, WordNum = 32000, ProcTime = Thu Feb 19 11:26:50 - AcceWordNum = 62, BlockNum = 0, WordNum = 32000, ProcTime = Thu Feb 19 11:26:50 - AcceWordNum = 64, BlockNum = 0, WordNum = 32000, ProcTime = Thu Feb 19 11:26: Performance Log End. In *1 area, the following information is written. 91

100 7. How to set the environment for OPC Server - Reading Cycle which is set per block. - The Number of blocks accessed per block (This is number of words.) - The Number of words accessed per word - Maximum, Minimum and Average of time which is taken to do the process (Unit : micro second) - Maximum, Minimum and Average of time which is taken to read actually (Unit : ms) In *2 area, the following information is written. - The Number of blocks accessed per block when you make the setting value of Scan memory access move from 2 to 64 - The Number of words accessed per word when you make the setting value of Scan memory access move from 2 to 64 - The Time for the procedure (Unit : micro second) The setting value AcceWordNum of Scan memory access is one in the line where the value of ProcTime parameter is the minimum. According to the above sample, ProcTime parameter in the line with underline is minimum (32000) and so you use the AcceWordNum = 18 here. About how to change the setting value, please refer to Change the prescribed value of JTNI (PCI Card) Scan Memory Access Performance of

101 7. How to set the environment for OPC Server (3) Contents of Log (JTNI PCI Express Card and JTGI) The sample of log in case of TC-net100(JTNI PCI Express Card) and TC-net1G(JTGI) is described below. (The sample of C:\Program Files\Toshiba\TC_net OPC Server\TCnetScanCtrl.log ) Mon Apr 11 11:26: Access Log Mon Apr 11 11:26:31 - DateTime = 2011/4/11 11:26:31 Mon Apr 11 11:26:31 - DmaBlockNum = Current setting value of JTGI scan memory access Mon Apr 11 11:26:31 - ReadInterval, BlockNum, ProcMax, ProcMin, ProcAve, IntervalMax, IntervalMin, IntervalAve Mon Apr 11 11:26:31-110, 369( 8786), 3775, 719, 3332, 125, 96, 109 Mon Apr 11 11:26:31-200, 6( 384), 1763, 399, 1022, 213, 192, 202 *1 Mon Apr 11 11:26:31-300, 6( 384), 1126, 398, 690, 326, 297, 311 Mon Apr 11 11:26:31-400, 6( 384), 1030, 398, 511, 417, 392, 405 Mon Apr 11 11:26:31 - DmaBlockNum = 8, BlockNum = 163, AcceNum = 23, ProcTime = 5575 Mon Apr 11 11:26:31 - DmaBlockNum = 16, BlockNum = 163, AcceNum = 14, ProcTime = 4782 Mon Apr 11 11:26:31 - DmaBlockNum = 24, BlockNum = 179, AcceNum = 12, ProcTime = 4776 Mon Apr 11 11:26:31 - DmaBlockNum = 32, BlockNum = 163, AcceNum = 10, ProcTime = 4678 Mon Apr 11 11:26:31 - DmaBlockNum = 40, BlockNum = 171, AcceNum = 10, ProcTime = 4704 Mon Apr 11 11:26:31 - DmaBlockNum = 48, BlockNum = 179, AcceNum = 9, ProcTime = 4707 Mon Apr 11 11:26:31 - DmaBlockNum = 56, BlockNum = 187, AcceNum = 9, ProcTime = 4678 Mon Apr 11 11:26:31 - DmaBlockNum = 64, BlockNum = 195, AcceNum = 9, ProcTime = 4636 Mon Apr 11 11:26:31 - DmaBlockNum = 72, BlockNum = 203, AcceNum = 9, ProcTime = 4658 Mon Apr 11 11:26:32 - DmaBlockNum = 80, BlockNum = 211, AcceNum = 9, ProcTime = 4695 Mon Apr 11 11:26:32 - DmaBlockNum = 88, BlockNum = 219, AcceNum = 9, ProcTime = 5114 Mon Apr 11 11:26:32 - DmaBlockNum = 96, BlockNum = 227, AcceNum = 8, ProcTime = 4527 Mon Apr 11 11:26:32 - DmaBlockNum = 104, BlockNum = 235, AcceNum = 8, ProcTime = 4543 Mon Apr 11 11:26:32 - DmaBlockNum = 112, BlockNum = 243, AcceNum = 8, ProcTime = 4576 Mon Apr 11 11:26:32 - DmaBlockNum = 120, BlockNum = 251, AcceNum = 8, ProcTime = 4645 Mon Apr 11 11:26:33 - DmaBlockNum = 128, BlockNum = 259, AcceNum = 8, ProcTime = 4659 Mon Apr 11 11:26:33 - DmaBlockNum = 136, BlockNum = 267, AcceNum = 8, ProcTime = 4690 Mon Apr 11 11:26:33 - DmaBlockNum = 144, BlockNum = 275, AcceNum = 8, ProcTime = 4661 Mon Apr 11 11:26:33 - DmaBlockNum = 152, BlockNum = 283, AcceNum = 8, ProcTime = 4719 Mon Apr 11 11:26:33 - DmaBlockNum = 160, BlockNum = 291, AcceNum = 8, ProcTime = 4671 Mon Apr 11 11:26:33 - DmaBlockNum = 168, BlockNum = 299, AcceNum = 8, ProcTime = 4708 Mon Apr 11 11:26:34 - DmaBlockNum = 176, BlockNum = 307, AcceNum = 8, ProcTime = 4702 Mon Apr 11 11:26:34 - DmaBlockNum = 184, BlockNum = 315, AcceNum = 8, ProcTime = 4673 Mon Apr 11 11:26:34 - DmaBlockNum = 192, BlockNum = 323, AcceNum = 8, ProcTime = 4683 Mon Apr 11 11:26:34 - DmaBlockNum = 200, BlockNum = 331, AcceNum = 8, ProcTime = 4745 Mon Apr 11 11:26:34 - DmaBlockNum = 208, BlockNum = 339, AcceNum = 8, ProcTime = 4728 Mon Apr 11 11:26:34 - DmaBlockNum = 216, BlockNum = 347, AcceNum = 8, ProcTime = 4679 Mon Apr 11 11:26:34 - DmaBlockNum = 224, BlockNum = 355, AcceNum = 8, ProcTime = 4724 Mon Apr 11 11:26:35 - DmaBlockNum = 232, BlockNum = 363, AcceNum = 8, ProcTime = 4692 Mon Apr 11 11:26:35 - DmaBlockNum = 240, BlockNum = 371, AcceNum = 8, ProcTime = 4691 Mon Apr 11 11:26:35 - DmaBlockNum = 248, BlockNum = 379, AcceNum = 8, ProcTime = 4721 Mon Apr 11 11:26:35 - DmaBlockNum = 256, BlockNum = 387, AcceNum = 8, ProcTime = 4711 Mon Apr 11 11:26: Performance Log End. *2 93

