Audio GSM module for modular plate

Transcription

1 Audio GSM module for modular plate FB00758-EN PROGRAMMING MANUAL MTMA/GSM

2 A General precautions Read the instructions carefully before beginning the installation and carry out the actions as specified by the manufacturer. The installation, programming, commissioning and maintenance of the product must only be carried out by qualified technicians, properly trained in compliance with the regulations in force, including health and safety measures and the disposal of packaging. Before carrying out any cleaning or maintenance operation, disconnect the device from the power supply. The equipment must be destined solely for the use for which it was expressly designed. The manufacturer declines all liability for any damage as a result of improper, incorrect or unreasonable use. DESCRIPTION Audio module for Dual Band GSM systems. The module can make audio calls in speaker mode to telephone numbers on fixed and mobile networks, via the pressing of call buttons or entry of codes on MTMKB keypads. From the phone, you can open the door or activate the AUX relay using the numerical keypad to communicate or the dial to open function. Main features Maximum 98 call keys (12 MTM8C modules). Option to manage a contacts list containing a maximum of 1000 telephone numbers, which may possibly be organised into groups. A group can be made up of a minimum of 1 and a maximum of 5 telephone numbers Each group can be associated with a call key (see section 3. Associating a group of users with a call key on the entry panel). The numbering of the keys follows the logic show in figure A, according to which key 1 is associated with group 1, key 2 with group 2, etc.; a call order is associated with the telephone numbers that make up a group, to be used to manage call diversion when there is no answer B Page 2 - Manual FB00758-EN - vers. 1-06/2017- Came S.p.A. - The data and information shown in this manual are to be considered subject to change at any time and without the need for any advance warning.

3 Page 3 - Manual FB00758-EN - vers. 1-06/2017- Came S.p.A. - The data and information shown in this manual are to be considered subject to change at any time and without the need for any advance warning. B Call the telephone numbers associated with group 4. Call the first number in group 4, if there is no answer, call the second number in group 4, if there is no answer, etc. Call the telephone numbers associated with group 6. Call the first number in group 6, if there is no answer, call the second number in group 6, if there is no answer, etc. The telephone numbers in the contacts list (maximum 1000) can be authorised to command relays on board and/or associated with the call keys; for example, it is possible to call the module from a number (that has the correct authorisations) to operate the solenoid lock or the entry panel's on-board relay. The MTMAGSM module combined with the MTMKB module makes available up to 2000 codes to manage the activation of door releases and relays; it is also possible to associate a customised call code with each group. COMMISSIONING THE DEVICE Preliminary operations Note: The micro-sim card (not included) must be enabled for 2G data traffic and for sending and receiving SMS messages. Check the availability and costs of these services with your mobile phone operator. Note: Make sure that module MTMAGSM has no power and that the SIM card's PIN code has been disabled. Before inserting the micro-sim card into module MTMAGSM, it is advisable to test the sending and receiving of SMS messages by using the micro-sim on a normal mobile phone, in the proximity of the area in which you intend to install the device. Module start-up Insert the micro-sim card into its housing as shown in the installation instructions. Connect the external aerial to the module socket and power the system. During start-up all the call button LEDs flash at the same time; calls cannot be made during this stage. optimum operation only once registration has been completed, and where there is a good GSM signal. Checking connection to GSM network status Press and hold down the PROG button; the LED above the button provides the following signals: Flashing quickly (< 2 seconds) = Flashing slowly (> 2 seconds) = The module is ready for Module not registered with network Module registered with network

4 OPERATIONS THAT CAN BE CARRIED OUT FROM THE TELEPHONE During the conversation between the telephone and the entry panel, it is possible to carry out the following operations using the telephone keypad: Increase the speaker volume Lower the speaker volume Activate the solenoid lock PROGRAMMING VIA SMS * 0 # Adjusting the speaker volume (for call in progress) If during the conversation the person you are talking to cannot hear your voice at the right volume, you can increase the speaker volume by pressing key 1, or lower it by pressing key 4. Adjusting the microphone volume (for call in progress) If you can't hear the voice of the person in front of the audio entry panel, you can press key 3 to increase or key 6 to reduce the sensitivity of the microphone. Programming via SMS requires the sending of individual SMS composed in such a way as to contain the information required to programme the entry panel. Access to the entry panel is password protected; the factory settings set the password at "0000". General information on the composition of a programming SMS The text of a valid programming SMS starts with the password assigned to the entry panel. For example, if the access password is still the default one: One or more commands to programme the device can be added to this sequence; each command or sequence of commands message must end with the symbol #. The different types of commands are identified by a numerical code. If the commands are for the purpose of setting parameters, each of the data items to be set is preceded by the character. (see table of commands). Each command can be sent in an individual SMS and must be preceded by the symbol #. For example if you want to change the default password (0000) for a new password (1234), the command code is 10 and the SMS to key in is: # # Increase the microphone volume Lower the microphone volume Activate the entry panel on-board relay End the call Page 4 - Manual FB00758-EN - vers. 1-06/2017- Came S.p.A. - The data and information shown in this manual are to be considered subject to change at any time and without the need for any advance warning.

