HSP-SP V Release Notes HSP-SP V Release Notes. Page 1 of 6

Transcription

1 HSP-SP V Page 1 of 6

2 Copyright The data in this document may not be altered or amended without special notification from ETAS GmbH. ETAS GmbH undertakes no further obligation in relation to this document. The software described in it can only be used if the customer is in possession of a general license agreement or single license. Using and copying is only allowed in concurrence with the specifications stipulated in the contract. Under no circumstances may any part of this document be copied, reproduced, transmitted, stored in a retrieval system, or translated into another language without the express written permission of ETAS GmbH. Copyright 2018 ETAS GmbH, Stuttgart The names and designations used in this document are trademarks or brands belonging to the respective owners. Page 2 of 6

3 Contents 1 Introduction Definitions and Abbreviations Product Definition Functions at a glance General Description System Prerequisites Changes Configuration Information Released Features New or Enhanced Functions Corrected Errors Known Issues Contact, Support and Problem Reporting... 6 Page 3 of 6

4 1 Introduction 1.1 Definitions and Abbreviations Term/Abbreviation EHI HSP HSP-UT HW KIR SW Definition ETAS Help Desk International Hardware Service Pack HSP-Update Tool Hardware Known Issue Report For severe Problem Reports which occur after a release, ETAS has introduced the Known Issue Report to inform affected customer immediately. The current Known Issues of former versions can be found on the ETAS website: Software 2 Product Definition 2.1 Functions at a glance The Hardware Service Pack is a product for the firmware management on the ETAS hardware. This product consists of two components. HSP Update Tool Service Pack o LABCAR Hardware (LABCAR-FWP) o MCD Hardware (SP) The HSP Update Tool is the user Interface for the firmware update process. This tool enables an easy update of the firmware in the ETAS hardware and gives clear information on the current versions of the firmware contained in the hardware. The Service Pack contains the actual firmware, i. e. the files that will be downloaded to the hardware. These release notes are valid for the HSP MCD Hardware Service Pack. The content of this release notes, i.e. Chapter 3, can also be launched from the HSP Update Tool for each installed Service Pack version. 2.2 General Description System Prerequisites The following minimum system prerequisites have to be met: HSP V has to be installed. See the HSP-UT release notes or Getting Started for information about the HSP installation. Page 4 of 6

5 3 Changes This chapter describes changes with respect to the previous HSP versions and lists the current known issues 3.1 Configuration Information Configuration Version Release Date HSP V Released Features New or Enhanced Functions With this release, the following functionality has been added. This list also shows features of existing previous refreshes of this HSP major version. Description Products Released With Support of new FETK-T1.1B for Infineon AURIX TC3xx microprocessor family: support of TC39x ED (B-Step) Support TC39xED_B and TC38xx XCP Event if CPU type is not matching A2L file Improve Wait/Ready Pattern implementation (MC- /Rp-WaitBit only set if measurement running FETK-T1.1B XETK-S20.0B, XETK- S20.1B, XETK-S30.0C, BR_XETK-S1.0A XETK-S20.0B, XETK- S20.1B, XETK-S30.0C, BR_XETK-S1.0A, Support ExcludeFromTrace Support TC39xED_B and TC38xx (without trace) Support of new probes NTK ZFAS-U3 and BOSCH LSU 5.2 The WriteNewDefaultLines Tool in the HSP Update Tool supports uploading new lines for the probes ZFAS-U3 and LSU5.2. The GE Host connection is now compatible with the Wake Up and Sleep functionality used by the ES8xx devices, i.e. compatible with ES820 use cases ES630.1, ES631.1, ES635.1, ES636.1 ES630.1, ES631.1, ES635.1, ES636.1 ES600.2 Page 5 of 6

6 3.2.2 Corrected Errors The following table contains all errors that have been corrected in this and previous refresh releases. Call ID Description Products Released With XCP Connection interruption in climate test during trace mirror collision test Calibration not working on some PD devices with (invalid calibration handle) Support XCT configured trace rasters with SDISTAB Wrong measurement values after DAP errors FETK-T1.1A XETK-S20.0B, XETK-S20.1B, XETK-S30.0C, BR_XETK- S1.0A, UUID Error with MCE and BR-XETK-S1 ES MAX_DLC_REQUIRED on ES910 together with MCE over XCP on CAN does not work ES910.3 Not possible to initialise Ethercat configuration and XCP on CAN MCE-IlinkRT: ILINK Firmware stops working if I-Link Cable was disconnected during measurement OCD and/or Device Driver are hindering Open FIle Dialog BR_XETK-S3 does not initialize DAP - Interface after LBIST AS951 ES910.3 ES582.1 HSP V Known Issues The following table contains known problems open for this release. Call ID Description Due to a bug in the transfer of trace messages, the FETK may show a high latency. This can lead to a high jitter when using fine grain trace Does not initialize DAP - Interface after LBIST Products FETK-T1.1B FETK-T1.1B, FETK-S1.1B BDF not working if LBIST started via boot mode header 4 Contact, Support and Problem Reporting For details of your local sales office as well as your local technical support team and product hotlines, take a look at the ETAS website: ETAS subsidiaries WWW: ETAS technical support WWW: Page 6 of 6