Datasheet G156BGE-L03. Cover Lens. Bezel Touch Sensor. Bonding/Optical/Tape. Embedded Board/ AD Driving solution. TFT display

Size: px

Start display at page:

Download "Datasheet G156BGE-L03. Cover Lens. Bezel Touch Sensor. Bonding/Optical/Tape. Embedded Board/ AD Driving solution. TFT display"

Chrystal Montgomery
5 years ago
Views:

Cover Lens Bezel Touch Sensor Embedded Board/ AD Driving

TFT display Backlight Driver Housing Computer-on-Module

If you require a touch panel and/or mechanical

1 Cover Lens Bezel Touch Sensor Embedded Board/ AD Driving solution Storage Wireless Software Bonding/Optical/Tape TFT display Backlight Driver Housing Computer-on-Module Memory More Value! If you require a touch panel and/or mechanical integration, please scan the QR code or click the URL /products/displays/colour-tft-displays/ Datasheet G56BGE-L3

2 Doc. Number Tentative Specification Preliminary Specification Approval Specification MODEL NO. G56BGE SUFFIX L3 Customer APPROVED BY SIGNATURE Name / Title Note Please return copy for your confirmation with your signature and comments. Approved By Checked By Prepared By 瑩 Version. 8 November 26 / 26 The copyright belongs to InnoLux. Any unauthorized use is prohibited.

3 CONTENTS. GENERAL DESCRIPTION...5. OVERVIEW GENERAL SPECIFICATIONS MECHANICAL SPECIFICATIONS ABSOLUTE MAXIMUM RATINGS ABSOLUTE RATINGS OF ENVIRONMENT ELECTRICAL ABSOLUTE RATINGS TFT LCD MODULE BACKLIGHT CONVERTER ELECTRICAL SPECIFICATIONS FUNCTION BLOCK DIAGRAM INTERFACE CONNECTIONS ELECTRICAL CHARACTERISTICS LCD ELETRONICS SPECIFICATION Vcc Power Dip Condition BACKLIGHT UNIT BACKLIGHT PIN ASSIGNMENT BACKLIGHT PIN ASSIGNMENT LVDS INPUT SIGNAL SPECIFICATIONS LVDS DATA MAPPING TABLE COLOR DATA INPUT ASSIGNMENT DISPLAY TIMING SPECIFICATIONS POWER ON/OFF SEQUENCE OPTICAL CHARACTERISTICS TEST CONDITIONS OPTICAL SPECIFICATIONS RELIABILITY TEST ITEM PACKING MODULE LABEL PRECAUTIONS ASSEMBLY AND HANDLING PRECAUTIONS STORAGE PRECAUTIONS OPERATION PRECAUTIONS SAFETY PRECAUTIONS SAFETY STANDARDS Version. 8 November 26 2 / 26 The copyright belongs to InnoLux. Any unauthorized use is prohibited.

4 9.6 OTHER Outline Drawing Version. 8 November 26 3 / 26 The copyright belongs to InnoLux. Any unauthorized use is prohibited.

5 REVISION HISTORY Version Date Page Description. Oct.3, 26 All Spec Ver.. was first issued. Version. 8 November 26 4 / 26 The copyright belongs to InnoLux. Any unauthorized use is prohibited.

6 . GENERAL DESCRIPTION. OVERVIEW G56BGE-L3 is a 5.6 TFT Liquid Crystal Display module with LED Backlight unit and 3 pins ch-lvds interface. This module supports 366 x 768 WXGA mode and can display up to 6.7M colors. The LED driving device for Backlight is built in PCBA..2 GENERAL SPECIFICATIONS Item Specification Unit Note Screen Size 5.6 real diagonal Driver Element a-si TFT active matrix - - Pixel Number 366 x R.G.B. x 768 pixel - Pixel Pitch.252 (H) x.252 (V) mm - Pixel Arrangement RGB vertical stripe - - Display Colors 6.7M color - Transmissive Mode Normally white - - Surface Treatment AG type, 3H hard coating, - - Luminance, White 5 Cd/m2 Color Gamut 65 % of NTSC(Typ.) - - Power Consumption 2. W Max 2. MECHANICAL SPECIFICATIONS Item Min. Typ. Max. Unit Note Horizontal (H) mm Module Size Vertical (V) mm Thickness (T) mm Bezel Area Horizontal mm Vertical mm Active Area Horizontal mm Vertical mm Weight g Version. 8 November 26 5 / 26 The copyright belongs to InnoLux. Any unauthorized use is prohibited.

