SCHNEIDER OPTICS INC. DISTAR PROJECTOR LENS W/ FOCUS MOUNT INSTRUCTION MANUAL
|
|
- Rachel Strickland
- 6 years ago
- Views:
Transcription
1 SCHNEIDER OPTICS INC. DISTAR PROJECTOR LENS W/ FOCUS MOUNT INSTRUCTION MANUAL Page
2 INTRODUCTION Thank you for purchasing the Schneider Optics DiStar+HD projector lens. With the Schneider DiStar focus mount, the lens is designed to function with Barco, Christie, and NEC projectors and gives the end user the ability to adjust the focus. Please read the following instructions before proceeding to install the DiStar+HD lens to the projector. By factory default, the DiStar+HD lens is configured with a full aperture iris. An optional cats-eye iris is available for use with your lens. Please contact Schneider Optics Inc. for order information. TABLE OF CONTENTS Barco projector use...page 3 NEC projector use...page 4 Christie projector use...page 6 PART NUMBER XXX Parts List DESCRIPTION BRACKET, DISTAR, BARCO ADAPTER, CHRISTIE, FOCUS MOUNT XX mm DISTAR LENS WITH FOCUS MOUNT SCREW, M4X8, SOC, CAP, SS, BO WASHER, M4, SPLIT, STEEL, BO WASHER, M4, ROUND, SS, BO SCREW, SET, 0-32 X /8, CUP POINT, SOC, STEEL, BO HEX DRIVER /8" HEX DRIVER, 3/32" HEX DRIVER, 3MM HEX DRIVER, /6" SCREW, SET, 6-32 X /8, NYLON TIP, SOC SS QTY REQUIRED TOOLS -/8' Hex driver (provided) -3/32" Hex driver (provided) -/6" Hex driver (provided) -3 mm Hex driver (provided) Page 2
3 2X M4 SOCKET CAP SCREWS 2X M4 LOCK WASHERS SUPPORT BRACKET 2X M4 FLAT WASHER 3X /4-20 FOCUS LOCK BARCO PROJECTOR MOUNT PLATE FOCUS FLANGE ALIGNMENT PIN CLEARANCE SLOTS FIGURE BARCO PROJECTOR USE NOTE: By factory default, the DiStar projector lens is configured for use with a BARCO projector. Perform the following steps in order to mount your projector lens. Attach lens to projector per Barco instructions. Make certain that any one of the focus flange alignment pin clearance slots is aligned with the projector alignment pin. NOTE: Multiple alignment pin clearance slots are provided in order to accomidate the use of a cats-eye aperture iris. NOTE: Due to the weight of some DiStar lenses, provide temporary external support before proceeding to next step. 2. Attach support bracket to focus flange and Barco projector mount plate using the provided 3mm hex driver, M4 cap screws, and washers per Figure. 3. Once lens is securely attached to projector, loosen the 3- /4-20 focus lock set screws in order to allow the lens to rotate freely. Achieve focus by rotating lens clockwise / counterclockwise until lens is focused. Re-tighten focus lock set screws once focus is achieved. Page 3
4 5X /4-20 NYLON TIP BARCO PROJECTOR ADAPTER RING FIGURE 2 NEC PROJECTOR USE NOTE: By factory default, the DiStar projector lens is configured for use with a BARCO projector. Perform the following steps in order to mount your projector lens. Remove the 5- /4-20 X 3/6" nylon tip set screws from the Barco projector adapter ring by using the provided /8" hex driver. 2. Remove the Barco projector adapter ring by slipping the ring through back of lens as shown in Figure 2. Page 4
5 NEC PROJECTOR CLAMP 3X /4-20 FOCUS LOCK 2X PROJECTOR CLAMP THUMB SCREWS FIGURE 3 NEC PROJECTOR USE (Cont.) 3. Attach lens to projector per NEC instructions. Make certain that flange clearance cuts are aligned with projector clamp thumb screws for proper installation. 4. Once lens is securely attached to projector, loosen the 3- /4-20 focus lock set screws in order to allow the lens to rotate freely. Achieve focus by rotating lens clockwise / counterclockwise until lens is focused. Re-tighten focus lock set screws once focus is achieved. Page 5
6 5X /4-20 X 3/6 NYLON TIP BARCO PROJECTOR ADAPTER RING FIGURE 4 CHRISTIE PROJECTOR USE NOTE: By factory default, the DiStar projector lens is configured for use with a BARCO projector. Perform the following steps in order to mount your projector lens. Remove the 5- /4-20 X 3/6" nylon tip set screws from the Barco projector adapter ring by using the provided /8" hex driver. 2. Remove the Barco projector adapter ring by slipping the ring through back of lens as shown in Figure 4.. Page 6
