HPE Intelligent Power Distribution Unit Installation Instructions

Transcription

1 HPE Intelligent Power Distribution Unit Installation Instructions Important safety information For important safety, environmental, and regulatory information, see Safety and Compliance Information for Server, Storage, Power, Networking, and Rack Products, available at the Hewlett Packard Enterprise website ( oducts). NOTE: The HPE Intelligent Power Distribution Unit (ipdu) is intended for use only with information technology equipment (ITE) loads in racks or similar computer room applications. Extension Bars ship with some kits. These Extension Bars are designed for use with Compaq/HPE Power Distribution Core Units and HPE Uninterruptible Power Systems (UPSs). The Extension Bars can be used with other power sources, provided that the source includes branch circuit overcurrent protection not exceeding 20. WRNING: To reduce the risk of personal injury from electric shock, do not remove the cover. There are no field-serviceable or user-serviceable components inside. WRNING: risk of personal injury from electric shock and hazardous energy levels exists. The installation of options and routine maintenance and service of this product must be performed by individuals who are knowledgeable about the procedures, precautions, and hazards associated with C power products. WRNING: The F900, F901 and F model PDUs must only be used on 240/415 circuits. 240/415 5 W wye power systems are not standardized in North merica and Japan and may be distributed using NEM L22 receptacles normally intended for 277/480 systems. To reduce the risk of fire and electric shock, be certain to connect the 415 models only to a receptacle wired for 240/415. Follow these safety precautions when connecting multiple hardware components to power sources. Copyright 2009, 2016 Hewlett Packard Enterprise Development LP The information contained herein is subject to change without notice. The only warranties for Hewlett Packard Enterprise products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. Hewlett Packard Enterprise shall not be liable for technical or editorial errors or omissions contained herein. Microsoft and Windows are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. WRNING: To reduce the risk of personal injury or damage to the equipment: Plug the input power cord into a grounded (earthed) electrical outlet that is located near the equipment and is easily accessible. Be sure that the load products connected to the Intelligent Power Distribution Unit (ipdu) are adjusted for, or otherwise capable of operation from the same line voltage supplying the ipdu. Failure to verify the voltage can lead to severe equipment damage. Do not overload the ipdu. The total input current of all equipment connected to each output cannot exceed the total output marked on the ipdu. Part Number: February 2016 Edition: 6

2 WRNING: To reduce the risk of personal injury from high-leakage current, verify earth connection before connecting the power supply. The summation of input power for multiple pieces of information technology equipment through the use of power products can result in high-leakage currents. If the total system leakage current for a system of components exceeds 3.5 m: The use of a detachable input power cord is prohibited. The input power cord must be securely attached, and it should be connected to the C mains by hardwiring or through the use of a non-residential, industrial-style plug that maintains positive earth connection. If the total system leakage current through the ground conductor exceeds 5% of the input current per line under normal ope conditions, the system loads should be divided among multiple power connections. Core Unit features Flexible mounting in 0U, 1U, or 2U configurations (depending on your, maximizing rack space (no additional parts are required for mounting) Overcurrent and short-circuit protection for each output (UL-489-listed circuit breakers) outlets to power Extension Bars, Intelligent Extension Bars, or other C20 plug-compatible equipment Easy identification and reset of overload circuits (circuit breakers move to Off position), minimizing downtime Power cord retention Recessed circuit breaker handles to prevent inadvertent power-off Core Unit components Overview These installation instructions are provided to assist qualified personnel with the installation of the Intelligent Power Distribution Unit (ipdu). IMPORTNT: The appearance of the ipdu might vary depending on the specific unit installed. The input voltage of a single ipdu is 200 to 240 C. The input voltage of a three ipdu is 200 to 240 C or 380 to 415 C, depending on the model. For more information about any of the topics covered in this document, and for safety information and regulatory notices, see the Intelligent Power Distribution Unit User Guide on the Hewlett Packard Enterprise website ( ipdu components Callout Description 1 Display Module 2 Core Unit 3 Extension Bar 4 Intelligent Extension Bar Callout Description 1 Circuit breaker for load segment 1 ( if 2 Circuit breaker for load segment 2 ( B if 3 Circuit breaker for load segment 3 ( C if 3 4 Circuit breaker for load segment 4 ( if 5 Circuit breaker for load segment 5 ( B if 6 Circuit breaker for load segment 6 ( C if 3 7 Serial connector for additional ipdu connection 8 Serial connector for Display Module connection 9 Network connector 10 Reset button* 11 outlet for load equipment power or Extension Bar attachment (load segment 6, C 12 outlet for load equipment power or Extension Bar attachment (load segment 5, B 13 outlet for load equipment power or Extension Bar attachment (load segment 4,

