Features Freely programmable on and off switching speed Operation via included software (RS485 interface) Additional incremental signals (HTL/TTL) EURO-flange B10 / shaft ø11 mm DSL.R: 3 outputs speed controlled (independent transistor outputs) DSL.E: 2 outputs speed controlled and 1 control output Optional Relay module DS 93 R (DSL.R version only) Technical data - electrical ratings Consumption w/o load 200 ma Resolution (steps/turn) 512...2500 Phase shift 90 ±20 Interface RS485 Scan ratio 40...60 % Switching accuracy Switching delay time ±2 % (Digit) 40 ms Reference signal Zero pulse, width 90 Outputs Output frequency Sensing method,, + inverted HTL + TTL 120 khz Optical Interference immunity DIN EN 61000-6-2 Emitted interference DIN EN 61000-6-4.E Voltage supply Switching outputs Output switching capacity.r Voltage supply Switching outputs Output switching capacity 9... 30 VDC 2 outputs, speed control 1 control output 5...230 VAC/VDC 5...250 ma 15...30 VDC 3 outputs, speed control 12 V High: ns 0 V Low: n ns Technical data - mechanical design Dimensions (flange) Shaft Flange ø120 mm ø11 mm Protection DIN EN 60529 IP 66 Speed (n) Range of switching speed (ns) Operating torque Rotor moment of inertia Shaft loading Materials EURO flange B10 6000 rpm Resolution = 512: ±16...6000 rpm Resolution = 1024: ±8...6000 rpm Resolution = 2048: ±4...3500 rpm Resolution = 2500: ±3...2900 rpm 2 Ncm 290 gcm² 300 N axial 450 N radial Operating temperature -30...+85 C Housing: aluminium die-cast Shaft: stainless steel Resistance DIN EN 60068-2-6 Vibration 20 g, 10-2000 Hz DIN EN 60068-2-27 Shock 200 g, 6 ms Explosion protection Weight approx. Connection II 3G Ex na T4 X (gas) II 3D Ex td IP66 A22 T135 C X (dust) 3.3 kg Terminal box
Part number POG 10 DN + DSL.E POG 10 DN + DSL.R I R Incremental output Output circuit HTL with Output circuit TTL with I R Incremental output Output circuit HTL with Output circuit TTL with See part number (pulses) DN,, See part number (pulses) DN,, Part number (pulses) 512 1024 2048 2500 Accessories Adapter USB RS485 Connectors and cables HEK 8 Sensor cable for encoders Mounting accessories K 35 Spring disk coupling for shaft ø6...12 mm K 50 Spring disk coupling for shaft ø11...16 mm K 60 Spring disk coupling for shaft ø11...22 mm Diagnostic accessories HENQ 1100 Analyzer for encoders Relay module for.r DS 93 R Relay modul
at positive rotating direction Terminal assignment View A - Connecting terminal in terminal box zero pulse zero pulse 90 (GND) +UB Terminal significance Speed switch version DSL.R R1* Transistor switching output 1, R2* Transistor switching output 2, R3* Transistor switching output 3, GND* Ground connection Interface for PC or Laptop (adapter required). Operation of the DSL via the included software. * Connection to relay module, for example DS 93 R (accessory) Speed switch version DSL.E R1 (A+B) Electronic relay output 1, 5... 230 V AC/DC R2 (A+B) Electronic relay output 2, 5... 230 V AC/DC C1 (A+B) Electronic relay output as a control output, 5... 250 ma Interface for PC or Laptop (adapter required). Operation of the DSL via the included software. View B - Connecting terminal speed switch Version DSL.R R1 R2 R3 GND View B - Connecting terminal speed switch Version DSL.E R1 R2 C1
Block circuit diagram Version with DSL.E C1-A 9...30 VDC Control C1-B R1-A R1-B Encoder DSL.E R2-A R2-B A, B RS485 (PC/Laptop) Version with DSL.R 15...30 VDC High = 12 V Low = 0 V R1 12 VDC (High) Manner of output circuit Encoder DSL.R R2 R3 A, B RS485 (PC/Laptop) R1, R2, R3 (Low) -n +n -ns (off) -ns (on) 0 +ns (on) +ns (off) n = speed ns (on) = adjusted switching on speed ns (off) = adjusted switching off speed
Dimensions Positive rotating direction A B M20x1.5 M20x1.5 HM04M26794