VP101-BT Installation Guide

Transcription

1 VP101-BT Installation Guide Package Contents 1 VP101-BT system unit 6 Mounting screws for Mini PCIe module 1 Quick Installation Guide 1 Disk includes: - Drivers / Manual Note: The CD that came with the system contains an autorun screen to install drivers, utilities, and software applications required to enhance the performance of the system and a user's manual for your reference. Insert the CD into a CD-ROM drive. The autorun screen will appear. If after inserting the CD, Autorun did not automatically start, please go directly to the root directory of the CD and double-click Setup. Please install all required drivers. DFI reserves the right to change the specifications at any time prior to the product's release. For the latest revision and details of the installation process, please refer to the user's manual. 1

2 Panel COM 4 (RS232) / 8-bit DIO CANbus (1) Antenna hole COM 1/2 (RS232/RS422/RS485) Power button (2) Top View USB 3.0 HDMI Reset switch/ Status LED LAN 2 VCC/ACC/GND (Connects to car battery) LAN 1 MIC-in Bottom View USB 2.0 VGA Line-out COM 5 (RS232) COM 3 (RS232/RS422/RS485) Note: 1. You can choose to wire the COM 4 port to be a CANbus (Controller Area Network) interface instead. 2. If the system's power-on or off is controlled by car ignition, please do not press the power-on/off button during the power-on or power-off process. 2

3 Removing the Chassis Cover Please observe the following guidelines and follow the procedure to open the system. 1. Make sure the system and all other peripheral devices connected to it have been powered off. 2. Disconnect all power cords and cables. 3. The 12 mounting screws on the bottom and two sides of the system are used to secure the cover to the chassis. Remove these screws and then put them in a safe place for later use. Chassis screw 4. After removing the mounting screws, lift the bottom side of the chassis cover to open the system. The Mini PCIe and the micro SD slots will be readily accessible. Mini PCIe slots micro SD 3

4 Installing a Mini PCIe Card The system board is equipped with 3 Mini PCIe slots: two full-size and one halfsize slots. Here we will demonstrate the installation of a half-size Mini PCIe card (PCIe/USB/LPC signals) for WiFi connection. 1. Grasp the Mini PCIe card by its edges and align the notch in the connector of the card with the notch in the connector on the system board. 2. Push the Mini PCIe card down and use the provided mounting screws to secure the card on the system board. Mounting screw Note: The system also has two additional full-size Mini PCIe slots that use PCIe (PCIe/ USB/3G/GPRS/CANbus signals) and msata (SATA signals) interfaces. 4

5 Installing a SATA Drive The system can accomondate one SATA drive. Please use the following procedure to install a SATA drive into the system. 1. SATA HDD bay is located under the power board. Please remove the power board first to uninstall the HDD bracket. Power board Power board Mounting screws SATA bracket Mounting screws 2. Install the SATA drive on the HDD bracket. Place the HDD bracket back to the system and secure the drive in place with the provided mounting screws. SATA connectors on the board SATA Mounting screws SATA connectors 5

6 Mounting Options VESA mount The VESA mount kit includes the following: 2 VESA mount brackets Bracket screws VESA mount bracket 1 VESA mount bracket 2 1. Select a place on the wall where you will mount the system. 2. Use the provided mounting screws to attach VESA mount bracket 1 to the wall. Mounting screw VESA mount bracket 1 6

7 3. Attach the other bracket (VESA mount bracket 2) to the rear of the system. Mounting screw VESA mount bracket 2 Mounting screw Hooks 4. Slide the system to "VESA mount bracket 1" to attach the two brackets with the hooks. Then tighten the screw to secure the assembly in place. Screw 7

8 Panel mount The panel mounting kit includes the following: 6 mounting clamps 1. Select a place on the panel (or wall) where you will mount the system. 2. Cut out a shape on the panel that corresponds to the system s rear dimensions (272mm x 169mm) and ensure that the system can be fitted into the panel properly. 5 Mounting hole Panel Insert the system from the outside surface of the panel into the mounting hole until it is properly fitted against the panel. 4. Position the mounting clamps along the rear edges of the system and insert them into the slits around the system. 8

9 White plastic cap Mounting clamp Slit for mounting the clamp 5. The first and second clamps must be positioned and secured diagonally prior to mounting the rest of the clamps. Tighten the clamp s screw using an electric screwdriver by pressing the white plastic cap onto the back of the panel. The illustration below shows that all clamps are properly mounted. 9

10 Board Layout and Jumper Settings JP (JP20) 1 (JP18) 1 (JP17) (JP21) COM 4/DIO Select (JP22, JP21) Digital I/O 4-7 Output State (JP18) Digital I/O 0-3 Output State (JP20) Digital I/O Power Select (JP17) Battery 1 Chassis Intrusion 1 COM 3 COM 4 COM 2 SPI Flash BIOS Buzzer Clear CMOS Data (JP24) 1 Standby Power LED Intel Atom SATA 2.0 E3800 Series SATA VGA ASMedia ASM1442 SATA Power emmc (optional) Nuvoton NCT6106D COM 1 Mini PCIe with LPC msata Mic-in Line-out USB 1 USB 2.0 ite IT8528E USB 2 MicroSD (optional) USB 0 USB 3.0 USB 0 System Fan Power 1 Select (JP5) COM Auto Power-on 9 Select (JP25) USB 6 USB 5-7 Power Select (JP7) USB 1-2 USB 7 Power Select (JP6) DC-in 1 1 from Power board LAN 1 Intel WGI210AT Intel WGI210AT SMSC USB4604 SIM Card HDMI NXP PTN3460 Reset LAN 2 Power Mini PCIe with SIM DC-in TOP BOTTOM USB Power Select: 0 (JP5), 1-2 (JP6), 5-7 (JP7) +5V_standby (default) 1-2 On +5V 2-3 On Auto Power-on Select Power-on via power button Power-on via AC power (default) JP On 2-3 On Clear CMOS Data Normal (default) Clear CMOS Data JP On 2-3 On Digital I/O Power Select JP17 +5V_standby 1-2 On +5V (default) 2-3 On JP18 (DIO 4-7) Digital I/O Output State JP20 (DIO 0-3) GND (default) 1-2 On +5V or +5V_standby 2-3 On COM 4/DIO Select COM 4 (default) DIO JP21, JP22 1-2, , On 2-3, , On Note: You cannot use COM 4 and DIO at the same time. Please adjust JP21 and JP22 together. 10

11 Delay Turn-on/off Switch The DIP switch (SW1) on the power board can be used to turn on or off the system at a specific on/off delay time via car ignition. SW1-2: System-on delay enable/disable On (Default) Off Enable (delay time setting adjustable by SW1-4 and 1-5 as shown in the table below) Disable (System-on delay = 3 sec) SW1-4 and 1-5: System-on delay time setting 4 5 Time On On 10 sec (default) Off On 30 sec On Off 1 min Off Off 5 min SW1-3: System-off delay enable/disable On (Default) Off Enable (delay time setting adjustable by SW1-6, 1-7 and 1-8 as shown in the table below) Disable (System-off delay = 0 sec) SW1-6, 1-7 and 1-8: System-off delay time setting Time On On On 30 sec (default) Off On On 1 min On Off On 3 min Off Off On 5 min On On Off 10 min Off On Off 15 min On Off Off 30 min Off Off Off 1 hr Note: The OS will start the shut-down procedure after the car ignition switches off. Please make sure that system-off delay time is sufficient to allow the OS to shut down completely. 11 A