MicroTech II Applied Rooftop Unit Controller and Self-Contained Unit Controller BACnet Communication Module MS/TP

Transcription

1 Installation and Maintenance Manual IM Group: Controls Part Number: IM 704 Date: August 2007 Supersedes: IM MicroTech II Applied Rooftop Unit Controller and Self-Contained Unit Controller BACnet Communication Module MS/TP NOTICE Use this manual to physically install the McQuay MicroTech II Communication Module into the rooftop unit controller and connect the rooftop unit controller to your network. Use the appropriate McQuay Engineering Data (ED), known as the Protocol Information document, to integrate the unit into your network. The Protocol Information document contains addressing details, BACnet protocol information, and a list of the data points available to the network. See the Reference Documents section of this manual for Protocol Information document numbers. MicroTech II control integration literature is available from your local McQuay International sales representative and McQuay International

2 Contents Figures... 2 Revision History... 3 Reference Documents... 3 Limited Warranty... 3 INTRODUCTION... 4 Recognize Safety Symbols, Words and Labels... 4 GENERAL INFORMATION... 5 DESCRIPTION... 5 APPLICATION... 6 COMPONENT DATA... 6 Light Emitting Diodes (LEDs)... 7 BACnet MS/TP Network Connector (P1)... 7 Address Switch Pin Header... 7 INSTALLATION AND NETWORK CONNECTION... 8 General... 8 Required Equipment... 8 Installing a new BACnet MS/TP Communication Module... 8 Connecting the BACnet/IP Communication Module to the Network: Applied Rooftop Units... 8 Connecting the BACnet/IP Communication Module to the Network: Self-Contained Units... 9 Replacing a BACnet MS/TP Communication Module... 9 Connecting a BACnet MS/TP Communication Module to the Network... 9 INTEGRATION NETWORK CONNECTION BACnet MS/TP Network Addressing CONFIGURING THE UNIT CONTROLLER Factory-Installed BACnet MS/TP Communication Modules Field-Installed BACnet MS/TP Communication Modules Important Notes SERVICE INFORMATION TROUBLESHOOTING REPLACEMENT PARTS Figures Figure 1. BACnet MS/TP Communication Module... 5 Figure 2. Building Automation System... 6 Figure 3. BACnet MS/TP Communication Module Major Components... 6 Figure 4. BACnet MS/TP Communication Module Mounted on the Unit Controller s Main Control Board Figure 5. Mount BACnet MS/TP Communication Module Figure 6. BACnet MS/TP Connection Schematic Diagram Figure 7. BACnet MS/TP Network Cable Routing, Applied Rooftop Units Figure 8. BACnet MS/TP Network Cable Routing, Self-Contained Units IM704-4

3 Revision History IM 704 IM IM IM November 2004 Initial release IM August 2007 Updated IP router address on Table 1. Minor formatting. Reference Documents Number Title Company Source IM696 MicroTech II Applied Rooftop Unit Controller Installation Manual McQuay International OM137 MicroTech II Applied Rooftop Discharge Air Controller Operation Manual McQuay International OM138 MicroTech II Applied Rooftop Space Comfort Controller Operation Manual McQuay International IM710 MicroTech II Vertical Self-Contained Unit Controller Installation Manual McQuay International OM711 MicroTech II Vertical Self-Contained Discharge Air Controller Operation Manual McQuay International OM712 MicroTech II Vertical Self-Contained Space Comfort Controller Operation Manual McQuay International ED15060 MicroTech II Protocol Information Data for McQuay International Applied Rooftop Units McQuay International ED15061 MicroTech II Protocol Information Data for McQuay International Self-Contained Units McQuay International E LonMark Layers 1-6 Interoperability Guidelines, Version 3.0 LonMark Interoperability Assoc E LonMark Application Layer Interoperability Guidelines, Version 3.2 LonMark Interoperability Assoc _10 LonMark Functional Profile: Space Comfort Controller, Version 1.0 LonMark Interoperability Assoc _10 LonMark Functional Profile: Discharge Air LonMark Interoperability G Controller, Version LONWORKS FTT-10A Free Topology Transceiver Users Guide Assoc. Echelon Corporation Limited Warranty Consult your local McQuay Representative for warranty details. Refer to Form Y. To find your local McQuay Representative, go to Notice Copyright 2007 McQuay International, Minneapolis MN. All rights reserved throughout the world. McQuay International reserves the right to change any information contained herein without prior notice. The user is responsible for determining whether this software is appropriate for his or her application. The following are tradenames or registered trademarks of their respective companies. BACnet from the American Society of Heating, Refrigerating and Air-Conditioning Engineers, Inc.; LONWORKS and LONMARK from Echelon, Inc.; Windows from Microsoft Corporation; McQuay and MicroTech II from McQuay International. IM

