CHSM2210-B CHSM2211-B Medium Camera Housing with Integrated Bracket

Transcription

1 CHSM2210-B CHSM2211-B Medium Camera Housing with Integrated Bracket Installation Guide Building Technologies Fire Safety & Security Products

2 Data and design subject to change without notice. / Supply subject to availability Copyright by We reserve all rights in this document and in the subject thereof. By acceptance of the document the recipient acknowledges these rights and undertakes not to publish the document nor the subject thereof in full or in part, nor to make them available to any third party without our prior express written authorization, nor to use it for any purpose other than for which it was delivered to him.

3 Contents 1 Safety Target group General safety precautions Meaning of the signal words Meaning of the hazard symbols EU Directives Technical data Specifications Mechanical dimensions Key to parts Package contents Installation Accessing the inside of the housing enclosure Fitting the accessories Power supply modules Ceiling mount bracket Fitting the camera and lens Mounting the camera housing assembly Connecting to the power supply Adjusting the sunshield Maintenance and service Disposal

4

5 Safety 1 Safety 1.1 Target group The instructions in this document are designed only for the following target group. Target readers Qualification Activity Condition of the product Installer Technical training for building or electrical installations. Installs the product, individual components of the product or replacement parts. Components of the product are not yet installed or need to be replaced or modified. 1.2 General safety precautions Read the general safety precautions before operating the device. Follow all warnings and instructions marked on the device. Keep this document for reference. Always pass this document on together with the product. Please also take into account any additional country-specific, local safety standards or regulations concerning project planning, operation and disposal of the product. It is recommended that all preparatory work (e.g. fitting of accessories) be carried out in a workshop prior to final installation. Liability claim Do not connect the device if it is damaged or any parts are missing. Do not make any changes or modifications to the device unless they are expressly mentioned in this manual and have been approved by the manufacturer. Use only spare parts and accessories that have been approved by the manufacturer. Risk of failure due to incorrect installation The fuse for the device and the fuse for the electrical system of the building must be installed separately. Risk of cable damage due to stress Use only cable types that are approved for the environmental requirements. The cable glands used must be appropriate for the cable diameter. 5

6 Safety 1.3 Meaning of the signal words The severity of a hazard is indicated by the following written warning notices. Signal word CAUTION IMPORTANT Type of risk There is a risk of minor to medium injuries or damage to property Malfunctioning may result 1.4 Meaning of the hazard symbols The nature of the hazard is indicated by icons. Warning of a hazard 6

7 EU Directives 2 EU Directives The product complies with the requirements of the following EU directives. The EU declaration of conformity is available from: Fire & Security Products GmbH & Co. ohg Karlsruhe Germany European Directive 2004/108/EC Electromagnetic Compatibility Compliance with the European Directive 2004/108/EC has been proven by testing according to the following standards: Emitted interference: EN EN EN Class B Resistance to interference: EN European Directive 2006/95/EC Low-Voltage Directive Compliance with the European Directive 2006/95/EC has been proven by testing according to the following standard: Safety: EN

8 Technical data 3 Technical data 3.1 Specifications Nominal Voltage CHSM2210-B: V AC 50/60 Hz CHSM2211-B: V AC 50/60 Hz Fuse Rating (Fuse F1) CHSM2210-B: 2 A 250 V AC 5 x 20 Type (T), HBC CHSM2211-B: 5 A 250 V AC 5 x 20 Type (T), HBC Electrical Connections Main supply connections via fused PCB mounted terminal blocks. Use crimped ferrules when terminating cables. 6 way pillar terminal block available for user connections. Cable Entry 2 x 16 mm Cable Glands (5 10 mm diameter cable range) Heater 7 W nominal, 25 W max. PTC resistor heating element, thermostatically controlled. Environmental Operating Temperature -20 to +60 C Ensure fitted equipment has suitable temperature range for the application (e.g. maximum typical ambient operating temperature of camera and lens. Ta = 40 C). Maximum internal dissipated power Relative humidity 30 W Up to 95 % non-condensing Ingress Protection IP66 BS EN Material Finish Internal Dimensions (L x W x H) Weight Toughened Glass Window Aluminium extrusions (Housing body / Sunshield) Die cast aluminium (front and rear end caps/bracket) Endcaps: Polyester powder coat, RAL7016 Grey Housing Body: Polyester powder coat, RAL9006 White Aluminium Sunshield: Polyester powder coat, RAL9006 White Aluminium 300 x 85 x 85 mm 3.5 Kg 8