102 7. How to set the environment for OPC Server In *1 area, the following information is written. - Reading Cycle which is set per block. - The Number of blocks accessed per block (This is number of words.) - Maximum, Minimum and Average of time which is taken to do the process (Unit : micro second) - Maximum, Minimum and Average of time which is taken to read actually (Unit : ms) In *2 area, the following information is written. - The Number of blocks accessed per block when you make the setting value of Scan memory access move from 8 to The Number of accessed when you make the setting value of Scan memory access move from 8 to The Time for the procedure (Unit : micro second) The setting value DmaBlockNum of Scan memory access is one in the line where the value of ProcTime parameter is the minimum. According to the above sample, ProcTime parameter in the line with underline is minimum (4527) and so you use the DmaBlockNum = 96 here. About how to change the setting value, please refer to Change the prescribed value of JTNI (PCI Express Card) and JTGI Scan Memory Access Performance of

103 7. How to set the environment for OPC Server 7.3 Time adjusting function with TC-net When used TC-net100(JTNI PCI Express Card) or TC-net1G(JTGI), this chapter describes a function of adjust date/time of OPC server at the date/time of TC-net system. Do "Setting of time adjusting interval with TC-net" of 7.1 "How to set the environment for OPC Server" beforehand, and please reboot OPC server. (1) Time adjusting function At intervals of the execution that specified in "Setting of time adjusting interval with TC-net" of 7.1 "How to set the environment for OPC Server", begin to read the date/time from TC-net system and adjust the date/time of OPC server. About an execution interval, please refer to "Setting of time adjusting interval with TC-net" of 7.1 "How to set the environment for OPC Server". (2) Time adjusting processing When never set the date/time in TC-net system, date/time that has begun to read from a TC-net system is wrong. On this account, do not adjust the date/time of OPC Server when compare the date/time of TC-net system and OPC Server, and there was a difference more than one month (longer from 31 days). In this case the following log is output to log file (TCnetScanCtrl.log) Example) Year and month of TC-net are different from the Current time. PC [2012/02/15] / TC-net [2034/01/01] In addition, the time does not adjust the date/time of PC in case of 00:00 so that "day" does not change as much as possible. But, in the case of execution interval specification for 1-24 hours, adjust the date/time five minutes later. Execution log of date/time adjusting does not output it whenever adjust the date/time. When differences of the date/time of TC-net system and OPC Server are more than one minute, output it in log file. Following log is output to log file (TCnetScanCtrl.log) Example) TC-net Date/Time Adjust Execute. : 2012/02/15 11:10: > 2012/02/15 11:11: Important: "Time adjusting function with TC-net" added in TC-net OPC Server V

