Ductility SAE J81 (Sec. 4.8) ASME/ANSI B M; Customer Specified Requirements
|
|
- Theodore Maximillian Caldwell
- 6 years ago
- Views:
Transcription
1 SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 SPECIALTY SCREW CORPORATION 2801 Huffman Boulevard Rockford, IL Beth Halfman Phone: MECHANICAL Valid To: November 30, 2017 Certificate Number: In recognition of the successful completion of the A2LA evaluation process, accreditation is granted to this laboratory to perform the following fastener tests: Test(s): Case Depth (Total and Effective) Coating Thickness Decarburization Test Method(s): SAE J423 ASTM B499 SAE J121, J121M Ductility SAE J81 (Sec. 4.8) Hardness (Rockwell: A, B, C, 15N, 30N) Macroscopic Examination Microhardness (Knoop, 500 gf) Salt Spray (Fog) Sample Preparation Sample Selection ASTM E18 ASTM E340, F788; SAE USCAR-8 ASTM E384 ASTM B117 ASTM E3 ASME/ANSI B M; Customer Specified Requirements Stress Durability (Hydrogen Embrittlement) ASTM F606/F606M; J81 (Sec. 4.9) Surface Roughness ASME B46.1 Tensile (Axial & Wedge) ASTM F606/F606M (Sec. 3.1, 3.4, 3.5, 6.7); SAE J429, J1199 Torsional Strength SAE J81 (Sec. 4.5) (A2LA Cert. No ) 12/22/2015 Page 1 of 3
2 I. Dimensional Testing 1 Parameter Range CMC 2 (±) Technique / Method Angle 3 0 to Comparator / MIL-STD 120 Linear 3 MIL-STD 120 Up to 6 in Up to 1 in Up to 6 in in in in Comparator Digital micrometer Digital caliper Radii 3 (0.005 to 1) in in Comparator / MIL-STD 120 Recesses 3 #1 to # in Penetration gage / MIL-STD 120 Straightness 3 Up to in in Concentricity and Straightness Gages / MIL-STD 120 Threads 3 ASME B1.3M (System 21 and System 22) #4 to 5/8 in (0.100 to 0.700) in (0.100 to 0.700) in N/A in in Ring gages Tri-roll Pitch micrometer 1 This laboratory offers dimensional testing service only. 2 Calibration and Measurement Capability (CMC) is the smallest uncertainty of measurement that a laboratory can achieve within its scope of accreditation when performing more or less routine measurements of nearly ideal measurement standards or nearly ideal measuring equipment. Calibration and Measurement Capabilities represent expanded uncertainties expressed at approximately the 95 % level of confidence, usually using a coverage factor of k = 2. The actual measurement uncertainty of a specific measurement performed by the laboratory may be greater than the CMC due to the behavior of the customer s device and to influences from the circumstances of the specific measurement. 3 This test is not equivalent to that of a calibration. (A2LA Cert. No ) 12/22/2015 Page 2 of 3
3 4 This laboratory s scope contains withdrawn or superseded methods. As a clarifier, this indicates that the applicable method itself has been withdrawn or is now considered historical and not that the laboratory s accreditation for the method has been withdrawn. (A2LA Cert. No ) 12/22/2015 Page 3 of 3
4 Accredited Laboratory A2LA has accredited SPECIALTY SCREW CORPORATION Rockford, IL for technical competence in the field of Mechanical Testing This laboratory is accredited in accordance with the recognized International Standard ISO/IEC 17025:2005 General requirements for the competence of testing and calibration laboratories. This accreditation demonstrates technical competence for a defined scope and the operation of a laboratory quality management system (refer to joint ISO-ILAC-IAF Communiqué dated 8 January 2009). Presented this 22 nd day of December President & CEO For the Accreditation Council Certificate Number Valid to November 30, 2017 For the tests to which this accreditation applies, please refer to the laboratory s Mechanical Scope of Accreditation.
