INSTALLATION AND PROGRAMMING MANUAL MTMKB FB00748-EN

Transcription

1 INSTLLTION ND RMMING MNUL MTMKB FB00748-EN

2 General precautions IMPORTNT! Important safety instructions: RED CREFULLY! Installation, programming, commissioning and maintenance must only be carried out by expert qualified technicians in full compliance with the regulations in force. Wear anti-static shoes and clothing if working on the electronic circuit board. Keep this precaution information. Disconnect the power supply during any cleaning or maintenance work. The product must only be used for the purpose for which it was expressly designed. ny other use is to be considered dangerous. The manufacturer declines all liability for any damage as a result of improper, incorrect or unreasonable use. DESCRIPTION Keypad module connectible on BUS. ssembly and removal of the module must take place with no power to the entry panel. ❶ Sockets for the connector to connect additional modules. ❶ NUMBERING OF CLL KEYS Organisation of call codes where there are call keys Technical data Type MTMKB Power supply (V DC) 10.7 to 18 MX consumption (m) 55 MIN consumption (m) 5 Storage temperature ( C) -25 to +70 Operating temperature ( C) -25 to +55 Protection rating (IP) 54 In manual programming the call keys are arranged as in the diagram for a maximum of 98 keys. In this way, for example, pressing key 6 corresponds to entering number 6 on the MTMKB keypad followed by key. Page 2 - Manual FB00748-EN - vers. 1-04/2017- Came S.p.. - The contents of this manual may be changed, at any time, and without notice.

3 RMMING CLL CODES ND DOOR-RELESE CODES This programming is available only with audio modules MTM/01 and video modules MTMV/01. Call programming associates a call code with each internal receiver. Programming the door-release codes associates number codes with the relays present on audio module MTM/01 or video module MTMV/01. The control is local and where there is more than one audio module MTM/01 and video module MTMV/01 carry out the door-release programming on each entry panel. Going into Programming V/01 MTM/01 MTMV/01 With V/01 Press the key until the LED lights up. >3 s B >3 s <6 s With MTM/01-MTMV/01 without V/01 Press the key for at least 3 seconds and release it within 6 seconds B. Page 3 - Manual FB00748-EN - vers. 1-04/2017- Came S.p.. - The contents of this manual may be changed, at any time, and without notice. C Programming the call codes D E The LED will flash to signal entry into programming C. Press the door-release and UX2 keys and enter the group call code (from 1 to 98) followed by key : The call code is associated with the internal receiver D and the call key chosen E. Continue, repeating the same operations for all the other internal receivers. The operation can only be carried out from an entry panel with the LED off. To change the entry panel from which to carry out call programming, you must press key 1 followed by key.

4 Programming door-release codes and relay codes This procedure lets you associate codes with the relays on the audio module MTM/01, the video module MTMV/01, or on any eventual VLS/2. For example, you can open the front door with a code, or switch on the stairwell lighting with another code. F Press the key and 0, 1, 2 or 3 to identify the relay (see table). Press key and the code to be associated (from 3 to 5 digits) with the relay. Press key again: a will confirm the relay association procedure G. Key Command uxiliary contact Door release contact Relay 1 on module VLS/2 Relay 2 on module VLS/2 The door-release and relay code programming procedure deletes all the previously programmed codes. G Exiting Programming V/01 H MTM/01 MTMV/01 I With V/01 Briefly press the key H. With MTM/01-MTMV/01 without V/01 Briefly press the key on the entry panel I. The LED on the entry panel and the LED on the power supply go out. Page 4 - Manual FB00748-EN - vers. 1-04/2017- Came S.p.. - The contents of this manual may be changed, at any time, and without notice.

