ES585.1 K-Line Interface Compact. User's Guide

Transcription

1 ES585.1 K-Line Interface Compact User's Guide

2 Copyright The data in this document may not be altered or amended without special notification from ETAS GmbH. ETAS GmbH undertakes no further obligation in relation to this document. The software described in it can only be used if the customer is in possession of a general license agreement or single license. Using and copying is only allowed in concurrence with the specifications stipulated in the contract. Under no circumstances may any part of this document be copied, reproduced, stored in a retrieval system or translated into another language without the express permission of ETAS GmbH. Copyright 2008 ETAS GmbH, Stuttgart The names and designations used in this document are trademarks or brands belonging to the respective owners. Document R1.0.3 EN TTN F 00K K-Line Interface Compact

3 Contents 1 Introduction Functions/Features Applications General Information Requirements Hardware Supported Software Necessary Protocols in the ECU Hardware Description Block Diagram Housing Interfaces and Display Elements PC Printer Interface (Centronics) ECU Interface Analog Output Display Element Power Supply Automatic Power-On Contents 3

4 3 Hardware Configuration and Installation PC Printer Interface (Centronics) ECU Interface (K-Line) Firmware Update Functional Description ECU Interface (K-Line) PC Printer Interface (Centronics) Technical Data Pin Assignment PC Printer Interface (Centronics) ECU Interface (K-Line) General Data Mechanical Data Environmental Conditions Electrical Data Power Supply ECU Interface (K-Line) Printer Interface Analog Output Cable and Accessories Cable Adapter KA Cable K Cable K Cable CBK100-1m Cable Adapter KA Cable Adapter K Ordering Information ES Accessories ETAS Contact Addresses List of Figures Index Contents

5 1 Introduction The ES585.1 K-Line Interface Compact is an ETAS Compact Module for connecting a PC to an ECU. The ES585.1 is connected to the ECU via the K-Line and to the PC via the parallel printer interface. This makes a powerful and universal connection to the PC possible. PC-aided calibration can be carried out at the serial diagnostic interface (K- Line) of an ECU with the intelligent ECU interface ES The functionality of the ES585.1 is basically determined by the operating programs of the PC. This also makes it perfect for all functions to do with operating the diagnostic services of an ECU, such as reading the fault memory or programming ECUs with flash memory. 1.1 Functions/Features 1.2 Applications Powerful interface for K-Line In acc. with ISO for diagnostic testers Transfer rate: up to 250 kbaud Protocols: McMess, KWP2000, Keyword71 Inputs and outputs to the PC galvanically isolated Power is supplied via the connection to the ECU from the onboard power supply with galvanic isolation The ES585.1 can be used in the following calibration tasks, if the ECU provides the functions: Data acquisition Calibrating ECU variables Flash programming of ECUs (K-Line) ECU diagnostics 1.3 General Information Extensive temperature range: -30 C to +70 C (-22 F to +158 F) Compact design Perfect for use in the vehicle Connectors perfect for automotive requirements Integrated in INCA with a user-friendly configuration Introduction 5

6 1.4 Requirements Hardware Firmware update with the service software HSP from the connected PC IBM-compatible PC with printer interface (Centronics) Supported Software The ES585.1 K-Line Interface Compact is supported by the following programs: INCA (basic INCA software with K-Line integration) K-Line-Software ProFWIN (programming of ECUs with Flash-EPROMs) HSP Necessary Protocols in the ECU For the ES585.1 with the K-Line to be able to be used on an ECU, the following protocols have to be implemented in the ECU: Application Measuring/calibrating Diagnostics Programming of ECUs with Flash- EPROM Protocol Calibration protocol McMess or KWP2000 Diagnostic protocol KW71, KWP2000 Diagnostic protocol KWP2000 Tab. 1-1 Protocols in the ECU 6 Introduction

7 2 Hardware Description 2.1 Block Diagram Fig. 2-1 ES585.1 Block Diagram 2.2 Housing A compact, stable metal housing is used for the ES The ES585.1 is specifically designed to be installed in the passenger cell. ES585.1 SN0000 F00K CE Fig. 2-2 ES585.1Housing 2.3 Interfaces and Display Elements PC Printer Interface (Centronics) There is a 25-pin Sub-D connector on the front of the device which makes it possible to connect the device directly to the PC printer interface (Centronics). Hardware Description 7

8 2.3.2 ECU Interface The connecting cable is attached to the ECU on the side of the device. The signals of the K-Line but also the power supply is routed from the ECU to the ES585.1 via this connection Analog Output The K-Line also contains an analog output with which the P-Module can be driven. The P-Module provides a programming voltage for flash EPROMs Display Element There is a display element (LED) on the back of the ES585.1 which indicates the operating states of the ES The following table lists what this LED indicates. LED Status Off On Meaning ES585.1 not operational ES585.1 operational The ES585.1 is operable after an automatic power-on of the ES585.1 (see the section 2.5 on page 8). 2.4 Power Supply The ES585.1 is powered galvanically isolated via KL15 (terminal 15) or UBD (continuous plus) of the ECU. The input voltage range is 6 to 30 Volts. 2.5 Automatic Power-On The ES585.1 is only supplied with voltage when the ES585.1 is connected correctly to the Centronics interface, the PC is switched on and the supply voltage is connected via KL15 or UBatt. 8 Hardware Description