4 Introduction Recognize Safety Symbols, Words and Labels The following symbols and labels are used throughout this manual to indicate immediate or potential hazards. It is the owner and installer s responsibility to read and comply with all safety information and instructions accompanying these symbols. Failure to heed safety information increases the risk of property damage and/or product damage, serious personal injury or death. Improper installation, operation and maintenance can void the warranty.! CAUTION Hazards or unsafe practice CAN result in property damage, product damage, severe personal injury and or death. NOTICE Hazards or unsafe practices, which CAN result in property, damage, product damage, and or personal injury. IM

5 General Information This manual contains the information you need to install the MicroTech II Communication Module for BACnet MS/TP and connect it to a BACnet network.! WARNING Electric shock hazard. Can cause personal injury or equipment damage. This equipment must be properly grounded. Connections and service to the MicroTech II control panel must be performed only by personnel who are knowledgeable in the operation of the equipment being controlled.! CAUTION Static sensitive components. Can cause equipment damage. Discharge any static electrical charge by touching the bare metal inside the control panel before performing any service work. Never unplug cables, circuit board terminal blocks, or power plugs while power is applied to the panel. NOTICE This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with this instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his or her own expense. McQuay International disclaims any liability resulting from any interference or for the correction thereof. Description A MicroTech II BACnet MS/TP Communication Module incorporates a MicroTech II rooftop or self-contained unit controller into a BACnet MS/TP Local Area Network (LAN). It supports the BACnet MS/TP (EIA 485) data link layer (physical layer.) It is the interface to the Building Automation Network using BACnet objects. The BACnet MS/TP Communication Module is a printed circuit board that plugs onto the MicroTech II unit controller s main control board. Figure 1 shows an outline drawing of the BACnet MS/TP Communication Module. Figure 1. BACnet MS/TP Communication Module IM

6 Application The MicroTech II BACnet MS/TP Communication Module connects the MicroTech II applied rooftop or self-contained unit controller to the building automation system (BAS) via BACnet MS/TP LAN. It is the interface adapter for the exchange of BACnet objects between the network and the unit controller. Figure 2 shows the BACnet MS/TP Communication Module and unit controller integrated into a BAS. Figure 2. Building Automation System BACnet MSTP Network MicroTech II Main Control Board BACnet MSTP Communications Module MicroTech II Keypad Component Data Figure 3 shows the location of the major components of the BACnet MS/TP Communication Module. Figure 3. BACnet MS/TP Communication Module Major Components Network Connector Plug + _ P1 SG Transmit LED DS2 Receive LED DS1 Address Switch SW1 12 Pin Header 6 IM704-4

7 Light Emitting Diodes (LEDs) The MicroTech II BACnet MS/TP Communication Module has two LEDs to indicate communication activity and status of the communication module. LED DS1 DS2 Function Lights when the BACnet MS/TP Communication Module is receiving data Lights when the BACnet MS/TP Communication Module is transmitting data BACnet MS/TP Network Connector (P1) The P1 connector connects the MicroTech II BACnet MS/TP Communication Module to the BACnet MSTP network. Pin Designation Connection Function 1 REF TB2-130 Reference 2 N2- TB2-129 Inverting Input 3 N2+ TB2-128 Non-inverting Input Address Switch The Address Switch, SW1, must be set to the MAC address of the BACnet MS/TP Communication Module. The valid range is 0 to Pin Header The 12-pin header, J1, connects the unit controller to the BACnet MS/TP Communication Module through the bottom of the BACnet MS/TP Communication Module. IM