5 RMMING THE CLL CODES This programming is available only with audio module MTM/08 and video module MTMV/08. Call programming associates a call code with each internal receiver. Going into Programming V/08 >3 s Press the key until the LED lights up. The LED will flash to signal entry into programming B. Page 5 - Manual FB00748-EN - vers. 1-04/2017- Came S.p.. - The contents of this manual may be changed, at any time, and without notice. Programming the call codes C D Exiting Programming V/08 >3 s E B Briefly press the key E. The Press the door-release and UX2 keys and enter the group call code (from 1 to 98) followed by key : The call code is associated with the internal receiver or the call key chosen C and D. Continue, repeating the same operations for all the other internal receivers. The operation can only be carried out from the entry panel with the LED off. To change the entry panel from which to carry out call programming, you must press key 1 followed by key. LED on the entry panel and the LED on the power supply go out.

6 RMMING CCESS CONTROL NUMBER CODES This procedure lets you associate number codes with a group of users, or remove them, for control of door release in audio module MTM/01, MTM/08 and video module MTMV/01, MTMV/08. maximum of 5 number codes can be associated per group. dding number codes V/01 - V/08 C D E + Ð + Ð RFID V/01 - V/08 RFID B beeeep Put the RFID jumper in the "+" position. The LED on the power supply and the and LEDs will flash quickly and B. Press key, enter the access code (4 to 8 digits long) followed by key C. If the code is valid, the LED stays constantly on and it is possible to continue with programming. Enter the group call code, or press the call key associated with the group, followed by key D. long will confirm the procedure was correct. In the event of an error, this will be indicated by 3 fast s. Repeat the stage correctly. When programming is completed, place the RFID jumper as shown in figure E. Page 6 - Manual FB00748-EN - vers. 1-04/2017- Came S.p.. - The contents of this manual may be changed, at any time, and without notice.

7 Deleting number codes V/01 - V/08 F + Ð RFID G Put the RFID jumper in the position. The LED on the power supply and the and LEDs will flash slowly F and G. To delete the number codes relating to a group, press, enter an access code (4 to 8 digits long) associated with the group, followed by key H. Page 7 - Manual FB00748-EN - vers. 1-04/2017- Came S.p.. - The contents of this manual may be changed, at any time, and without notice. H I J beeeep If the code is valid, the LED stays constantly on and it is possible to continue with programming. Press key, enter the access code again and press key again to confirm the operation. long will confirm the procedure was correct. In the event of an error, this will be indicated by 3 fast s. Repeat the stage correctly. To delete all the codes relating to a group, enter the call code, or press the call key associated with the group, followed by key I. If the code is valid, the LED stays constantly on and it is possible to continue with programming. Enter the call code again, or press the call key associated with the group, followed by key J. long will confirm the procedure was correct. In each of the two stages of deletion any error condition will be signalled by three fast s. Repeat the stage correctly.

8 V/01 - V/08 When programming is completed, place the RFID jumper as shown in figure K. K + Ð RFID USE OF KEYPD MODULE Used as access control Press key, enter the access code (3 to 8 digits long) and press key again: if the code is valid a confirmation will sound and the LED will come on, otherwise 3 fast s will signal an error condition. Used to make calls B Enter the call code (1 98), followed by key : if the code is valid the call will be made and the LED will come on B. This product complies with the relevant directives in force. Decommissioning and disposal. Dispose of the packaging and the device at the end of its life cycle responsibly, in compliance with the laws in force in the country where the product is used. The recyclable components are marked with a symbol and the material's ID marker. THE DT ND INFORMTION SHOWN IN THIS MNUL RE TO BE CONSIDERED S SUBJECT TO CHNGE T NY TIME ND WITHOUT THE NEED FOR NY DVNCE WRNING. MESUREMENTS, UNLESS OTHERWISE INDICTED, RE IN MILLIMETRES. English - Manual FB00748-EN - vers. 1-04/2017- Came S.p.. The contents of this manual may change, at any time, and without notice. Came S.p.. Via Martiri Della Libertà, 15 Via Cornia, 1/b - 1/c Dosson di Casier Treviso - Italy (+39) (+39) Sesto al Reghena Pordenone - Italy (+39) (+39)