MEDICAL ALERT SETUP GUIDE

Transcription

1 MEDICAL ALERT SETUP GUIDE

2 GETTING STARTED You have made a great decision to protect yourself with Medical Alert! Be sure to wear your wrist button or neck button everyday to stay protected all the time! Enclosed please find your Medical Alert Monitoring Service Agreement filled out with the information provided to us at the time of your order. Please review all the information carefully to ensure its accuracy. If updates are needed, please call us at Sign and date the bottom of the Monitoring Service Agreement where indicated and return it to us in the postage paid envelope provided for you. Keep the second copy for your records. Fill out the enclosed Medical Information Card and place it on your refrigerator for quick reference in case of an emergency. 2 EASY WAYS TO SETUP 1. Follow instructions in this User Manual 2. Visit our website at 2

3 ABOUT YOUR SYSTEM Front Help Button Status Light Back T/L (Test/Learn) Button Wall Jack Phone Reset Button Wrist Button Neck Button 3

4 SETUP Plug the power cube into an electrical outlet not controlled by a light switch. Your system will announce, System Ready when it s properly connected. Power Cube Electrical Outlet Base Unit Wall Phone Phone Phone Cord That Came in Box Existing Phone Cord Telephone Wall Jack 4 TRADITIONAL TELEPHONE SERVICE SETUP 1. Cable Users: 1) Plug the power cube into an electrical outlet that is not controlled by a light switch. Your system will announce, System Ready when it s properly connected. 2) Locate the phone cord already plugged into the base unit. Plug smaller end into the phone jack on the wall (or the jack usually marked Phone 1 on the VOIP modem if the house wiring is not used). 3) Plug the phone wire from your phone into the jack marked PHONE on the base unit. Phone Cord to Phone WALL PHONE WALL PHONE RESET T/L Phone Cord to Wall Jack or Modem RESET T/L

5 SETUP AND TEST TRADITIONAL TELEPHONE SERVICE SETUP CONTINUED 2. DSL Users: 1) Make sure a DSL filter is plugged in the phone jack where your medical alarm unit will be plugged in. If you don t have one, you can get one from your phone service provider. CORDLESS PHONE USERS: 3. Cordless Phone Users: 1) Make sure your device is plugged into the main base unit of your cordless phone, not a satellite phone. 2) Cordless phone must be a minimum of 12 from the alarm unit to prevent blocking of signals. Phone Cord to Phone Cord WALL PHONE RESET T/L TEST YOUR DEVICE3. Cordless Phone Users: 1) From your home phone, call to put your account in TEST mode. Follow the voice prompts and put your account on TEST for 15 minutes. Hang up the telephone. 2) Press your wrist or neck button. The Medical Alert unit will recognize your TEST signal. 3) The Home Test Line will verify your address and let you know the signal was received. When prompted, say your name aloud without picking up your phone. A recording of what was heard will be played back to you. If the Home Test Line does not respond, if you do not hear your voice repeated or if you experience any problem with your testing, please call and press Option #3 for assistance. 5

6 USING YOUR SYSTEM TEST THE RANGE OF YOUR WRIST OR NECK BUTTON -- TEST/LEARN (T/L) BUTTON RANGE To make sure your system works throughout your home, conduct the following range test. Have one person stay near the base unit while you walk around to different areas of your home to test the neck or wrist button. How to Conduct Your Test 1) The white T/L (Test/Learn) button is located on the back of your medical alarm unit. Press and release it one time. The unit will announce Range Test Mode. PHONE 2) Immediately press and hold your wrist or neck button. A steady tone will sound from the base unit speaker as long as it detects that the button is being pressed. 3) Walk around the home while continuing to press and hold the Button wrist or neck button and check for the steady tone from the base unit speaker. Check all areas of the home to make sure the signal is received. Take note of any dead zones in which the tone stops.* 4) To finish the Range Test, release the wrist or neck button. Press the black RESET button on the rear of the base unit. The device will announce, System Ready. *If needed, relocate your Medical Alert base unit to eliminate any dead zones and conduct another range test. RESET T/L T/L Button 6

7 USING YOUR SYSTEM PLACING A CALL 1) In the event of an actual emergency, Button simply press your wrist or neck button or the base unit s HELP button. 2) The operator will talk to you through the unit s speaker and ask if you need help. In the event that you cannot communicate with the Response Center operator, emergency help will be dispatched. Note: When your button is pressed, the light flashes green to indicate the button batteries are OK; a red light indicates the button batteries may be weak. Every time the Response Center receives a signal from your button, its battery status is recorded. RESET BUTTON 1) The black RESET button is located on the back of your base unit. Whenever the RESET button is pressed, the unit will do a self-diagnostic test. If working properly, the unit will revert to system ready status and is ready to transmit alarms from your wrist or neck button or the base unit HELP button. ONE RESET T/L Reset Button 7

8 USING YOUR SYSTEM CANCELLING A CALL The black RESET button can be use to cancel a call for help if your device is inadvertently activated. Press the RESET button within seconds of activation otherwise the medical alarm base unit will already be communicating with the Response Center. If you cannot cancel your call within this time frame, please allow the base unit to complete the call to the Response Center and tell the operator you accidentally activated your device. RESET T/L Reset Button 8 TURNING THE CONSOLE ON AND OFF The Medical Alert unit does not have an ON/OFF switch. It will automatically turn on when first connected to electric power supply. 1) To turn off the unit, unplug the power cube from the electrical outlet AND unplug the telephone line and then press the T/L button three (3) times. The unit will announce Hold Help to Turn off. 2) Press and hold the HELP button on base unit until the STATUS light on the edge of the unit next to the HELP button goes out. This should always be done if shipping the unit or when traveling with the unit. WALL PHONE Help Button *Remember to plug the phone back into your telephone jack or modem. RESET T/L HELP

9 TROUBLESHOOTING STATUS LIGHT SIGNALS Red Light Status What it Means What To Do Solid Red Alarm activated. Unit is calling response center Nothing Blinking Red Not Connected to operating telephone line Check that wires are connected and properly plugged into wall jack or modem and to your unit. Light should turn green Green Light Status What it Means What To Do Solid Green All OK Nothing Blinking Green AC power is not working, running on battery power Check power source to make sure it s plugged into a wall outlet not controlled by a light switch Orange Light Status What it Means What To Do Blinking Orange AC power is not working, running on battery power AND not connected to operating telephone line Check power source to make sure it s plugged into a working wall outlet and check your phone line to make sure it is working properly 9

10 IMPORTANT INFORMATION You should set up your unit in a centrally located place in your home. This allows the two-way communication between you and the operator to work most effectively. Your Medical Alert account number is printed on the underside of your Medical Alarm unit. Your wrist and neck button are water resistant and should be worn in the bath or shower. Some electrical devices or metal objects can cause radio frequency interference and prevent the signal from reaching the antenna inside your unit. In such cases, it may be helpful to relocate your unit or move the object that is preventing the signal from being received. Need Help? Website: Toll Free: Press #3 for Tech Support Us: customercare@medicalalert.com 10

11

12 Equipment manufactured and supported in North America Park Way Broomall, PA 19008