5 Alternatively, an individual SMS can contain a series of commands, each preceded by the symbol #, on condition that the length of the SMS does not exceed the maximum number of characters permitted for a single SMS. Page 5 - Manual FB00758-EN - vers. 1-06/2017- Came S.p.A. - The data and information shown in this manual are to be considered subject to change at any time and without the need for any advance warning. If the programming SMS contains more than one parameter, these must always be preceded by the symbol.. Example of SMS with chain of numerical commands and parameters: # # # # If there is some text amongst the command parameters, it must be written between the characters. Example of SMS with chain of commands containing numerical parameters and text labels: # # C A M E G R O U P # # If you want to use a command that is for setting various miscellaneous parameters (for example, the command that sets the ring time and conversation time), leaving one of the values unchanged, you must compose the SMS leaving empty fields in the space reserved for the parameters that are not to be changed (.. ). Example of SMS in which the command requires the setting of two parameters and you want to programme only the second of the two, leaving the first unchanged: # # To know the outcome of sending one or more commands to the entry panel, enter the character? at the end of the desired command(s), before the symbol #. Example of programming SMS with request for outcome for the first parameter programmed: # ? # C A M E G R O U P # The message received in response to the SMS in the example can have 3 different outcomes and, therefore, contents: 20OK = The command has been received and carried out correctly, 20E1 = The command contains wrong parameters, 20E2 = The command has not been carried out. For commands that require a reply SMS (e.g. request for GSM signal strength or request for firmware version of connected modules), enter character? at the end of the command and before symbol #. Example of SMS that requires a reply SMS: 8 0? #

6 Functions and list of programming commands Each command or group of commands SMS must be preceded by the password and end with #. Function carried out by command Content of SMS 1. Changing the password. #10.New password 2. Associating a telephone number with a group. #20.Group. Order. Telephone number 3. Associating a group of users with a call key on the entry panel. #21.Group. Key 4. Associating a name with a group. #22.Group. "Name" 5. Associating a call number code (to be entered on MTMKB keypads) with a group. 6. Authorising a telephone number to activate the doorrelease output and/or relay output. 7. Authorising a number code, entered on MTMKB keypads, to activate the door-release output or relay output. #23.Group. 8. Deleting information relating to a group. #90.Group 9. Deleting a telephone number and the activations associated with it. 10. Deleting the number codes associated with a user, authorised to activate the door-release output and/or relay output. 11. Deleting all the telephone numbers stored and the relative groups they belong to. 12. Deleting all the number codes (to be entered on MTMKB keypads) associated with activations. #24.Enable door-release. Enable relay. Telephone number #25.Enable door-release. Enable relay. User ID. #91.Telephone number #92.User ID #93.Password #94.Password 13. Programming the ring time and call conversation time. #50.Ring time. Conversation time 14. Programming the door-release relay and/or auxiliary relay activation time. 15. Choosing the colour and brightness of the keypad backlighting of all the modules that make up the entry panel. #51.Door-release relay activation time. Auxiliary relay activation time #52 Colour. Brightness 16. Programming the function of terminals I1 and I2. #53.Function of terminal l1. Function of terminal l2 17. Choosing the interface language for MTMDY and MTMBFVS modules. 18. Programming the general parameters of the MTMDY display module. 19. Adjusting the volume of the entry panel speaker and microphone. #54.Interface language #55.Colour. Brightness. Stand-by. Brightness in stand-by mode. Search ranges. Range limit #60.Speaker volume. Microphone volume 20. Setting up the message tones. #61.Key press tone. Solenoid lock tone. Messages tone. Voice messages 21. Requesting the GSM signal strength of the module #80? 22. Requesting the module to be called back. # Requesting the firmware version of the modules #82.Module? installed Page 6 - Manual FB00758-EN - vers. 1-06/2017- Came S.p.A. - The data and information shown in this manual are to be considered subject to change at any time and without the need for any advance warning.