7 3. ABSOLUTE MAXIMUM RATINGS 3. ABSOLUTE RATINGS OF ENVIRONMENT Item Symbol Value Min. Max. Unit Note Storage Temperature TST -2 6 () Operating Ambient Temperature TOP 6 (), (2) Note () (a) 9 %RH Max. (Ta < 4 ). (b) Wet-bulb temperature should be 39 Max. (Ta < 4 ). (c) No condensation. Note (2) The temperature of panel surface should be min. and 65 max. 3.2 ELECTRICAL ABSOLUTE RATINGS 3.2. TFT LCD MODULE Item Symbol Value Min. Max. Unit Power Supply Voltage Vcc V Logic Input Voltage V IN V Note () BACKLIGHT CONVERTER Item Symbol Value Min. Typ Max. Unit Note Converter Voltage LED_V in 2 8 V (), (2) Enable Voltage LED_EN V Duty=% Backlight Adjust LED_PWM V (), (2) Pulse Width msec. and Duty % Note () Permanent damage to the device may occur if maximum values are exceeded. Function operation should be restricted to the conditions described under Normal Operating Conditions. Note (2) Specified values are for input pin of LED light bar at Ta=25±2 (Refer to and for further information). Version. 8 November 26 6 / 26 The copyright belongs to InnoLux. Any unauthorized use is prohibited.

8 4. ELECTRICAL SPECIFICATIONS 4. FUNCTION BLOCK DIAGRAM RX(+/-) RX(+/-) RX2(+/-) RX3(+/-) RXC(+/-) NC GND Vcc CONVERTER CONNECTOR CONVERTER Version. 8 November 26 7 / 26 The copyright belongs to InnoLux. Any unauthorized use is prohibited.

9 4.2. INTERFACE CONNECTIONS PIN ASSIGNMENT Pin Name Description NC Not connection, this pin should be open. 2 NC Not connection, this pin should be open. 3 NC Not connection, this pin should be open. 4 GND Ground 5 RX- Negative LVDS differential data input. Channel 6 RX+ Positive LVDS differential data input. Channel 7 GND Ground 8 RX- Negative LVDS differential data input. Channel 9 RX+ Positive LVDS differential data input. Channel GND Ground RX2- Negative LVDS differential data input. Channel 2 2 RX2+ Positive LVDS differential data input. Channel 2 3 GND Ground 4 RXCLK- Negative LVDS differential clock input. 5 RXCLK+ Positive LVDS differential clock input. 6 GND Ground 7 RX3- Negative LVDS differential data input. Channel 3 8 RX3+ Positive LVDS differential data input. Channel 3 9 GND Ground 2 NC Not connection, this pin should be open. 2 NC Not connection, this pin should be open. 22 NC Not connection, this pin should be open. 23 GND Ground 24 GND Ground 25 GND Ground 26 Vcc +5V power supply 27 Vcc +5V power supply 28 Vcc +5V power supply 29 Vcc +5V power supply 3 Vcc +5V power supply Note () Connector Part No. MSCK247P3.D(STM) Note (2) The first pixel is odd. Note (3) Input signal of even and odd clock should be the same timing. Version. 8 November 26 8 / 26 The copyright belongs to InnoLux. Any unauthorized use is prohibited.