7 FOCUS FLANGE ASSEMBLY FOCUS BODY FOCUS FLANGE ASSEMBLY 3X /4-20 FOCUS LOCK FIGURE 5 FOCUS FLANGE FIGURE 7 FIGURE 6 CHRISTIE PROJECTOR USE (Cont.) 3. Using the provided /8" hex driver, remove the 3- /4-20 focus lock set screws in order to allow the focus flange assembly to rotate freely per Figure Rotate the focus flange assembly in a counter clockwise direction in order to remove it from the lens per Figure Separate components on focus flange assembly, (focus flange and focus body), by unscrewing the two components from each other per Figure 7. NOTE: Separating focus flange from focus body may be difficult due to the presence of thread adhesive. If necessary, heat components up in order to aid in separation. Page 7
8 CHRISTIE ADAPTER RING 5X 0-32 X /8 3.0mm 3X 6-32 X /8 NYLON TIP FOCUS BODY CLOCKWISE FIGURE 8 B FIGURE 8 A CHRISTIE PROJECTOR USE (Cont.) 6. Re-install the focus body back on to the lens. Rotate the focus body in a clockwise direction until it completely bottoms out and reverse 4 complete rotations. When step 8 is completed, confirm that the gap as shown in Figure 8B is approximately 3 mm. 7. Using the provided /6" hex driver, attach X /8 nylon tip set screws in order to lock focus body in place. 8. Attach Christie projector adapter ring by slipping ring through back of lens until ring bottoms out on lens neck as shown in Figure 8 B. Secure the adapter ring by using the provided 3/32" hex driver and the X /8" set screws. Page 8
9 CHRISTIE PROJECTOR LOCATION PINS CHRISTIE PROJECTOR MOUNT PLATE FIGURE 9 CHRISTIE PROJECTOR USE (Cont.) 9. Attach lens to projector per Christie instructions. 0. Once lens is securely attached to projector, use projector focusing capabilities in order to focus lens.. If focusing can not be achieved with projector focusing capabilities, the DiStar lens has built-in focusing capabilities. Remove lens from projector and loosen the X /8 nylon tip set screws as indicated in step 7. Insert the lens back into the projector and clamp. Rotate the lens to achieve focus. Once focus is achieved, remove lens and tighten the X /8 nylon tip set screws. Page 9
Ultra short throw lens installation
Ultra short throw lens installation The ultra short throw lens 0.36 UST GS (P/N: 140-133108-XX) allows you to position your projector as close as possible to your screen or display. Unless otherwise indicated,
More informationIf you are missing any of the following items, please contact Stanton Video immediately (602)
RIGHT ANGLE FOCUS Jan 03 If you are missing any of the following items, please contact Stanton Video immediately (602) 493-9505 1. Right Angle Focus Servo 2. Servo End Cap 3. Lens Gears (32 pitch, 48 pitch,.6
More informationIn-Sight 7000 Series Vision System. Optional Configurations
In-Sight 7000 Series Vision System Optional Configurations Legal Notices The software described in this document is furnished under license, and may be used or copied only in accordance with the terms
More informationInstallation and Assembly: 2 x 2 Video Wall Ceiling Mount for 40" - 55" flat Panel Displays
Installation and Assembly: 2 x 2 Video Wall Ceiling Mount for 40" - 55" flat Panel Displays Model: DS-VWT955-2X2 EXTENSION COLUMN (SOLD SEPARATELY) COMPATIBILITY Display width must be a minimum of 36"
More informationLENS ATTACHMENT KIT INSTALLATION GUIDE
XM2 and XMU LENS ATTACHMENT KIT INSTALLATION GUIDE for Paladin and Phoenix lenses The XM2 Plate system attaches directly to many Epson, JVC and Sony home theater projectors OR it can be sandwiched between
More informationBPL SERIES INSTALLATION INSTRUCTIONS THIS SHEET CONTAINS IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS.