9 Technical data 3.2 Mechanical dimensions Fig. 1 Mechanical dimensions 1 Diameter 133 mm mm mm mm without tilt mm mm 5 76 mm mm 6 66 mm mm mm mm without tilt mm mm mm mm 9

10 Technical data 3.3 Key to parts Fig. 2 Key to Parts 1 Front End Cap 2 Housing Body 3 Sunshield 4 Rear End Cap 5 Cable Glands 6 Terminal Board 7 Camera Mounting Plate 8 Demister Assembly 9 Window 10 Bracket Assembly 10

11 Package contents 4 Package contents Camera housing assembly Installation Guide Camera fixing screw (1/4 BSW x ½ hex hd.) Camera fixing screw (1/4 BSW x ¾ hex hd.) Spacer block (1.6 mm thick) Spacer block (3 mm thick) 2.5 mm (across flats) ALLEN Key, long reach. 6 mm (across flats) ALLEN Key. Camera plate insulator Shoulder washer (to insulate screw from camera mounting plate) NOTE The complete assembly should be mounted and tested in the workshop prior to use on-site. Accessories Type CAPD1210-C230 CHBA-221X-B Designation 12 V DC 500 ma PSU 230 V AC input Ceiling Mount Bracket 11

12 Installation 5 Installation 5.1 Accessing the inside of the housing enclosure 1. Undo the two M4 captive screws that secure the housing cover to the rear cap/bracket assembly and slide the housing cover forward slightly. 2. Disconnect the earth wire from the termination board. 3. Slide the housing cover forward towards the front of the camera mounting plate, until it hinges downward (see Fig. 3). 4. If required, you can remove the housing cover from the camera mounting plate by twisting it slightly and withdrawing it from the hinge pins. NOTE To re-assemble carry out steps 1 to 4 in reverse, making sure the earth wire is reconnected. The two M4 screws which secure the housing to the rear cap should be retightened to a torque of 2 Nm. Fig. 3 Inside the housing enclosure 1 Sun Shield 2 Demister 3 Termination Board 4 Rear Cap 5 Camera Mounting Plate 6 Housing Cover 12

13 Installation 5.2 Fitting the accessories Power supply modules In some installations the camera requires a 12 V DC power supply; Siemens power supply module CAPD1210-C230 is available and mounts inside the rear end cap (see Fig. 4). It is fused by connecting it through the terminal board. To fit the module: 1. Secure the module in the rear end cap using two M3 screws and lock washers (see Fig. 4), taking care not to trap any cables. Fig. 4 Power supply module 1 12 V DC Power Supply Module 2 M3 Screws 2. Cut the module s input cables (brown/blue) to a suitable length and connect them to the termination board s Fused Output terminals (brown live; blue neutral). See section 5.5 for terminal board details. 3. Connect the module s output cable to the camera supply terminals after fitting the camera (White stripe or ribbed stripe positive, +12 V DC; black negative, 0 V.). Use suitable cable clips (not supplied, see Fig. 5). 13

14 Installation Fig. 5 Power supply module cable routing 1 12 V DC power supply module 2 Suitable cable clip (not supplied) 3 PSU module output cable to camera supply terminals 4 PSU module input cable 5 Fused output terminals IMPORTANT Ensure all SELV and signal wiring is kept away from live parts and is suitably protected from live parts by double insulation Ceiling mount bracket A ceiling mount bracket CHBA-221X-B is available for the housing which rotates the mounting surface by 90 degrees to allow mounting onto a ceiling. An installation instruction is supplied with the bracket. 14