104 7. How to set the environment for OPC Server 96

105 8. Log Save Tool 8. Log Save Tool 8.1 Outline of Log Save Tool Log Save Tool compresses a log file (four follows) of each OPC server function and saves it in a specified period, hard disk. (1) OPC Server Function (Log file : TCnetOPCSvr.log, TCnetOPCSvr.org) (2) Dual Management Function (Log file : OpcDualMng.log, OpcDualMng.org) (3) TC-net Access Function (Log file : TCnetScanCtrl.log, TCnetScanCtrl.org) (4) Tool I/F Function (Log file : OpcToolIfSvr.log, OpcToolIfSvr.org) When file size exceeds 1MB a current log file (extension : log), extension is changed to "org" from "log". Log Save Tool detects that extension of this log file changed and executes compression processing. Log Save Tool change a file name before compressing it. (extension : org -> txt) Show an example of a file name in the following. File name : TCnetOPCSvr_ _ txt, OpcDualMng_ _ txt etc. Top date/time of stored by log file. "yymmdd-hhmmss" Last date/time. "yymmdd-hhmmss" In addition, at a point in time when a stop of log save process or date changed into, copy a current log file (extension : log), and compression processes after changing a file name. Log file compresses a period of 1 day in one file and saves it. Show an example of a name of a compressed file in the following. (extension : cmp) Compressed file : OPCSvrLogs_ cmp The previous day or the day that a log save stopped. yymmdd * : Log Save Tool added in V

106 8. Log Save Tool 8.2 Launch / Close Log Save Tool Launch Log Save Tool After installing TC-net OPC Server, Log Save Tool is registered in [Startup]. Log Save Tool runs automatically when system starts. (*1) At this time, you should launch Log Save Tool manually. Select the [Log Save Tool] on the App view on Windows 8.1/Windows Server 2012 R2. Select [Start]-[All Programs]-[ TC-net Opc Server]-[ Log Save Tool] on other OS. (*2) On Windows 8.1/Windows Server 2012 R2 You can remove Log Save Tool from <Startup> as below. (Windows 8.1 only) Open Task Manager and select the <Startup> tab. Select Log Save Tool and click <Disable> button. Figure 8.1 Remove from [Startup] (Windows 8.1 only) Select the [Log Save Tool] on the App view on Windows 8.1/Windows Server 2012 R2. 98

107 8. Log Save Tool Figure 8.2 Launch from [App view] On other OS *1 *2 Figure 8.3 Remove from [Startup] / Launch from [Start]-[All Programs] 99

108 8. Log Save Tool Close Log Save Tool When a Log Save Tool can leave "minimize" or "icon", Restore a screen. *1 *2 When Log Save Tool processing is executing, please click [Stop] button (*1), and click [Close] button (*2) next. 100

109 8. Log Save Tool 8.3 Screen / Operation instructions Screen instructions 1) 2) 3) 4) 5) 6) 7) 8) 9) 1) Save Folder Specify folder of compressed log file. Click [Browse...] button and can select a folder. Default folder is " C:\Program Files\Toshiba\TC_net OPC Server\Logs ". 2) Save Condition / Save Period Choose a Save Period from a combo box or input it by manual operation. Input range is from 1 day to 365 days. Default is 90 days. When over the save period that specified, an old file is deleted. 3) Stop Condition / Disk Space Capacity Choose a Disk Space Capacity from a combo box or input it by manual operation. 101

110 8. Log Save Tool Input range is from 1 GB to 100 GB. Default is 1 GB. Log save process checks free space capacity of save disk (drive) periodically. If free space capacity became less than capacity that specified here, log save process is stop automatically. When log save process stopped automatically, message box is displayed. 4) Current State Update indication of a current save period (days), save capacity and free space capacity of save disk (drive) by periodically (about 5 seconds). 5) Indication of a processing status Display a processing status such as a log save execution state. 6) [Start] button [Start] button to start log save processing. When processing executes it, an icon is displayed in a Notification Icons of Taskbar. When an icon is shown a Notification Icons of Taskbar, I show that log save processing is executing it. 7) [Stop] button [Stop] button to stop log save processing. 8) [Decomp...] button [Decomp...] button to decompress long-term save log file (file which was compressed). 102