BPL SERIES INSTALLATION INSTRUCTIONS Important Warning THIS SHEET CONTAINS IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS. This product must be installed in accordance with National Electrical
More informationPeel/Rewind Upgrade Kit
Peel/Rewind Upgrade Kit Installation Instructions This kit includes the parts and documentation necessary to install the Peel/Rewind upgrade kit on the following printers: ZM400 ZM600 Read these instructions
More informationM40 Microscope User s Manual
M40 Microscope User s Manual for M40 and M40RT Microscope Components: Trinocular Port Eyepieces Beam Splitter Field Diaphragm Adjustment Aperture Diaphragm Adjustment Filter Slots Analyzer Polarizer Hex
More informationGCX Mounting Assembly Installation Guide. Pedestal Mount for Philips IntelliVue MP5/20/30/40/50/60/70, MX400/450/500/550/600/700/800
3875 Cypress Drive Petaluma, CA 94954 800.228.2555 707.773.1100 Fax 707.773.1180 www.gcx.com GCX Mounting Assembly Installation Guide Pedestal Mount for Philips IntelliVue MP5/20/30/40/50/60/70, MX400/450/500/550/600/700/800
More informationCLIMB2 DUAL MONITOR SIT/STAND WORKSTATION
CLIMB2 DUAL MONITOR SIT/STAND WORKSTATION CLIMB2 Rev A 3/17 Model CLIMB2-SLV ASSEMBLY AND ADJUSTMENT CLIMB2 PARTS AND TOOLS PLEASE REVIEW these instructions before beginning the assembly and adjustment
More informationTEC APO 200 OWNER S MANUAL
TEC APO 200 OWNER S MANUAL 2005 IMPORTANT - PLEASE READ THIS MANUAL BEFORE USING YOUR TELESCOPE SAFETY WARNINGS Do not look at the sun through the telescope! Viewing the sun through the telescope without
More informationInstallation Guide Mounting Kit for Mounting Philips Avalon CTS Cordless Fetal Transducer System on Wall, 2'' Post, Rail, or Slide-on Mounting Plate
Installation Guide Mounting Kit for Mounting Philips Avalon CTS Cordless Fetal Transducer System on Wall, 2'' Post, Rail, or Slide-on Mounting Plate The purpose of this guide is to: 1. Describe mounting
More informationVacuum Maintenance Manual (EXCERPT Tim Benedict)
1. Position a ladder, scaffold, or work stand, on the right side of Vacuum Skid where the blower motors are installed. 2. Locate the six (6) vacuum hoses connecting the blower motors to the HEPA housings
More informationMac Mini Mid 2011 SSD Installation
Mac Mini Mid 2011 SSD Installation Replace your Mac Mini Mid 2011's hard drive for more storage space and an increase in speed. Written By: Dozuki System 2017 guides.crucial.com Page 1 of 14 INTRODUCTION
More informationLNS-S10/LNS-T10/LNS-W10/LNS-T11/LNS-W11
LCD Projector Lens Replacement Procedure Model Number LNS-S10/LNS-T10/LNS-W10/LNS-T11/LNS-W11 Notes on Lens Replacement Lens replacement should be performed by the qualified service personnel. It should
More informationFurther Information can be found at
Below is a step by step guide to assembling the Hurricane-Rig. Remember that this is a precision optical instrument. Excessive force can bend critical parts. If treated well it should give many years of
More informationNext Gen Sarix Enhanced IBE Series Bullet Cameras
Next Gen Sarix Enhanced IBE Series Bullet Cameras Installation Manual C1334M 12/16 1 Contents Important Notices... 3 Regulatory Notices... 3 Radio and Television Interference... 3 Korean Class A EMC...
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS 19 20 21 01 07 22 23 13 10 12 08 17 18 11 02 14 15 04 03 16 WELCOME PARTS LIST Thank you for purchasing this HealthPoint Technology Cabinet from Humanscale! Before you begin installing
More informationMac Mini Mid 2011 SSD Dual Drive Installation
Mac Mini Mid 2011 SSD Dual Drive Installation Install a second hard drive in your mid 2011 Mac Mini. Written By: Dozuki System 2017 guides.crucial.com Page 1 of 19 INTRODUCTION Use this guide to install
More informationM20 Metallurgical Microscope User s Manual. Fein.
M20 Metallurgical Microscope User s Manual info@feinoptic.com M20 Microscope Components Lamp Housing C-Mount Adapter Eyepieces Analyzer Objective Lens Coarse Focus Mechanical Stage Stage X-Y Control Fine
More informationInstallation Guide Roll Stand Kit for Philips Avalon FM20/30
3875 Cypress Drive Petaluma, CA 94954 800.228.2555 707.773.1100 Fax 707.773.1180 www.gcx.com Installation Guide Roll Stand Kit for Philips Avalon FM20/30 The purpose of this guide is to: 1. Describe attachment
More informationNAV-1 Lens Support. NAV-2 Lens Support BEFORE YOU BEGIN
INSTALLATION Lens Support INSTRUCTIONS The Lens Support is compatible with any RPA projector mount. The readily adapts to the following ScreenStar Conversion Lens from Navitar: SSW08 and SST120. LENS SUPPORT
More informationBE Series. Dual Action Ballhead. You re on steady ground
BE Series Dual Action Ballhead You re on steady ground 1 Introduction Thank You for choosing Oben! This sturdy Oben BE Series Dual-Action ballhead provides smooth, effortless operation. Two locks provide
More informationMac mini Mid 2010 IR Sensor Replacement
Replace a broken IR sensor/sleep LED. Written By: Andrew Bookholt ifixit CC BY-NC-SA www.ifixit.com Page 1 of 18 INTRODUCTION Use this guide to replace your mini's IR sensor/sleep LED assembly. Replacing
More informationMK-212 SERIES PARTS LIST MODELS: MK Part # MK SPCL Part # SPCL MK Part #
www.mkdiamond.com MK-1 SERIES PARTS LIST MODELS: MK-1- Part # 191 MK-1--SPCL Part # 191-SPCL MK-1-6 Part # 16 MK-1- Part # 191 MK-1-6 Part # 16 Revision 100 1.016 Manual Part No. 196-PM Caution: Read all
More informationMi50 Inverted Microscope User s Manual. Fein.