5 Certificate of Registration This is to certify that the quality management system of SPECIALTY SCREW CORPORATION 2801 Huffman Boulevard, Rockford, IL, 61103, USA has been assessed and registered by Intertek as conforming to the requirements of ISO/TS 16949:2009 The quality management system is applicable to The Manufacture of Screw, Bolts, Pins, Cold Formed Products and Automated Parts Sorting Permissible exclusions include: Product Design IATF Certificate Number: Certificate Number: Certificate Issue Date: Certificate Expiry Date: March September 2018 Calin Moldovean, President Intertek 4700 Broadmoor, Suite 200, Kentwood MI 49512, USA In the issuance of this certificate, Intertek assumes no liability to any party other than to the Client, and then only in accordance with the agreed upon Certification Agreement. This certificate s validity is subject to the organization maintaining their system in accordance with Intertek s requirements for systems certification. Validity may be confirmed via at certificate.validation@intertek.com or by scanning the code to the right with a Smartphone. The certificate remains the property of Intertek, to whom it must be returned upon request. CT-ISO/TS 16949:2009-eng-01.apr.14 Page 1 of 1
6 Certificate of Registration This is to certify that the quality management system of Specialty Screw Corp. Main Site: 2801 Huffman Boulevard, Rockford, Illinois, 61103, USA has been assessed and registered by Intertek as conforming to the requirements of ISO 9001:2008 The quality management system is applicable to Manufacture of screws, bolts, pins, cold formed products and automated parts sorting. Certificate Number: Initial Certification Date: Certificate Issue Date: Certificate Expiry Date: QMS q October March September 2018 Calin Moldovean, President Intertek Testing Services NA, Inc. 900 Chelmsford Street, Suite 301-3, Lowell, MA, USA In the issuance of this certificate, Intertek assumes no liability to any party other than to the Client, and then only in accordance with the agreed upon Certification Agreement. This certificate s validity is subject to the organization maintaining their system in accordance with Intertek s requirements for systems certification. Validity may be confirmed via at certificate.validation@intertek.com or by scanning the code to the right with a smartphone. The certificate remains the property of Intertek, to whom it must be returned upon request. CT-ISO ANAB-EN-LT-L-26.jun.15
SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005. PJF Rockford Park Drive Rockford, MI Bernard Warchuck Phone: MECHANICAL
SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 PJF 6 301 Rockford Park Drive Rockford, MI 49341 Bernard Warchuck Phone: 616 866 8296 MECHANICAL Valid To: SEE FOOTNOTE 6 Certificate Number: 1856.01 In recognition
More informationSCOPE OF ACCREDITATION TO ISO/IEC 17025:2005. PJF Rockford Park Drive Rockford, MI Bernard Warchuck Phone: MECHANICAL
SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 PJF 6 301 Rockford Park Drive Rockford, MI 49341 Bernard Warchuck Phone: 616 866 8296 MECHANICAL Valid To: SEE FOOTNOTE 6 Certificate Number: 1856.01 In recognition
More informationCERTIFICATE OF ACCREDITATION ISO/IEC 17025:2005 ANSI/NCSL Z
CERTIFICATE OF ACCREDITATION ANSI-ASQ National Accreditation Board 500 Montgomery Street, Suite 625, Alexandria, VA 22314, 877-344-3044 This is to certify that Quality Engineering Service of the Chippewa
More informationSCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 & ANSI/NCSL Z ATC INC Guion Lane Indianapolis, IN Hemi Sagi Phone:
SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 & ANSI/NCSL Z540-1-1994 4037 Guion Lane Indianapolis, IN 46268 Hemi Sagi Phone: 317 328 8492 CALIBRATION Valid To: March 31, 2019 Certificate Number: 2197.01
More informationCERTIFICATE OF ACCREDITATION
CERTIFICATE OF ACCREDITATION ANSI-ASQ National Accreditation Board 500 Montgomery Street, Suite 625, Alexandria, VA 22314, 877-344-3044 This is to certify that Productivity Quality, Inc./Advanced Inspection
More informationCERTIFICATE OF ACCREDITATION
CERTIFICATE OF ACCREDITATION ANSI-ASQ National Accreditation Board 500 Montgomery Street, Suite 625, Alexandria, VA 22314, 877-344-3044 This is to certify that Productivity Quality, Inc./Advanced Inspection
More informationSCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 & ANSI/NCSL Z
SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 & ANSI/NCSL Z540-1-1994 J.H. METROLOGY CO., INC. 1801 Hicks Road, Unit E Rolling Meadows, IL 60008 Neil E. Willert Phone: 847 991 0290 CALIBRATION Valid To:
More informationCertificate of Accreditation
PERRY JOHNSON LABORATORY ACCREDITATION, INC. Certificate of Accreditation Perry Johnson Laboratory Accreditation, Inc., has assessed the Laboratory of: (Hereinafter called the Organization) and hereby
More informationCERTIFICATE OF ACCREDITATION
CERTIFICATE OF ACCREDITATION ANSI-ASQ National Accreditation Board 500 Montgomery Street, Suite 625, Alexandria, VA 22314, 877-344-3044 This is to certify that 2105 Seabrook Circle Seabrook, TX 77586 has
