exacqvision Edge/ISD Quick Start Guide

Size: px

Start display at page:

Download "exacqvision Edge/ISD Quick Start Guide"

Phebe Miller
6 years ago
Views:

1 Introduction exacqvision Edge is a variation of the standard exacqvision Server application that operates on a compatible ISD camera. It can record video from the local camera directly to the SD memory card in the camera. The exacqvision Client application can connect to any combination of embedded and standard servers simultaneously; however, the exacqvision Web Service cannot be supported on an embedded camera because of processing requirements. Requirements A one-channel license from Exacq Technologies must be obtained for each Edge-enabled camera. (A standard Edge license part number is EDGE, and an Edge Plus license part number is EDGEP.) exacqvision Edge is compatible with all ISD cameras: The camera must be running version 1.2 firmware or later. An SDHC Class 10 or better SD card or any SDXC card, purchased separately, is required for each camera. NOTE: Up to 2GB of space on each card is reserved for exacqvision Edge operations and cannot be used for exacqvision Edge data storage. Block Diagram Page 1 of 7

Installation and Configuration CAUTION: Connecting exacqvision Edge to another exacqvision server will result in unpredictable camera and server behavior. Do not attempt. 1.

2 Installation and Configuration CAUTION: Connecting exacqvision Edge to another exacqvision server will result in unpredictable camera and server behavior. Do not attempt. 1. Install the ISD camera and insert the SD memory card in the camera. NOTE: SD cards are normally pre-formatted to the FAT32 file system and automatically mounted when inserted. If you need to re-format an SD card, it can be done using the Format SD Card button on the General page. 2. Configure the camera s network parameters to communicate with a PC-based browser using the ISD Finder utility found on the CD shipped with the camera (ISD Camera Setup.exe), or downloaded from the ISD website. 3. If necessary, upgrade the camera firmware to the latest version from the ISD website. 4. Download the latest exacqvision Client application from the Exacq website at 5. Install the client software on your computer. 6. Download the latest exacqvision Edge server application from 7. Open a browser to the camera and log in. The default username and password are root and admin. 8. On the General page, select Install Edge. 8 Page 2 of 7

9. Complete the following steps on the Install Edge page, as shown in the following illustration: a. Select Choose File and then locate the Edge package file downloaded in step 6. b. Select Submit.

3 9. Complete the following steps on the Install Edge page, as shown in the following illustration: a. Select Choose File and then locate the Edge package file downloaded in step 6. b. Select Submit. It may take up to five minutes for the package to load and install. c. When the installation is complete, a status page will be displayed. Click Reboot on the status page to restart the camera. d. After the camera has restarted, return to the Settings/General page and verify the status. The exacqvision Edge status should now be Running. Note that after the first installation, or after the SD card is replaced, up to five minutes could elapse before the server software is ready to connect. 10. In the local exacqvision Client, add the remote embedded server on the Add System page using the default exacqvision Server username (admin) and password (admin256). This allows the local client on your computer to communicate with the embedded server on the camera. When complete, the server s status is displayed as Connected. Page 3 of 7

4 11. Add the exacqvision camera license to the camera s server on the System Setup page. When complete, the status is displayed as Licensed. 12. On the IP Cameras page, verify that the camera is associated with its embedded server: The IP address must be so that the embedded server communicates with the local camera. The camera s credentials are root and admin by default. The status is displayed as Connected when complete. 13. See the exacqvision user manual for additional configuration steps, such as configuring recording settings. Page 4 of 7

5 Motion Detection/Serial Profile Configuration 1. In exacqvision Client, open the Serial Profiles page. 2. Click New to create a new profile. 3. For Profile Name, enter ISD Motion. 4. For SOT Marker, enter motion start. 5. For EOT Marker, enter motion stop. 6. Select the Case Sensitive checkbox. 7. Under Key Word, type start. Make sure the Enable checkbox is selected next to the entry. 8. Click Apply Page 5 of 7

6 Event Linking and Schedule Configuration 1. In exacqvision Client, open the Event Linking page. 2. Click New to create a new link. 3. Under Event Type, select Serial Profile. 4. Under Event Source, select ISD Motion 5. Under Action Type, select any desired action, such as Record Video, that you would like to automatically activate when the ISD Motion event occurs. 6. Under Action Target, select any camera, audio input, trigger, profile, or preset associated with the selected Action Type. 7. Open the Schedule page and configure an Alarm schedule for the serial profile Page 6 of 7

7 Troubleshooting If you encounter a write error, complete the following steps: 1. Stop the exacqvision Edge server on the camera s Applications page. 2. Unmount the SD card on the Storage Setup page. 3. Check the SD card. If necessary, repair and format the card. 4. Remount the SD card. 5. Restart the exacqvision Edge server on the camera s Applications page. Page 7 of 7

exacqvision Edge/Axis Quick Start Guide

exacqvision Edge/Axis Quick Start Guide Introduction exacqvision Edge is a variation of the standard exacqvision Server application that operates on a compatible Axis camera. It can record video from the