Mi50 Inverted Microscope User s Manual Fein info@feinoptic.com Mi50 Microscope Components Siedentopf Trinocular Head Stage Plate Mechanical Stage Locking Screw Hex Wrench Storage Beam Splitter Dust Protector
More informationJIB EPT USER MANUAL. Please read this manual carefully before using the Alphatron JIB ETP unit! JIB & MOTORISED PAN AND TILT UNIT
JIB EPT JIB & MOTORISED PAN AND TILT UNIT USER MANUAL EN Please read this manual carefully before using the Alphatron JIB ETP unit! Thank you for purchasing a Alphatron product The EPT head is developed
More informationMac Mini Mid 2010 SSD Installation
Mac Mini Mid 2010 SSD Installation Replace your Mac Mini Mid 2010's hard drive for more storage space and an increase in speed. Written By: Dozuki System 2017 guides.crucial.com Page 1 of 15 INTRODUCTION
More informationMBX INSTRUCTION MANUAL. Please read this manual carefully before using the MBX! Mid-range studio stand
MBX Mid-range studio stand INSTRUCTION MANUAL EN Please read this manual carefully before using the MBX! CAMBO Thank you for purchasing a Cambo product. This new classed Mid-range studio stand will suit
More informationMD-BSL15W / SPRING-LOADED TWIN-ARM. For ( cm) LCD desktop computer. User Manual
MD-BSL15W / SPRING-LOADED TWIN-ARM MONITOR mount For 15 27 (38.1 68.6 cm) LCD desktop computer User Manual Thank you for choosing Gabor. The Gabor MD-BSL15W mounts two 15 27 (38.1 68.6 cm) LCD computer
More informationUniversal Desktop and Monitor Stand
Universal Desktop and Monitor Stand Installation Instructions Kit P/N: 114-6013 Kit Contents Kit Contents: (1) Stand Assembly (1) VESA Monitor Bracket (1) Bottom Bracket (1) Top Bracket (1) Clamp Bracket
More informationATTENTION: OBSERVE PRECAUTIONS FOR HANDLING ESD-SENSITIVE DEVICES
15 Monitor Removal 1. Turn off and unplug the game. 2. Place something in front of the game to brace the bezel once the strain relief cord is undone, then unlock and open the CPU section. 3. Remove the
More informationSpacebar. Modular Microphone Positioning System. User Manual, Revision C, August, Spacebar Modular System User Manual Revision C Page 1 of 29
Spacebar Modular Microphone Positioning System User Manual, Revision C, August, 010 Spacebar Modular System User Manual Revision C Page 1 of 9 Table of Contents Standard pre-configured arrays:... 4 SB-SUR
More informationZero Gravity Rig Operating Instructions
Welcome to our new top-of-the-line shoulder support system for cameras up to 15 lbs - the ZG Rig. In addition to its totally unique vertical balancing mechanism, this system is designed to be configurable
More informationFlowPod Stabilizer / MonoPod / Low Mode
FlowPod Stabilizer / MonoPod / Low Mode FlowPod Operating Manual Thank you for purchasing the versatile FlowPod, our patented stabilizer/support. The FlowPod offers several shooting options that will help
More informationMicro Tech Lab. Operating Instruction LM DSLR Photomicroscope. Depending on the microscope configuration
Micro Tech Lab www.lmscope.com Operating Instruction LM DSLR Photomicroscope Depending on the microscope configuration and shipping country, the LM Photomicroscope is delivered with attached base plate
More informationSno-Thro. Parts Manual. Models (SS522EC) (SS722EC) (SS522) (SS522EC) (SS722C) /06 Printed in USA
Sno-Thro Parts Manual Models 801 (SSEC) 8018 (SSEC) 801 (SS) 8 (SSEC) 80 (SSC) 0000 /0 Printed in USA THE MANUAL Before you operate your unit, carefully and completely read manuals supplied with the unit.
More informationACCELERATOR LENS ADAPTER
ACCELERATOR LENS ADAPTER User Manual LAG-MFT-NF Nikon F-Mount to Micro Four Thirds THANK YOU FOR CHOOSING VELLO The Vello Accelerator Lens Adapter is for attaching Nikon F-Mount lenses to Micro Four Thirds
More informationMK-101 TILE SAW OWNER S MANUAL & OPERATING INSTRUCTIONS SERIAL NUMBER:
MK-0 TILE SAW OWNER S MANUAL & OPERATING INSTRUCTIONS CAUTION: Read all safety and operating instructions before using this equipment Enter the Serial Number of your new saw in the space below. The Serial
More informationMac mini Mid 2011 Heat Sink Replacement
Mac mini Mid 2011 Heat Sink Replacement Replacing the mini's heat sink. Written By: Walter Galan ifixit CC BY-NC-SA www.ifixit.com Page 1 of 16 INTRODUCTION Use this guide to replace your mini's heat sink.