More informationANALYTICAL SERVICES DIVISION, VHG LABS Manchester, NH for technical competence in the field of
A2LA has accredited ANALYTICAL SERVICES DIVISION, VHG LABS Manchester, NH for technical competence in the field of Chemical Testing This laboratory is accredited in accordance with the recognized International
More informationCERTIFICATE OF ACCREDITATION ISO/IEC 17025:2005 ANSI/NCSL Z
CERTIFICATE OF ACCREDITATION ANSI-ASQ National Accreditation Board 500 Montgomery Street, Suite 625, Alexandria, VA 22314, 877-344-3044 This is to certify that Coherent LSM 27650 SW 95th Ave. Wilsonville,
More informationSCOPE OF ACCREDITATION TO ISO/IEC 17025:2005
SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 COOK RESEARCH INCORPORATED (CRI) 1 Geddes Way West Lafayette, IN 47906 Margaret McClure Phone: 765 463 7537 MECHANICAL Valid To: June 30, 2016 Certificate Number:
More informationCertificate of Accreditation
PERRY JOHNSON LABORATORY ACCREDITATION, INC. Certificate of Accreditation Perry Johnson Laboratory Accreditation, Inc. has assessed the Laboratory of: (Hereinafter called the Organization) and hereby declares
More informationCERTIFICATE OF ACCREDITATION
CERTIFICATE OF ACCREDITATION ANSI-ASQ National Accreditation Board 500 Montgomery Street, Suite 625, Alexandria, VA 22314, 877-344-3044 This is to certify that Palindrome Technologies 100 Village Ct. Hazlet,
More informationSCOPE OF ACCREDITATION TO ISO/IEC 17025:2005
SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 INTERTEK TESTING SERVICES NA INC. 3933 U.S. Route 11 Cortland, NY 13045 Terence O Beirne Phone: 607 758 6316 www.intertek.com ELECTRICAL Valid To: March 31,
More informationSCOPE OF ACCREDITATION TO ISO/IEC 17025:2017
SCOPE OF ACCREDITATION TO ISO/IEC 17025:2017 COOK RESEARCH INCORPORATED (CRI) 1 Geddes Way West Lafayette, IN 47906 Margaret McClure Phone: 765 463 7537 MECHANICAL Valid To: June 30, 2020 Certificate Number:
More informationAmerican Association for Laboratory Accreditation
Page 1 of 5 This document describes the accreditation requirements for organizations performing activities associated with Stationary Source Evaluation Testing per the requirements of ASTM D7036 (2004).
More informationSCOPE OF ACCREDITATION TO ISO/IEC 17025:2005. LAIRD TECHNOLOGIES, INC. W66 N220 Commerce Court Cedarburg, WI Adam Alger Phone:
SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 LAIRD TECHNOLOGIES, INC. W66 N220 Commerce Court Cedarburg, WI 53012 Adam Alger Phone: 262 375 4400 ELECTRICAL (EMC) Valid to: January 31, 2019 Certificate
More informationSCOPE OF ACCREDITATION TO ISO/IEC 17025:2005
SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 MICROSOFT EMC LABORATORY 1 17760 NE 67 th Court Redmond, WA 98052 Sajay Jose Email: sajose@microsoft.com Phone: 425 421 9799 ELECTRICAL (EMC) Valid to: August
More informationSCOPE OF ACCREDITATION TO ISO/IEC 17025:2005
SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 A TEST LAB TECHNO CORP. 101-104, 1F, A Building, Taoyuan Street Safflower Ridge Industrial Area, Nanshan District Shenzhen, 518055, People s Republic of China
More informationSCOPE OF ACCREDITATION TO ISO/IEC 17025:2005. CFV SOLAR TEST LABORATORY, INC Ste. A University Blvd. SE Albuquerque, NM 87106
SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 CFV SOLAR TEST LABORATORY, INC. 5600 Ste. A University Blvd. SE Albuquerque, NM 87106 Jim Crimmins (Authorized Representative) Phone: 505 998 0102 Email: Jim.Crimmins@cfvsolar.com
More informationSCOPE OF ACCREDITATION TO ISO/IEC 17025:2005
SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 SIEMIC (NANJING-CHINA) LABORATORIES 新美科 ( 南京 ) 信息技术有限公司 No. 2-1 Longcang Avenue Yuhua Economic Development Zone Yuhua District, Nanjing, 210039, People s Republic
More informationSCOPE OF ACCREDITATION TO ISO/IEC 17025:2005
SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 BAY AREA COMPLIANCE LABORATORIES CORP. No. 69 Pulongcun Puxinhu Industrial Zone, Tangxia Town Dongguan, Guangdong 523719 People s Republic of China Mr. David
More informationSCOPE OF ACCREDITATION TO ISO/IEC 17025:2005
SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 DEKRA TESTING AND CERTIFICATION, S.A.U. Parque Tecnologico de Andalucia C/ Severo Ochoa 2 29590-Campanillas, Málaga, SPAIN Jose Maria Fernandez Phone: +34 952619100
More informationIso Iec Certificate Horiba
We have made it easy for you to find a PDF Ebooks without any digging. And by having access to our ebooks online or by storing it on your computer, you have convenient answers with iso iec 17025 certificate
More informationThe International Laboratory Accreditation Cooperation (ILAC) & The International Accreditation Forum (IAF)
The International Laboratory Accreditation Cooperation (ILAC) & The International Accreditation Forum (IAF) Perspectives on ILAC & IAF Multilateral Mutual Recognition Arrangements Peter Unger, ILAC Chair
More informationCGI Group Inc - SBU Eastern, Central & Southern Europe