15 Installation 5.3 Fitting the camera and lens The camera should be mounted so that the lens is aligned with the centre of the housing window and as close to the window as possible. 1. With the slots aligned, fit the self-adhesive camera plate insulator to the camera plate (see Fig. 6). 2. Position the camera at the required height by placing the appropriate spacer blocks between the mounting plate and the camera. Note that two thicknesses of spacer are supplied. 3. Place the supplied shoulder washer through the slot in the camera mounting plate from the bottom up, and then feed the mounting screw through the washer and spacer blocks and screw into the camera mounting. 4. Adjust the camera position before you fully tighten the mounting screw. 5. Connect power to the camera as described in Section Terminate and connect the necessary video signal cable to the camera (e.g. coax cable). Fig. 6 Fitting the camera and lens 1 Camera 2 Spacer block 3 Camera plate insulator 4 Adjustment location slot 5 Shoulder washer 6 Mounting screw (1/4 BSW) 1/2 or 3/4 15

16 Installation 5.4 Mounting the camera housing assembly The bracket has a set of 4 through holes suitable for M8 screws on a mm (4 ) PCD for mounting the assembly to a surface or bracket. The holes are part of a casting, and are 35 mm deep, which needs to be taken into account when specifying screw lengths. 1. Separate the three sections of the mounting bracketry by undoing the 2 x M6 Cap Head screws. 2. Remove the gland plate on the rear cap to allow ease of installation. Do this by loosening the bottom two screws in the plate, undoing the captive top screw and lifting out. 3. If required, drill and fit cable glands (28 mm maximum outside diameter) to the top or bottom of the wall or ceiling bracket section. Cables can be fed directly through the mounting surface into the bracketry. 4. Attach the wall bracket to the mounting surface using suitable fixings. A spirit level should be used to ensure that the fixing is level. IMPORTANT Ensure that the correct bracket for the application is used and that it is securely mounted to the prime surface. Ensure the surface to which the unit is being mounted is solid and that there is no risk of the bracket becoming loose due to crumbling brick or mortar. Ensure that all fixing screws are suitable for the application and securing bolts are tight. Where required fit suitable anti-vibration fastenings. 5. Feed the cables or conduit (16 mm maximum) through the wall bracket and centre section then attach the centre section to the wall bracket. Repeat this with the rear end-cap section. Secure but do not tighten the two M6 cap head screws which hold the sections of bracket together. Ensure that the toothed lock washers are still in place. 6. Feed the cables through the gland plate hole and refit the gland plate, passing the cables through the appropriate gland and tightening correctly to ensure a weatherproof seal. If conduit is used, replace the gland with the appropriate conduit fixing. 7. Before connecting the cable(s), move the housing through its full range of horizontal and vertical movement, mark the cable length at its greatest extremity. Cut the cable(s) at a suitable length to terminate. This will ensure that the cable is of sufficient length if the housing is repositioned at a later date. There must be no connection terminals within the mounting bracket. 8. Make sure that the cables are not snagged or trapped anywhere inside the mounting bracketry and that the cables were not damaged during the installation. 9. Connect the power input as detailed in section 5.5, terminate and connect any other cables as necessary (e.g. Coax cable to camera). 10. Move the camera housing to the required position and tighten the two M6 Cap Head screws to fix in position. It is important to ensure that the toothed lock washers are still in place after installation. 11. Refit the housing cover as described in section

17 Installation Fig. 7 Mounting the Camera Housing Assembly mm gland (for 5 10 mm diameter cables) 2 Rear end-cap section 3 Wall bracket section replace with ceiling mount option (CHBA-221X-B) if required 4 Sections are held together with 2 M6 screws and 2 x toothed lock washers 5 Centre section 6 Flat area top and bottom mm diameter through holes on a 4 (101.6 mm) PCD 17

