ExSite Series Explosionproof Camera Module

Size: px

Start display at page:

Download "ExSite Series Explosionproof Camera Module"

James Young
5 years ago
Views:

1 I N S T A L L A T I O N ExSite Series Explosionproof Camera Module C1303M-C (11/08)

2 Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not block any ventilation openings. Install in accordance with the manufacturer s instructions. 6. To reduce the risk of ignition of hazardous atmospheres, disconnect the equipment from the supply circuit before opening. Keep assembly tightly closed when in operation. 7. The maximum ambient temperature range is -76 F to 140 F (-60 C to 60 C). 8. Only use attachments/accessories specified by the manufacturer. 9. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 10. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as powersupply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 11. Installation should be done only by qualified personnel and conform to all local codes. 12. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is designed for indoor use only and it must not be installed where exposed to rain and moisture. 13. Use only installation methods and materials capable of supporting four times the maximum specified load. 14. Use stainless steel hardware to fasten the mount to outdoor surfaces. 15. AN ALL-POLE MAINS SWITCH with a contact separation of at least 3 mm in each pole shall be incorporated in the electrical installation of the building. 16. A readily accessible disconnect device shall be incorporated in the building installation wiring. 17. CAUTION: These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other that contained in the operating instructions unless you are qualified to do so. 18. Only use replacement parts recommended by Pelco. The product and/or manual may bear the following marks: This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit. This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit. CAUTION: RISK OF ELECTRIC SHOCK. DO NOT OPEN. WARNING: HAZARDOUS MOVING PARTS. KEEP FINGERS AND OTHER BODY PARTS AWAY. WARNING: To reduce the risk of ignition of hazardous atmospheres, disconnect the equipment from the supply circuit before opening. Keep assembly tightly closed when operating. WARNING: To reduce the risk of ignition of hazardous atmospheres, conduit runs must have a sealing fitting connected within 2 inches of the enclosure. TO REDUCE THE RISK OF IGNITION, DO NOT OPEN WHEN AN EXPLOSIVE GAS ATMOSPHERE MAY BE PRESENT. 2 C1303M-C (11/08)

3 Getting Started Thank you for purchasing Pelco s ExSite Series explosionproof integrated positioning system. This manual includes instructions for installing the camera module for the ExSite Series system. For complete system installation instructions, refer to the installation manual placed in the pan and tilt box. WARNING: Do not connect the power module to a supply circuit unless all ExSite system components (pan and tilt, camera module, and power module) are installed. Once the complete system is installed, refer to the operation/programming manual shipped with the camera module for instructions on how to operate and program your system. C1303M-C (11/08) 3

4 Installation To install the camera module do the following: 1. Loosen the set screw at the back of the enclosure with the provided 1.5 mm Allen wrench (refer to Figure 1). SET SCREW Figure 1. Loosen Setscrew 2. Use the supplied spanner wrench to loosen the back of the camera enclosure (refer to Figure 2). Once the back is loose, use your hands to continue to loosen it until it can be removed. WARNING: To avoid thread damage, carefully remove the back of the enclosure. Never use force to remove the back of the camera enclosure. ENCLOSURE BACK SPANNER WRENCH Figure 2. Remove Back Cap of Enclosure 4 C1303M-C (11/08)

5 3. Slide the camera module into the enclosure. Refer to Figure 3 to position the camera module properly in the enclosure. Carefully mate the camera s power connector to the mating connector located inside the enclosure. Only models with wipers: The tab located inside the enclosure must be pointing down before installing the camera module (refer to Figure 3). To position the tab, place the wiper located at the front of the enclosure in the center of the viewing window (refer to Figure 4). WARNING: Do not force the camera module into the enclosure. TAB CENTER NOTCHES MODULE ENCLOSURE Figure 3. Install Camera Module CENTER WIPER Figure 4. Center Wiper C1303M-C (11/08) 5

6 4. Refer to Figure 5 and do the following to install the arm of the wiper: a. Place the supplied green bushing on the stud located behind the handle of the camera module. The bushing should be in the same orientation as shown in Figure 5. b. Install the wiper arm. Place the ridge of the arm in the notch of the enclosure tab and the slot of the arm over the green bushing. 5. Secure the arm of the wiper and the camera module with the supplied 8-32 Phillips flat head screw (refer to Figure 5). SET TAB IN CENTER POSITION 8-32 PHILLIPS FLAT HEAD SCREW ARM STUD Figure 5. Install Wiper Arm BUSHING MODULE HANDLE WARNINGS: To avoid thread damage, carefully install the back cap to the enclosure. Never force the back cap onto the end of the enclosure. When installation is completed, there should be no gap between the back cap and the enclosure. 6. Reinstall the back cap on the enclosure by doing the following: a. Use your hands and turn the back cap clockwise until you can no longer turn it with your hands. The back cap should turn easily until it comes in contact with the O-ring. If it does not turn easily, the threads are not aligned and thread damage will occur. b. Continue tightening the back cap with the supplied spanner wrench. There should be no gap between the back cap and the enclosure when the back cap is tightened and properly installed. c. Once the back cap is installed, secure the back cap with the set screw using the supplied 1.5 mm Allen wrench. 6 C1303M-C (11/08)