This is to certify that the management system of: CGI Group Inc - SBU Eastern, Central & Southern Europe Certificate Number: ISMS 21010-05 Initial Certification Date: 30 April 2009 Certificate Issue Date:
More informationAccreditation Body Evaluation Procedure for AASHTO R18 Accreditation
Accreditation Body Evaluation Procedure for AASHTO R18 Accreditation Final August 9, 2016 Page 1 of 12 Section Number Table of Contents Title of Section 0 Purpose 1 Scope 2 References 3 Objectives 4 Criteria
More informationIATF - International Automotive Task Force Rules for Achieving and Maintaining IATF Recognition IATF Rules 5 th Edition Frequently Asked Questions
Rules for Achieving and Maintaining IATF Recognition IATF Rules 5 th Edition Frequently Asked Questions The Rules for achieving and maintaining IATF Recognition 5 th Edition for IATF 16949 ( Rules 5 th
More informationSCOPE OF ACCREDITATION TO ISO/IEC 17025:2005
SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 SGS NORTH AMERICA, INC. 15150 Avenue of Science, Suite 300 1 San Diego, CA 92128 Nathan Gieselman Phone: 858 592 7100 ELECTRICAL Valid To: July 31, 2018 Certificate
More informationSCOPE OF ACCREDITATION TO ISO/IEC 17025:2005
SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 INTERTEK TESTING SERVICES NA 731 Enterprise Drive Lexington, KY 40510 Mr. James Sudduth 859 226 1000 james.sudduth@intertek.com ELECTRICAL Valid to: April 30,
More informationCAL-CERT COMPANY 6709 SOUTHEAST LAKE ROAD MILWAUKIE, OREGON 97222
This is to attest that CAL-CERT COMPANY 6709 SOUTHEAST LAKE ROAD MILWAUKIE, OREGON 97222 Calibration Laboratory CL-108 has met the requirements of AC204, IAS Accreditation Criteria for Calibration Laboratories,
More informationSCOPE OF ACCREDITATION TO ISO/IEC 17025:2005
SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 TA TECHNOLOGY (SHANGHAI) CO., LTD. Building 3, No. 145 Jintang Rd. Tangzhen Industry Park Pudong, Shanghai, People s Republic of China Mr. Zhihui (Henry) Liu
More informationSCOPE OF ACCREDITATION TO ISO/IEC 17025:2005
SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 JIANGSU YANGTZE TESTING, CERTIFCATION AND INSPECTION CORPORATION No.6-3, XingZhi Road, XingZhi Technology Park XinGang Economic Development Zone NanJing City,
More informationWorkshop Item 1 - ISO 9001: 2008 migration
Workshop Item 1 - ISO 9001: 2008 migration Joint IAF-ISO Communiqué on migration to ISO 9001: 2008 ISO 9001: 2008 does not contain any new requirements Accredited Certification to ISO 9001:2008 shall not
More informationProcess for the Evaluation and Acceptance of Building Products in the USA
Process for the Evaluation and Acceptance of Building Products in the USA Rick Okawa, P.E. Deputy Vice President of Global Services and Business Development An Integrated Building System Product Certification
More informationInter American Accreditation Cooperation. IAAC, IAF and ILAC Resolutions Applicable to IAAC MLA Peer Evaluations
IAAC, IAF and ILAC Resolutions Applicable to IAAC MLA Peer Evaluations CLASSIFICATION This document is classified as an IAAC Mandatory Document. AUTHORIZATION Issue Nº: 07 Prepared by: MLA Committee and
More informationAn unofficial translation, in case of any discrepancies between the English version and the original Swedish version the latter will prevail.
An unofficial translation, in case of any discrepancies between the English version and the original Swedish version the latter will prevail. Consolidated version of The Swedish Board for Accreditation
More informationS. Scholz / K. Meyer / J.E. Nielsen / Harald Drück/J.Fernández/E.Prado/L.Nelson Page 1 of 7
Global Solar Certification Network Working Rules Annex A. Requirements for Certification Bodies and their subcontracted laboratories, inspection bodies and inspectors Date: 2017/03/07 Document number:
More informationMinimum Scheme Requirements to Certify Criminal Justice Restraints Described
This document is scheduled to be published in the Federal Register on 07/13/2017 and available online at https://federalregister.gov/d/2017-14638, and on FDsys.gov Billing Code: 4410-18 DEPARTMENT OF JUSTICE
More informationStrengthening International Systems of Conformity Assessment
2011/SOM1/SCSC/CON1/014 Session 8 Strengthening International Systems of Conformity Assessment Submitted by: International Laboratory Accreditation Cooperation (ILAC) 6 th Conference on Good Regulatory
More informationSCOPE OF ACCREDITATION TO ISO/IEC 17025:2005
SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 QUALITECH EMC & Product Safety Laboratory 30 Hasivim Street Petah-Tikva, 4959388, ISRAEL Teodor Weisz Phone: +972 3 926 6218 Email: Tedy.Weisz@ecitele.com Rami
More informationIAF Mandatory Document for the Transfer of Accredited Certification of Management Systems
IAF MD 2:2007. International Accreditation Forum, Inc. IAF Mandatory Document IAF Mandatory Document for the Transfer of Accredited Certification of Management Systems (IAF MD 2:2007) IAF MD2:2007 International
More informationDate 1. Each CB shall be fully transitioned for ISO 9001:2015 per IAF ID 9 and ANAB Accreditation Rule 20.
