Solid State Package $ Effective June 1, 2015 Prices Subject to Change without Notice

Transcription

1 TM TM Raising the Bar for Automotive Service Professionals W. 183 rd St. Olathe, KS Phone: Web: automotive-technics.com TM TM Solid State Package $ Effective June 1, 2015 Prices Subject to Change without Notice NOTE: The Solid State Package is used in conjunction with the Start-Up Package. Qty Part No. Name Description Transistor Board #1 NTE123AP, TO92 Case Transistor Board #2 NTE159,TO92 Case Transistor Board #4 NTE263 Darlington NPN, TO220 Case Transistor Board #6 NTE66, MOSFET N-Channel, TO220 Case Voltage Regulator 5V, TO220 Case. Board # SCR Board #1 Silicon Controlled Rectifier, TO220 Case GM Remote Lamp Driver Board GM Check Engine Lamp Driver Module GM Dimmer Module Board Dash Lamp Control Motor Board #2 Typical Power Mirror Motor Individual Patch Cord 18 AWG X 12 test lead wire, stackable banana plugs w/setscrew, (Yellow). Color may vary Dual Banana Plug Stackable w/setscrews for component mounting. (Yellow). Color may vary Resistor Assortment 350 1/2W carbon-film resistors K 100K Potentiometer Board Heavy duty 2W pot M 1M Potentiometer Heavy duty 2W pot. Board 1 CD Contains worksheets and information sheets pertaining to Solid State Package. Copyright 2015 T. J. Smalldon 1 SolidState15.pub

2 Transistor Board #1 $42.00 Part No. 033 Description: NTE123AP Bipolar NPN transistor, TO92 case. Transistor plugs into socket for easy replacement in the event of damage. Banana jacks spaced to accommodate a dual banana plug in five different positions. Transistor Board #2 $42.00 Part No. 034 Description: NTE159 Bipolar PNP transistor, TO92 case. Transistor plugs into socket for easy replacement in the event of damage. Banana jacks spaced to accommodate a dual banana plug in five different positions. Transistor Board #4 $45.00 Part No. 036 Description: NTE263 Bipolar NPN Darlington transistor, TO220 case. 10A, 65W. Internal suppression diode across collector and emitter. Also two internal resistors in base circuits. Banana jacks spaced to accommodate a dual banana plug in five different positions. Transistor Board #6 $49.00 Part No. 037 Description: NTE66 MOSFET N-Channel transistor, TO220 case. 12A, 75W. Banana jacks spaced to accommodate a dual banana plug in five different positions. Copyright 2015 T. J. Smalldon 2 SolidState15.pub

3 Voltage Regulator Board #1 $46.00 Part No. 038 Description: 5V regulator, 1A. Banana jacks spaced to accommodate a dual banana plug in five different positions. This regulator can be configured as an adjustable voltage regulator. It can also be configured as a current regulator, current boost regulator and the previous with short circuit protection. SCR Board #1 $44.00 Part No. 039 Description: Silicon Controlled Rectifier. Application: latching switch in security systems. Banana jacks spaced to accommodate a dual banana plug in five different positions. GM Lamp Driver Board $79.00 Part No. 040 Description: Operates various computer service lamps. Good example of small signal transistor switch. Transistor normally ON. Turns OFF with low signal input (typically from computer). Leads labelec according to GM wiring diagram. Supported with information sheet. GM Dimmer Module Board $92.00 Part No. 041 Description: Operates instrument cluster lamps. NPN power transistor. This is an amplifier application. Leads labeled according to GM wiring diagram. Supported with information sheet. Copyright 2015 T. J. Smalldon 3 SolidState15.pub

4 100K Potentiometer Board $56.00 Part No K Description: Heavy duty 100KΩ, 2W potentiometer. Fourth banana jack accommodates dual banana jack with resistor, etc. in five different positions. Eliminates need for additional Universal Board to accommodate dual banana plug w/resistor. 1M Potentiometer Board $56.00 Part No M Description: Heavy duty 1MΩ, 2W potentiometer. Fourth banana jack accommodates dual banana jack with resistor, etc. in five different positions. Eliminates need for additional Universal Board to accommodate dual banana plug w/resistor. Mirror Motor Board #2 $51.00 Part No. 044 Description: Typical of motor found in most vehicle exterior rearview mirrors. Flag on motor shaft helps detect rotation and direction. Jumpers $6.00 Part No Description: 12 test lead wire. Stackable banana plugs are secured with set screws permitting repair if necessary. Four yellow jumpers supplied in Solid State Package. Copyright 2015 T. J. Smalldon 4 SolidState15.pub

5 Resistor Assortment $15.00 Part No. 057 Description: Five each of the 70 most popular values, 350 total. All 1/2W carbon film resistors. All resistors are listed on the Resistor Ohm/Color Chart Information Sheet supplied on the Elector Set CD. Dual Banana Plug Blank #1 $4.00 Part No Description: Stackable. Components secured through side holes with set screws in bottom of jacks. Polarity option indicated by tab marked NEG. Protrusion off to side with hole originally intended for lead strain relief but also works nicely for mounting components. Available colors indicated in part number by dashed suffix: 0 Blk, 1 Brn, 2 Red, 3 Orn, 4 Yel, 5 Grn, 6 Blu, 7 Vlt, 8 Gry, 9 Wht. Worksheets $ Value Part No. 000 Description: Worksheets pertain to boards included in the Solid State Package. They are in Microsoft Word format on a CD. There is a blank student worksheet and an instructor answer worksheet with comments for each suggested circuit. The worksheet format can be used to create your own worksheets. The worksheets were created as fill-in-the-form format which makes them suitable for use on computer also. Information Sheets $60.00 Value Part No. 000 Description: Information sheets pertain to boards included in the Solid State Package. They are in PDF format in one PDF file on a CD. It is suggested that they be printed in color and laminated for use with each board setup. An economical method for laminating is to use clear transparent Con-Tact brand self adhesive laminate. Most of the information sheets are marked for cutting at 5 X 8. Copyright 2015 T. J. Smalldon 5 SolidState15.pub

6 Sample Solid State Circuit #1 Description: Transistor switch circuit. This circuit uses the Transistor Board #1 to operate a #194 bulb (from Start-Up Package). The transistor base current is turned on and off by a toggle switch (from Start-Up Package). Sample Solid State Circuit #2 Description: Transistor amplifier circuit. This circuit uses the Transistor Board #4 to operate an 1157 bulb (from Start-Up Package) stop lamp filament. The transistor base current is controlled by the 100KΩ Potentiometer Board. The result is a lamp dimmer circuit. Copyright 2015 T. J. Smalldon 6 SolidState15.pub

7 Copyright 2015 T. J. Smalldon 7 SolidState15.pub