IQView8/ Touch Screen Display

Transcription

1 Touch Screen Display Important: Retain these instructions These instructions shall be used by trained service personnel only If the equipment is used in a manner not specified by these instructions, the protection provided by the equipment may be impaired. Contents Unpacking... Storing... Installation.... Installation - Mounting.... Installation - On a Wall...4. Installation - In a Dry Partition Wall Installation - Power up Installation - Wiring Installation - Connect Cables End User Licence greement... 5 Cleaning and Maintenance... 6 Disposal... Unpacking Storing (ltitude: <000 m (656 )) IQView8 Installation Instructions (TG0) -0 C (-4 F) +70 C (58 F) H O 0 85 %RH up to 40 C (04 C) Installation WRNING Do not attempt to open the unit. Failure to comply may cause damage to the unit. Labels used on IQView8 RX+ RX- TX+ TX C NO NC Service button Connector for Trend current loop network Connector for relay output Memory card slot It is recommended that the installation should comply with the local electrical safety installation practices (e.g. HSE Memorandum of Guidance on Electricity at Work Regulations 989, US National Electric Code). USB connector RJ (FCC68) connector for connection Ethernet connector /dc Connector for /dc input power. C power line return. Installation - Mounting Dimensions continued over page IQView8 (with mounting brackets) 55 mm (0.0") 9 mm (9.4") 0.0 mm (9.05") 48 mm (.88") 7.7 mm (.48") 0 mm (.9") IQVIEW8 SURFCE MOUNTING BOX (Surface Mounting) 4.5 mm (9.6") 46.5 mm (.8") 90 mm (.54") 75 mm (6.9") 0.5 mm (8") IQView8 TG0 Issue, 0-pr-0

2 . Installation- Mounting (continued) Dimensions (continued) Mounting Requirements IQVIEW8 DRY PRTITION WLL BOX (In Wall Mounting) 0 mm (8.66") 60 mm (.6") 70 mm (6.7") Unit is UL rated as UL96 listed open energy management equipment. Operating ltitude: <000 m (656 ) -0 C (+4 F) +60 C (+40 F) H O C (04 C) 0 %RH 85 %RH up to 40 Remove Connectors Important: Keep connectors 4 Check Gasket is in Position 5 Select Mounting Method If panel mounting step 6 If surface mounting section. If in wall mounting section. IQView8 TG0 Issue, 0-pr-0

3 . Installation- Mounting (continued) 6 Prepare Panel to 5mm (0.08 to 0. ) 8.4 mm (0. ) mm (8.8 ) 0 mm (0.8 ) Cutout for display 48 mm (5.8 ) 75 mm (6.89 ) 8.6 mm (0.7 ) 5 mm (.8 ) Inside panel for connections 0 mm (9.05 ) 7 Mount Unit Click 4 8 Wire Connectors 9 Connect Cables Installation - Wiring on page 9 Installation - Connect Cables on page 0 Close Panel Power up IQView8 Installation - Power up on page 8 IQView8 TG0 Issue, 0-pr-0

4 . Installation - On a Wall Requires IQVIEW8 SURFCE MOUNTING BOX sold seperately. Remove Gasket Remove Drill Outs (if required) Ø = mm (0.87 ) Prepare Mounting Points UK Double Pattress Box, US Double Pattress Box, or flat surface Either UK Double Pattress Box Fit pattress box 4.5 mm (9.6") or US Double Pattress Box Fit pattress box 4.5 mm (9.6") 0.5 mm (8") 0.5 mm (8") or Flat Surface Mark hole positions 4.5 mm (9.6 ) 60 mm (6. ) Drill holes and insert plugs 4 holes Ø = 5 mm (0.0 ) 50 mm (5.9 ) 0.5 mm (8 ) 60 mm (6. ) continued over page 4 IQView8 TG0 Issue, 0-pr-0