7 Description of individual programming commands Warning: Each programming SMS must be preceded by the password and end with the symbol # ( for example # ). An SMS that is not composed in the correct way will result in the command not being carried out. 1. Changing the password Page 7 - Manual FB00758-EN - vers. 1-06/2017- Came S.p.A. - The data and information shown in this manual are to be considered subject to change at any time and without the need for any advance warning. A 1 0. New password # A - Enter the new programming password. The password is a numerical code with a maximum of 8 digits. 2. Associating a telephone number with a group A B C 2 0. Group. Order. Telephone number # A - Enter a number with a maximum of 4 digits. The number identifies a group of a minimum of 1 and maximum of 5 telephone numbers. Note: A group does not necessarily have to be connected to a call key. B - Enter a number from 1 to 5. The number sets the order within the group in which the telephone number (C) is called if the previous number does not answer. C - Enter the user's telephone number. Note: Do not use the international prefix for national calls. 3. Associating a group of users with a call key on the entry panel A B 2 1. Group. Key # A - Enter a number with a maximum of 4 digits. The number identifies a group of a minimum of 1 and maximum of 5 telephone numbers. B - Enter a number from 1 to 98 (based on the call keys present on the system). The number sets which key on the entry panel, once pressed, generates a call to the numbers that make up the group (A). Note: see figures A and B for details about the numbering of call keys. 4. Associating a name with a group The command lets you display the names of the users in the MTMDY module's contacts list. Note: Before assigning any name, it is good practice to delete the telephone numbers present so as to avoid overlaps with a pre-existing contacts list. A B 2 2. Group. Name # A - Enter a number with a maximum of 4 digits. The number identifies a group of a minimum of 1 and maximum of 5 telephone numbers. B - Enter text. The text constitutes the name of the group (A) and can be viewed on the MTMDY module's display screen if there is one in the system.

8 5. Associating a call number code (to be entered on MTMKB keypads) with a group A B 2 3. Group. # A - Enter a number with a maximum of 4 digits. The number identifies a group of a minimum of 1 and maximum of 5 telephone numbers. B - Enter a number with a maximum length of 8 digits. 6. Authorising a telephone number to activate the door-release output and/or relay output The user with whom the authorised number is matched (C) can activate the door-release output and/or relay output with a simple call to the number matched with the entry panel. Note: The number must have already been associated with a group using code 20. A B C 2 4. Enable door-release. Enable relay. Telephone number # A - Enter 1 or 0 in this field. 1 = The telephone number shown in field "C" is authorised to activate the door-release output. 0 = The telephone number shown in field "C" is not authorised to activate the door-release output. B - Enter 1 or 0 in this field. 1 = The telephone number shown in field "C" is authorised to activate the relay output. 0 = The telephone number shown in field "C" is not authorised to activate the relay output. C - Enter the telephone number that is authorised. Note: the fields (A or B) left empty do not cause any change to existing programming. 7. Authorising a number code, entered on MTMKB keypads, to activate the door-release output and/or relay output Note: Multiple number codes can be associated with each user. The number codes must all be different. A B C D 2 5. Enable door-release. Enable relay. User ID. # A - Enter 1 or 0 in this field. 1 = The call number code shown in field "C" is authorised to activate the door-release output. 0 = The call number code shown in field "C" is not authorised to activate the door-release output. B - Enter 1 or 0 in this field. 1 = The call number code shown in field "C" is authorised to activate the relay output. 0 = The call number code shown in field "C" is not authorised to activate the relay output. C - In this field enter a number with a maximum of 4 digits that identifies the User associated with the code. Note: the purpose of the User ID number is to make the eventual removal of the code simpler. D - Enter the number code (minimum 3, maximum 8 digits). Note: the fields (A or B) left empty do not cause any change to existing programming. Page 8 - Manual FB00758-EN - vers. 1-06/2017- Came S.p.A. - The data and information shown in this manual are to be considered subject to change at any time and without the need for any advance warning.

9 8. Deleting information relating to a group A Page 9 - Manual FB00758-EN - vers. 1-06/2017- Came S.p.A. - The data and information shown in this manual are to be considered subject to change at any time and without the need for any advance warning Group # A - Enter a number with a maximum of 4 digits; the number identifies the group for which all information is to be removed. Note: the command removes the telephone numbers belonging to the group. If a telephone number is associated with more than one group, it will only be removed from the group the command is addressed to. 9. Deleting a telephone number and its associated activations A 9 1. Telephone number # A - Enter the telephone number that you want to delete. Note: the telephone number will be removed from all the groups it belongs to. 10. Deleting the number codes associated with a user, authorised to activate the door-release output or relay output A 9 2. User ID # A - Enter the number code. NOTE: This command removes ALL codes associated with a user ID 11. Deleting all the telephone numbers stored and the relative groups they belong to A 9 3. Password # A - Enter the programming password. 12. Deleting all the number codes (to be entered on MTMKB keypads) associated with activations A 9 4. Password # A - Enter the programming password.

10 13. Programming the ring time and call conversation time A B 5 0. Ring time. Conversation time # After pressing a call button or entering a call code on MTMKB keypads, the entry panel generates a call to the first number associated with the group called (from 1 to 5 numbers); once the ring time (A) has elapsed without any reply, the entry panel will call the second number in the group (if there is one), etc. When one of the numbers answers the call, the conversation time counter (B) starts, at the end of which, if still in progress, the communication will be interrupted. A - Enter a value between 1 and 90 seconds (pre-set 3 0 ). B - Enter a value between 1 and 240 seconds (pre-set 6 0 ). Note: These settings could be affected by the GSM network and/or the device receiving the call. Note: the conversation time counter is started even if a voice mail service answers the call, therefore the call is considered to have been successful. Note: the fields left empty do not cause any change to existing programming. 14. Programming the door-release relay and/or auxiliary relay activation time A B 5 1. Door-release relay activation time. Auxiliary relay activation time # A - Enter a value between 1 and 10 seconds (pre-set 1 ). B - Enter a value between 1 and 3600 seconds (pre-set 1 ). Note: the fields left empty do not cause any change to existing programming. 15. Choosing the colour and brightness of the keypad backlighting of all the modules that make up the entry panel A B 5 2. Colour. Brightness # A - Enter 1 or 0 in this field (pre-set 0 ). 1 = The backlighting colour is white. 0 = The backlighting colour is blue. B - In this field enter values between 0 and 4 (pre-set 2 ). 0 = Off 1 = Brightness 25% 2 = Brightness 50% 3 = Brightness 75% 4 = Brightness 100%. Note: the fields left empty do not cause any change to existing programming. 16. Programming the function of terminals I1 and I2 A B 5 3. Function of terminal l1. Function of terminal l2 # A - Enter 1 or 0 in this field (pre-set 0 ). 1 = The terminal functions as a relay activation button input. 0 = The terminal functions as a call 1 input. B - Enter 1 or 0 in this field (pre-set 0 ). 1 = The terminal functions to activate external video camera. 0 = The terminal functions as a call 2 input. Note: the fields left empty do not cause any change to existing programming. Page 10 - Manual FB00758-EN - vers. 1-06/2017- Came S.p.A. - The data and information shown in this manual are to be considered subject to change at any time and without the need for any advance warning.

11 17. Choosing the interface language for MTMDY and MTMBFVS modules A 5 4. Interface language # Page 11 - Manual FB00758-EN - vers. 1-06/2017- Came S.p.A. - The data and information shown in this manual are to be considered subject to change at any time and without the need for any advance warning. A - In this field enter one of the following values (pre-set 1 ). 1 = English, 2 = Italian, 3 = French, 4 = German, 5 = Portuguese, 6 = Spanish, 7 = Dutch, 8 = Polish, 9 = Russian, 1 0 = Hungarian, 1 1 = Ukrainian, 1 2 = Croatian, 1 3 = Swedish, 1 4 = Norwegian, 1 5 = Finnish, 1 6 = Danish, 1 7 = Latvian, 1 8 = Slovenian, 1 9 = Estonian, 9 9 = Customised Note: the availability of the language set does depend, however, on the availability of that language in the MTMDY and MTMBFVS modules installed. 18. Programming the general parameters of the MTMDY display module A B C D E F 5 5. Colour. Brightness. Stand-by. Brightness in stand-by. A - Sets the colour of the module backlighting. B - Enter 1 or 0 in this field (pre-set 0 ). 1 = The backlighting colour is white. 0 = The backlighting colour is blue. Search ranges. B - Sets the brightness of the module backlighting. In this field enter values between 0 and 4 (pre-set 4 ). 0 = Off 1 = Brightness 25% 2 = Brightness 50% 3 = Brightness 75% 4 = Brightness 100%. C - Sets whether to activate stand-by mode (pre-set 0 ). 1 = Stand-by mode enabled. 0 = Stand-by mode not enabled. D - Sets the module's backlighting brightness in stand-by mode (pre-set 1 ). 1 = In stand-by mode the display is on with minimal brightness. 0 = In stand-by mode the display is off. E - Sets how many parts to divide the contacts list into to make it easier to view on the display. (pre-set 2 ). Enter a value between 1 and 4 in this field. Note: With value 1, the list of names in the contacts list is not divided into parts. F - Sets the maximum number of names permitted for each search range. (pre-set 1 0 ). Beneath this range limit the contacts list is no longer divided into parts. Note: the fields left empty do not cause any change to existing programming. 19. Adjusting the volume of the entry panel speaker and microphone A B 6 0. Speaker volume. Microphone volume # A - In this field enter values between 0 and 100 (pre-set 4 0 ). B - In this field enter values between 0 and 15 (pre-set 1 0 ). Note: the fields left empty do not cause any change to existing programming. Range limit #

12 20. Setting up the message tones A B C D 6 1. Key press tone. Solenoid lock tone. Messages tone. Voice messages # A - Enter 1 or 0 in this field (pre-set 1 ). 1 = Key press tone enabled. 0 = Key press tone not enabled. B - Sets whether activation of the solenoid lock must be accompanied by an acoustic signal. B - Enter 1 or 0 in this field (pre-set 1 ). 1 = Activation tone enabled. 0 = Activation tone not enabled. C - Sets whether entering a correct/incorrect activation code must be accompanied by an acoustic signal. B - Enter 1 or 0 in this field (pre-set 1 ). 1 = Confirmation/error tone enabled. 0 = Confirmation/error tone not enabled. D - Sets whether to activate voice messages audible even by the hearing-impaired from module MTMBFVS (pre-set 1 ). 1 = Voice messages enabled. 0 = Voice messages not enabled. Note: the fields left empty do not cause any change to existing programming. 21. Requesting the GSM signal strength of the module Note: The command does not require parameters. 8 0? # The reply message gives the signal strength detected in the following form: Text of reply message Signal strength detected (dbm) [ ] Unknown or not detectable [ + ] < -103 (poor quality of outgoing calls) [ ++ ] from -103 to -94 (poor quality of outgoing calls) [ ++ + ] from -93 to -90 [ ] from -89 to -84 [ ] from -83 to -80 [ ] from -79 to -74 [ _ ] from -73 to -62 [ ] from -61 to Requesting the module to be called back Note: The command does not require parameters. 8 1 # Following correct sending of the message, the module makes a call to the number that sent the SMS. Page 12 - Manual FB00758-EN - vers. 1-06/2017- Came S.p.A. - The data and information shown in this manual are to be considered subject to change at any time and without the need for any advance warning.

13 23. Requesting the firmware version of the modules installe A 8 2. Module? # Page 13 - Manual FB00758-EN - vers. 1-06/2017- Came S.p.A. - The data and information shown in this manual are to be considered subject to change at any time and without the need for any advance warning. A - In this field enter the number that identifies the module whose firmware version you want to know. 1 = Request firmware version of MTMAGSM module. 2 = Request firmware version of MTMKB module. 3 = Request firmware version of MTMDY module. 4 = Request firmware version of MTMINFO module. 5 = Request firmware version of MTMBFVS module. from 10 to 21 = Request firmware version of MTM8C modules. 10 identifies the first MTM8C module connected, code 11 the next one in the cabling that connects the modules to each other, etc., up to a maximum of 12 MTM8C modules. RESTORE FACTORY DEFAULT To restore the entry panel to the default settings, remove the power supply, press and hold the two call buttons on the unit and power the device. After 5 seconds the entry panel restarts. NOTE. If the entry panel does not restart, it has not been restored to default settings. The product complies with the relevant directives in force. Decommissioning and disposal. Dispose of the packaging and the device responsibly at the end of its life cycle, in compliance with the laws in force in the country where the product is used. The recyclable components are marked with a symbol and the material's ID marker. THE DATA AND INFORMATION SHOWN IN THIS MANUAL ARE TO BE CONSIDERED AS SUBJECT TO CHANGE AT ANY TIME AND WITHOUT THE NEED FOR ANY ADVANCE WARNING. MEASUREMENTS, UNLESS OTHERWISE INDICATED, ARE IN MILLIMETRES.

14 Page 14 - Manual FB00758-EN - vers. 1-06/2017- Came S.p.A. - The data and information shown in this manual are to be considered subject to change at any time and without the need for any advance warning.

15 Page 15 - Manual FB00758-EN - vers. 1-06/2017- Came S.p.A. - The data and information shown in this manual are to be considered subject to change at any time and without the need for any advance warning.

16 English - Manual FB00758-EN - vers. 1-06/ Came S.p.A. The data and information shown in this manual are to be considered subject to change at any time and without the need for any advance warning. Came S.p.A. Via Martiri Della Libertà, 15 Via Cornia, 1/b - 1/c Dosson di Casier Treviso - Italy (+39) (+39) Sesto al Reghena Pordenone - Italy (+39) (+39)