Issue: 350 Date: 2016/10/24 To: ANAB-Accredited and Applicant CBs and MS Accreditation Assessors From: Dale Gordon, Accreditation Manager, AS&D Re: Update on AQMS Standards Transition This is heads up
More informationLaboratory Accreditation Building Confidence on Testing Quality
Laboratory Accreditation Building Confidence on Testing Quality Dr. George Anastasopoulos, Director (Conformity Assessment) & Prasanth S Ramakrishnan, MS, LEED-AP (Principal Staff & Program Manager) ASME
More informationACCREDITATION COMMISSION FOR CONFORMITY ASSESSMENT BODIES
ACCREDITATION COMMISSION FOR CONFORMITY ASSESSMENT BODIES ACCREDITATION SCHEME MANUAL Document Title: Document Number: Various Accreditation Schemes ACCAB-ASM-7.0 CONTROLLED COPY Revision Number Revision
More informationIATF - International Automotive Task Force Rules for achieving and maintaining IATF Recognition IATF Rules 5 th Edition Sanctioned Interpretations
Rules for achieving and maintaining IATF Recognition IATF Rules 5 th Edition Sanctioned Interpretations The Rules for achieving and maintaining IATF Recognition 5 th Edition for IATF 16949 ( Rules 5 th
More informationSCOPE OF ACCREDITATION TO ISO/IEC 17025:2005
SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 SHENZHEN MORLAB COMMUNICATIONS TECHNOLOGY CO. LTD. Fl. 3, Building A, Fei Yang Science Park No. 8 Long Chang Road, Block 67 BaoAn District, Guangdong Province,
More informationCERTIFICATE OF ACCREDITATION
CERTIFICATE OF ACCREDITATION ANSI-ASQ National Accreditation Board/ACLASS 500 Montgomery Street, Suite 625, Alexandria, VA 22314, 877-344-3044 This is to certify that 80 Industrial Drive Alpha, NJ 08865
More informationATI Flat Rolled Products Holdings LLC. Materials Testing
This certificate is granted and awarded by the authority of the Nadcap Management Council to: 1300 Pacific Ave Natrona Heights, PA 15065 United States This certificate demonstrates conformance and recognition
More informationSCOPE OF ACCREDITATION TO ISO/IEC 17025:2005
SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 ECI TELECOM S LQLAB 30 Hasivim Street Petah-Tikva 4959338, ISRAEL Moshe Perel Phone: 972 52-4008642 Email: Moshe.Perel@ecitele.com ELECTRICAL Valid to: June
More informationIATF Transition Strategy Presenter: Mrs. Michelle Maxwell, IAOB
IATF 16949 Transition Strategy Presenter: Mrs. Michelle Maxwell, IAOB IATF 16949 Transition Strategy IATF 16949 transition strategy was presented at the IATF global stakeholder conference in Rome, Italy
More informationSCOPE OF ACCREDITATION TO ISO/IEC 17025:2005. CETECOM INC. 411 Dixon Landing Road Milpitas, CA Franz Engert Phone: ELECTRICAL
SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 CETECOM INC. 411 Dixon Landing Road Milpitas, CA 95035 Franz Engert Phone: 408 586 6205 ELECTRICAL Valid to: May 31, 2018 Certificate Number: 2135.01 In recognition
More informationSCOPE OF ACCREDITATION TO ISO/IEC 17025:2005
SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 BAY AREA COMPLIANCE LABORATORIES CORP. 6/F, the 3rd Phase of WanLi Industrial Building Shihua Road, Futian Free Trade Zone Shenzhen, Guangdong 518038 People
More informationWho is doing your calibration work?
The United Kingdom Accreditation Service Who is doing your calibration work? Are you confident that your goods and services and their component parts are based on measurements taken with correctly calibrated
More informationPRESENTATION OVERVIEW
ITU Regional Seminar for the Africa Region on Conformance and Interoperability Testing Centre(s) Accra (Ghana), 4-6 July 2011 Accreditation Bodies Presented by Andrew Kwan ITU Consultant 1 PRESENTATION
More informationR318 - Specific Requirements: Forensic. Examination Accreditation Program - Inspection
Page 1 of 6 Examination Accreditation Program - October 2015 2015 by A2LA. All rights reserved. No part of this document may be reproduced in any form or by any means without the prior written permission
More informationACCREDITATION COMMISSION FOR CONFORMITY ASSESSMENT BODIES
ACCREDITATION COMMISSION FOR CONFORMITY ASSESSMENT BODIES ACCREDITATION SCHEME MANUAL Document Title: Document Number: Various Accreditation Schemes ACCAB-ASM-7.0 CONTROLLED COPY Revision Number Revision
More informationSCOPE OF ACCREDITATION TO ISO/IEC 17025:2005
SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 A TEST LAB TECHNO CORP. No.140-1, Changan Street Bade District Taoyuan City, Taiwan (R.O.C.) Kevin Tsai email: kevin@atl-lab.com.tw Phone: 886-3-2710188 Ext.