5 . Installation - On a Wall (continued) Prepare Mounting Points (continued) UK Double Pattress Box, US Double Pattress Box, or flat surface 4 Mount Enclosure UK Double Pattress Box, US Double Pattress Box, or flat surface or Flat Surface (continued) Insert top screws mm (0. ) Either UK Double Pattress Box or US Double Pattress Box or Flat Surface 5 Route Cables Using Drill outs If routing cables through the drill outs run the cables to into the enclosure using 0 mm gable glands (not supplied). or Either into Rear of enclosure If routing cables from a pattress box run the cable to the pattress box as required, and then into the rear of the enclosure. 6 Wire Connectors Installation - Wiring on page 9 7 Connect Cables Installation - Connect Cables on page IQView8 TG0 Issue, 0-pr-0 5

6 . Installation- On a Wall (continued) 8 Mount IQView8 into Enclosure Click 9 Fit ccess Lid 0 Power up IQView8 Installation - Power up on page 8. Installation - In a Dry Partition Wall Requires IQVIEW8 DRY PRTITION WLL BOX sold separately Prepare Wall mm (0.475 ) inside wall mm (8.74 ) 6.6 mm (0.6 ) 9.5 to 5 mm (0.5 to 0.98 ) 55 mm (.7 ) Cutout for display 65 mm (6.5 ) 75 mm (6.89 ) 5 mm (.8 ) inside wall for connectors 0 mm (9.05 ) 6 IQView8 TG0 Issue, 0-pr-0

7 . Installation - In a Dry Partition Wall (continued) Remove Gasket Mount Chassis Loosen locking screws 4 places Insert chassis in hole djust brackets 4 places Tighten adjustment screws Tighten locking fixing screws 4 places 4 places 4 Route Cables Either into Rear of Chassis or Bottom Edge or Top Edge Cables can be routed inside the wall and into the rear of the chassis. Cables can be routed inside the wall and through the bottom edge of the chassis. IQView8 TG0 Issue, 0-pr-0 7

8 . Installation - In a Dry Partition Wall (continued) 5 Wire Connectors 6 Connect Cables Installation - Wiring on page 9 Installation - Connect Cables on page 7 Mount IQView8 into Chassis 8 Power up IQView8 Click Installation - Power up on page 8.4 Installation - Power up Read Licence Switch On section O Read and agree to the end user licence agreement see, section. I Check LEDs 4 Configure IQView8 Configuration Manual (TE0) Normal Operation Fault Power Orange Check power supply 8 IQView8 TG0 Issue, 0-pr-0

9 .5 Installation - Wiring Wire Relay Connector - (if required for alarm notification) C rating: 60 V. e.g 0 Important: Orientate connector as shown. DC rating: 60 W. e.g. 40 Vdc 4 Do not connect 0V input power to this connector Terminal size 0.5 to.5 mm (0 to 4 WG) Note that for UL rating CU only cable must be used. On when larm present (Relay energised) rc suppression recommended. Relay Output rc Suppression (TG0008) On when larm not present (Relay off) C NO NC C NO NC Vac Power Supply - + 4Vac Power Supply Load Load Wire Current Loop (if required for network connection) Polarity independent Terminal size 0.5 to.5 mm (4 to 0 WG) 4 wire R R T T RX+ RX- TX+ TX Important: Orientate connector as shown. X T T R R Cable Belden 98 Belden 907 Trend TP//// HF/00 (Belden 876) Trend TP//// HF/00 (Belden 87) wire k baud R R 4k8 baud 9k6 baud 700 m ( m (545 RX+ RX- TX+ TX X 9k baud 700 m ( m ( m (80 50 m (70 T T No. of Wires IQView8 TG0 Issue, 0-pr-0 9