9 3 Hardware Configuration and Installation This chapter describes the steps necessary to put the ES585.1 into operation. ES585.1 K-Line Interface ECU SN0000 F00K CE Printer Interface INCA-PC Fig. 3-1 ES585.1 Connection 3.1 PC Printer Interface (Centronics) The ES585.1 is connected directly to the printer interface (Centronics) of the PC. This makes a powerful and universal connection to the PC possible. 3.2 ECU Interface (K-Line) The ES585.1 is connected to the ECU directly via the 14-pin round connector. There are also extension cables available in various lengths as well as cable adapters (see chapter 6 on page 17). The connection must not be longer than 10 m. 3.3 Firmware Update The firmware of the ES585.1 can be updated by the user from the connected PC using a service software. The program HSP is required for the firmware update of the ES Hardware Configuration and Installation 9

10 10 Hardware Configuration and Installation

11 4 Functional Description The ES585.1 can be used for PC-aided calibration at the serial diagnostic interface of an ECU. The ES585.1 is an intelligent interface which makes it possible to connect ECUs and a PC. The ES585.1 exchanges data automatically with the ECU thus particularly relieving the PC of time-critical protocol tasks ensuring the high transfer rates used by ECUs in calibration. 4.1 ECU Interface (K-Line) The K-Line (serial ECU diagnostic interface) is the interface to the ECU. The interface connection of the ES585.1 adheres to the ISO standard for diagnostic testers (without L-Line) with a maximum transfer rate of 250 kbaud. Communication on the interface takes place with the calibration and diagnostic protocols McMess, Keyword71 and KWP2000. The baud rate and the system frequency are set by a program on the PC. The functionality of the K-Line interface of the ES585.1 is basically determined by the operating programs of the PC. 4.2 PC Printer Interface (Centronics) The physical transfer of the data takes place at the PC printer interface (Centronics) from the PC to the ES585.1 in Byte mode via the data lines of the Centronics interface and from the ES585.1 to the PC in Nibble mode via several control lines of the Centronics interface. Communication on the interface takes place in accordance with the INCA protocol. Functional Description 11

12 12 Functional Description

13 5 Technical Data 5.1 Pin Assignment This section describes the pin assignment of the ES PC Printer Interface (Centronics) Fig. 5-1 ES585.1 Printer Interface The Centronics interface of the ES585.1 can work with every standard printer interface of a PC ECU Interface (K-Line) Fig. 5-2 ES585.1 Interface to the ECU Pin Signal Pin Signal A Term. 15 H V pp B SG GND I reserved C SG GND K reserved D K-Line L reserved E reserved M reserved F reserved N reserved G reserved O UBD Tab. 5-1 Assignment of the Interface to the ECU Technical Data 13

14 5.2 General Data Mechanical Data The dimensions listed in the table refer to the housing of the basic ES585.1 device without cables. Height Width Depth Weight 17 mm (0.7 in.) 59 mm (2.3 in.) 71 mm (2.8 in.) 260 g Environmental Conditions Ambient temperature during operation -30 C to +70 C (-22 F to +158 F) 5.3 Electrical Data Power Supply Power supply Input voltage Power consumption (typ.) Power consumption (standby) No external power supply; supply via K-Line socket of the ECU 6 V to 30 V 1 W at 13.5 V 30 mw at 13.5 V ECU Interface (K-Line) K-Line interface (ISO ) Design Cable length Protocols Max. 250 kbaud, set using software Galvanically isolated 2.5 m (8.2 ft), can be extended to max. 10 m (32.8 ft) McMess, KWP2000, KW71 14 Technical Data

15 5.3.3 Printer Interface Printer interface Centronics Analog Output Output voltage Quantization Resolution 0 V to V Δ=1.0 mv 12 Bit Technical Data 15

16 16 Technical Data

17 6 Cable and Accessories 6.1 Cable Adapter KA45 Fig. 6-1 Cable Adapter KA45 Signal Description Plug Color Labeling UBD Power supply (plus; KL.15) Red 6-30V= Ground Ground (power supply, signal) Black GND K K-Line Yellow K-Line L L-Line Green L-Line V PP Analog output (programming voltage for Flash-EPROMs) Blue Reserved 1) ES585.1: not used Tab. 6-1 Cable Adapter KA45: Assignment of the Plugs Order Name Length Order Number Cable Adapter KA m (0.6 ft) F 00K Cable and Accessories 17

