322011 LE06448AA01CN-13W17 Description 12 1 11 10 9 23 13 14 2 22 15 16 8 21 17 7 3 20 6 4 5 19 18 1. Compensation Lamp 10. Lens of the access control (Optional) 18. Targe BUS use CAT5 table connect to targe 2. Key used to send the call to the selected resident 3. Door lock release key 4. Photosensitive lamp 5 Microphone 11. 12. 13. 14. Loudspeaker Camera: pick up the image PP NN TS : configurator ISP: entrance panel software upgrade connector 19. 20. SYSTEM BUS use CAT5 cable connect to system 6P connector +12V/GND: supply power to A/C module UNLOCK: unlock signal output by A/C module DAS: connector of electronical lock status signal LOCK-/LOCK+: connect electronical lock. 6. Management center pushbutton: call the management center 15. SPK: adjust loudspeaker volume 21. SPK-OUT/GND/GND/SPK-OUT: connect entrance panel loudspeaker 7. Delete key 16. MIC: adjust microphone volume 22. V-GAIN: video gain setting 8. Number pushbutton 17. VIDEO-IN/GND/NC/+12V/LED-: connect entrance panel camera and compensation Lamp 23. RESET: for password reset 9. Resident search keys
Technical data - standby current 25 ma; voltage 30 Vdc working current 245mA; voltage 30 Vdc 125 mm 44,5 mm - setting entrance panel address by configuration resistors 325 mm P P N N T S P: Entrance panel address N: Call number (Not used) T: Door lock time delay(not used) S: Type of call signal(not used) Installation on the wall Installation on the door Note - Embedded box for installation on door should be bought separately. - This installation instruction is just for entry panel. For embedded box installation, please refer to embedded box installation instruction. 2
Function setting 1.Configuration using the keypad 1.1Access to the configuration menu Press and hold down keys for more than 10 seconds Confirm OK 1.3.3 Home page The home page can be used to enter a customised welcome message, or any other message; the message can use a maximum of three rows of text of 15 characters (Template); to switch from upper case to lower case and vice versa use the arrow keys. The length of time the - message is displayed on the screen (5, 10, or 15 sec.) (Timeout). Entering the text, Press OK Enter the access code (default 1234) If the correct code has been entered, direct access to the configuration menu will be granted Select the row text and confirm OK where to enter the new text, or change the existing To exit the configuration menu, or to return to the previous menu, select EXIT and press OK Press OK to select the text field 1.2 If the password is forgotten If the password has been forgotten it s possible to reset it in this way: Press the RESET key which on the back of the device for about 6s. password recover the default 1234. 1.3 Panel settings Enter the text using the alphanumeric keypad, in the same way as you would write an SMS message on your mobile phone Confirm OK The new message will appear continuously on the home page for the period set a Timeout 1.3.4Restore default settings Select the menu, Confirm OK Select the function, Press OK 1.3.1Device settings The DEVICE SETTINGS submenu can be used to set the following functions: Brightness Display brightness adjustment Contrast Contrast adjustment(not used) Exit return to the previous menu 1.3.2 Password setup Press OK The settings of the entrance panel revert to the factory settings. This function does not delete the data contained in the residents address book. 1.4 Address book This menu can be used to enter residents data, including call codes and door lock release codes, as well as for performing any other functions described in the following paragraphs. To change the access password: Press OK,Enter the new password 6789 1.4.1 Calling mode - List of names This setting determines how the names of the residents are displayed; if enabled, the display will show the following message: 3
To search the desired name use the indicated key, or enter the surname using the alphanumeric keypad. NO = The name and the surname of the resident are hidden, the call is possible by entering the ID number. Apart address: Enter the handset SCS address Call code: Numerical call code Lock code: Door lock release numerical code 1.4.7 Delete contact This function gives the possibility of deleting the contact selected 1.4.2 Calling mode - Type of code Enter the type of code to use when calling the residents Select the contact to change,press OK Apart address: SCS address of the handset Call code : Numerical code assigned to the resident The request to confirm the elimination of the contact appears, press OK 1.4.3Calling mode Recall 1.4.8Delete address book This function gives the possibility of deleting all the contacts of the entrance panel address book, press OK. When this function is enabled, the entrance panel will automatically repeat the call every 10 seconds for up to 4 times. 1.4.4 Contact setting The call codes and the door lock release codes can be set with a length of 1 to 8 digits for the Call code and 4 to 9 digits for the Lock code. 1.5Phonic module settings The configurations of this menu are only possible if the phonic (speaker) module is not configured physically Call code digits: Length of the codes for calling residents (default 4 digits) Lock code digits: Length of the door lock release codes (default 9 digits) 1.4.5 Modify contact This function gives the possibility of changing the contact selected P - panel number: Entrance panel SCS address T - Lock time: Door lock time delay (Not used) Switchboard: SCS address of the switchboard Signal type of lock: ON=open NC=close Dismantle alarm : ON=enable OFF=unable 1.6 FW versions This menu shows the versions of the firmware installed on the device. Select the contact to change, Confirm OK 1.4.6 New contact This function can be used to enter new residents in the address book 2 Using the entrance panel 2.1Calling residents Residents may be called in three different ways: 2.1.1Searching using the arrow keys Press one of the arrow keys to access the address book For each resident it will be possible to set the following data: ID number: Identification number; the entrance panel assigns a progressive num ber to each resident. This function gives the possibility of changing this ID with a 4 digits number defined by the installer. Surname (Text 1*): Surname of resident Name (Text 2*): Name of the resident Public: YES = The name and the surname of the resident appear on the display during the selection for call Use the arrow keys to scroll through the names until the name of the desired resident appears; for fast scrolling press and hold the key, Press to send the call OK. 4
2.1.2Tramite ricerca per cognomen Press one of the arrow keys to access the address book Use the keypad in the same way as a mobile phone keypad to enter the surname, or even just the initial of the contact to call Press to send the call OK 2.1.3Using the numerical code If the resident s call code is known, simply enter it on the keypad Enter the resident code Press to send the call OK 2.2 Call to the switchboard To call the switchboard directly press this key 2.3 Door lock release using a numerical code The procedure to follow for releasing the door lock associated to the entrance panel using the lock code changes depending on the length of the codes assigned to the residents, which can be up to the maximum length set. Press the key If the length of the code is the same as the maximum length set the door lock is released 5