3 Callout Description 14 outlet for load equipment power or Extension Bar attachment (load segment 3, C 15 outlet for load equipment power or Extension Bar attachment (load segment 2, B 16 outlet for load equipment power or Extension Bar attachment (load segment 1, *When you press the Reset button, power to the outlets is maintained. Management functionality is momentarily lost while the components reset. 12-outlet Core Unit components Callout Description 1 Circuit breaker for load segment 7 ( if 2 Circuit breaker for load segment 8 ( B if 3 Circuit breaker for load segment 9 ( C if 3 4 Circuit breaker for load segment 10 ( if 3 5 Circuit breaker for load segment 11 ( B if 3 6 Circuit breaker for load segment 12 ( C if 3 7 Circuit breaker for load segment 1 ( if 8 Circuit breaker for load segment 2 ( B if 9 Circuit breaker for load segment 3 ( C if 3 10 Circuit breaker for load segment 4 ( if 11 Circuit breaker for load segment 5 ( B if 12 Circuit breaker for load segment 6 ( C if 3 13 outlet for load equipment power or Extension Bar attachment (load segment 12, C Callout Description 14 outlet for load equipment power or Extension Bar attachment (load segment 11, B 15 outlet for load equipment power or Extension Bar attachment (load segment 10, 16 outlet for load equipment power or Extension Bar attachment (load segment 9, C 17 outlet for load equipment power or Extension Bar attachment (load segment 8, B 18 outlet for load equipment power or Extension Bar attachment (load segment 7, 19 outlet for load equipment power or Extension Bar attachment (load segment 6, C 20 outlet for load equipment power or Extension Bar attachment (load segment 5, B 21 outlet for load equipment power or Extension Bar attachment (load segment 4, 22 outlet for load equipment power or Extension Bar attachment (load segment 3, C 23 outlet for load equipment power or Extension Bar attachment (load segment 2, B 24 outlet for load equipment power or Extension Bar attachment (load segment 1, 25 Reset button* 26 Network connector 27 Serial connector for Display Module connection *When you press the Reset button, power to the outlets is maintained. Management functionality is lost momentarily while the components reset. Display Module features Two-digit LED display that shows the current in each ipdu, load segment/extension Bar, or Intelligent Extension Bar outlet in tenths Three scroll buttons to scroll through values Two interior LEDs, which indicate power and alarms One exterior LED, which indicates normal operation During normal conditions, all ipdu component LEDs illuminate green. The blue UID illuminates on the Extension Bars to indicate which component corresponds to the current that appears on the Display Module.