8 Installation and Network Connection General A BACnet MS/TP Communication Module can be factory or field-installed and can be purchased by itself or as a kit. The BACnet MS/TP Communication Module, cable harness, and this installation manual are available as a kit (see the Replacement Parts section for details). The following section describes how to install a new BACnet MS/TP Communication Module or replace an existing module. It also describes how to connect the BACnet MS/TP Communication Module it to a BACnet network. The BACnet MS/TP Communication Module mounts on connector pins and is held in place with four plastic locking standoffs. The BACnet MS/TP network connects to the BACnet MS/TP Communication Module at the network connector plug, P1. The BACnet MS/TP network cable connects TB2 in the unit cabinet. Required Equipment Field installation/replacement and network connection requires the following: A BACnet MS/TP Communication Module (included in kit) Cable harness (included in kit) Shielded, twisted pair pigtail wire and plug for network connection Small, straight-blade screwdriver Installing a new BACnet MS/TP Communication Module Note: A MAC (Media Access Control) address must be assigned to the BACnet MS/TP Communication Module. See your network administrator. 1. Remove power from the unit controller. 2. Remove the network cable plug-in connector terminal block in P1 (see Figure 3.) 3. Locate the empty connector and four standoffs for the BACnet MS/TP Communication Module on the unit controller s main control board (see Figure 4.) 4. Orient the BACnet MS/TP Communication Module printed circuit board so that the side with the components faces out and connector pins can penetrate the 12-Pin Header on the BACnet MS/TP Communication Module. 5. Push the BACnet MS/TP Communication Module onto the connector pins and standoffs until you hear the faint click of the locking standoffs securing the board in place. Connecting the BACnet/IP Communication Module to the Network: Applied Rooftop Units 1. Connect the MS/TP BACnet MS/TP Communication Module to the network with wire harness (see Figure 6). 2. Connect the cable harness clear wire (No. 522) to the N2+ terminal of the P1 connector plug and connect the black wire (No. 523) to the N2 terminal of the P1 connector plug. Note: You must maintain the polarity of the signal throughout the network. Always connect + to + and to. 3. Connect the cable harness drain wire (No. 524) to one of DRN terminals on TB6. 4. Route the cable harness down to the shelf below the unit controller and to the left along the shelf to the edge. 5. Route the cable through a hole down the cable raceway to Terminal Block TB2 (see Figure 7.) 6. Connect the cable harness clear wire (No. 522) to terminal 128 of TB2 and connect the black wire (No. 523) to terminal 129 of TB2. Note: You must maintain the polarity of the signal throughout the network. Always connect + to + and to. 8 IM704-4

9 Connecting the BACnet/IP Communication Module to the Network: Self-Contained Units 1. Connect the BACnet MS/TP Communication Module to the network with cable harness (see Figure 6). 2. Connect the cable harness clear wire (No. 522) to the N2+ terminal of the P1 connector plug and connect the black wire (No. 523) to the N2 terminal of the P1 connector plug. 3. Connect the cable harness drain wire (No. 524) to one of the DRN terminals on TB7. Note: You must maintain the polarity of the signal throughout the network. Always connect + to + and to. 4. Route the cable harness down and over to your right along the main control board and up to Terminal Block TB2 (see Figure 8.) 5. Connect the cable harness clear wire (No. 522) to terminal 128 of TB2 and connect the black wire (No. 523) to terminal 129 of TB2. Note: You must maintain the polarity of the signal throughout the network. Always connect + to + and to. 6. Connect the BACnet MS/TP network cable to TB 2 terminals 128, 129, and Set the MAC Address in Address Switch SW1 (assigned by the network administrator.) The valid range is 0 to Apply power to the unit controller. Note: Terminal 130 of TB 2 is provided as a common connection point for the shield of the network cable. The shield must be continuous throughout the entire network cable and must be connected to earth ground at one and only one point. The BACnet MS/TP network must be terminated at each end with a 120 ohm resistor between the + and - terminals Replacing a BACnet MS/TP Communication Module 1. Remove power from the unit controller. 2. Record the MAC Address set in Address Switch SW1. 3. Remove the network cable plug-in connector terminal block P1 (see Figure 3.) 4. Locate the four standoffs for the BACnet MS/TP Communication Module in the unit controller s main control board (see Figure 4.) 5. Use a pliers or screwdriver to depress the barb on one standoff and gently pull the corner of the BACnet MS/TP Communication Module over the barb. Do not bend the BACnet MS/TP Communication Module or misalign the connector pins. 6. Proceed to the other three corners, remove the BACnet MS/TP Communication Module from each standoff, and pull the module over the standoffs. 7. Gently lift the BACnet MS/TP Communication Module from the unit controller. 8. Locate the empty connector pins and four standoffs for the BACnet MS/TP Communication Module in the unit controller (see Figure 4.) 9. Orient the BACnet MS/TP Communication Module so that the component side faces out and the connector pins can penetrate the 12-Pin Header on the BACnet MS/TP Communication Module (see Figure 5.) 10. Push the BACnet MS/TP Communication Module onto the connector pins and standoffs until you hear the faint click of the locking standoffs securing the module in place. Connecting a BACnet MS/TP Communication Module to the Network 1. Replace network cable plug in P1 (see Figure 3.) 2. Reconnect the network to TB 2 terminals 128, 129, and 130 if it is necessary. 3. Set the MAC Address in Address Switch SW1 (see Step 2.) 4. Apply power to the unit controller. IM