More informationIAF Informative Document. Information on the Transition of Management System Accreditation to ISO/IEC :2015 from ISO/IEC 17021:2011
IAF Informative Document Information on the Transition of Management System Accreditation to ISO/IEC 17021-1:2015 from ISO/IEC 17021:2011 Issue 1 (IAF ID 11:2015) Issue 1 Information on the Transition
More informationSCOPE OF ACCREDITATION TO ISO/IEC 17025:2005
SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 SHENZHEN ACADEMY OF METROLOGY AND QUALITY INSPECTION 1 NETC Building, No. 4 Tongfa Road Xili, Nanshan Shenzhen, Guangdong, 518055, People s Republic of China
More informationINAB Mandatory and Guidance Documents Policy and Index
INAB Mandatory and Guidance s Policy and Index This publication is aimed at assisting in determining what documents are relevant to various organisations and at providing contact points for accessing such
More informationNational Cooperation for Laboratory Accreditation Annual General Meeting International versus National Recognition: A Comparison
National Cooperation for Laboratory Accreditation Annual General Meeting International versus National Recognition: A Comparison August 2011 1 Purpose of International Recognition Simply put, the purpose
More informationExcel Calibration Private Limited, No. 101, Legend Constructions, No /101, Barkathpura, Hyderabad, Telangana
Last Amended on 10.03.2016 Page 1 of 5 I. DINENSION 1. GAUGE BLOCKS $ (Grade 0, I & II) 0.5 mm to 10 mm 0.4 µm Using Gauge Block 10 mm to 25 mm 0.6 µm Comparator & Slip Gauges 25 mm to 50 mm 0.7 µm 50
More informationR103 - GENERAL REQUIREMENTS: PROFICIENCY TESTING FOR ISO/IEC LABORATORIES
Page 1 of 8 R103 - GENERAL REQUIREMENTS: PROFICIENCY TESTING FOR ISO/IEC 17025 2018 2018 by A2LA All rights reserved. No part of this document may be reproduced in any form or by any means without the
More informationILAC The International Laboratory Accreditation Cooperation IAF The International Accreditation Forum Latest developments
ILAC The International Laboratory Accreditation Cooperation IAF The International Accreditation Forum Latest developments 49 th CIML Meeting (04-06 November 2014) Auckland IAF and ILAC Objectives To maintain
More informationStakeholder Rules: Rue Montoyer, 10 B-1000 Brussels, Belgium Telephone: Fax:
International Aerospace Quality Group (IAQG) Other Party Management Team (OPMT) Supplemental Rule 003 Rules for 9100/9110/9120:2016 and 9101:2016 Transition Dated: October 12, 2016, Revised December 12,
More information9.2" INDICATOR WITH ERGONOMIC DIAL FASCIA PAT. PEND , ,
9." N /6 IN HEX DRIVE SMA 3.5 K.4.85 X X SMA ERGO GAGES: RESOLUTION 0005 ACCURACY +/-00 USB DRIVE WITH CAL DATA 8 - + 0 7 Starrett 9 0005 6 Athol, MA USA GPC K.85 ~ 3.5mm SMA GAGE INDICATOR WITH OMIC DIAL
More informationList of EA Publications. And International. Documents
EA/INF-01 List of EA Publications and International Documents Publication Reference EA-INF/01: 2018 List of EA Publications And International Documents PURPOSE This gives the list of EA documents to be
More informationIATF Transition Strategy Presenter: Cherie Reiche, IAOB
IATF 16949 Transition Strategy Presenter: Cherie Reiche, IAOB IATF 16949 Transition Strategy IATF 16949 transition strategy was presented at the IATF global stakeholder conference in Rome, Italy in April
More informationReliance Calibration Laboratory, Sr. No. 21/7, (Gokul Nagar, Narhe), Lygude Estate, Dhayari-Sinhgad Road, Pune, Maharshtra
Last Amended on 20.10.2014 Page 1 of 8 I. DIMENSION 1. Caliper $ (Digital/ Dial/ Analogue) L.C.: 0.01 mm ф 0 to 300 mm 0 to 600 mm 0 to 1000 mm 14.0 µm 15.0 µm 19.0 µm Using Caliper Checker & Length Bars
More informationMicro-Flat Datums Pvt. Ltd., Plot No , Zone D-3, GIDC, Vitthal Udyognagar, Anand, Gujarat
Last Amended on 03.12.2015 Page 1 of 9 I. DIMENSION 1. CALIPERS $ L.C.: 0.01 mm Φ L.C.: 0.02 mm Φ 0 to 600 mm 0 to 1000 mm 0 to 2000 mm 9.37 µm 9.25 µm 14.64 µm Using Slip Gauge Set, Caliper Checker, Master
More informationMINIMUM QUALIFICATIONS FOR SPECIAL INSPECTORS, Fabricators, Special Inspection Agencies, Testing Labs and Laboratory Technicians