More informationUltima X5000 Round Duct Mount Kit User Instructions
Ultima X5000 Round Duct Mount Kit User Instructions MSA Kit 10179124/10179321 - Ultima X5000 316 Stainless Steel Parts List / Instructions Round Duct Mount Gasket (1) Round Duct Mount Base Plate (1) Base
More informationMAGIXBOX TM. Quick Start Guide
TM TM by TouchMagix MAGIXBOX TM Quick Start Guide What s in the box: Ankle Ceiling Plate Extendable Rod Connector Piece Middle Piece Universal Spider Super clamp with ball socket Safety Cable Projector
More informationCutter Option Installation Instructions
This kit includes the parts and documentation necessary to install the cutter option on the Zebra XiII, XiIII, and XiIIIPlus-Series printers. NOTE: The Cutter Option is not available for the 96XiIII. Adding
More informationHARDWARE KITS. Call in NY or Fax Outside the NY area, JCP. HARDWARE A F JCP
112 KITS 29601-000 10-229602-000 12-10 0166-015 12-100166-016 12-10 12-860331-A 0166-031 12-100166-032 12-15 230000-001 11-23001-001 11-23002-0 12-860331-B 12-860331-C 12-860331-D 12-860331-E 12-860331-F
More informationBC Series. Dual Action Ballhead. You re on steady ground
BC Series Dual Action Ballhead You re on steady ground 1 Introduction Thank You for choosing Oben! This sturdy Oben BC Series Dual-Action ballhead provides smooth, precise operation. Two locks provide
More informationMK-212 SERIES OWNERS MANUAL & OPERATING INSTRUCTIONS
www.mkdiamond.com MK-212 SERIES OWNERS MANUAL & OPERATING INSTRUCTIONS MK-212-4 MK-212-6 Revision 303 03.2012 Manual Part No. 159862 Caution: Read all safety and operating instructions before using this
More informationPlanar Model A480-PL Professional Grade Home Cinema Conversion Lens System
AKPro system with ATH1 transport shown Planar Model A480-PL Professional Grade Home Cinema Conversion Lens System USER MANUAL AND INSTALLATION GUIDE Including the UH480 Lens, ATH1 Transport and AKPro Projector
More informationAssembling the Christie QwikRig rigging frame
ssembling the hristie QwikRig rigging frame With the hristie QwikRig rigging frame, the projector can be secured to trusses or structures built for the purpose of positioning the projector. With the frame:
More informationMain Menu. Menu II. UNPACKING AND SETUP II-5. RADF MR-3021/3022
PRECAUTIONS UNPACKING ACCESSORIES SETUP CLEARANCE ADJUSTMENT OPERATION CHECK SKEW ADJUSTMENT LEADING EDGE POSITION ADJUSTMENT HORIZONTAL POSITION ADJUSTMENT COPY RATIO ADJUSTMENT There is no difference
More informationMac mini Mid 2011 Hard Drive Replacement
Replace your Mac mini's Mid 2011 hard drive for more storage space. Written By: Walter Galan ifixit CC BY-NC-SA www.ifixit.com Page 1 of 15 INTRODUCTION Use this guide to completely replace your mini's
More informationUniversal Tablet Mount Accessory for Flex TechBridge
Assembly Instructions Universal Tablet Mount Accessory for Flex TechBridge Universal Tablet Mount Accessory Universal Tablet Mount Accessory mounted on Flex Arm CONTENTS Important User Information...........................2
More informationMicroscopic Imaging Research Station (MIRS) Assembly Guide. Version 1.0.0
Microscopic Imaging Research Station (MIRS) Assembly Guide www.adsyscontrols.com Adsys Controls, Inc.2012 Version 1.0.0 I. Assembly of the Adsys Controls MIRS system This document explains the assembly
More informationIS-DM220/IR/HB IS-DM220
IS-DM220/IR/HB IS-DM220 Installation Guide Indoor/Outdoor Ver. 1.2 00P6NX223ZXSEA2 Table of Contents 1. Indoor Camera Installation... 3 1.1 Hard Ceiling... 3 1.2 In-Ceiling (T-Bar) Mounting... 13 1.3 4S
More information3-Lamp Fluorescent Ring Light 19" INSTRUCTIONS
3-Lamp Fluorescent Ring Light 19" INSTRUCTIONS Introduction Thank you for choosing Impact. The Impact 3-Lamp Fluorescent Ring Light 19" is a continuous light for photography and video. It casts a soft,
More informationSit-Stand Monitor Arm
Sit-Stand Monitor Arm Product ID: ARMSTSCP1 This sit-stand monitor arm transforms your desk or tabletop into an ergonomic workstation. The monitor arm features a keyboard tray and easy height adjustment
More informationRichter Optica. Instructions for: S6-BL, S6-TS, S6-SPS, S6-ILST Models
Richter Optica info@richter-optica.com Instructions for: S6-BL, S6-TS, S6-SPS, S6-ILST Models Trinocular port for c-mount adapter Zoom Knob Focusing Holder Clamp Diopter adjustable eyepieces Magnification
More information110 manuals_110 manuals 6/27/2010 8:16 PM Page 1 TEC APO110 FL ECLIPSE
110 manuals_110 manuals 6/27/2010 8:16 PM Page 1 TEC APO110 FL ECLIPSE OWNER S MANUAL 2010 110 manuals_110 manuals 6/27/2010 8:16 PM Page 2 IMPORTANT - PLEASE READ THIS MANUAL BEFORE USING YOUR TELESCOPE
More informationTDM-100/150 TO NMD-50 CONVERSION PROCEDURES RL5000
TDM-00/50 TO NMD-50 CONVERSION PROCEDURES RL5000 TDN 0702-00062 March 7, 204 Corporate Headquarters 2405 B Street Long Beach, MS. 39560 Phone: (800) 259-6672 Fax: (228) 868-9445 COPYRIGHT NOTICE 204 Triton.