10 Figure 4. BACnet MS/TP Communication Module Mounted on the Unit Controller s Main Control Board Main Control Board Network Connector Plug 12-Pin Header Location of Standoff (4 places) 10 IM704-4

11 Figure 5. Mount BACnet MS/TP Communication Module 12-Pin Header BACnet MSTP Communications Module Address Switch, SW1 Network Connector Plug LED Indicators Locking Stnadoff Standoff (4 Places) Figure 6. BACnet MS/TP Connection Schematic Diagram Unit Terminal Block TB2 BACnet MSTP Communication Module N2+ N2- REF TB6 (Applied Rooftop) TB7 (Self-Contained) DRN IM

12 REF Figure 7. BACnet MS/TP Network Cable Routing, Applied Rooftop Units TB6 Controller BACnet MSTP Communications Comunications Module Cable Shelf N2+ N2- BACnet MSTP Comm Card Network Cable Cable Raceway Terminal Block TB2 12 IM704-4

13 Figure 8. BACnet MS/TP Network Cable Routing, Self-Contained Units Controller BACnet MSTP Communications Coomunications Module Terminal Block TB2 Network Cable Harness TB7 IM

14 Integration Integrating the BACnet MS/TP Communication Module into a BAS involves three steps: Connecting the rooftop or self-contained unit controller to the network Addressing and establishing communications with the unit controller Configuring the unit controller Network Connection After inserting the BACnet/IP Communication Module to the MicroTech II unit controller, connect the MicroTech II unit controller into the BACnet network. You will need a straight-through ethernet cable connected to a hub (see the Installation and Network Connection section for details. BACnet MS/TP Network Addressing Follow these procedures to properly address and establish communications with the unit controller (see Table 1for details.) Verify that the MAC address of the unit controller is unique on the BACnet network Cycle power to the unit controller Change the data transmission rate, if necessary Change the default BACnet MS/TP Address The BACnet MS/TP device address (MAC) Address of the MicroTech II controller in a BACnet Master Slave/Token Passing (MSTP) Local Area Network (LAN) is set in an eight-position dipswitch on the BACnet MS/TP Communication Module (see Figure 3. BACnet MS/TP Communication Module Major Components.) The address is physically set in eight binary switches. Bit 0 of the address corresponds to switch position 1 and bit 7 of the address corresponds to switch position 8. All MicroTech II controllers must be master controllers; therefore, bit 7 is always equal to 0 (open). An open switch (switch up) is a 0, and a closed switch (switch down) is a 1. This address must be unique and is determined during installation. After you set the address in the switches, you must cycle power (turn the unit controller off and then on again) in order for the new address to take effect. The Receive LED flickers when the module is receiving data from the network, and the Transmit LED flickers when the module is sending data to the network. The default data transmission rate is set to 19,200 bps (baud). You can change the data transmission rate to 9600 or 38,400 bps. Refer to the MicroTech II Protocol Data Information Packet (See Reference Documents). The default BACnet MS/TP network address of the MicroTech II Unit Controller is You can change this address but it must be the same as all other BACnet devices on the network for devices to communicate with each other. Refer to the MicroTech II Protocol Data Information Packet (See Reference Documents section). Configuring the Unit Controller All Rooftop and Self-contained unit controllers are loaded with software and configured at the factory for stand-alone operation. The unit is ready to operate with default set point parameters that can be changed with the unit s keypad/display or via a network signal. Refer to the appropriate operation manual for the default values and keypad/display operating instructions. Refer to the appropriate MicroTech II Protocol Information documents for descriptions of the available network variables (see Reference Documents section). There are 12 communication parameters involved in setting up the unit controller for proper communication with the various communication module options (BACnet IP, BACnet MS/TP or LONWORKS ). These parameters are set differently by the factory depending on which communication module is ordered and shipped with the unit. Table 1 below lists the four possible sets of default parameter settings. Not all the parameters apply to all the communication module options. The entries in the table that are shown in bold font apply to a particular communication module option. Factory-Installed BACnet MS/TP Communication Modules If the rooftop or self-contained unit controller is equipped with a factory-installed BACnet MS/TP Communication Module, the controller is pre-configured with the values shown in Table 1. These parameters do not require field modification. 14 IM704-4

