Ellison Surface Technologies - Mexico. Coatings

Transcription

1 This certificate is granted and awarded by the authority of the Nadcap Management Council to: This certificate demonstrates conformance and recognition of accreditation for specific services, as listed in on the Qualified Manufacturers List (QML), to the revision in effect at the time of the audit for: Coatings Certificate Number: Expiration Date: 30 April 2019 Joseph G. Pinto Executive Vice President and Chief Operating Officer Performance Review Institute (PRI) 161 Thorn Hill Road Warrendale, PA

2 SCOPE OF ACCREDITATION Coatings This certificate expiration is updated based on periodic audits. The current expiration date and scope of accreditation are listed at: - Online QML (Qualified Manufacturer Listing). In recognition of the successful completion of the PRI evaluation process, accreditation is granted to this facility to perform the following: AC7108/1 Rev C - Nadcap Audit Criteria for Painting and Dry Film Lubricant Coatings (Used only for dry film lubrication and ceramic/metallic corrosion protection coatings (e.g. SermeTel ) when performed with AC7109/1, /2 or /3(to be used on audits on/afte 5 June 2015 Dry Film Lubricant Coatings Other AC7109 Rev E - Nadcap Audit Criteria for Coatings (to be used on audits before 3 December 2017) AC7109/1 Rev D - Nadcap Audit Criteria for Thermal Spray (to be used on audits before 3 June 2018) High Velocity Oxy Fuel (HVOF)/ High Velocity Air Fuel (HVAF) Plasma Thermal Spray Thickness Mechanical AC7109/3 Rev F - Nadcap Audit Criteria for Diffusion Coating Processes (AC7109/7 is also required or AC7102 is also accepted) (to be used on audiits before 3 December 2017) Pack Process Above Pack AC7109/4 Rev D - Nadcap Audit Criteria for Stripping (to be used on audits on/after 7 August 2016) Chemical Electrolytic

3 #2 Guaymas, SONORA AC7109/5 Rev F - Nadcap Audit Criteria for Coating Evaluations (Laboratory) (Req'd for all Coatings audits - except suppliers using Nadcap approved AC7109/5 labs)(to be used on audits before 3 December, 2017) Bond Strength Bend Bond Strength Tensile Coating Composition by Electron Microscopy Hardness Rockwell Metallography/Microstructure Microindentation Hardness Vickers Thickness Metallographic

4 This certificate is granted and awarded by the authority of the Nadcap Management Council to: This certificate demonstrates conformance and recognition of accreditation for specific services, as listed in on the Qualified Manufacturers List (QML), to the revision in effect at the time of the audit for: Heat Treating Certificate Number: Expiration Date: 31 January 2020 Joseph G. Pinto Executive Vice President and Chief Operating Officer Performance Review Institute (PRI) 161 Thorn Hill Road Warrendale, PA

5 SCOPE OF ACCREDITATION Heat Treating This certificate expiration is updated based on periodic audits. The current expiration date and scope of accreditation are listed at: - Online QML (Qualified Manufacturer Listing). In recognition of the successful completion of the PRI evaluation process, accreditation is granted to this facility to perform the following: AC7101/4 Rev F - Nadcap Audit Criteria for Materials Testing Laboratories - Metallography and Microindentation Hardness (to be used on audits on/after 14 August 2016) (L0) Metallography Evaluation Industry Spec Other L0 AC7102 Rev J - Nadcap Audit Criteria for Heat Treating Baseline (AC7102/S and AC7102/8 must also be selected) (to be used on audits on/after 3 December 2017) Brazing AC7102/1 must also be selected Vacuum Heat Treating Customer Specs Vacuum Heat Treating Industry Specs Check any applicable boxes AC7102S Rev G - Nadcap Supplemental Audit Criteria for Heat Treating (to be used on audits on/after 16 April, 2017) U3 Rolls Royce PLC U7 MTU Aero Engines GmbH AC7102/1 Rev F - Nadcap Audit Criteria for Heat Treating - Brazing (to be used on audits on/after 10 July 2016) Vacuum Brazing Customer Specs Vacuum Brazing Industry Specs Check any applicable boxes Industry Spec Other AC7102/8 - Nadcap Audit Criteria for Heat Treating Pyrometry Pyrometry Customer Specs

6 #2 Guaymas, SONORA Pyrometry Industry Specs Check any applicable boxes AMS2750

7 This certificate is granted and awarded by the authority of the Nadcap Management Council to: This certificate demonstrates conformance and recognition of accreditation for specific services, as listed in on the Qualified Manufacturers List (QML), to the revision in effect at the time of the audit for: NonDestructive Testing Certificate Number: Expiration Date: 31 July 2019 Joseph G. Pinto Executive Vice President and Chief Operating Officer Performance Review Institute (PRI) 161 Thorn Hill Road Warrendale, PA

8 SCOPE OF ACCREDITATION NonDestructive Testing This certificate expiration is updated based on periodic audits. The current expiration date and scope of accreditation are listed at: - Online QML (Qualified Manufacturer Listing). In recognition of the successful completion of the PRI evaluation process, accreditation is granted to this facility to perform the following: AC7114 Rev K - Nadcap Audit Criteria for NonDestructive Testing (NDT) Suppliers Accreditation (to be used on audits before 31 December 2017) AC7114S Rev L - Nadcap Supplemental Audit Criteria for NonDestructive Testing (NDT) Suppliers Accreditation Program (to be used on audits before 31 December, 2017) S U10 GE AC7114S Rev M - Nadcap Supplemental Audit Criteria for NonDestructive Testing (NDT) Suppliers Accreditation Program (to be used on audits on/after 31 December, 2017) S U10 GE AC7114/1 Rev J - Nadcap Audit Criteria for NonDestructive Testing Facility Penetrant Survey (to be used on audits before 31 December 2017) AC7114/1S Rev K - Nadcap Supplemental Audit Criteria for Penetrant Suppliers Accreditation Program (to be used on audits before 31 December 2017) S U10 GE AC7114/1S Rev L - Nadcap Supplemental Audit Criteria for Penetrant Suppliers Accreditation Program (to be used on audits on/after 31 December 2017) S U10 GE