More informationService Parts Diagrams. For Model: 2000i-DVS with the NEC VT465 Projector 2000i-DVS with the NEC VT470 Projector
Service Parts Diagrams For Model: 000i-DVS with the NEC VT65 Projector 000i-DVS with the NEC VT70 Projector Service Parts Diagrams for the Rear Projection SMART Board 000i-DVS Interactive Whiteboard Identifying
More informationInstallation Guide GE Healthcare Solar 8000M Keypad Mounting Kit for 15'' and 18'' Flat Panel Displays
Installation Guide GE Healthcare Solar 8000M Keypad Mounting Kit for 15'' and 18'' Flat Panel Displays The purpose of this guide is to: 1. Describe attachment of Keypad to Keypad Mounting Bracket (page
More informationPrepare the Media for Loading
39 You can use roll media or fanfold media in your printer. Roll media hangs on and is loaded from the media supply hanger. Fanfold media is stored away from or in the bottom of the printer and can drape
More informationMac mini Mid 2011 IR Sensor Replacement
Replace a broken IR sensor/sleep LED. Written By: Walter Galan ifixit CC BY-NC-SA www.ifixit.com Page 1 of 19 INTRODUCTION Use this guide to replace your mini's IR sensor/sleep LED assembly. Replacing
More informationEVOLVE1-M MONITOR ARM
EVOLVE1-M MONITOR ARM EVOLVE1-M Rev A 2/17 Model EVOLVE1-M-SLV Model EVOLVE1-M-BLK Model EVOLVE1-M-WHT ASSEMBLY AND ADJUSTMENT EVOLVE1-M MONITOR ARM PARTS AND TOOLS PLEASE REVIEW these instructions before
More informationFLOE WIRELESS REMOTE ASSEMBLY INSTRUCTIONS KIT P/N
FLOE WIRELESS REMOTE ASSEMBLY INSTRUCTIONS KIT P/N 5-0083-00 TOOLS REQUIRED - 3/4" SOCKET - 3/4" WRENCH - /3" WRENCH - PHILLIPS SCREW DRIVER - TORQUE WRENCH INSTRUCTION P/N 6-0083-00 ISSUED: 3//7 SHEET
More informationASSEMBLY INSTRUCTIONS, ELO SELF SERVICE STAND
ASSEMBLY INSTRUCTIONS, ELO SELF SERVICE STAND E062324 ELO-STAND-SELF-SERVICE-DESKTOP E062510 ELO-STAND-SELF-SERVICE-FLOOR EXT E062704 KIT-EMV-CRADLE-VF-MX915-ING-ISC250 E062899 KIT-EMV-INGENICO IPP350
More informationInstallation Guide Philips MP20/30/40/50/60/70 IntelliVue M-Series Arm Rail Mount Kit
Installation Guide Philips MP20/30/40/50/60/70 IntelliVue M-Series Arm Rail Mount Kit The purpose of this guide is to: 1. Describe attachment of Table Top Mount to Mounting Adapter on Arm (page 2). 2.