15 Field-Installed BACnet MS/TP Communication Modules A BACnet MS/TP Communication Module can be added to a rooftop or self-contained unit controller in the field for these reasons: The unit did not originally ship with a communication module. The unit originally shipped with a LONWORKS Communication Module but requires replacement with a BACnet Communication Module. Refer to Table 1 to determine whether or not changes are required to communication setup parameters. Note: McQuay MicroTech II ServiceTools software is required to modify these parameters. Call the McQuay Controls Customer Support group at 866-4MCQUAY for more information. Table 1. Factory Communication Setup Parameter Settings Parameter Name BACnet IP BACnet MSTP LON (DAC or SCC) No Communication Module lp Address IP Subnet Mask UDP Port Number IP Router Address IP Network Address MSTP Network Address MSTP MAC Address MSTP Baud Rate Communication Option None MSTP MSTP MSTP Device Instance Number 2 XXXXXX XXXXXX XXXXXX XXXXXX Max APDU Length Device Object Name 4 MTll RTUC XXXXXXXXX or MTII SCUC XXXXXXXXX MTll RTUC XXXXXXXXX or MTII SCUC XXXXXXXXX MTll RTUC XXXXXXXXX or MTII SCUC XXXXXXXXX MTll RTUC XXXXXXXXX or MTII SCUC XXXXXXXXX Important Notes 1. The BACnet MS/TP MAC Address is not adjustable from the MicroTech II ServiceTools; it is set via the dipswitch block on the MSTP communication module. 2. The Device Instance Number is factory set equal to the last six significant digits of the 18 digit number on the barcode label on the unit controller s main control board. For example, if the last six digits are , then the Device Instance Number is set to Whether or not this parameter is use by the systems integrator, it must be set to a unique value from all other controllers in the network. 3. The Max APDU Length parameter should not be set higher than 501 for BACnet MS/TP. 4. The Xs in Device Object Name are factory set equal to the last nine digits of the 18 digit number on the bar-code label on the unit controller s main control board. For example, if the last nine digits are , then the Device Object Name is set to MTII RTUC for an applied rooftop unit or MTII SCUC for a self-contained unit. Whether or not this parameter is use by the systems integrator, it must be set to a unique value from all other controllers in the network. IM

16 Service Information Troubleshooting If you can control the unit from the unit s keypad, but you are not able to communicate with unit via the network: Verify the network (bus) wiring. Verify the cable harness to the network terminals. Verify that the Transmit LED (DS2) is flickering. Verify that the MS/TP MAC address (SW1) is set in the range (Master). Check the network communication parameters in the unit controller for proper settings. Refer Configuring the Unit Controller section of this document for details. If the BACnet MS/TP Communication Module still does not respond, contact the McQuay Controls Customer Support group at 866-4McQuay ( ). Replacement Parts Contact the McQuay Parts group at for replacement parts related to the BACnet MS/TP Communication Module. McQuay does not supply the network connection plug. The three-contact network connection plug has custom graphics, but can be replaced with a standard network connector. The table below provides two manufacturers with the generic version of the network connection plug. Description Part Number Source BACnet MS/TP Communication Module installation kit (kit includes communication module, cable harness, and IM 704) McQuay Parts Cable harness McQuay Parts Connector plug (standard) Phoenix Contact Connector plug (standard) Altech Corp This document contains the most current product information as of this printing. For the most current product information, please go to All McQuay equipment is sold pursuant to McQuay's Standard Terms and Conditions of Sale and Limited Product Warranty McQuay International IM704-4