INT1G8xxBP Series Integrated Tap Installation Guide

Transcription

1 US LY WIT 250V US US LY WIT 250V US N POS N INT18xx Series Integrated Tap Installation uide To deploy the INT18xx ypass Tap into your network, simply: Unpack and install the INT18xx into any available 1U slot of a network rack and secure it with rack mount screws onnect the power supply to the INT18xx and plug it into an available power source Utilizing the onsole or IP switches, configure the INT18xx for the operating mode of your choice Remove the power supply to the INT18xx temporarily Using standard thernet cables, connect ports [] and [] (uto MI/MIX opper) of the INT18xx between the two live network devices where you would otherwise directly connect an inline appliance or sensor (IPS or LP). Verify network traffic is flowing, confirming that network cabling is correct onnect ports [] and [] (uto MI/MIX) to the primary inline IPS/LP appliance/sensor (or configure for other tools for traditional monitoring) onnect ports [] and [] (uto MI/MIX) to an optional secondary inline IPS/LP appliance/sensor (or configure for other tools for traditional monitoring) onnect ports [] and [] (uto MI/MIX) for additional monitoring capabilities. Ports may be setup for combined (aggregated) or directional (breakout) onnect the provided power leads to the INT18xx and plug them into an available power source Note: iber is always 1000Mbps speed. Other operating modes may be desired for monitoring and may be configured using the console or provided IP switches. IP switches will take precedence over console configuration Link ailure Propagation ypass Link/ctivity LP LP LP LP Network Primary Secondary Outputs Power Input 9 Serial IP Switches Power Input This document is for informational purposes only. The information in this document, believed by arland Technology to be accurate as of the date of publication, is subject to change without notice. arland Technology assumes no responsibility for any errors or omissions in this document and shall have no obligation to you as a result of having made this document available to you or based upon the information it contains. opyright 2012 arland Technology LL. ll Rights Reserved uffalo, New York arland, Texas

2 INT18xx Series Integrated Tap Installation uide INT18xx Tap Operating Modes Primary Sensor is ealthy and Passing Traffic Secondary Sensor is ealthy and Ready dditional Monitoring Outputs onfigured ual Inline ypass (uto) LP LP Network Sensor 1 Standby Outputs Primary Sensor is Offline Secondary Sensor is ctive and ealthy Monitoring Outputs Remain ual Inline ypass (Primary Offline) LP LP Network Offline Sensor 2 Outputs This document is for informational purposes only. The information in this document, believed by arland Technology to be accurate as of the date of publication, is subject to change without notice. arland Technology assumes no responsibility for any errors or omissions in this document and shall have no obligation to you as a result of having made this document available to you or based upon the information it contains. opyright 2012 arland Technology LL. ll Rights Reserved uffalo, New York arland, Texas

3 INT18xx Series Integrated Tap Installation uide INT18xx Tap Operating Modes Primary Sensor is ealthy and Passing Traffic ll Other Ports onfigured for Passive Monitoring Single Inline ypass + Monitoring LP LP Network Sensor Outputs Outputs Primary Sensor is ealthy and Passing Traffic Ports onfigured for reakout & ggregation Single Inline ypass + Monitoring LP LP Network Sensor Outputs Outputs This document is for informational purposes only. The information in this document, believed by arland Technology to be accurate as of the date of publication, is subject to change without notice. arland Technology assumes no responsibility for any errors or omissions in this document and shall have no obligation to you as a result of having made this document available to you or based upon the information it contains. opyright 2012 arland Technology LL. ll Rights Reserved uffalo, New York arland, Texas

4 INT18xx Series Integrated Tap Installation uide INT18xx Tap onfiguration Menus aud Rate: ata its: 8 Stop its: 1 Parity: None low ontrol: None Login: admin gtadmin1 Interface: Menu riven Select: 1. urrent Status 2. evice onfiguration 3. Username/Password 0. Logout 1. Tap Operation 2. Speed of Ports 3. Link ailure Propagation 4. Reverse ypass 5. Live Network uplex 6. eartbeat Parameters 7. ypass onfiguration urrent Status: Primary Inline Operating Mode: ual Inline evice Mode (Secondary ot Standby) Live Network Inline Sensor 1 Inline Sensor 2 Passive Outputs Port Port Port Port Port Port Port Port uto uto uto uto uto uto uto uto UP UP UP UP UP UP UP UP MISS MISS OO OO -> -> Select: 1. hange Username 2. hange Password eartbeat Rate: 15 /Sec eartbeats to miss before entering ypass: 15 Link ailure Propagation: nabled Reverse ypass: isabled Sticky Mode: isabled Press any key to continue: This document is for informational purposes only. The information in this document, believed by arland Technology to be accurate as of the date of publication, is subject to change without notice. arland Technology assumes no responsibility for any errors or omissions in this document and shall have no obligation to you as a result of having made this document available to you or based upon the information it contains. opyright 2012 arland Technology LL. ll Rights Reserved uffalo, New York arland, Texas