More information3500 Series Tripod Kit
3500 Series Tripod Kit You re on steady ground 1 INTRODUCTION Thank You for choosing Oben! This versatile and durable Oben tripod and ballhead is a compact and lightweight kit that sets up quickly, folds
More informationMK-MANTA I. Model MK-Manta I Core Drill Owner s Manual Parts List & Operating Instructions. serial number CAUTION
please record the serial number of your drill in this block. serial number For your one (1) year warranty to be effective, complete the warranty card (include the serial number) and mail it in as soon
More information060-Hardware. Clamps and Brackets Hose Clamps
Hose Clamps Part No. Range 401-41904 7/32" - 5/8" 401-41906 7/16" - 25/32" 401-41908 1/2" - 29/32" 401-41910 9/16" - 1-1/16" 401-41912 11/16" - 1-1/4" 401-41916 13/16" - 1-1/2" 401-41920 13/16" - 1-3/4"
More informationService Parts Diagrams
Service Parts Diagrams For Model: 000i-DVX with the NEC MT00 Projector 000i-DVX with the NEC VT0 Projector 000i-DVX with the NEC VT70 Projector Service Parts Diagrams for the Rear Projection SMART Board
More informationSP-325, SP-575X, SP-1075X Single-Stage Tailgate Spreaders
September 15, 2014 Lit. No. 43827, Rev. 01 SP-325, SP-575X, SP-1075X Single-Stage Tailgate Spreaders Parts List This Parts List is for SnowEx single-stage tailgate spreaders with serial numbers 140502300135
More informationSetup Information Panosaurus May 3, 2011
Setup Information Panosaurus 2.0 www.gregwired.com May 3, 2011 Please take the time to read all of the setup information to ensure success and ease of use of this tripod head. Much of the setup is a one
More informationDUAL-ARM MONITOR MOUNT For in. ( cm) desktop computer monitors
LeviTouch DM-502 DUAL-ARM MONITOR MOUNT For 15 27 in. (38.1 68.6 cm) desktop computer monitors User Manual Thank you for choosing Gabor. The Gabor Dual-Arm Desktop Mount can securely support two monitors
More informationTitan Media Cart. Installation and Operation Manual
Titan Media Cart Installation and Operation Manual Table of Contents INTRODUCTION SERVICE AND SUPPORT... 1 PRODUCT RETURNS... 1 UNPACKING... 1 TITAN SINGLE MEDIA CART... 2 TITAN DUAL MEDIA CART... 2 BEFORE
More informationLS-785 High Throughput Lens Spectrograph User Manual
15 Discovery Way, Acton, MA 01720 Phone: (978)263-3584, Fax: (978)263-5086 Web Site: www.piacton.com LS-785 High Throughput Lens Spectrograph User Manual Ver. 1.2 Table of Contents Chapter 1 -- General...5
More informationCONSOLE CONNECTOR KIT 9501 INSTALLATION INSTRUCTIONS
CONSOLE CONNECTOR KIT 9501 INSTALLATION INSTRUCTIONS FOR USE WITH: HAMMOND Organ Models L-100, M-100 Series, M-l, M-2, M-3 LESLIE Speaker Models 760, 770, 825 KIT CONTENT Console Connector Assembly 043075
More informationCTT Section Carbon-Fiber Tabletop Tripod. You re on steady ground 1
CTT-1000 3-Section Carbon-Fiber Tabletop Tripod You re on steady ground 1 INTRODUCTION Thank you for choosing Oben! The Oben CTT tripod is a sturdy and high-quality carbon-fiber tabletop tripod that provides
More informationSERVICE PARTS MANUAL
SERVICE PARTS MANUAL V-BOX SPREADER POLY DUAL ELECTRIC MODEL PDE00 - / CUBIC YARD MODEL PDE00 - / CUBIC YARD MODEL PDE800 - CUBIC YARD SPREADERS WITH SERIAL NUMBERS AFTER: PDE0000, PDE0000, 8PDE0000 CHUTES
More informationCaution Observe proper electrostatic safety precautions when handling any static-sensitive components such as circuit boards and printheads.
HFWLRQ HFWLRQ *HQHUDO,QIRUPDWLRQ Use the mechanical assembly drawings when troubleshooting or replacing components and use the associated parts list when ordering replacement parts. Item parts that do
More informationFormulate 20 Vertical Curve
Formulate 20 Vertical Curve FMLT-WV20-03 Formulate TM is a collection of sophisticated, ergonomically designed exhibit booths. Formulate combines state-of-the-art zipper pillowcase dye-sublimated fabric
More informationWritten By: Walter Galan
imac Intel 21.5" EMC 2428 CPU Replacement Replace the CPU in your imac Intel 21.5" EMC 2428. Written By: Walter Galan ifixit CC BY-NC-SA www.ifixit.com Page 1 of 33 INTRODUCTION Use this guide to upgrade
More informationCypLite Fiber Laser Cutting Head User Manual
1 CypLite Fiber Laser Cutting Head CypLite Fiber Laser Cutting Head User Manual www.fscut.com Ver 1.5.4 Thank you for using our products! This Manual describes CypLite fiber laser cutting head in details,
More informationGH-30. Gimbal Head. You re on steady ground
GH-30 Gimbal Head You re on steady ground 1 INTRODUCTION Thank You for choosing Oben! The Oben GH-30 is a gimbal-type tripod head designed to balance a lens along its vertical and horizontal axes. The
More informationWarning Before Installation
English Warning Before Installation Power off the Network Camera as soon as smoke or unusual odors are detected. Keep the Network Camera away from water. If the Network Camera becomes wet, power off immediately.
