velocity lite 08 velocity features and benefits: dimensions: additional information:

Transcription

1 velocity lite 08 VL08 Attractive and versatile a lightweight, portable 10 x20 structure is complemented with dyesublimated fabric graphics and rigid accent graphics to emphasize your facetoface marketing message. features and benefits: Custom appearance Easy to assemble Combination of rigid and fabric graphics Aluminum construction: vertical extrusions square 50mm x 50mm dimensions: Hardware Assembled unit: (w) x 94.5 (h) x (d) approx mm(w) x 2400mm(h) x 898.7mm(d) Table: 21.2 (w) x 40.5 (h) x 19.7 (d) approx mm(w) x mm(h) x 500.4mm(d) Shipping Shipping dimensions ships in 4 cases Each WMC12x6 case: 52 (l) x 30 (w) x 15 (h) mm(l) x 762mm(w) x 381mm(h) Installation tool included Kit includes one frame, two tables, four rigid graphic accents, eight fabric graphic panels, eight 50 watt spotlights, two literature holders, and four WMC12x6 molded cases Lifetime hardware warranty against manufacturer defects Graphic Panel B,D,E,G: Total visible area: w x 98.5 h mm(w) x mm(h) Panel A,C,F,H: Total visible area: w x 94.5 h 300mm(w) x mm(h) Wings: Total visible area: 11.5 w x h 292.1mm(w) x mm(h) Refer to related graphic template for more information. Approximate shipping weight (entire kit): 252 lbs/114 kg additional information: Graphic materials: Dyesublimated fabric & UV prints on 6mm sintra Table holds max weight 25 lbs/11.3 kg Tabletop color options: Wings can be upgraded to frosted plex Lights included: LV1 50 watt, low voltage spotlight, curved arm, silver finish, 19.5 from end to end silver black mahogany natural velocity 2013 Nimlok Display and Exhibit Solutions Worldwide For questions contact your local Nimlok distributor

2 Parts Included Qty Part code 0 PH300SS VE14 x8 PH1200SS 8 PM2S1200AA VE45 x9 PHYSC1 Panel A Panel B Panel C Panel D Panel E Panel F Panel G Panel H Wing x4 Standoff 2 CKSO Brochure Holder x2 ABH01 VWSCT01 x2 VWSCT01 VL02 x2 VLG02 Light x8 LV1CLP Tool Kit VTK01 Step stool STEP STOOL Steamer FABRIC STEAMER ES SCALE REF = 5ft Part Label 1.

3 Step 1. Push rubber gasket in bottom of graphics into VE14/ horizontal bar channels. See detail below. PANEL H PANEL E PANEL F PANEL G PANEL C PANEL D PANEL A PANEL B BOTTOM CHANNEL VE14 VE14 VE14 VE14 PULL TABS Fabric graphic is installed by pressing t into TOP and BOTTOM channel. To pull the graphic out of the channels, use TABS on the back side. 2.

4 Step 2. Attach uprights into the VE14/ horizontals using Thandle described in the detail below. Then slide internal connectors into the uprights. Take care to turn lock only half a turn. EXTRUSION WITH LOCK POST WITH STOP 1 2 T TOP EXTRUSION ITH LOCK T HANDLE LOCK T BOTTOM STOP STOP LOCK HORIZONTAL EXTRUSION BY USING T HANDLE TOOL 3.

5 Step 3. Slide upper s over the internal connectors to complete uprights. 4.

6 Step 4. Assure rubber gaskets around graphics are completley pushed into all surrounding pieces. Attach VE14/ horizontals to uprights using Thandle described in the detail below. VE14 VE14 VE14 VE14 TOP CHANNEL EXTRUSION WITH LOCK EXTRUSION ITH LOCK T HANDLE LOCK PULL TABS LOCK HORIZONTAL EXTRUSION BY USING T HANDLE TOOL Fabric graphic is installed by pressing into TOP and BOTTOM channel. To pull the graphic out of the channels, use TABS on the back side. 5.

7 Step 5. To connect wings, attach two standoffs per wing to the designated uprights at designated heights. Secure wings using attachment detail below. To connect the brochure holders, attach two standoffs per brochure holder to the designated s at desired height. Apply brochure holder using attachment detail below. GRAPHIC WINGK GRAPHIC WING I BROCHURE HOLDER BROCHURE HOLDER GRAPHIC WINGL GRAPHIC WING STANDOFF Top BROCHURE HOLDER Channel of extrusion NT Toggle STANDOFF Top STANDOFF DETAIL Graphic Channel of extrusion NT Toggle STANDOFF STANDOFF Barrel STANDOFF Barrel Screw the NT toggle into the base of the STANDOFFbarrel and then insert the NT toggle into the channel of the extrusion and twist to tighten into place. Next, place the top of the STANDOFF through the hole in the BROCHURE HOLDER and then screw on thestandoff top to secure the graphic in place. Screw the NT toggle into the base of the STANDOFF barrel and then insert the NT toggle into the channel of the extrusion and twist to tighten into place. Next, place the top of the STANDOFF through the hole in the graphic and then screw on the STANFOFF top to secure the graphic in place. 6.

8 Step 6. Attach to back side of table leg as seen in locking detail below. Attach with leg to designated VE36 upright. Attach VWSCT01 tabletop to table legs using connector detail below. VWSCT01 VWSCT01 VL02 EXTRUSION TO LEG VL02 LEG 5mm Hex key Tool Place LEG and lock horizontal extrusions by using 5mm hex key tool. 7.

9 Step 7. Slide eight lights onto clamps and place over VE15 as shown in detail below. W/ CLAMP LV1 Light CLAMP 1 Slide light clip onto the. 2Then slide the into the channel at an angle and then gently lower down. 8.

10 check out these related products: velocity lite 01 velocity lite 05 velocity lite 02 velocity lite 06 velocity lite 03 velocity lite 07 Redesign of this exhibit without approval by Nimlok may result in dangerous and unsafe structures. Nimlok disclaims any responsibility for redesigned exhibits it does not approve in writing. Parts and components such as panels and extrusions are manufactured to metric sizing. We continue to improve and modify our product range and reserve the right to vary the specifications without prior notice. All dimensions and weights quoted are approximate and we accept no responsibility for variance. E&OE. See Graphic Templates for graphic bleed specifications. velocity lite 04 velocity lite 08