10 4.3 ELECTRICAL CHARACTERISTICS 4.3. LCD ELETRONICS SPECIFICATION Parameter Symbol Value Min. Typ. Max. Unit Note Power Supply Voltage Vcc V - Ripple Voltage V RP mv - Rush Current I RUSH A (2) White A (3)a Power Supply Current Black A (3)b Vertical Stripe A (3)c Power Consumption PLCD Watt (4) LVDS differential input voltage Vid 2 6 mv (5) LVDS common input voltage Vic..2.4 V (5) LVDS terminating resistor R T ohm Note () The ambient temperature is Ta = 25 ± 2. Note (2) Measurement Conditions Version. 8 November 26 9 / 26 The copyright belongs to InnoLux. Any unauthorized use is prohibited.

11 Note (3) The specified power supply current is under the conditions at Vcc = 5. V, Ta = 25 ± 2, Fr = 6Hz, whereas a power dissipation check pattern below is displayed. Note (4) The power consumption is specified at the pattern with the maximum current. Note (5) VID waveform condition Version. 8 November 26 / 26

12 4.3.2 Vcc Power Dip Condition BACKLIGHT UNIT Value Parameter Symbol Unit Min. Typ. Max. Converter Power Supply Voltage LED_Vin V Converter Power Supply Current Ii.8..2 A Power Consumption P LED.5 W EN Control Level Backlight on LED_EN Backlight off.8 PWM Control Level PWM High Level LED_PWM PWM Low Level.5 V PWM Control Duty Ratio -- % PWM Control Frequency f PWM 9 2 2k Hz V 2V LED_Vin = 2V Duty=% LED Life Time L L 5, Hrs (2) Note () LED light bar input voltage and current are measured by utilizing a true RMS multimeter as shown below Note (2) The lifetime of LED is defined as the time when LED packages continue to operate under the conditions at Ta = 25 2 and I= 7 ma (per chip) until the brightness becomes 5% of its original value. Input Power PLED Power Supply Vin, Ii GND Converter LED Backlight Unit Version. 8 November 26 / 26

13 4.3.4 BACKLIGHT PIN ASSIGNMENT Pin Symbol Description Remark V i Converter input voltage 2V 2 V GND Converter ground Ground 3 EN Enable pin 3.3 V 4 ADJ Backlight Adjust PWM Dimming (Hi 3.3 V DC, Lo V DC ) 5 NC Not Connect Note () Connector Part No.CI425M2HRP-NH,CVILUX 4.4 LVDS INPUT SIGNAL SPECIFICATIONS 4.4. LVDS DATA MAPPING TABLE LVDS Channel LVDS output D7 D6 D4 D3 D2 D D Data order G R5 R4 R3 R2 R R LVDS Channel LVDS output D8 D5 D4 D3 D2 D9 D8 Data order B B G5 G4 G3 G2 G LVDS Channel 2 LVDS output D26 D25 D24 D22 D2 D2 D9 Data order DE NA NA B5 B4 B3 B2 LVDS Channel 3 LVDS output D23 D7 D6 D D D5 D27 Data order NA B7 B6 G7 G6 R7 R6 Version. 8 November 26 2 / 26

14 Version. 8 November 26 3 / COLOR DATA INPUT ASSIGNMENT The brightness of each primary color (red, green and blue) is based on the 8-bit gray scale data input for the color. The higher the binary input, the brighter the color. The table below provides the assignment of color versus data input. Data Signal Red Green Blue Color R7 R6 R5 R4 R3 R2 R R G7 G6 G5 G4 G3 G2 G G B7 B6 B5 B4 B3 B2 B B Basic Colors Black Red Green Blue Cyan Magenta Yellow White Gray Scale Of Red Red() / Dark Red() Red(2) Red(253) Red(254) Red(255) Gray Scale Of Green Green() / Dark Green() Green(2) Green(253) Green(254) Green(255) Gray Scale Of Blue Blue() / Dark Blue() Blue(2) Blue(253) Blue(254) Blue(255) Note () Low Level Voltage, High Level Voltage