10 Installation - Wiring (continued) Wire Power Connector Important: Orientate connector as shown. ±5% 50/60 Hz at 0 V minimum or 4 Vdc 440 m, 0.5 W. For dc a dc supply with a minimum output of 600 m is recommended. O I DO NOT SWITCH ON POWER Do not connect 0V input power to this connector. Terminal size 0.5 to.5 mm (0 to 4 WG) Note that for UL rating the input power connections must be made using 8 WG or larger wire rated at least 90ºC. WRNING: This apparatus must be earthed (grounded) via input supply earth (ground) terminal. The earth (ground) on this unit is NOT a protective earth (ground), but it is essential that an earth is fitted for functional reasons. Input power supply: The 4V supply must include a suitably rated switch in close proximity and be clearly marked as the disconnecting device for the unit. General Connections /dc 0 Vac/ transformer with isolated output (e.g. Blue CC/4VC) /dc Note the required power cannot be provided by a controller s auxiliary supply output; a separate supply is required. 0 Vac/ transformer with one side earthed (grounded). /dc For US/Canada use a UL Listed, Class, 4 Vac transformer 4 Vdc /dc 0 V 4 Vdc E N L 0 Vac For US/Canada use a UL Listed, Class, transformer E N L For US/Canada use a UL Listed, Class, transformer Some transformers are earthed (grounded) on one side of the secondary. If so ensure the earthed (grounded) side is connected to the central terminal of the power connector. If the polarity of the connection is incorrect the unit will not power up. If this happens swap the connections to the right ( ) and central ( ) terminals..6 Installation - Connect Cables Connect Relay Output (if required for alarm notification) Do not connect 0V input power to this connector rc suppression recommended. Relay Output rc Suppression (TG0008) Terminal size 0.5 to.5 mm (0 to 4 WG) 0 IQView8 TG0 Issue, 0-pr-0

11 Installation - Connect Cables (continued) Connect Network Cable Connect to Ethernet, Current Loop or Either Ethernet or Current Loop m (09 RJ45 RJ45 Ethernet hub/switch or IQ Controller Ethernet socket Note that when connected to an IQ controller s Ethernet socket the controller s vcnc must be set up or CBLE/ EJ0565 RJ CBLE/ EJ05650 IQ, IQ4 IQxx IQxx with RJ CNCs IQxx with 5 Way D type CBLE/78-7 IQxx with 5 Way in-line Connecting to IQ4, IQ, IQxx, or IQxx with RJ connector CNCs, oriqxx with 5 Way D type connector IQxx with 5 way in-line connector Cable Required RJ to RJ cable with a twist (CBLE/EJ05650). RJ to 5 way D type cable (CBLE/EJ0565). RJ to 5 Way D type cable (CBLE/EJ0565) and 5 way D type socket to 5 in-line adapter cable (CBLE/78-7). IQView8 TG0 Issue, 0-pr-0