5 INT18xx Series Integrated Tap Installation uide INT18xx Tap onfiguration Menus 1. Tap Operation 2. Speed of Ports 3. Link ailure Propagation 4. Reverse ypass 5. Live Network uplex 6. eartbeat Parameters 7. ypass onfiguration 1. Number of Inline evices ttached to Unit 2. Sticky Mode onfiguration 3. Port onfiguration 4. Port onfiguration 5. Port onfiguration 6. Port onfiguration 7. ot or old Standby for Secondary IPS 1. Ports 2. Ports urrent Mode: nabled 1. nabled 2. isabled 0. pply Settings and Return urrent Mode: isabled 1. nable 2. isable (efault) 0. pply Settings and Return urrent Mode: uto 1. uto Negotiate (efault) 2. orce ull uplex (100 Mbit Only) 0. pply Settings and Return [6] eartbeat Parameters urrent eartbeat Rate is: ## /Sec nter new eartbeat Rate in /Sec (## to ###): ## urrent Number of heartbeats to miss is set to # nter Number of eartbeats to miss before entering ypass Mode: (# to ##): ## urrent Mode: uto ypass 1. orce Primary 2. orce Secondary 3. orce ypass (ypass LL IPS) 4. uto ypass (efault) 0. pply Settings and Return This document is for informational purposes only. The information in this document, believed by arland Technology to be accurate as of the date of publication, is subject to change without notice. arland Technology assumes no responsibility for any errors or omissions in this document and shall have no obligation to you as a result of having made this document available to you or based upon the information it contains. opyright 2012 arland Technology LL. ll Rights Reserved uffalo, New York arland, Texas

6 US LY WIT 250V US US LY WIT 250V US N POS N INT18xx Series Integrated Tap Installation uide Power Input 9 Serial IP Switches Power Input Speed uplex LP Rev ypass Pri IPS Only Sticky Mode ot Standby Use onsole 1000 UTO YS 100 ULL O O O O O NO IP Switch Options (requires power cycle) ypass or : mode that allows active temporary bypass of an IPS/LP type inline device. ypass based on the operating characteristics of the connected network appliance. When a bypass tap device is not able to detect link or heartbeats from (or through) inline appliances or sensors connecting to or tap sensor port pairs, the appliance is bypassed automatically, keeping link up and networks online and passing data. ggregation: ombines data flows for full-duplex monitoring on a single interface. Ideal when monitoring both sides of network traffic simultaneously. reakout: Separates data flows for half-duplex directional monitoring. Ideal when utilization is very high and packet loss is not an option. LP (Link ailure Propagation): llows link state to be mirrored to adjacent live network interfaces. When one side of a network loses link on a connecting tap, the link state is propagated to the other interface of the tap and ultimately to the other side of the network. nabled by default. (Link/ctivity): Solid when link is achieved and flashes when data is detected on an interface. ailsafe: On power loss, live network tap ports re-establish link with each other, resuming traffic flow between critical network devices. lways on. Sticky: If the primary sensor has been bypassed and the secondary is currently active, secondary will remain active even when the primary comes back online. If the secondary appliance goes offline, the primary will be used if it has link and is passing traffic in both directions. isabled by default. Reverse ypass: isables link on both live network ports if all inline appliances lose link or cannot pass traffic. isabled by default. This document is for informational purposes only. The information in this document, believed by arland Technology to be accurate as of the date of publication, is subject to change without notice. arland Technology assumes no responsibility for any errors or omissions in this document and shall have no obligation to you as a result of having made this document available to you or based upon the information it contains. opyright 2012 arland Technology LL. ll Rights Reserved uffalo, New York arland, Texas