111 8. Log Save Tool While execute of decompress, lock of "log save process (log compress process)". Therefore, during this processing, new log file is not lost. The details please refer to "8.4. Decompress log files". Important: While execute of decompress, OPC server becomes slow and update period of data may become long. About a how to decompress log file with the machine which OPC server is not installed in, please refer to Chapter 9. 9) [Close] button [Close] button to close a setting screen of "Log Save Tool". When long-term save processing is execution even if this setting screen is closed, it is executed in background. An icon is displayed in a Notification Icons of Taskbar. When long-term save processing is stop, the following inquiries are displayed. 103

112 8. Log Save Tool Operation instructions 1) Start long-term save processing When specify Save Folder, Save Condition and Stop Condition, click [Start] button, long-term save processing is started. When an error is found in Save Folder, Save Condition and Stop Condition, an error message is displayed. When Save Folder does not exist, following inquiries is displayed, and it is made automatically. 2) Stop long-term save processing Click [Stop] button, long-term save processing is stopped. Following inquiries are displayed. A processing result is displayed to "Current State". 104

113 8. Log Save Tool 8.4 Decompress log files How to Decompress log files Important: While execute of decompress, OPC server becomes slow and update period of data may become long. About a how to decompress log file with the machine which OPC server is not installed in, please refer to Chapter 9. Click [Decomp...] button. Choose file (extension : cmp) which want to decompress. you can choose several files Click [Open] button. 105

114 8. Log Save Tool Next, select a folder to decompress. When click [OK] button, A log file is decompressed in the folder which specified 106

115 9. Log Decompress Tool 9. Log Decompress Tool 9.1 Outline of Log Decompress Tool Log Decompress Tool uses it with the machine which OPC server is not installed in. And it is a tool to decompress a made file with a Log Save Tool. * Log Decompress Tool added in V Setting-Up Log Decompress Tool This chapter describes installation and uninstall of Log Decompress Tool. Important: Please execute it in a user of Administrator authority. Important : If Microsoft.Net Framework 2.0 isn t installed on your PC or your PC s OS is Windows 8.1, Windows Server 2012 R2, Windows XP or Windows Server 2003, install it according to Installing Microsoft.Net Framework 2.0. Important : When install it in version up of Log Decompress Tool again. uninstall it. 107

116 9. Log Decompress Tool Installing Microsoft.Net Framework 2.0/3.5 When your PC doesn t have Microsoft.Net Framework 2.0 or Microsoft.Net Framework 3.5, you must install it on your PC. On Windows 8.1 When your PC s OS is Windows 8.1, you should install Microsoft.Net Framework 2.0 onto your PC. This can be downloaded via Microsoft WEB page or installed via the installation media When you install this via the installation media, you can make the.net Framework 2.0/3.5 enabled as below. You mount the installation media and enter the following command in the command prompt with the administrator authority. Dism /online /enable-feature /featurename:netfx3 /All /Source:x:\sources\sxs /LimitAccess <cr> (x is the drive name of the installation media.) By right-clicking the left side of the task bar, the menu appears. Select the Command Prompt (Admin). 108

117 9. Log Decompress Tool Figure 9.1 Enable.NET Framework 2.0/3.5 On Windows Server 2012 R2 When your PC s OS is Windows Server 2012 R2, you should install Microsoft.Net Framework 2.0/3.5 into your PC as below. <1> Click Server Manager icon on the task bar. <2> In the Dashboard and choose Add Roles and Features of Manage menu. 109

118 9. Log Decompress Tool <3> In the Before you begin screen, click < Next> >. <4> In Select installation type screen, choose Role-based or feature-based installation. Click < Next> >. <5> In Select destination server screen, choose Select a server from the server pool. Click < Next> >. 110

119 9. Log Decompress Tool <6> In the Select features screen, open.net Framework features, and select.net Framework 3.5 (includes.net 2.0 and 3.0). Click < Next> >. <7> In the Confirm installation selections screen, Click <Install>. <8> It starts to install. 111

120 9. Log Decompress Tool <9> It completes to install. Click <Close>. <10> Close he Server Manager screen, Figure 9.2 Install.NET Framework 2.0/