15 4.5 DISPLAY TIMING SPECIFICATIONS The input signal timing specifications are shown as the following table and timing diagram. Signal Item Symbol Min. Typ. Max. Unit Note Frequency Fc MHz - Period Tc 3.5 ns Input cycle to cycle jitter T rcl -.2*Tc.2*Tc ns (3) Input Clock TLVCCS -.2*Tc.2*Tc ns (4) LVDS Clock Vertical Display Term Horizontal Display Term to data skew Spread spectrum modulation range Spread spectrum modulation frequency Fclkin_ mod FC*98% FC*2% MHz F SSM 2 KHz Frame Rate Fr Hz Tv=Tvd+Tvb Total Tv Th - Active Tvd Th - Display Blank Tvb Th - Total Th Tc Th=Thd+Thb Active Display Thd Tc - Blank Thb Tc - Note () Because this module is operated by DE only mode, Hsync and Vsync input signals are ignored. Note (2) The Tv(Tvd+Tvb) must be integer, otherwise, this module would operate abnormally. (5) INPUT SIGNAL TIMING DIAGRAM Version. 8 November 26 4 / 26

16 Note (3) The input clock cycle-to-cycle jitter is defined as below figures. Trcl = I T TI Note (4) Input Clock to data skew is defined as below figures. Note (5) The SSCG (Spread spectrum clock generator) is defined as below figures. Version. 8 November 26 5 / 26

17 4.6 POWER ON/OFF SEQUENCE The power sequence specifications are shown as the following table and diagram. Timing Specifications Parameter Value Min Typ Max Units T.5 - ms T2-5 ms T3-5 ms T ms T ms T ms T7 5-3 ms T8 - - ms T9 - - ms T ms Note () Please avoid floating state of interface signal at invalid period. Note (2) When the interface signal is invalid, be sure to pull down the power supply of LCD VCC to V. Note (3) The Backlight converter power must be turned on after the power supply for the logic and the interface signal is valid. The Backlight converter power must be turned off before the power supply for the logic and the interface signal is invalid. Version. 8 November 26 6 / 26

18 5. OPTICAL CHARACTERISTICS 5. TEST CONDITIONS Item Value Unit Ambient Temperature (Ta) 25±2 Ambient Humidity (Ha) 5± %RH Supply Voltage Input Signal LED Light Bar Input Current Per Input Pin o C According to typical value in "ELECTRICAL CHARACTERISTICS" 5.2 OPTICAL SPECIFICATIONS The relative measurement methods of optical characteristics are shown in 5.2 and all items are measured at the center point of screen except white variation. The following items should be measured under the test conditions described in 5. and stable environment shown in Note (5). Color Chromaticity (CIE 93) Item Symbol Condition Min. Typ. Max. Unit Note Rx.627 Red Ry.339 Green Blue White Center Luminance of White (Center of Screen) Contrast Ratio Gx.328 Gy Typ.59 Bx θ x =, θ Y =.45.6 CS-2 By.63 R=G=B=255 Wx Gray scale.33 Wy.329 Typ (), (5) L C cd/m 2 (4), (5) CR (2), (5) T R Response Time θ T x =, θ Y = ms (3) F White Variation W θ x =, θ Y = % (5), (6) Horizontal θx- + θx Viewing Angle CR Deg. (), (5) Vertical θy- + θy Version. 8 November 26 7 / 26

19 Note () Definition of Viewing Angle (θx, θy) Note (2) Definition of Contrast Ratio (CR) The contrast ratio can be calculated by the following expression. Contrast Ratio (CR) = L255 / L L255 Luminance of gray level 255 L Luminance of gray level CR = CR (5) CR (X) is corresponding to the Contrast Ratio of the point X at Figure in Note (6). Note (3) Definition of Response Time (T R, T F ) Version. 8 November 26 8 / 26

20 Note (4) Definition of Luminance of White (L C ) Measure the luminance of gray level 255 at center point L C = L (5) L (x) is corresponding to the luminance of the point X at Figure in Note (6). Note (5) Measurement Setup The LCD module should be stabilized at given temperature for 4 minutes to avoid abrupt temperature change during measuring. In order to stabilize the luminance, the measurement should be executed after lighting Backlight for 4 minutes in a windless room. Note (6) Definition of White Variation (δw) Measure the luminance of gray level 255 at 9 points δw = ( Minimum [L () ~ L (9)] / Maximum [L () ~ L (9)] ) *% Version. 8 November 26 9 / 26