MINIMUM QUALIFICATIONS FOR SPECIAL INSPECTORS, Fabricators, Special Inspection Agencies, Testing Labs and Laboratory Technicians ORION TOWNSHIP BUILDING DEPARTMENT A. FABRICATORS A.1. Fabricators: Not
More informationGUIDANCE AND INTERPRETATION DOCUMENTS TO THE REQUIREMENTS FOR THE COMPETENCE OF CONFORMITY ASSESSMENT BODIES
GUIDANCE AND INTERPRETATION DOCUMENTS TO THE REQUIREMENTS FOR THE COMPETENCE OF CONFORMITY ASSESSMENT BODIES Table of Contents 1 PURPOSE... 2 2 GENERAL... 2 3 GUIDANCE AND INTERPRETATIVE DOCUMENTS... 2
More informationAccreditation Criteria For Conformity Assessment Bodies
Page 1 of 8 Reviewed by: Getnet Tsigemalak Approved by: Araya Fesseha Position: Quality Manager Position: Director General Signature: Signature: Contents Page 1 Purpose and Scope... 2 2 References... 2
More informationDAkkS Who we are. Attesting competence, Assuring quality, Creating confidence.
DAkkS Who we are Attesting competence, Assuring quality, Creating confidence. What is accreditation? Reliability through conformity assessment The demands on the quality of goods and services are growing
More informationAccreditation and Registration 07/25/18
Accreditation and Registration 07/25/18 THE DIETARY SUPPLEMENT SPECIALISTS ADVANCED LABORATORIES ACCREDITATION AND REGISTRATION DOCUMENTS PAGE CONTENT 3 UT CERTIFICATE OF FDA REGISTRATION 4-6 UT SCOPE
More informationAustralian Standard. General requirements for the competence of testing and calibration laboratories AS ISO/IEC ISO/IEC 17025:1999
AS ISO/IEC 17025 1999 ISO/IEC 17025:1999 AS ISO/IEC 17025 Australian Standard General requirements for the competence of testing and calibration laboratories This is a free 7 page sample. Access the full
More informationPart 5: Requirements for ABs FOOD SAFETY SYSTEM CERTIFICATION Part V: Requirements for Accreditation Bodies
Part 5: Requirements for ABs FOOD SAFETY SYSTEM CERTIFICATION 22000 Part V: Requirements for Accreditation Bodies Version 4.1: July 2017 Part V: Requirements for Accreditation Bodies Contents 1 Purpose...
More informationNOTE: This includes Aerospace Auditors (AAs) and Aerospace Experienced Auditors (AEAs)
Purpose: Provide supplemental rules for all stakeholders to facilitate the transition to the 9100/9110/9120:2009 Aerospace Quality Management Systems (AQMS) standards, including use of the updated 9101.
More informationConsumer Product Safety Certification IOM Workshop on Certification April 13, 2010
Consumer Product Safety Certification IOM Workshop on Certification April 13, 2010 This presentation has not been reviewed or approved by the Commission and may not reflect its views 1 What Products Must
More informationINAB Mandatory and Guidance Documents Policy and Index
INAB Mandatory and Guidance s Policy and Index This publication is aimed at assisting in determining what documents are relevant to various organisations and at providing contact points for accessing such
More informationACCREDITATION COMMISSION FOR CONFORMITY ASSESSMENT BODIES. Advisory Document on Tenders For Systems, Processes & Product Certifications
ACCREDITATION COMMISSION FOR CONFORMITY ASSESSMENT BODIES CAB Accreditation Advisory Document Document Title: Document Number: Advisory Document on Tenders For Systems, Processes & Product Certifications
More informationREVISION 5. International Automotive Task Force TRANSITION STRATEGY ISO/TS IATF Dated 1 March
REVISION 5 Dated 1 March 2018 International Automotive Task Force TRANSITION STRATEGY ISO/TS 16949 IATF 16949 2 CONTENTS Foreword Revision 1 dated 3 October 2016 Revision 2 dated 21 November 2016 Revision
More informationEUROPEAN ACCREDITATION LEGAL FRAMEWORK
EUROPEAN ACCREDITATION LEGAL FRAMEWORK ECIBC Plenary 2016 Ed Wieles 24 November 2016 CONTENTS European model on Accreditation Requirements for Accreditation bodies Harmonised standards for accreditation
More informationProtocol on the Mutual Acceptance of the Results of Conformity Assessment
Protocol on the Mutual Acceptance of the Results of Conformity Assessment 1 Presentation Overview Overview of the Conformity Assessment (CA) Protocol Implementation and Next Steps Cooperation Agreement