4 Display Module components Intelligent Extension Bar components The total of the Intelligent Extension Bar is. Callout Description 1 LED numeric display for amperage of load segments/extension Bars and Intelligent Extension Bar outlets 2 LED numeric display for PDU current selection (display corresponds to PDU current) 3 LED numeric display for load segment/extension Bar current selection (display corresponds to load segment/extension Bar current) 4 LED numeric display for Intelligent Extension Bar outlet current selection (display corresponds to Intelligent Extension Bar outlet current) 5 Scroll button for Intelligent Extension Bar outlet current selection display (Outlet) 6 Scroll button for load segment/extension Bar current selection display (Ext Bar) 7 Scroll button for PDU current selection display (PDU) 8 Serial port for host computer connection 9 Serial port for Core Unit connection 10 Reset button* 11 larm LED 12 Power LED *When you press the Reset button, power to the outlets is maintained. Management functionality is momentarily lost while the components reset. Intelligent extension bar features (if included) Multiple power outlets, conveniently located for quick and easy equipment power connections Green power indicator for the Intelligent Extension Bar and each individual outlet Blue UID indicator for the component that corresponds to the current that appears on the ipdu Display Module Manual on/off control for each Intelligent Extension Bar, outlet, and outlet UID using the ipdu web interface ttached 2.4-m (8-ft) input power cords Callout Description 1 Row of green power indicators (one for each outlet) 2 Row of blue UID indicators (one for each outlet) 3 Row of five managed 10, C13 outlets 4 Row of outlet number identification labels (one for each outlet) Regardless of the installation orientation, the outlet closest to the top of the rack is always outlet number 1.* 5 Reset button** 6 Green power indicator for the Intelligent Extension Bar 7 Blue UID indicator for the Intelligent Extension Bar Not shown 2.4-m (8-ft) input power cord *If you change the orientation while the Intelligent Extension Bar is powered, you must press the extension bar's Reset button to apply the new outlet configuration. **When you press the Reset button, power to the managed outlets is maintained. Management functionality is momentarily lost while the Intelligent Extension Bar resets. Extension Bar features (if included) Multiple power outlets, conveniently located for quick and easy equipment power connections Green power indicator Blue UID indicator that illuminates when the Extension Bar current appears on the ipdu Display Module Manual on/off control for each Extension Bar UID using the ipdu web interface ttached 2.4-m (8-ft) input power cords Power cord retention Power cord retention

5 Extension Bar components The total of the Extension Bar is. Display Module (1) Serial cable (1) Core Unit cord retention bracket (1) Tie wraps Hardware mounting screws Extension Bar hardware (if included) This kit might contain extra pieces of hardware for your convenience. Callout Description 1 Five 10, C13 outlets 2 Green power indicator 3 Blue UID indicator m (8-ft) input power cord Kit contents Core Unit hardware 6-Outlet Core Unit: This document 0U mounting brackets (2) 1U mounting brackets (2) Display Module (1) Serial cable (2) Core Unit cord retention bracket (1) Tie wraps Hardware mounting screws 6-Outlet Core Unit with Extension Bars: This document 0U mounting brackets (2) 1U mounting brackets (2) Display Module (1) Serial cable (2) Core Unit cord retention bracket (1) Power cord retention brackets (4) Power cord retention bands Tie wraps Extension Bar hardware Hardware mounting screws 12-Outlet Core Unit: This document 2U mounting brackets (2) Model F531 F532 F534 INTL Number of Extension Bars Required tools Number of brackets Number of Extension Bar power cord retention bands Number of Core Unit tie wraps Phillips screwdriver T-25 Torx driver Cage nut insertion tool (included with your original rack hardware)

6 Installing the Core Unit Installing the Core Unit cord retention bracket The Core Unit cord retention bracket is shown for clarification in the following diagram, though installation of the Core Unit cord retention bracket is optional. Installing the 1U or 2U brackets The rack ears are reversible, so the ipdu can be installed with either the circuit breakers or the power cords facing forward. Two ipdus can be mounted in either a 1U or 2U configuration by mounting one ipdu in the front of the rack and the other ipdu in the rear of the rack. Installing the 0U brackets

7 Installing the Core Unit in the rack The Core Unit can be mounted in the rack two different ways, depending on whether you install the 0U brackets () or the 1U brackets (B) on the Core Unit. Installing the 1U or 2U Core Unit in a square-hole rail NOTE: Use the M6 screws and cage nuts that shipped with the rack when installing in a square-holed rail.

8 Installing the 0U Core Unit 3. ttach the provided screws through the holes on the perforated door. 4. Connect the serial cable to the serial connector on the Core Unit. Installing the Intelligent Extension Bars (if included) Intelligent extension bars are 5U in height and provide five outlets in a 5U space. IMPORTNT: Regardless of the installation orientation, the outlet closest to the top of the rack is always outlet number 1. If you change the orientation after initial installation, you must press the Reset button to apply the new outlet configuration. Installing the Display Module 1. Connect the serial cable to the PDU serial connector on the Display Module. 2. Install the Display Module on the inside of the rack door.

9 Installation of the cord retention bracket is optional. Installing the Extension Bars using a single configuration (if included) Extension bars are 5U in height and provide five outlets in a 5U space.