21 6. RELIABILITY TEST ITEM Items Required Condition Note High Temperature Storage 6, 24hours ()(2) Low Temperature Storage -2, 24hours ()(2) Thermal Shock Test -2 /3min, 6 / 3min, cycles ()(2) High Temperature Operation 6, 24hours ()(2) Low Temperature Operation, 24hours ()(2) High Temperature & High Humidity Operation Test Vibration Test (Non-operation) Shock Test (Non-operation) ESD (Electro Static Discharge) 6, RH 9%, 24 hours ()(2) Acceleration.5 Grms (3) Wave Half-sine Frequency - 3 Hz Sweep 3 Minutes each Axis (X, Y, Z) Acceleration 5 G (3) Wave Half-sine Active Time ms Direction ± X, ± Y, ± Z.(one time for each Axis) Contact Discharge ± 8KV, 5pF(33Ω) () Air Discharge ± 5KV, 5pF(33Ω) () Note () criteria Normal display image with no obvious non-uniformity and no line defect. Note (2) Evaluation should be tested after storage at room temperature for more than two hour Note (3) At testing Vibration and Shock, the fixture in holding the module has to be hard and rigid enough so that the module would not be twisted or bent by the fixture. The fixing condition is shown as below Version. 8 November 26 2 / 26

22 7. PACKING 7. PACKING SPECIFICATIONS () 3 pcs LCD modules / Box (2) Box dimensions 465 (L) X 362 (W) X 34 (H) mm (3) Weight approximately 2Kg (3 modules per box) 7.2 PACKING METHOD Figure. 7- Packing Version. 8 November 26 2 / 26

23 Sea / Land Transportation (4ft Container) Air Transportation Figure. 7-2 Packing 7.3 UN-PACKING METHOD Figure. 7-3 UN-Packing Version. 8 November / 26

24 8. MODULE LABEL. INX MODULE LABEL The barcode nameplate is pasted on each module as illustration, and its definitions are as following explanation. G56BGE-L3 E27943 XXXXXXXYMDXNNNN RoHS (a) Model Name G56BGE-L3 Revision Rev. XX, for example A, B, C, C2 etc. (c) Factory ID (d) Serial ID X X X X X X X Y M D X N N N N Serial INX Internal Use Year, Month, Date INX Internal Use Revision INX Internal Use Serial ID includes the information as below (a) Manufactured Date Year ~9, for 2~29 Month ~9, A~C, for Jan. ~ Dec. Day ~9, A~Y, for st to 3 st, exclude I, O and U (b) Revision Code cover all the change (c) Serial No. Manufacturing sequence of product Version. 8 November / 26

25 9. PRECAUTIONS 9. ASSEMBLY AND HANDLING PRECAUTIONS () Do not apply rough force such as bending or twisting to the module during assembly. (2) To assemble or install module into user s system can be only in clean working areas. The dust and oil may cause electrical short or worsen the polarizer. (3) It s not permitted to have pressure or impulse on the module because the LCD panel and Backlight will be damaged. (4) Always follow the correct power sequence when LCD module is connecting and operating. This can prevent damage to the CMOS LSI chips during latch-up. (5) Do not pull the I/F connector in or out while the module is operating. (6) Do not disassemble the module. (7) Use a soft dry cloth without chemicals for cleaning, because the surface of polarizer is very soft and easily scratched. (8) It is dangerous that moisture come into or contacted the LCD module, because moisture may damage LCD module when it is operating. (9) High temperature or humidity may reduce the performance of module. Please store LCD module within the specified storage conditions. ()When ambient temperature is lower than may reduce the display quality. For example, the response time will become slowly. 9.2 STORAGE PRECAUTIONS () Do not leave the module in high temperature, and high humidity for a long time. It is highly recommended to store the module with temperature from to 35 and relative humidity of less than 7% (2) Do not store the TFT LCD module in direct sunlight (3) The module should be stored in dark place. It is prohibited to apply sunlight or fluorescent light in storing 9.3 OPERATION PRECAUTIONS () The LCD product should be operated under normal condition. Normal condition is defined as below Temperature 2±5 Humidity 65±2% Display pattern continually changing pattern(not stationary) (2) If the product will be used in extreme conditions such as high temperature,high humidity,high altitude,display pattern or operation time etc It is strongly recommended to contact INNOLUX for application engineering advice. Otherwise, Its reliability and function may not be guaranteed. 9.4 SAFETY PRECAUTIONS () If the liquid crystal material leaks from the panel, it should be kept away from the eyes or mouth. In case of contact with hands, skin or clothes, it has to be washed away thoroughly with soap. (2) After the module s end of life, it is not harmful in case of normal operation and storage. Version. 8 November / 26

