*24908394* 24908394 Bseplte Conversion Kit QEL 33A/35A, 98/99 Series Instlltion Instructions 1. This kit converts ll 33/35A nd 98/99 series EL devices nd fire devices uilt prior to Oct. 2014 to quiet electric ltch (QEL) retrction devices. 2. Instll ccording to instructions or device will not function nd pnic or fire lel will e void. 3. The QEL wiring must e ttched to the fire lrm system if instlled on fire exit hrdwre. Prts Tools Required ⁵ ₈" Drill Bit QEL Bseplte w/o Dogging (replces EL Bseplte nd Fire Bseplte) QEL Bseplte with Dogging (replces EL-HD Bseplte) WARNING If existing exit device is fire rted, do not instll HD-QEL (hex dogging) seplte. Doing so will void fire rting.
1 Disconnect Power To void risk of shock, disconnect AC power from power supply efore proceeding with this conversion. If using Bttery Bckup option, unplug ll four wires from ttery terminls. 4 Remove Old Bseplte Assemly 4 Remove Mechnism Cse 33/35 2 Detch Verticl Rods if present Refer to device instructions s needed. 3 Remove Exit Device from Door Keep ll prts d c! Device nd trim must e held securely while screws re eing removed, to prevent dropping to the floor OR 98/99 c Unplug cle, 4 Remove Pushpd From Bseplte. d Keep pushr 2
4 Remove Old Bseplte Assemly (continued) 4c Discrd retining ring nd pin 5 Instll New QEL Bseplte Assemly 5 Attch existing center cse to new seplte using two screws Discrd retining ring nd pin 4d Discrd old seplte 5 Instll new pin nd retining ring Discrd old seplte Keep center cse Ensure tht retining ring is in grove. 3
5 Instll New QEL Assemly (continued) 5c Instll pushpd Ensure plstic clips re ttched 7 Prepre dogging cover for HD dogging key (if ppliclle nd only on pnic devices). 7 Locte nd drill hole 1/4 Center of Cover Deurr edge of hole 1 1/2 7 Instll dogging cover 6 Instll mechnism cse NOTE: During step A, verify tht plstic pushr clips re ligned properly inside cse. c 33/35 8 Drill Wire Access Hole (if required) ⁵ ₁₆" d OR 98/99 Drill ⁵ ₈" di. ccess hole through device side of door. 4
9 Attch Exit Device to Door d For more detiled instlltion instructions for specific Exit Devices, visit the Support re of the Allegion wesite t www.llegion.com/us 10 Confirm Equipment Comptiility The QEL is comptile with the following equipment (refer to individul instructions s needed): PS900-Series power supplies - PS902, PS904, PS906, PS914 900-Series option ords - 900-2RS, 900-4R, 900-4RL, 900-2Q PS873 power supply plus 871-2, 871-2Q, 873-4TD/AO option ords 11 Route Two Wires from QEL Exit Device to Power Supply QEL Electricl Lod Voltge: 24 VDC Current: 1.0 A inrush (0.5 sec) 0.14 A holding PS900-Series power supply with 900-Series option ord(s) instlled QEL device used with EPT, Door Loop, or Electric Hinge/Pivot Distnce (one wy) Wire Guge 200 18AWG 320 16AWG 500 14AWG 800 12AWG EPT shown. A door loop or electric hinge/pivot my lso e used. QEL Exit Device Note: Power wires to QEL re not polrized. 5
12 Instll 900-2Rs, 4Rl, or 4R Option Bord(s) into Power Supply Review Aville 900 series Option Bord Mounting Loctions (Gry) Plug Option Bord Cle into ny Aville Option Connector Option 1 PS902 1 Bord PS902 1 Option 1 Option 2 PS904, 914 2 Bords 1 Option 1 Option 2 Option 3 PS906 3 Bords PS904 PS914 1 2 c Secure Bord(s) with Screws Notes: 1. 24VDC output setting required when QEL device connected 2. If instlling ord in loction 2 or 3, rotte ord 180 PS906 1 2 3. The QEL is comptile with n existing 900-2Q ord if currently instlled. 4. Ltcholt retrction of (2) sequenced QEL s requires more thn 1 second to complete. 3 5. When powering multiple components, verify tht the mperge requirements of ll components comined does not exceed the power supply output rting. 13 Connect Input nd Output Wires to Option Bord (2RS Shown) Individul Mode - Typicl Wiring Sequentil Mode - Typicl Wiring PS900 120/240 VAC (PS900 Series 50/60Hz Series only) 2RS Input I1 will ctivte oth outputs SC I1 01 I2 02 GND PS900 Series 120/240 VAC 50/60Hz 2RS SC I1 01 I2 02 GND Access Control for Device 2 Input I1 will ctivte output 1 Input I2 will ctivte output 2 EPT-2/10 QEL Device 2 Note: Fil secure output only llowed if pproved y Authority Hving Jurisdiction Access Control for Devices 1 & 2 EPT-2/10 EPT-2/10 QEL Device 1 QEL Device 2 Access Control for Device 1 EPT-2/10 QEL Device 1 6