10 The cord retention bracket (1) is shown for clarification in the following diagram, though installation of the cord retention bracket is optional. The cord retention brackets (1) are shown for clarification in the following diagram, though installation of the cord retention brackets is optional. Installing the Extension Bars using a double configuration (if included) The double extension bar configuration provides ten outlets in a 5U space.

11 Connecting the ground bonding cable The ground bonding screw is provided as an attachment point for conductors. Use a ground bonding cable if the rack contains any conductors for the purpose of functional grounding or bonding of ungrounded metal parts. The ground bonding cable is not included in this kit. Connecting devices When connecting devices, distribute the loads evenly across the to remain within the capability of the Extension Bars and Core Unit. Do not overload the ipdu. The total current of all equipment connected to each output cannot exceed the total output marked on the ipdu. Connecting the ipdu to the power source WRNING: To prevent injury from electric shock or damage to the equipment: Plug the input line cord into a grounded (earthed) electrical outlet that is installed near the equipment and is easily accessible. Do not disable the grounding plug on the input line cord. The grounding plug is an important safety feature. Do not use extension cords. Connect the ipdu to a grounded utility power outlet. The C branch circuit overcurrent protection should be sized according to the standard of the plug configuration on each model. The maximum overcurrent for each model is listed in "Connecting devices ("Connecting the ipdu to the power source" on page 11)." Core Unit F520 F521 F522 F533 F523 F525 INTL Input of Core Unit 24 Single 40 Single Single Max branch circuit breaker Individual outlet and style per 50 per 60 per 32 circuit breaker oltage F526 INTL per F527 INTL per F F F538 INTL

12 Core Unit F900 N F901 N F902 N Input of Core Unit Max branch circuit breaker 20 per 30 per 30 per Individual outlet and style circuit breaker *For ipdus, each is defined as follows: Phase segments 1, 4, 7, and 10 Phase B segments 2, 5, 8, and 11 Phase C segments 3, 6, 9, and 12 oltage Server spatial ordering can be achieved by connecting the Intelligent Extension Bars numbering from the bottom of the rack. Insight Control power management v6.2 draws the servers in order based on this best practice so that only minimal arrangement is needed to place the servers in the actual U position in the rack. Extension Bar Total of Extension Bar Outlet style F528 C13 F547 Intelligent C13 Individual outlet 10 No 10 Yes Outlet monitor and control Extension Description Bar for ipdu -1 Power Feed Segment 1-2 Power Feed Segment 2-3 Power Feed Segment 3 Extension Description Bar for ipdu B B-1 Power Feed B Segment 1 B-2 Power Feed B Segment 2 B-3 Power Feed B Segment 3

13 Extension Description Bar for ipdu -4 Power Feed Segment 4-5 Power Feed Segment 5-6 Power Feed Segment 6 Extension Description Bar for ipdu B B-4 Power Feed B Segment 4 B-5 Power Feed B Segment 5 B-6 Power Feed B Segment 6 Checking the Display Module LED indicator Check that the LED indicator that is visible when the rack door is closed (1) illuminates or flashes. iewing current on the Display Module To view the current of ipdu components: 1. Press the Display Module button that corresponds to the component. o PDU Scrolls through the PDUs in the ipdu installation. For the 12-Outlet ipdu, the display shows: U Upper ipdu L Lower ipdu o LS Scrolls through the ipdu load segments/extension Bars in the ipdu installation. o Outlet Scrolls through the Intelligent Extension Bar outlets in the ipdu installation. On the 12-Outlet ipdu, outlets U1-6 correspond to outlets L7-12. The current selection displays in the LED numeric display above the corresponding button. NOTE: When a load segment has an Intelligent Extension Bar attached, the mps numeric LED display alternates between the load segment value and the outlet value. The Outlet numeric LED display simultaneously alternates between the outlet number and "-" to indicate the load segment total current. 2. Continue to press the button to scroll through the components until the display shows the desired current selection. The blue UID indicator illuminates on the Extension Bar or Intelligent Extension Bar outlet to indicate which current is displayed. Launching a terminal emulation program Connecting a host computer Connect a serial cable between the PC serial connector on the Display Module and the serial connector on a host computer. This connection is used to configure and access the ipdu through a terminal emulation program, as well as to upgrade the ipdu. CUTION: You cannot bypass the Display Module and connect a host computer directly to the ipdu. The host computer must be connected to the Display Module to ensure proper communication with the ipdu. Connecting the network cable Connect a standard Ethernet cable between the network connector on the Core Unit and a network jack. This connection is used to access the ipdu through telnet or the web interface. Checking the circuit breakers If power to a device is interrupted, check the circuit breakers and reset if necessary. If power is still not restored, contact your Hewlett Packard Enterprise authorized service representative. NOTE: HyperTerminal is the serial communication program provided with Microsoft Windows and is used in this section as an example for setting up a terminal emulation session. If you are using another utility, the steps might be different. 1. Be sure that you have connected a host computer. 2. On the host computer, click Start, and select Programs>ccessories>Communications>HyperTerminal. The Connection Description window appears. 3. Enter a description, select an icon for the connection, and then click OK. The Connect To window appears. 4. Select the serial connector on the host computer to which the serial cable is attached, and then click OK. The COM Properties window appears. 5. Select the following parameter values, and then click OK. o o o o o Bits per second Data bits 8 Parity None Stop bits 1 Flow control None