121 9. Log Decompress Tool On other OS Setup files exist under DotNetFxSetup folder in TC-net OPC Server CD. So you launch them. The following four files must be launched. (1) WindowsInstaller-KB v2-x86.exe : Windows Installer 3.1 Important : When your PC s OS is Windows XP, you must install this. When your PC s OS is Windows Server 2003, you don t need to install this. (2) dotnetfx.exe : Microsoft.NET Framework Version 2.0 Redistributable Package (3) NetFx20SP1_x86.exe : Microsoft.NET Framework Version 2.0 Service Pack 1 (4) NetFx20SP1_ x86ja.exe : Microsoft.NET Framework Version 2.0 Language Service Pack 1 Tip: The agreement statement is shown in Japanese when this is installed. But the content of this is same as one of NetFx20SP1_x86.exe Installing Log Decompress Tool Please do installation of Log Decompress Tool in the next procedure. <1> Launch setup.exe under folder "LogDecompTool" in installation CD Click <Next>. 113

122 9. Log Decompress Tool <2>Input Folder. Normally this folder is C:\Program Files\Toshiba\TC_net OPC Server. If you would like to change it, click <Browse >. In order to use Log Decompress Tool for all logon users, Everyone is selected. If you want to use it only for the current logon user, select Just Me. After setting, click <Next>. <3>Click <Next>. <4>Installation is completed. Click <Close>. Figure 9.3 Install Log Decompress Tool 114

123 9. Log Decompress Tool Uninstalling Log Decompress Tool (1) On Windows XP / On Windows Server 2003 Uninstall the Log Decompress Tool with [Control Panel] [Add or Remove Programs] <1> Select <Add or Remove Programs>. <2>Select TC-net Log Decompress Tool VXX.XX and Click < Remove> button. (VXX.XX is the current version.) It starts to remove program. Figure 9.4 Uninstall Log Decompress Tool (Windows XP/Windows Server 2003) 115

124 9. Log Decompress Tool (2) On Windows 8.1 / Windows 7 / Windows Vista / Windows Server 2012 R2 / Windows Server 2008 R2 / Windows Server 2008 Uninstall the Log Decompress Tool with [Control Panel] [Programs and Features] <1> On Windows 8.1/Windows Server 2012 R2 Open the menu by right-clicking the left side on the task bar, open the Control Panel. Others Open Control Panel from start menu. <2> Open [Control Panel]. Select [Uninstall a program]. When the view is "Classic View" or "Large icons" or "Small icons", select < Programs and Features >. <3>Select TC-net Log Decompress Tool VXX.XX and Click <Uninstall> button. (VXX.XX is the current version.) It starts to remove program. Figure 9.5 Uninstall Log Decompress Tool (Windows 8.1/ Windows 7/Windows Vista/ Windows Server 2012 R2/Windows Server 2008 R2/Windows Server 2008) 116

125 9. Log Decompress Tool 9.3. Launch Log Decompress Tool This paragraph describes how to launch Log Decompress Tool. Select the [Log Save Tool] on the App view on Windows 8.1/Windows Server 2012 R2. Select [Start]-[All Programs]-[ TC-net Opc Server]-[ Log Save Tool] on other OS. When you launch Log Decompress Tool, the main window is displayed On Windows 8.1 / Windows Server 2012 R2 Figure 9.6 Launch Log Decompress Tool (Windows 8.1/Windows Server 2012 R2) On Windows 7 / Windows Vista / Windows Server 2008 R2 / Windows Server 2008 Figure 9.7 Launch Log Decompress Tool (Windows 7/Windows Vista/Windows Server 2008 R2 /Windows Server 2008) 117

126 9. Log Decompress Tool On Windows XP / Windows Server 2003 Figure 9.8 Launch Log Decompress Tool (Windows XP/Windows Server 2003) Figure 9.9 Main screen of Log Decompress Tool 118

127 9. Log Decompress Tool 9.4 Screen / Operation instructions 1) 2) 3) 1) Log Folder Specify folder of compressed log file. Click [Browse...] button and can select a folder. Default folder is " C:\Program Files\Toshiba\TC_net OPC Server\Logs ". 2) [Decomp...] button [Decomp...] button to log file (file which was compressed). Choose file (extension : cmp) which want to decompress. you can choose several files Click [Open] button. Next, select a folder to decompress. 119

128 9. Log Decompress Tool When click [OK] button, A log file is decompressed in the folder which specified. 3) [Close] button [Close] button to close a screen of "Log Decompress Tool". 120