12 Installation - Connect Cables (continued) Connect Power Cable O I DO NOT TURN ON POWER Do not connect 0V input power to this connector. WRNING: This apparatus must be earthed (grounded) via input supply earth (ground) terminal. The earth (ground) on this unit is NOT a protective earth (ground), but it is essential that an earth is fitted for functional reasons. /dc Input power supply: The 4V supply must include a suitably rated switch in close proximity and be clearly marked as the disconnecting device for the unit. 4 End User Licence greement You have acquired an IQView8 ( Device ) that includes software licensed by Trend Control Systems Ltd from one or more software licensors ( Trend Control Systems Ltd Software Suppliers ). Such software products, as well as associated media printed materials and online or electronic documentation ( SOFTWRE ) are protected by international intellectual property laws and treaties. The SOFTWRE is licensed, not sold. ll rights reserved. IF YOU DO NOT GREE TO THIS END USER LICENSE GREEMENT ( EUL ), DO NOT USE THE DEVICE OR COPY THE SOFTWRE. INSTED, PROMPTLY CONTCT Trend Control Systems Ltd FOR INSTRUCTIONS ON RETURN OF THE UNUSED DEVICE(S) FOR REFUND. NY USE OF THE SOFTWRE INCLUDING BUT NOT LIMITED TO USE ON THE DEVICE will constitute your agreement to the EUL (or Ratification of any previous consent). GRNT OF SOFTWRE LICENSE. This EUL grants you the following license: You may use the SOFTWRE only on the DEVICE NOT FULT TOLERNT. THE SOFTWRE IS NOT FULT TOLERNT. Trend Control Systems Ltd HS INDEPENDENTLY DETERMINED HOW TO USE THE SOFTWRE IN THE DEVICE, ND Trend Control Systems Ltd s software suppliers HS RELIED UPON Trend Control Systems Ltd TO CONDUCT SUFFICIENT TESTING TO DETERMINE THT THE SOFTWRE IS SUITBLE FOR SUCH USE. NO WRRNTIES FOR THE SOFTWRE. THE SOFTWRE is provided S IS and with all faults. THE ENTIRE RISK S TO STISFCTORY QULITY, PERFORMNCE, CCURCY, ND EFFORT (INCLUDING LCK OF NEGLIGENCE) IS WITH YOU. LSO, THERE IS NO WRRNTY GINST INTERFERENCE WITH YOUR ENJOYMENT OF THE SOFTWRE OR GINST INFRINGEMENT. IF YOU HVE RECEIVED NY WRRNTIES REGRDING THE DEVICE OR THE SOFTWRE, THOSE WRRNTIES DO NOT ORIGINTE FROM, ND RE NOT BINDING ON, Trend Control Systems Ltd s software suppliers. No Liability for Certain Damages. EXCEPT S PROHIBITED BY LW, Trend Control Systems Ltd s software suppliers SHLL HVE NO LIBILITY FOR NY INDIRECT, SPECIL, CONSEQUENTIL OR INCIDENTL DMGES RISING FROM OR IN CONNECTION WITH THE USE OR PERFORMNCE OF THE SOFTWRE. THIS LIMITTION SHLL PPLY EVEN IF NY REMEDY FILS OF ITS ESSENTIL PURPOSE. IN NO EVENT SHLL Trend Control Systems Ltd s software suppliers BE LIBLE FOR NY MOUNT IN EXCESS OF U.S. TWO HUNDRED FIFTY DOLLRS (U.S.$50.00). Limitations on Reverse Engineering, Decompilation, and Disassembly. You may not reverse engineer, decompile, or disassemble the SOFTWRE, except and only to the extent that such activity is expressly permitted by applicable law notwithstanding this limitation. SOFTWRE TRNSFER LLOWED BUT WITH RESTRICTIONS. You may permanently transfer rights under this EUL only as part of a permanent sale or transfer of the Device, and only if the recipient agrees to this EUL. If the SOFTWRE is an upgrade, any transfer must also include all prior versions of the SOFTWRE. 5 Cleaning and Maintenance There are no serviceable parts inside the unit. Cleaning of the unit should be carried out in order to avoid buildup of dust or other contaminents. Disconnect power before carrying out any cleaning. Clean surfaces with a cloth moistened with water. 6 Disposal WEEE Directive: t the end of their life the packaging, and product should be disposed of by a suitable recycling centre. Do not dispose of with normal household waste. Do not burn. Please send any comments about this or any other Trend technical publication to techpubs@trendcontrols.com 0 Honeywell Technologies Sàrl, ECC Division. ll rights reserved. Manufactured for and on behalf of the Environmental and Combustion Controls Division of Honeywell Technologies Sàrl, Z.. La Pièce, 6, 80 Rolle, Switzerland by its uthorized Representative, Trend Control Systems Limited. Trend Control Systems Limited reserves the right to revise this publication from time to time and make changes to the content hereof without obligation to notify any person of such revisions or changes. Trend Control Systems Limited lbery House, Springfield Road, Horsham, West Sussex, RH PQ, UK. Tel:+44 (0) Fax:+44 (0) Trend Control System US th venue NE, Redmond, Washington 9805, US. Tel:(45) Fax:(45) IQView8 TG0 Issue, 0-pr-0