18 6.2 Cable K78 Fig. 6-2 K-Line Interface Cable K78 Order Name Length Order Number K-Line Interface Cable K78 3 m (9.8 ft) F 00K Cable K96 Fig. 6-3 K-Line Interface Cable K96 Order Name Length Order Number K-Line Interface Cable K96 8 m (26.3 ft) F 00K Cable CBK100-1m5 Fig. 6-4 K-Line Interface Cable CBK100-1m5 Order Name Length Order Number K-Line Interface Cable CBK100-1m5 1.5 m (4.9 ft) F 00K Cable and Accessories

19 6.5 Cable Adapter KA18 Fig. 6-5 Cable Adapter KA18 Order Name Length Order Number Cable Adapter for K-Line Extension 0.2 m (0.6 ft) Y 261 A KA Cable Adapter K72 Fig. 6-6 Cable Adapter K72 Order Name Length Order Number Cable Adapter K72 3 m (9.8 ft) F 00K Cable and Accessories 19

20 20 Cable and Accessories

21 7 Ordering Information 7.1 ES585.1 Order Name Short Name Order Number ES585.1 including ES585.1 F 00K Cable Adapter KA Accessories Order Name Short Name Order Number Cable Adapter KA45 KA45 F 00K Cable Adapter K72 K72 F 00K K-Line Interface Cable KA78 KA78 F 00K K-Line Interface Cable KA96 KA96 F 00K K-Line Interface Cable CBK100-1m5 CBK100-1m5 F 00K Cable Adapter for K-Line Extension KA18 KA18 Y 261 A Ordering Information 21

22 22 Ordering Information

23 8 ETAS Contact Addresses ETAS HQ ETAS GmbH Borsigstraße 14 Phone: Stuttgart Fax: Germany WWW: North America ETAS Inc Miller Road Phone: ETAS INC Ann Arbor, MI Fax: USA WWW: Japan ETAS K.K. Queen's Tower C-17F Phone: , Minatomirai, Nishi-ku Fax: Yokohama Japan WWW: Great Britain ETAS Ltd. Studio 3, Waterside Court Phone: Third Avenue, Centrum 100 Fax: Burton-upon-Trent Staffordshire DE14 2WQ WWW: Great Britain ETAS Contact Addresses 23

24 France ETAS S.A.S. 1, place des Etats-Unis Phone: SILIC 307 Fax: Rungis Cedex sales@etas.fr France WWW: Korea ETAS Korea Co. Ltd. 4F, 705 Bldg Phone: Yangjae-dong, Seocho-gu Fax: Seoul sales@etas.co.kr Korea China ETAS (Shanghai) Co., Ltd Bank of China Tower Phone: Yincheng Road Central Fax: Shanghai sales.cn@etasgroup.com P.R. China WWW: India ETAS Automotive India Pvt. Ltd. No. 690, Gold Hill Square Phone: F Hosur Road, Bommanahalli Fax: Bangalore sales.in@etasgroup.com India WWW: 24 ETAS Contact Addresses

25 List of Figures Fig. 2-1 ES585.1 Block Diagram... 7 Fig. 2-2 ES585.1Housing... 7 Fig. 3-1 ES585.1 Connection... 9 Fig. 5-1 ES585.1 Printer Interface Fig. 5-2 ES585.1 Interface to the ECU Fig. 6-1 Cable Adapter KA Fig. 6-2 K-Line Interface Cable K Fig. 6-3 K-Line Interface Cable K Fig. 6-4 K-Line Interface Cable CBK100-1m Fig. 6-5 Cable Adapter KA Fig. 6-6 Cable Adapter K List of Figures 25

26 26 List of Figures

27 Index A Accessories 17 Accessories, ordering information 21 Analog output 8, 15 Applications 5 B Baud rate 11 Block diagram 7 Byte mode 11 C Cable adapter 9 Cable Adapter KA18 19 Cable Adapter KA45 17 Cable Adapter KA72 19 Cable CBK100-1m5 18 Cable K78 18 Cable K96 18 Cables 17 D Data electrical 14 general 14 mechanical 14 Diagnostic interface 5 Display element 8 E ECU 5 protocols in the 6 Electrical data 14 Environmental conditions 14 ES585.1, ordering information 21 ETAS Contact Addresses 23 Extension cable 9 F Fault memory 5 Firmware update 6, 9 Flash memory 5 Functional description 11 Functions 5 Index 27

28 G General data 14 General information 5 H Hardware 6 Hardware description 7 Housing 7 HSP 6, 9 S Service software 6 Supported software 6 System frequency 11 T Technical data 13 Transfer rate 5 I INCA protocol 11 ISO , 11 K K-Line 5 L LED 8 M Mechanical Data 14 N Nibble mode 11 O Ordering information 21 accessories 21 ES P Pin assignment 13 P-Module 8 Power supply 8, 14 Programming voltage 8 Protocols 5 Protocols in the ECU 6 Protocols to be implemented 6 R Readiness for operation 8 Requirements 6 28 Index