More informationParts and Service Manual IMCO
XXTREME ADVANTAGE Gimbal Parts and Service Manual IMCO 510 East Arrow Highway San Dimas, CA 91773 (800) 899-8058 (909) 592-6162 Fax (909) 592-6052 www.imcomarine.com email info@imcomarine.com TABLE OF
More informationQ2 XBee Handheld Controller Assembly Guide
Q2 XBee Handheld Controller Assembly Guide Copyright Quantum Robotics Inc. Q2 Controller V1.0 1 Parts List: The kit comes with 14 individual bags. 1. Case Top and Bottom 2. Case Screw Package containing:
More informationTransit Color Light Signal. (6-3/8 Outer Lens Diameter)
645 Russell Street Batesburg, SC 29006 Service Manual 7080 Transit Color Light Signal (6-3/8 Outer Lens Diameter) Installation, Operation and Maintenance November, 997 997, Union Switch & Signal Inc. Printed
More informationPhase One. ixu-rs 1000 / ixu 1000 / ixu 150 UAV Camera Systems. For DJI M600 & M600 PRO. Installation Guide
Phase One ixu-rs 1000 / ixu 1000 / ixu 150 UAV Camera Systems Installation Guide For DJI M600 & M600 PRO 1 Phase One ixu-rs 1000 / ixu 1000 / ixu 150 UAV Camera Systems Installation Guide For DJI M600
More informationHusqvarna X2000E. Illustrated Parts List ConstructionParts.com ConstructionParts.com. ConstructionParts.
Husqvarna X000E Illustrated Parts List -0 0 Jun 00 MAINFRAME ASSEMBLY 0 X000E 000 MAINFRAME ASSEMBLY, X000 000 SHSB, / x / 00 SHAFT, ARBOR LOCK 00 FRAME, ROLL CAGE, X000 0 COVER, BELT GUARD 00 COVER, BELT
More informationTubeMount system. Section 11 (pp.53-59) Breadboards and bases. Section 12 (pp.60-62) Stages and rod system. Section 13 (pp.63-70)
OPTOMECHANICS - introduction 5 Optomechanics - introduction There are basically two ways of mounting an optical system enclosed or open. Enclosed systems,such as an ordinary microscope,are light- and dust-tight,rigid,
More informationNikon Focus Drive Manual
Nikon Focus Drive Manual PRIOR SCIENTIFIC INC., 80 RESERVOIR PARK DRIVE, ROCKLAND, MA 02370-1062 TELEPHONE 781-878-8442 FAX 781-878-8736 WWW.PRIOR.COM Table of Contents Safety Information...1 Unpacking
More informationATTENTION: OBSERVE PRECAUTIONS FOR HANDLING ESD-SENSITIVE DEVICES
Hard Drive Removal IMPORTANT NOTE: If you are replacing a PATA hard drive with a SATA hard drive, please see PATA to SATA Hard Drive Conversion. Hard Drive Identification: To determine whether your hard
More informationINSTRUCTION MANUAL EN
CS-CHRONOS HDSLR/DV SUPPORT SYSTEMS INSTRUCTION MANUAL EN Please read this manual carefully before using the Cambo CS rig! CAMBO WHERE TRADITION MEETS VISION MADE IN THE NETHERLANDS Thank you for purchasing
More informationInstallation Guide. Retrofit Kit for USB Ready Intraoral Systems
Installation Guide Retrofit Kit for USB Ready Intraoral Systems Table of Contents Wall-Mount Retrofit Kit... 2 Introduction... 2 Connecting the Articulating and Horizontal Arm Cables... 2 Installing the
More informationSTEP-BY-STEP INSTRUCTIONS FOR BUILDING A MICHELSON INTERFEROMETER. TECHSPEC Optical Cage System
STEP-BY-STEP INSTRUCTIONS FOR BUILDING A MICHELSON INTERFEROMETER TECHSPEC Optical Cage System INTRODUCTION 2 What is a Michelson Interferometer? A Michelson Interferometer is a simple interferometric
More informationGH-50. Gimbal Head. You re on steady ground
GH-50 Gimbal Head You re on steady ground 1 INTRODUCTION Thank You for choosing Oben! The Oben GH-50 is a gimbal-type tripod head designed to balance a lens along its vertical and horizontal axes. Ideal
More informationFantasea Blue Ray Tray (Cat. No. 2040, 2045, 2050) Instruction Manual
Fantasea Blue Ray Tray (Cat. No. 2040, 2045, 2050) Instruction Manual For Illustration- Blue Ray Double Tray with Housing 1 The Fantasea Blue Ray Tray allows integrating different components in an underwater
More information8100, 8200, , 8202, 8203, 8204, 8205, 8206
800, 8200, 8300 820, 8202, 8203, 8204, 8205, 8206 W R A, O USA T: 800 32 7950 440 998 2788 F: 440 992 2925... 023208 2 INSTRUCTIONS FOR 3/4,, -/4 DIAMETER TAPS FIGURE A B C D E F G HOT TAP SPINDLE HOT
More informationHeat Containment System (HCS)
Heat Containment System (HCS) Revision Number 1 Wright Line LLC 160 Gold Star Boulevard Worcester, MA 01606 Tel: 800-225-7348 508-852-4300 Fax: 508-365-6178 www.wrightline.com info@wrightline.com All products
More informationG500 SERIES MICROSCOPE OPERATION MANUAL For use with MFR# G502, G502T, G504, G504T, G505, G505T.
G500 SERIES MICROSCOPE OPERATION MANUAL For use with MFR# G502, G502T, G504, G504T, G505, G505T. United Products & Instruments, Inc. 182 Ridge Road, Suite E Dayton, NJ 08810 USA T. 732 274 1155; F. 732
More information