14 Check Opertion A. Activte ech input nd verify ll QEL devices operte properly. B. If ny device does not operte properly, see step 15 for trouleshooting. 15 If Necessry, Trouleshoot Opertion (LED is only visile with the mechnism cover removed) Power t the QEL 24VDC 24VDC low 29VDC or greter 13VDC or lower 0VDC 0VDC QEL Response LED - Solid green Ltcholt - retrcted LED - Solid red fter ltcholt ttempts to retrct multiple times LED - Flshing green/red Ltcholt - not retrcted LED - Flshing green Ltcholt - retrcted LED- Flshing red Ltcholt - will not retrct LED - off Ltcholt - not retrcted LED - off Ltcholt - retrcted Condition/Solution Opertion norml, ltch retrcted immeditely Ltcholt cnnot fully retrct mechniclly Verify mechnicl djustment (on verticl rod or mortise lock devices if used). Remove nd repply input voltge to reset this condition.* See Check Mechnicl Opertion on pge 8 s needed.** Excessive tmper (while power pplied, the pushpd ws pulled out t lest 3 time) Wit 15 seconds nd ltcholt will retrct gin OR remove nd repply power to cler condition Voltge low during ltcholt retrction (ltcholt retrcts t reduced force) Wire length is too long, wire guge is too smll or power supply hs poor regultion Input voltge is too high for proper opertion Wrong power supply, power supply defective. Input voltge is too low for proper opertion Wrong power supply, power supply defective or not set to the proper output voltge. To set, remove AC power from power supply, chnge power supply setting from 12 to 24VDC, then repply AC power nd verify proper opertion. No input voltge Prolem with the power supply, control switch or wiring No input voltge Mechnicl dogging is engged *For informtion out djusting exit devices, you cn find their instlltion instructions in the support re t www.llegion.com/us or cll Technicl Services t 1-877-671-7011 LED on Device 7
16 Check Mechnicl Opertion 33A/3527A 98/9927 98/9947WDC 33A/3547A 98/9947 98/9957 98/9975 33/3549A 98/9949 33/3550A-WDC 98/9949WDC 98/9950WDC 1. Mke sure device is not dogged for SD-QEL / HD-QEL. 2. Depress pushr nd mke sure ltch olt retrcts nd extends fully (see Figure 1). 3. If ltch olt does not retrct or extend fully, djustments my e required per the device instlltion instructions. 33A/3527A, 98/9927, 98/9957 Ltch olt dedlocked (will not push in) with door closed Ltch olt stys retrcted 33A/3547A, 98/9947, 98/9947WDC Ltch olt dedlocked (will not push in) ⁵ ₈" ³ ₁₆" Relese trigger extended with door open Flush within ¹ ₁₆" 1. Mke sure device is not dogged for SD-QEL/HD-QEL. 2. Depress pushr. Door should egin to open with pushr depressed hlfwy. 3. Close door. Top ltch should e secure. If two point ltch, ottom ltch should e secure s well. 4. If device does not function s descried in steps 2 nd 3, djustments my e required per the device instlltion instructions. Any HD Device 1. Fully depress pushr. 2. Insert hex dogging key nd turn clockwise. 3. Relese pushr nd verify ltcholt remins retrcted. 4. Fully depress pushr. 5. Insert hex dogging key nd turn counter clockwise. 6. Relese pushr nd verify ltcholt extends fully. Ltch olt extended 98/9975 Ltch olt extended ³ ₄" Ltch olt retrcted Ltch olt retrcted Flush within ¹ ₁₆" Figure 1 Customer Service 1-877-671-7011 www.llegion.com/us Allegion 2016 Printed in U.S.A. 24908394 Rev. 01/16-c