14 Configuring the ipdu for remote access 1. Be sure that you have connected a network cable to the Core Unit. IMPORTNT: The ipdu has a fixed setting to auto-negotiate the line speed and cannot be forced to a certain speed such as 10 Mbps or 100 Mbps. When connected to a network switch, the switch port must be set to auto-negotiate. uto-negotiation mode is the recommended industry standard setting and the ipdu will negotiate at the highest possible speed up to 100 / Full Duplex if the network switch supports this option. 2. Be sure that you have connected a serial cable to the Display Module and the host computer with an open terminal emulation session. 3. Press the Reset button on either the Display Module or the Core Unit. On the terminal emulation session screen running on the host computer, the POST executes, and the following prompt appears: Press any key in 5 seconds to enter the Service menu. 4. Press a key to enter the HPE Intelligent PDU Service Menu. 5. On the Service Menu, enter 1 at the prompt to select Module Configuration. The Intelligent PDU Main menu appears. Use the Main menu to configure the minimum settings required to access the ipdu remotely using telnet or the web interface. You can configure other settings using this menu in conjunction with a terminal emulation program or a telnet connection. 6. If your network includes a DHCP server, you can reserve the ipdu IP address using the information provided on the MC address label. -or- If your network is not configured with a DHCP server: a. On the Main menu, enter 1 at the prompt to open the Network Configuration submenu. b. Enter 1 at the prompt to open the IPv4 Network Configuration submenu. c. Enter 4 at the prompt, and then change the boot mode to static IP. d. Enter 1 at the prompt, and then enter the IP address of the ipdu. e. Enter 2 at the prompt, and then enter the subnet mask of the ipdu. f. Enter 3 at the prompt, and then enter the default gateway of ipdu. g. Enter 0 at the prompt to return to the Main menu. 7. Configure web access: a. On the Main menu, enter 1 at the prompt to open the Network Configuration submenu. b. Enter 4 at the prompt to open the Web ccess Configuration submenu. c. Use the submenu options to enable or disable web access, and then configure the associated port, if necessary. 8. Configure telnet access: a. On the Main menu, enter 1 at the prompt to open the Network Configuration submenu. b. Enter 3 at the prompt to open the Remote Console Configuration submenu. c. Use the submenu options to enable or disable telnet access, and then configure the associated port, if necessary. 9. Enter 0 at the prompt to return to the Main menu. 10. Enter 0 at the prompt to exit the configuration utility. 11. Enter s at the prompt to save the settings and close the configuration utility. ccessing the web interface CUTION: It is highly recommended that browser access to the ipdu is isolated from outside access using a firewall or isolated network. 1. Launch a supported browser. The browser window appears. 2. In the ddress field (Microsoft Internet Explorer) or the Location field (Mozilla and Firefox), enter: where xxx.xxx.xxx.xxx is the IPv4 or IPv6 address, and port is the HTTPS port. The default port is 443. The log in screen appears. 3. Enter the user name in the User Name field. The default user name is admin. 4. Enter the password in the Password field. The default password is admin. 5. Select the appropriate language in the Language dropdown box. 6. Click Sign In. The HPE Intelligent PDU web interface appears.