More informationIECEE. IEC-ILAC-IAF Tripartite MoU CB-FCS Scheme and Market Control INTERNATIONAL ELECTROTECHNICAL COMMISSION
INTERNATIONAL ELECTROTECHNICAL COMMISSION WORLDWIDE SYSTEM FOR CONFORMITY TESTING AND CERTIFICATION OF ELECTRICAL EQUIPMENT AND COMPONENTS IECEE IEC-ILAC-IAF Tripartite MoU CB-FCS Scheme and Market Control
More informationAgreement for Use of Certification Symbols:
Agreement for Use of Certification Symbols: UL Enhanced Certification Marks, UL Enhanced Certification Badges, ANAB Accreditation Symbol, ILAC Mark, ANSI Accreditation Symbol, IAF-MLA Mark and Certificates
More informationCertificate of Accreditation
PERRY JOHNSON LABORATORY ACCREDITATION, INC. Certificate of Accreditation Perry Johnson Laboratory Accreditation, Inc. has assessed the Laboratory of: (Hereinafter called the Organization) and hereby declares
More informationIntroduction to UKAS Accreditation Fire Scene Development Programme. David Compton November 2017
Introduction to UKAS Accreditation Fire Scene Development Programme David Compton November 2017 What is UKAS Accreditation? Procedure by which an authoritative body gives formal recognition that a body
More informationSCOPE OF ACCREDITATION TO ISO/IEC 17025:2005
SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 SHENZHEN ACADEMY OF METROLOGY AND QUALITY INSPECTION 1 NETC Building, No. 4 Tongfa Road Xili, Nanshan District Shenzhen, Guangdong, 518055, People s Republic
More informationDiscontinuing the Metallic Handcuffs Compliance Testing Program and Request for
This document is scheduled to be published in the Federal Register on 09/14/2016 and available online at https://federalregister.gov/d/2016-22057, and on FDsys.gov Billing Code: 4410-18 DEPARTMENT OF JUSTICE
More informationBetter Regulatory Outcomes & the CASCO Toolbox
2011/SOM1/SCSC/CON1/013 Session 8 Better Regulatory Outcomes & the CASCO Toolbox Submitted by: Underwriters Laboratories 6 th Conference on Good Regulatory Practice Washington, D.C., United States 1-2
More informationCOOMET Recommendation Content and Rules of Drawing up Documents for CRMs Developed within COOMET
COOMET Recommendation Content and Rules of Drawing up Documents for CRMs Developed within COOMET CООМЕТ R/RM/5:2010 Endorsed at the 5 th meeting of experts on certified reference materials of COOMET member-countries
More informationResource Inspections Canada Inc. Certification Scheme Requirements
1. Purpose To describe the requirements for certification scheme for certified calibration laboratory technician for dimensional calibrations conducted by Resource Inspections Canada Incorporated. This
More informationVasals Engineering Industries, No. 33, First Floor, Govardhan Garden, J.C. Industrial Area, Kanakapura Road, Yelachenahalli, Bangalore, Karnataka
Last Amended on 01.06.2015 Page 1 of 8 I. DIMENSION 1. PLAIN PLUG 1 mm to 50 mm 2.2 µm Using LVDT Probe 100 mm to 200 mm 4.2 µm 0 Grade Gauge Blocks by Comparison 2. THREAD PLUG 3. TAPER PLAIN PLUG 4.
More informationCertification Report
Certification Report Issued by: Communications Security Establishment Certification Body Canadian Common Criteria Evaluation and Certification Scheme Government of Canada, Communications Security Establishment,
More informationCaliber Gauges & Instruments Laboratory, S. No. 14/1, Dattadigamber Soc. B, Warje Jakat Naka, Pune, Maharashtra
Last Amended on - Page 1 of 8 I. DIMENSION 1. PLAIN PLUG / WIDTH/ DEPTH / Upto 100 mm 2.0 µm Using Electronic FLUSH PIN GAUGE DIAMETER /WIDTH / DEPTH $ Above 100 to 300 mm 3.0 µm Comparator with Stand
More informationEllison Surface Technologies - Mexico. Coatings
This certificate is granted and awarded by the authority of the Nadcap Management Council to: This certificate demonstrates conformance and recognition of accreditation for specific services, as listed
More informationGlobal Wind Organisation CRITERIA FOR THE CERTIFICATION BODY
Global Wind Organisation CRITERIA FOR THE CERTIFICATION BODY December 2015 (Version 3) 1 Contents 1. Introduction... 5 2. Criteria for approval of a Certification Body... 5 3. Selection of audit team members
More information