18 Installation 5.5 Connecting to the power supply IMPORTANT Please read the Safety section on page 5 before connecting to the Power Supply. IMPORTANT Take care not to damage the cables during installation. All wiring must be installed to local and national standards. Ensure all SELV and signal wiring is kept away from live parts and is suitably protected from live parts by double insulation. CAUTION A readily accessible all-pole disconnect device with at least 3 mm contact separation shall be incorporated in the building installation wiring. As part of the building installation, protect the unit via a fuse or circuit breaker rated at 2 A for CHSM2210-B V AC units and 5 A for CHSM2211-B V AC units. NOTE Use only cable suitable for the application and that meets the standards required by the installation. The conductor size for power cable(s) must be at least 0.75 mm 2. The maximum recommended conductor size is 1.5 mm The two glands supplied are suitable for cables with a diameter of 5 10 mm; remove the blanking plug supplied in the chosen gland. It is important that the correct sized glands are used for the cable utilised to ensure a weatherproof seal. 2. Insert the power supply cable through the selected gland having fed it through the bracketry and cut to length as described in section Connect the power cable to the terminal board in the Input supply terminal indicated in Fig. 8, it is recommended to use crimp ferrules on the cores. 4. It is possible to move the terminal board assembly along the camera mount rail. Loosen the M3 screw and move the assembly, then retighten the screw. Indicator L N E Description Live (Brown) Neutral (Blue) Earth (Green/Yellow) Fig. 8 Terminal board connection details 1 Ancillary Connections Block 2 Fused Output 3 Earth (Gnd) 4 Input Supply Terminal 18

19 Installation 5 Fuse F1 2 A 250 V AC 5x20 Type (T), HBC for T462 (230 V AC) 5 A 250 V AC 5x20 Type (T), HBC for T463 (24 V AC) 6 Heater Output (pre-wired and connected through fuse F1) 5.6 Adjusting the sunshield 1. Firmly squeeze (A) the sides of the sunshield (see Fig. 9). 2. Slide (B) the sunshield to the required position. 3. Release the sunshield and it will remain in position. Fig. 9 Sunshield adjustment 19

20 Maintenance and service 6 Maintenance and service The following maintenance guidelines should be observed. Cleaning Use only soap and water to clean the housing and window no abrasive solvents. Additional protection can be applied to the window to reduce contamination and droplet formation from moisture or rain. Products from the automotive or cleaning industry which use nanotechnology to reduce surface energies and thus contamination and moisture build-up can be used for this purpose. 6 monthly checks 1. All fastenings and cables should be checked for tightness and wear. 2. Regular checks should be performed to ensure that the outer sheaths of the cables are not damaged and that the cables are not fouling on any obstruction. NOTE This installation guide cannot cover all conceivable cases of installation, operation or maintenance. Should you require further information or should special problems occur which are not discussed in adequate detail in the installation guide, please request the required information from your local Siemens office. We must also point out that the contents of this installation guide do not constitute a part of an earlier or existing agreement. Neither do they constitute or amend any earlier or existing commitment or legal relationship. All obligations on the part of Siemens result from the relevant purchase agreement which also contains the complete and solely valid warranty regulations. This installation guide neither extends nor restricts these contractual warranty regulations. 7 Disposal All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities. This crossed-out wheeled bin symbol on the product means the product is covered by the European Directive 2002/96/EC. The correct disposal and separate collection of your old appliance will help prevent potential negative consequences for the environment and human health. It is a precondition for reuse and recycling of used electrical and electronic equipment. For more detailed information about disposal of your old appliance, please contact your city office, waste disposal service or the shop where you purchased the product. 20

21

22 Issued by Fire & Security Products GmbH & Co. ohg D Karlsruhe Copyright by Data and design subject to change without notice. Supply subject to availability. Document no. A6V Edition