26 9.5 SAFETY STANDARDS The LCD module should be certified with safety regulations as follows () UL695- or updated standard. (2) IEC695- or updated standard. 9.6 OTHER When fixed patterns are displayed for a long time, remnant image is likely to occur. Version. 8 November / 26

27 . Outline Drawing Version. 8 November / 26

28 Offices DACH (Germany, Austria, Switzerland) Avnet EMG GmbH Gruber Straße 6d Poing Phone Denmark Avnet Integrated Solutions Avnet Nortec A/S Lyskær Herlev Phone Fax denmark_integrated@avnet.eu Finland Avnet Integrated Solutions Avnet Nortec Oy Pihatörmä B 224 Espoo Phone Fax finland_integrated@avnet.eu France Avnet Integrated Solutions Avnet EMG France SA Parc Club du Moulin à Vent, Bât 33, rue du Dr Georges Lévy Vénissieux Cedex Phone Fax lyon_integrated@avnet.eu Avnet Integrated Solutions Avnet EMG France SA 4 avenue Carnot 9349 Massy Cedex Phone Fax paris_integrated@avnet.eu Avnet Integrated Solutions Avnet EMG France SA Les Peupliers II 35 avenue des Peupliers 355 Cesson-Sévigné Phone Fax rennes_integrated@avnet.eu Israel Avnet Israel st Avnet Road 465 Tel Mond Phone daniel.katz@avnet.eu Italy Avnet Integrated Solutions Avnet EMG Italy SRL Via Manzoni, Cusano Milanino Phone Fax milano_integrated@avnet.eu South Africa Avnet South Africa (Johannesburg) Block 3, Pinewood Office Park, 33 Riley Road, Woodmead P.O. Box 3853, Rivonia, 228, South Africa Phone Fax sales@avnet.co.za Avnet South Africa (Cape Town) Ground Floor, Forrest House, Belmont Office Park, 4 Belmont Road, Rondebosch P.O. Box 34, Mowbray, 775, South Africa Phone Fax sales@avnet.co.za Avnet South Africa (Durban) 22 Clemsford, 2 nd, Essex Gardens, Nelson Road, Westville P.O. Box 428, Wandsbeck, 363, South Africa Phone Fax sales@avnet.co.za Sweden (Norway) Avnet Integrated Solutions Avnet Nortec AB Löfströms Allé Sundbyberg Phone Fax sweden_integrated@avnet.eu United Kingdom (Ireland) Avnet Integrated Solutions 5a Waltham Park White Waltham Maidenhead Berkshire, SL6 3TN Phone Fax uk_integrated@avnet.eu All trademarks and logos are the property of their respective owners. This document provides a brief overview only, no binding offers are intended. No guarantee as to the accuracy or completeness of any information. All information is subject to change, modifications and amendments without notice. 6/27

SPECIFICATION G156BGE-L TFT - WXGA - LVDS. Version: 2.0 Date:

SPECIFICATION G156BGE-L TFT - WXGA - LVDS. Version: 2.0 Date: SPECIFICATION G56BGE-L 5.6 TFT - WXGA - LVDS Version 2. Date 3.3.27 Note This specification is subject to change without prior notice www.data-modul.com Doc. Number Tentative Specification Preliminary