7 Maintenance MODULE REPLACEMENT The ExSite camera module can be replaced only with a camera module with the same model number. If a different camera model is installed in an existing system, the system will not function and a message to contact the Pelco factory will appear on the screen. DANGER: To reduce the risk of ignition of hazardous atmospheres, disconnect the equipment from the power supply before opening. Keep assembly tightly closed when operating. To replace the camera module do the following: 1. Remove the back cap of the camera enclosure. Refer to Figure 6 and do the following: a. Loosen the set screw with a 1.5 mm Allen wrench. b. Use the supplied spanner wrench to loosen the back cap of the camera enclosure. Once the back is loose, use your hands to continue to loosen it until it can be removed. ENCLOSURE BACK SET SCREW SPANNER WRENCH Figure 6. Remove Back Cap of Camera Enclosure 2. Remove the 8-32 Phillips flat head screw that secures the camera module inside the enclosure, refer to Figure 7. SET TAB IN CENTER POSITION 8-32 PHILLIPS FLAT HEAD SCREW ARM STUD BUSHING Figure 7. Remove or Install Camera Module MODULE HANDLE C1303M-C (11/08) 7

8 3. For models with wipers, also remove the wiper arm and the green bushing from the unit (refer to Figure 7). 4. Slide the camera module out of the enclosure. WARNING: Never force the camera module into the enclosure. 5. Install the new camera module by doing the following: Slide the camera module into the enclosure. Refer to Figure 8 to position the camera module properly in the enclosure. Carefully mate the camera s power connector to the mating connector located inside the enclosure. Only models with wipers: The tab located inside the enclosure must be pointing down before installing the camera module (refer to Figure 8). To position the tab, place the wiper located at the front of the enclosure in the center of the viewing window (refer to Figure 9). TAB CENTER NOTCHES MODULE ENCLOSURE Figure 8. Install Camera Module CENTER WIPER Figure 9. Center Wiper 8 C1303M-C (11/08)

9 6. Refer to Figure 7 and do the following to reinstall the arm of the wiper: a. Reinstall the green bushing on the stud located behind the handle of the camera module. b. Reinstall the wiper arm. Place the ridge of the arm in the notch of enclosure tab and the slot of the arm over the green bushing. 7. Secure the camera module and the wiper arm with the 8-32 Phillips flat head screw (refer to Figure 7). WARNINGS: To avoid thread damage, carefully install the back cap to the enclosure. Never force the back cap onto the end of the enclosure. When installation is completed, there should be no gap between the back cap and the enclosure. 8. Reinstall the back cap on the enclosure by doing the following: a. Use your hands and turn the back cap clockwise until you can no longer turn it with your hands. The back cap should turn easily until it comes in contact with the O-ring. If it does not turn easily, the threads are not aligned and thread damage will occur. b. Continue tightening the back cap with the supplied spanner wrench. There should be no gap between the back cap and the enclosure when the back cap is tightened and properly installed. c. Once the back cap is installed, secure the back cap with the set screw using a 1.5 mm Allen wrench. C1303M-C (11/08) 9

10 Specifications Camera Day/Night (23X) Color LowLight (22X) Color Signal Format NTSC, PAL NTSC, PAL Scanning System 2:1 interlace 2:1 Interlace Image Sensor 1/4-inch progressive scan CCD 1/4-inch EXview HAD CCD Effective pixels NTSC PAL Horizontal Resolution NTSC PAL 768 (H) x 494 (V) 752 (H) x 582 (V) 540 TV lines 540 TV lines 768 (H) x 494 (V) 752 (H) x 582 (V) >470 TV lines >460 TV lines Lens f/1.6 (focal length, 3.6~82.8 mm optical) f/1.6 (focal length, 4~88 mm optical) Zoom 23X optical, 10X digital 22X optical, 12X digital Zoom Speed 2.9/4.2/5.8 seconds 2.4/3.9/6.3 seconds Horizontal 54 at 3.6 mm wide zoom 47 at 4.0 mm wide zoom Angle of view 2.5 at 82.8 mm telephoto zoom 2.2 at 88 mm telephoto zoom Focus Automatic with manual override Automatic with manual override Maximum Sensitivity at 35 IRE NTSC PAL Sync System lux at 1/2 sec shutter (color) 0.1 lux at 1/60 sec shutter (B-W) lux at 1/2 sec shutter (B-W) lux at 1/1.5 sec shutter (color) 0.1 lux at 1/50 sec shutter (B-W) lux at 1/1.5 sec shutter (B-W) Internal/AC line lock, phase adjustable using remote control, V-Sync* 0.02 lux at 1/2 sec shutter 0.02 lux at 1/1.5 sec shutter Internal/AC line lock, phase adjustable using remote control, V-Sync* White Balance Automatic with manual override* Automatic with manual override* Shutter Speed NTSC PAL Automatic (electronic iris)/manual 1/2~1/30,000* 1/1.5~1/30,000* Automatic (electronic iris)/manual 1/2~1/30,000* 1/1.5~1/30,000* Iris Control Automatic Iris Control with manual override* Automatic Iris Control with manual override* Gain Control Automatic/OFF* Automatic/OFF* Video Output 1 Vp-p, 75 ohms 1 Vp-p, 75 ohms Video Signal to Noise >50 db >50 db *Manual control of camera setup functions can be done with CM6700, CM6800, CM8500, CM9500, CM9740, CM9760, CM9770, CM9780, KBD200A, KBD300A, and MPT9500 controllers, but not with CM7500, MPT9000, or KBD9000 controllers. 10 C1303M-C (11/08)

11 PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: Five years: Fiber optic products TW3000 Series unshielded twisted pair (UTP) transmission products CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models Three years: Pelco-branded fixed camera models (CCC1390H Series, C10DN Series, C10CH Series, and IP3701H Series) EH1500 Series enclosures Spectra IV products (including Spectra IV IP) Camclosure Series (IS, ICS, IP) integrated camera systems DX Series digital video recorders, DVR5100 Series digital video recorders, Digital Sentry Series hardware products, DVX Series digital video recorders, and NVR300 Series network video recorders Endura Series distributed network-based video products Genex Series products (multiplexers, server, and keyboard) PMCL200/300/400 Series LCD monitors Two years: Standard motorized or fixed focal length lenses DF5/DF8 Series fixed dome products Legacy Series integrated positioning systems Spectra III, Spectra Mini, Spectra Mini IP, Esprit, ExSite, and PS20 scanners, including when used in continuous motion applications. Esprit Ti and TI2500 Series thermal imaging products Esprit and WW5700 Series window wiper (excluding wiper blades). CM6700/CM6800/CM9700 Series matrix Digital Light Processing (DLP ) displays (except lamp and color wheel). The lamp and color wheel will be covered for a period of 90 days. The air filter is not covered under warranty. Intelli-M eidc controllers One year: Video cassette recorders (VCRs), except video heads. Video heads will be covered for a period of six months. Six months: All pan and tilts, scanners, or preset lenses used in continuous motion applications (preset scan, tour, and auto scan modes). Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment. All goods requiring warranty repair shall be sent freight prepaid to a Pelco designated location. Repairs made necessary by reason of misuse, alteration, normal wear, or accident are not covered under this warranty. Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products. Pelco s liability for any claim, whether based on breach of contract, negligence, infringement of any rights of any party or product liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for such Products. In no event will Pelco be liable for any special, incidental, or consequential damages (including loss of use, loss of profit, and claims of third parties) however caused, whether by the negligence of Pelco or otherwise. The above warranty provides the Dealer with specific legal rights. The Dealer may also have additional rights, which are subject to variation from state to state. If a warranty repair is required, the Dealer must contact Pelco at (800) or (559) to obtain a Repair Authorization number (RA), and provide the following information: 1. Model and serial number 2. Date of shipment, P.O. number, sales order number, or Pelco invoice number 3. Details of the defect or problem If there is a dispute regarding the warranty of a product that does not fall under the warranty conditions stated above, please include a written explanation with the product when returned. Method of return shipment shall be the same or equal to the method by which the item was received by Pelco. RETURNS To expedite parts returned for repair or credit, please call Pelco at (800) or (559) to obtain an authorization number (CA number if returned for credit, and RA number if returned for repair) and designated return location. All merchandise returned for credit may be subject to a 20 percent restocking and refurbishing charge. Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid The materials used in the manufacture of this document and its components are compliant to the requirements of Directive 2002/95/EC. This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002/96/EC of the European Union regarding the disposal of waste electrical and electronic equipment (WEEE). Contact your local dealer for procedures for recycling this equipment. REVISION HISTORY Manual # Date Comments C1303M 11/04 Original version. C1303M-A 2/05 Added maintenance section for camera module replacement. C1303M-B 5/05 Revised instructions for models with wipers. C1303M-C 11/08 Changed camera specs per CN Pelco, the Pelco logo, Camclosure, Digital Sentry, Endura, Esprit, ExSite, Genex, Intelli-M, Legacy, and Spectra are registered trademarks of Pelco, Inc. LowLight and Spectra III are trademarks of Pelco, Inc. DLP is a registered trademark of Texas Instruments Incorporated. EXview HAD is a trademark of Sony Corporation. Copyright 2008, Pelco, Inc. All rights reserved.

12 Pelco, Inc. Worldwide Headquarters 3500 Pelco Way Clovis, California USA USA & Canada Tel (800) Fax (800) International Tel +1 (559) Fax +1 (559)

WMVE-SR/WMVE-WT Rugged Environmental Wall Mounts

I N S T A L L A T I O N WMVE-SR/WMVE-WT Rugged Environmental Wall Mounts C2253M (1/11) Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow