GUIDE TO MIU/7 1-10V CONVERTER INTERFACE UNIT
|
|
- Kelly Phillips
- 5 years ago
- Views:
Transcription
1 IMPORTANT The data highway cable, (Belden 9729 or 9730) must be segregated from any mains wiring. The casing of this unit must not be drilled or modified in any way. (For cable entry, knockouts have been provided at the top and bottom of the unit casing). Failure to comply with these instructions will invalidate all warranties stated or implied. MIU/7 The installation of this equipment should only be attempted by a competent qualified electrician. There is a risk of exposure to live mains and it is the installers responsibility to ensure that the supply to the unit is safe before removing covers or opening doors to the equipment. The installation can be carried out without the need to work on exposed live electronics. If in any doubt, contact Polaron for further advice. 1
2 INTRODUCTION The MIU/7 converts a dimmed output to a 1-10V signal and switched mains. It is generally used in a situation where a 4 or 12 channel Millennium rack is supplied, but one channel of 1-10V is required. Note that this unit does not work with a Compact rack due to the filtering components around the power semiconductor. The compact rack has 1-10V available on each channel.the MIU7 will also accept 0-5V or 0-10V inputs and convert to 1-10V with a switched mains output. The 1-10V output will also source current for use with some theatre scroller motors (300mA maximum output at 10V). The output can be reversed for 10-0V for use with metal halide fibre optic projectors. COMPATIBLE DEVICES MSD Lighting Control Units MCP Control Plates MTS LCD Touchscreen MIU/1 Multiplexor MIU/2 RS232 Gateway Interface Unit MIU/3 Multi-purpose Interface Unit MIU/4 24 inputs & 8 output Interface Unit MIU/8 Dial-in Interface Unit MIU/9 Star wiring Interface MIP/2 Intelligent Infra-red Controller MIP/3 Hand-held Infra-red programmer/ controller MIP/4 Hand-held Infra-red controller MOS/1 Lightlink Dimmer Manager Software GUARANTEE All products are covered by a 1 year Return to Base guarantee for parts and labour. Site visits are not covered by this guarantee and will normally result in a call out charge if such a visit is requested or deemed necessary. Although we have endeavoured to make this manual as comprehensive as possible, it does not cover every aspect of every possible system installation. Please feel free to call our Customer Care Department if you have any questions on tel: or service@polaron.co.uk 2
3 The lightlink System An overview The Polaron dimming system in its simplest form consists of 2 components, a dimmer panel and a control device (generally a control plate). The dimmer panel and control plate are connected by a data cable. BELDEN 9729 / 9730 cable or equivalent is recommended. This cable allows the dimmer panel and control plate to communicate with each other. It is called the datahighway and it carries data messages between the microprocessor in the control device and the Lightlink Scene Processor (LSP) module in the dimmer panel using an RS485 protocol. The datahighway cable consists of 2 twisted pairs with individual screens. One pair carries the data (S+, S-) and the other pair the low voltage power (+24V, 0V). The following layout shows a more complex system. Any combination of Polaron products can be seamlessly linked on the data highway to form a system which is fully customised to meet Client specification. 3
4 TECHNICAL INFORMATION 4
5 LOCATION The interface unit can be installed almost anywhere. However, it should not be installed under water pipes, sprinklers, near to sources of large electro-magnetic fields such as air-conditioning motor assemblies or in areas where the ambient temperature is likely to exceed 40 o C. The unit should be easily accessible for maintenance. MOUNTING The unit should be mounted on a flat surface. Keyholes for fixing screw location are provided at the four corners of the unit. Dimensions of the unit showing cable entry locations 5
6 INSIDE UNIT - LOCATION OF KEY COMPONENT PARTS Maximum adjustment Offset adjustment Relay threshold adjustment Input connections Mains Power Fuse Control Circuit Fuse. Output connections Signal input Mains supply Load switched output 1-10V output to ballast 0-5 input if required 6
7 MAINS INPUT CONNECTION WIRING Connection to the mains supply is made at the 2- part connector on the left hand side of the pcb. Only pins 3, 4 and 5 are used. A mains cable with a maximum diameter of 1.5mm 2 is recommended. MIU/7 location of 2-part mains input connector in unit Connection wiring diagram 7
8 SCHEMATIC FAULT FINDING WARNING! For fault finding it will be necessary to remove the front of the unit, exposing live mains supply. If you have concerns about doing this, please return the unit to Polaron for testing. There are two fuses located on the LSP card, the mains power fuse is located on the left hand side of the board and the data highway power protection fuse which is located on the right side of the board (see page 6). These should be tested first, after which the wire connections should all be checked. If the unit is still faulty, please return it to Polaron for further testing. 8
9 INSTALLER NOTES 9
10 POLARON PRODUCT INFORMATION / FAX BACK SHEET PLEASE LEAVE THIS INSTALLATION GUIDE WITH THE USER/CLIENT IF YOU EXPERIENCE ANY PROBLEMS WITH THE UNIT, PLEASE FAX THIS COMPLETED SHEET TO: +44 (0) Information to be completed when unit is installed: Client Name: Installation Name & Address: Date of Installation: Installer s Name: Job Number: Product Serial Number: Any Other Comments / Information: If you experience any problems with the unit, please detail them in the box below and fax your completed sheet back to the number above: 10
11 FOR FURTHER INFORMATION Please contact us at the following: Polaron Controls Ltd 26 Greenhill Crescent Watford Business Park Watford Hertfordshire WD18 8XG UK Main Switchboard Tel: +44 (0) Main Switchboard Fax: +44 (0) Website: Customer Care: +44 (0)
SCD96 DMX Output Interface. Installation guide
SCD96 DMX Output Interface Installation guide Contents Introduction 2 Welcome 2 Dimensions 2 Specification 2 Safety 3 Please read this first 3 Mounting 4 Location and spacing 4 Ambient atmosphere requirements
More informationDLA. DMX512 Analyzer. DLA Users Manual SV2_00 B.lwp copyright ELM Video Technology, Inc.
DLA DMX512 Analyzer DLA DLA-HH 1 Table Of Contents IMPORTANT SAFEGUARDS... 2 DLA OVERVIEW... 3 CONNECTION... 3 OPERATION... 3 HARDWARE SETUP... 4 DLA-HH (PORTABLE) LAYOUT... 4 CHASSIS LAYOUT... 4 DLA MENU
More informationLight Source User Guide
Light Source User Guide Vega Slimline Plastic Light Source Range Models covered by this manual: UFO VEGA SLP-2700M UFO VEGA SLP-3000M UFO VEGA SLP-4000M UFO VEGA SLP-2700DMX UFO VEGA SLP-3000DMX UFO VEGA
More informationDBC1220GL. 12 x 20A HF Ballast Controller Installation Manual. contents
DBC1220GL 12 x 20A HF Ballast Controller Installation Manual contents Warning.. 2 Hardware Controls... 7 Features.. 2 Troubleshooting. 8 Important Safeguards.. 2 Specification.. 8 Internal View.. 3 Mounting.
More informationETC Installation Guide
Unison Foundry Overview The Unison Foundry provides fully-rated 20A relays for switched power control with 0 10V dimming for compatible fluorescent ballasts and LED drivers. The provides two outputs of
More informationDCM Digital Control Modules
DCM Digital Control Modules TECHNICAL MANUAL Version 1.2 November 2011 Safety Precautions Caution Read Instructions: Read and understand all safety and operating instructions before using the equipment.
More informationLighting Systems. DALI Lighting Network Solutions. For comfortable, intelligent, efficient buildings
Lighting Systems DALI Lighting Network Solutions For comfortable, intelligent, efficient buildings DALI Product Range DINrail Mount DALI Controllers 4 Loop Addressable DALI Controller 4 Loop DALI controller
More informationVega Decorative Light Source Range
Light Source User Guide Vega Decorative Light Source Range Models covered by this manual: UFO VEGA - CM UFO VEGA - TM UFO VEGA - MCM UFO VEGA - MTM UFO VEGA - CDMX UFO VEGA - TDMX UFO VEGA - C 0-10V UFO
More informationFibre Modem - Single-mode
Revision 1.0 November. 2006 1 - Single-mode P/N: : 995087 Model 3000 / Access 4000 Optically Isolated Interface INSTALLATION GUIDE OVERVIEW: The Inner Range Single-mode provides 2 separate, optically isolated
More informationDTE x 10A Trailing Edge Dimmer Installation Manual. contents
DTE310 3 x 10A Trailing Edge Dimmer Installation Manual contents Warning.. 2 Features.. 2 Important Safeguards.. 2 Internal View.. 3 Mounting. 4 Supply & Load Cable Connections. 5 Connecting Serial Control
More informationUser Manual. JS-ICON 624 PACK Portable Dimmer Pack. JOHNSON SYSTEMS INC. Spring
User Manual JS-ICON 624 PACK Portable Dimmer Pack JOHNSON SYSTEMS INC. Spring 2007 Table of Contents JS-ICON 624 DMX JS-ICON 624 CC 6-2.4kW Dimming Strip JS-ICON 624 ND 6-2.4kW Relay Strip Introduction...3
More informationSTUDIO 1800 OPERATING INSTRUCTIONS MANUFACTURED IN THE UK
STUDIO 1800 OPERATING INSTRUCTIONS MANUFACTURED IN THE UK The Studio 1800 is a combined Programmer and Temperature Controller which has been specifically designed for use with pottery kilns. Control of
More informationDBC x 10A HF Ballast Controller Installation Manual
DBC1210 12 x 10A HF Ballast Controller Installation Manual contents Warning.. 2 Hardware Controls... 7 Features.. 2 Troubleshooting. 8 Important Safeguards.. 2 Specification.. 8 Internal View.. 3 Mounting.
More informationMAXIMA+ Series Rotary Level Indicator
MAXIMA+ Series Rotary Level Indicator BinMaster: Division of Garner Industries 7201 N. 98th St., Lincoln, NE 68507 402-434-9102 email: info@binmaster.com www.binmaster.com OPERATING INSTRUCTIONS PLEASE
More informationLASERMET SLIMJIM LED SIGN INSTRUCTION MANUAL LEDS-SJ XXX
LASERMET SLIMJIM LED SIGN INSTRUCTION MANUAL LEDS-SJ 00843-00-XXX 00843-53-000 Page 1 of 11 Issue 3 2 January 2013 Lasermet SlimJim Illuminated Sign Instruction Manual Contents Introduction... 4 Installation...
More informationInstruction Manual. Contents
SceneSelect II Scene-setting and Dimming System SBD410 HF BALLAST CONTROLLER Instruction Manual Warning... 2 Features... 2 Important Safeguards... 2 Internal View......3 Mounting... 4 Supply & Load Cable
More informationTwo Door Controller GEN-045
Australian Owned, Designed and Manufactured Two Door Controller GEN-045 Genesis Electronics Australia Pty Ltd www.genesiselectronics.com.au Distributed by: Genesis reserves the right to change or modify
More informationKNX T-UP. Temperature Sensor. Technical specifications and installation instructions
EN KNX T-UP Temperature Sensor Technical specifications and installation instructions Elsner Elektronik GmbH Control and Automation Engineering Herdweg 7 D 75391 Gechingen Phone +49 (0) 70 56 / 93 97-0
More informationMAXIMA + Series ROTARY LEVEL CONTROL
Price $5.00 MAXIMA + Series ROTARY LEVEL CONTROL OPERATING INSTRUCTIONS PLEASE READ CAREFULLY Division of Garner Industries 7201 North 98th Street Lincoln, NE 68507-9741 (402) 434-9102 925-0268 Rev. A
More informationIMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW ALL SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION IMPORTANT SAFETY INSTRUCTIONS WARNING RISK OF SEVERE INJURY OR DEATH To reduce the risk of death,
More information5 B&W Rear View System Camera
5 B&W Rear View System Camera Instruction Manual MODEL: CA453 www.lorexcctv.com Copyright 2007 LOREX Technology Inc. Thank you for purchasing the Lorex 5 Black & White Rear View System Camera. This system
More informationResolver to Digital Expansion Board
Resolver to Digital Expansion Board Catalog No. EXB009A01 Installation and Operating Manual 6/98 MN1313 Table of Contents Section 1 General Information............................. 1-1 Introduction....................................
More informationPull Cord Time Delay Switch 3-wire version
PCTDS3 energy saving controls Product Guide Pull Cord Time Delay Switch 3-wire version today, tomorrow and in the future Issue 3.0 Product Overview The PCTDS3 Pull Cord Time Delay Switch provides timed
More informationRako RAK-4F Instruction Manual. Overview
Rako RAK-4F Instruction Manual Overview The Rako RAK-4 system is designed for use as a single 4 channel switch/dimmer pack or to be joined together to give 8, 12 or a maximum 16 channel dimmer stack (4
More informationAB0602D ARCHITECTURAL BALLAST DRIVER. Version Date 06/25/2012
AB0602D ARCHITECTURAL BALLAST DRIVER Version 0.10 Date 06/25/2012 Page 2 of 10 DESCRIPTION AND FEATURES The AB-0602D is a 6 circuit, 2400 Watts per circuit ballast driver intended for dimmable fluorescent
More informationsmar Specifications and information are subject to change without notice. Up-to-date address information is available on our website.
smar www.smar.com Specifications and information are subject to change without notice. Up-to-date address information is available on our website. web: www.smar.com/contactus.asp PS302P - Fieldbus Power
More informationSOLOdrive AC, 100W, DALI, 1 control channel, constant current, 4x 57V outputs, side feed, square metal
100W DALI 'Dim to Dark' LED Driver SOLOdrive SOLOdrive offers industry-best Natural Dimming to dark - LED dimming made beautiful! With any dimmer, in any application. Symbiosis on SOLOdrive stands for
More informationSystem Installation guide
System Installation guide Ligo System installation guide V3 newestpage 1 of 14 Contents 1 INTRODUCTION... 3 2 SYSTEM TOPOLOGY... 3 3 CONTROL ELEMENTS... 4 3.1 LIGO CONTROLLERS... 4 3.2 IP DOMAIN... 5 3.3
More informationTOXALERT MODEL AIR 2000
TOXALERT MODEL AIR 2000 NOTE: Toxalert s Model GVU-CO 2 Sensor is the same as the Air2000R. Microprocessor-based, Infrared Environmental CO 2 Sensor OPERATOR S MANUAL TOXALERT TM INTERNATIONAL INC. P.O.
More informationADVANCED MICRO SYSTEMS
Overview... 3 Included in the Box:... 3 Pinout... 4 Installation... 5 Power Supply... 6 Stepping Motors... 7 DIP Switch (JP1) Location... 8 Setting the Output Current (JP1)... 8 Microstep Resolution (JP1)...
More informationilight Series Lighting Systems Lighting controls for a connected world
ilight Series Lighting Systems Lighting controls for a connected world You can get more out of your lighting system than you might think...much more Everyone needs lighting, and its all around us, so what
More informationQUALITY POWER SOLUTIONS BACKED UP BY REAL-WORLD ENGINEERING EXPERIENCE
QUALITY POWER SOLUTIONS BACKED UP BY REAL-WORLD ENGINEERING EXPERIENCE User s Manual SR250HL Power Supply/ Float Charger for Lead Acid Batteries STANDARD FEATURES OPTIONAL FEATURES 3 Relay Alarms-Form
More informationQuick Network Block QNB-1-B. User Manual
Quick Network Block QNB-1-B User Manual Issue 1.14 Battery Connection - up to 8/16 Amps of load can be delivered to the connected instruments in two separately fused banks for redundancy (8 or 16 Amp options
More informationLuna Decorative Light Source Range
Light Source User Guide Luna Decorative Light Source Range Models covered by this manual: UFO LUNA - CM UFO LUNA - TM UFO LUNA - MCM UFO LUNA - MTM UFO LUNA - CDMX UFO LUNA - TDMX UFO LUNA - C 0-10V UFO
More informationTOT Series Manual. North American CE and UK Models. CE Models. UK Models. North American Models
TOT Series Manual North American CE and UK Models CE Models UK Models North American Models Table of Content 1. Important Safety Instructions 2. Description Shipping Carton & Packing Material Placement
More informationSOLOdrive AC, 30W, 0-10V + AUX, 1 control channel, constant current, 1x 55V output, side feed, long metal
30W 0-10V 'Dim to Dark' LED Driver SOLOdrive SOLOdrive offers industry-best Natural Dimming to dark - LED dimming made beautiful! With any dimmer, in any application. Symbiosis on SOLOdrive stands for
More informationVertX. V100, V200 and V300. Installation Guide Barranca Parkway Irvine, CA USA. November Rev A.1
15370 Barranca Parkway Irvine, CA 92618 USA VertX V100, V200 and V300 Installation Guide November 2011 6080-930 Rev A.1. Contents Introduction... 3 Parts List... 3 Product Specifications... 3 Cable Specifications...
More informationPROFIBUS-DP/MODBUS RTU REPEATER
RP303 PROFIBUS-DP/MODBUS RTU REPEATER USER S MANUAL JAN/15 RP303 R P 3 0 3 M E smar www.smar.com Specifications and information are subject to change without notice. Up-to-date address information is available
More informationRE-82 RACK MOUNT DIMMER OWNERS MANUAL. 8 X 2400Watts. Revision /29/2007
RE-82 RACK MOUNT DIMMER 8 X 2400Watts OWNERS MANUAL Revision 2.4 11/29/2007 Page 2 of 8 RE-82 CONTROL PANEL DESCRIPTION The RE-82 is an 8 channel dimmer with a maximum capacity of 2,400 watts per channel
More informationDMC2. Installation Guide Version 1.0. Area for main photograph. Area for insert photo. W: 46.1mm up to 79 mm H: 46.1mm
Area for main photograph Area for insert photo W: 46.1mm up to 79 mm H: 46.1mm X: 12.6mm absolute on page Y: 132.6mm abs on page This insert has a shadow DMC2 Installation Guide Version 1.0 Contents DMC2
More informationRemote Time Delay Switch 3-wire version
RTDS3 energy saving controls Product Guide Remote Time Delay Switch 3-wire version today, tomorrow and in the future Issue 1.0 Product Overview The RTDS3 Remote Time Delay Switch provides timed switching
More informationOverview These instructions are presented as a guideline for installing and setting up the LX Series Breaker Control Panel.
LX Breaker Control Panels Installation and Setup Procedure Hubbell Building Automation, Inc. 9601 Dessau Road Building One Suite 100 Austin, Texas 78754 512-450-1100 512-450-1215 Fax www.hubbell-automation.com
More informationHydroGuard 4 to 20 ma Output Module. For use with HydroGuard Water Quality Monitor and Controller
HydroGuard 4 to 20 ma Output Module For use with HydroGuard Water Quality Monitor and Controller Technician's Manual Installation, Operation, and Maintenance Guide Chapter 1: Preface... 3 1.1 Intended
More informationACS-30-EU-MONI-RMM2-E
Multi-application heat tracing Control & Monitoring in commercial and residential buildings Technical Information Description Approvals CE marked Ambient operating Temperature range 25 C to +6 C Mounting
More informationInstallation, Operation and Maintenance Manual
Document 481200 VGD-100 Vari-Green Drive Installation, Operation and Maintenance Manual Please read and save these instructions for future reference. Read carefully before attempting to assemble, install,
More informationDEB 575/1200. Electronic Flicker Free Ballast DMX MOD INSTRUCTION AND MAINTENANCE MANUAL
Pag. # 1 DEB 575/1200 Electronic Flicker Free Ballast DMX MOD. 2515.210 INSTRUCTION AND MAINTENANCE MANUAL Pag. # 2 INDEX Section 1 - DESCRIPTION Section 2 - OPERATION & ROUTINE MAINTENANCE Section 3 DISPLAY
More informationDigital Lighting Systems, Inc.
, Inc. PD402-DMX Four Channel Dimmer and Switch Packs 4 x 2.5 Amps @ 6VDC to 24 VDC DMX52 compatible DMX52 4 x 2.5 Amps Dimmer Pack C UL US LISTED Digital Lighting Systems, Inc. USER'S MANUAL User's Manual
More informationINSTALLATION INSTRUCTIONS
TM REPLACEMENT PARTS FOR USE WITH CX SERIES PANELS INSTALLATION INSTRUCTIONS Hubbell Control Solutions 9601 Dessau Road Building One Suite 100 Austin, TX 78754 Toll Free: 888-698-3242 Fax: 512-450-1215
More informationSerial Module RS232C Standard. Technical Description
Computertechnik GmbH Serial Module RS232C Standard Technical Description Order number: 404.249010.000 6 ISA96 Serial Module RS323C standard Your contact: 2001 by Janich & Klass Computertechnik GmbH, Wuppertal
More informationADC7520 SERIES. 1600W Battery Chargers and Power Supplies
ADC7520 SERIES 1600W Battery Chargers and Power Supplies Wide output adjustment range 0 72VDC Analog control by external 0-5VDC voltage Temp.comp charging, sense as on option Power fail relay alarm Master-Slave
More informationSirius 24 and 48 DMX Output Kit Installation and Operation Instructions
Sirius 24 and 48 DMX Output Kit Installation and Operation Instructions Issue 5 - March 2002 Zero 88 Lighting Ltd reserves the right to make changes to the equipment described in this manual without prior
More informationSigma-XT-ECU-LCS Extinguishant Control Unit Local Control Station Operation and Maintenance Manual
SigmaXTECULCS Extinguishant Control Unit Local Control Station Operation and Maintenance Manual SigmaXTECULCS Issue 1 October 2011 Index Section Page 1 Introduction... 3 2 Safety and mounting... 3 2.1
More informationLight Source User Guide
Light Source User Guide Mercury Slimline Light Source Range Models covered by this manual: UFO MERSL3000M UFO MERSL 3000DMX UFO MERSL 3000 0-10V Please read this manual fully before installing, operating
More informationBLDA-1 & 2 Water Leak Detection Manual. CMR Electrical Ltd Bolton House Five Chimneys Lane Hadlow Down East Sussex TN22 4DX Tel:
BLDA-1 & 2 Water Leak Detection Manual CMR Electrical Ltd Bolton House Five Chimneys Lane Hadlow Down East Sussex TN22 4DX Tel: 01825 733600 Contents 1) System Overview 2) Installation 3) Wiring 4) Water
More informationACTpro Single Door IP Controller. Operating & Installation Instructions
ACTpro 1500 Single Door IP Controller Operating & Installation Instructions 18-00079 Issue 1 This manual refers to the ACTpro 1500 a TCP/IP based control unit supporting up to 32 doors. Access Control
More informationSTATUS Shiloh Road Alpharetta, Georgia (770) FAX (770) Toll Free
Instruction Manual Model 1582-45L Data Switch September 2010, Rev A REMOTE LOCAL SWITCH STATUS SELECT REMOTE LOCAL LOCAL SELECT CHANNEL SELECT POWER MODEL 1582 SWITCH CROSS TECHNOLOGIES, INC. Data, drawings,
More informationInstallation and User Guide
D5 Installation and User Guide 8-Channel DALI Controller (478) Introduction The 478 is for controlling DALI ballasts, drivers and load interface units (except for the 490 Blinds Controller). Do not connect
More informationDigital Lighting Systems, Inc. PD405-DMX. Four Channel Dimmer and Switch Packs. DMX512 compatible. PD405-DMX-24DC DMX512 4 x 5 Amps Dimmer Pack
Digital Lighting Systems, Inc. PD405DMX Four Channel Dimmer and Switch Packs DMX52 compatible PD405DMX24DC DMX52 4 x 5 Amps Dimmer Pack C UL US LISTED www.digitallighting.com Digital Lighting Systems,
More informationData sheet GCM MOD GMM EC.1 Communications module Modbus for GMM EC
Data sheet GCM MOD GMM EC.1 Communications module Modbus for GMM EC ERP no.: 5206415 GCM MOD GMM EC.1 www.guentner.de Page 2 / 15 Contents 1 GCM MOD GMM EC.1...3 1.1 Functional description...3 1.2 Connections...
More informationBS 287 DUAL CHANNEL POWER SUPPLY. User Manual. January 2017 V1.0
BS 287 DUAL CHANNEL POWER SUPPLY User Manual January 2017 V1.0 Table of contents 1.0 SAFETY INSTRUCTIONS... 3 2.0 GENERAL DESCRIPTION PS 289... 4 3.0 MECHANICAL INSTALLATION... 5 4.0 MAINS POWER & SAFETY
More informationABB Drives. User s Manual. Digital I/O Extension Module RDIO-01
ABB Drives User s Manual Digital I/O Extension Module RDIO-01 Digital I/O Extension Module RDIO-01 User s Manual 3AFE 64485733 REV B EN EFFECTIVE: 10.2.2003 2003 ABB Oy. All Rights Reserved. Safety Instructions
More informationProduct Data Sheet. BMS/Graphics Interface. Features
BMS/Graphics Interface Product Data Sheet Features The Mxp-010 interface allows BMS systems and graphics PCs to be integrated with the Mx- 4000 series of Fire Control Panels and Remote Terminals. The interface
More informationThis 4200-RM Rack Mount Kit is for installation in 4200-CAB series cabinets only.
Keithley Instruments, Inc. 28775 Aurora Road Cleveland, Ohio 44139 (440) 248-0400 Fax: (440) 248-6168 www.keithley.com Model 4200-RM Rack Mount Kit Packing List Introduction NOTE This 4200-RM Rack Mount
More informationExplosion-Protected Arc-Fault Protection ExAFCI Arc-Fault Circuit Interrupter
Installation, Operation & Maintenance Sheet Explosion-Protected Arc-Fault Protection ExAFCI Arc-Fault Circuit Interrupter > Contents 1 Contents 1 Contents...2 2 General Information...2 2.1 Manufacturer...2
More informationOverview Included in the Box: Pinout Installation Power Supply Stepping Motors DIP Switch (JP1) Location...
DRV7 USERS GUIDE Overview... 3 Included in the Box:... 4 Pinout... 4 Installation... 5 Power Supply... 6 Stepping Motors... 8 DIP Switch (JP1) Location... 9 Setting the Output Current (JP1)... 9 Microstep
More informationOperating Instructions Differential Pressure Transducer PS27
Operating Instructions Differential Pressure Transducer PS27 halstrup-walcher GmbH Stegener Straße 10 79199 Kirchzarten/Germany Phone: +49 (0) 76 61/39 63 0 Fax: +49 (0) 76 61/39 63 99 E-mail: info@halstrup-walcher.com
More informationSHUTTLE DC DIMMER DATA SHEET
SHUTTLE DC DATA SHEET BELL-PRESS MODEL: DC-LED-96W Compatible with all constant voltage LED drivers or power supplies Compatible with most constant current drivers, but must be tested before commissioning
More informationOperating instructions. Speed monitor D / / 2014
Operating instructions Speed monitor D200 80005257 / 00 05 / 2014 Contents 1 Preliminary note...4 1.1 Symbols used...4 1.2 Warning signs used...4 2 Safety instructions...5 2.1 General...5 2.2 Target group...5
More informationMC 11 EB-2 Power supply cabinet with external bus, AC version
MC 11 EB-2 Power supply cabinet with external bus, AC version USER/MAINTENANCE MANUAL 1 SLOT 0 SLOT 1 SLOT 2 SLOT 3 SLOT 4 SLOT 5 SLOT 6 SLOT 7 SLOT 8 SLOT 9 SLOT 10 SLOT 11 EB-2 (a) MC11 (b) (c) Figures
More informationTechnical Instructions MT15000/2 MT15000/2-M
Technical Instructions MT15000/2 MT15000/2-M CONTENTS Information and Recommendations... 3 Specifications... 3 1) MT15000/2... 2) MT15000/2-M... 3) PROTECTION... Wiegand or data clock device connection...
More informationM E M O R A N D U M I.S.
Physikalisch-Technische Bundesanstalt Department 3.6 " Intrinsic safety and Safety of Systems" 38023 Braunschweig Germany P.O. Box 33 45 Tel. ++49 531 592-3630 Fax ++49 531 592-3605 M E M O R A N D U M
More informationOperating instructions. Switching amplifier DN0210 DN / / 2015
Operating instructions Switching amplifier DN0210 DN0220 UK 80011079 / 00 01 / 2015 Contents 1 Preliminary note...4 1.1 Symbols used...4 1.2 Warning signs used...4 2 Safety instructions...5 2.1 General...5
More informationAVC 2 AUTOMATIC VOLUME CONTROL USERS MANUAL
AVC 2 AUTOMATIC VOLUME CONTROL USERS MANUAL GENERAL DETAIL The AVC2 will control a stereo channel to a preset maximum output level allowing the maximum sound level of a system to be controlled. The AVC2
More informationSigma Si. Extinguishant Status Unit (K , K , K , K , K , K , K , K )
Sigma Si Extinguishant Status Unit (K91100055, K91100056, K91110055, K91110056, K91111055, K91111056, K91111355, K91111356) Operation and Maintenance Manual Man1089 Issue 07 June 2013 Index Section Page
More informationOperating Manual / IEC. Explosion-Proofed Junction Boxes, Polyester. Wallücker Bahndamm 7 DE Kirchlengern
Operating Manual / IEC Explosion-Proofed Junction Boxes, Polyester Wallücker Bahndamm 7 DE- 32278 Kirchlengern Tel.: +49 5223 49107-0 Fax: +49 5223 49107-28 info@multi-box.com www.multi-box.com Contents
More informationAnalyser Control Unit Mk4. Operating Manual
Analyser Control Unit Mk4 Operating Manual Analyser Control Unit Mk4 Operating Manual Procal Analytics Limited Published by Procal Analytics Limited. All possible care has been taken in the preparation
More informationABB Drives. User s Manual. Analogue I/O Extension Module RAIO-01
ABB Drives User s Manual Analogue I/O Extension Module RAIO-01 Analogue I/O Extension Module RAIO-01 User s Manual 3AFE 64484567 REV A EN EFFECTIVE: 1.2.2002 2002 ABB Oy. All Rights Reserved. Safety
More informationANYtronics smartdim. 12 Channel Dimming System
ANYtronics smartdim 12 Channel Dimming System Installation notes 1.0 Introduction 2.0 Installation 2.1 Mains supply connection 2.2 Output connection 2.3 Input connections Operating instructions 3.0 Menu
More informationIGLOO IGLOO EASY INSTRUCTION MANUAL
ENGLISH EASY C695 C698 INSTRUCTION MANUAL PRELIMINARY Congratulations on choosing a Clay Paky product! We thank you for your custom. Please note that this product, as all the others in the rich Clay Paky
More informationInstallation and Hardware Guide
Helios W.E.S. 1000 & 2000 (Wireless Emergency Stop) Installation and Hardware Guide E5, Version 1.3 Helios Global Tech Ltd. Contact Information Helios Global Technologies 1920 Windsor Rd Kelowna BC V1Y
More informationModel: CAM430MV Wired Multi-View Camera with License Plate / Rear Surface Mount Installation Manual Features
Model: CAM430MV Wired Multi-View Camera with License Plate / Rear Surface Mount Installation Manual Features Fully Adjustable, Multiple Viewing Angle Smart Camera. High Resolution, 1/2 CMOS Color Camera
More informationgenesis TECHNICAL MANUAL Two-Door Controller GEN-045
Two-Door Controller GEN-045 Genesis Electronics Australia Pty Ltd www.genesiselectronics.com.au info@genesiselectronics.com.au Australian Owned, Designed and Manufactured Distributed By:- Genesis reserves
More informationModel HM-535 Power Supply Installation and Service Instructions
Model HM-535 Power Supply Installation and Service Instructions 430-535 0104 2004 Heritage MedCall, Inc SENTRY INSTALLATION & SERVICE INSTRUCTIONS POWER SUPPLY UNIT Model HM-535 IMPORTANT SAFETY INSTRUCTIONS
More informationTXM1.8RB. TX-I/O Blinds module
s 8 178 8178p01 TX-I/O Blinds module TXM1.8RB 8 non-floating relay outputs for... 4 blinds motors with 2 end switches, or 2 blinds motors with 3 end switches, or 2 blinds motors with 2 end switches + 1
More informationTOKISTAR LIGHTING INSTRUCTION MANUAL 24 VDC or 24 VAC
TokiLux TM Series TOKISTAR LIGHTING INSTRUCTION MANUAL 24 VDC or 24 VAC General Description Tokistar's TokiLux Series may be operated at 24 VDC or 24 VAC. Light Bars are installed end-to-end within the
More informationUser Guide Attracta Magnetic Lighting
User Guide Attracta Magnetic Lighting Magnetic Lighting System Models and accessories covered by this manual: UFO ATR-CM Corner Mount Extrusion UFO ATR-SM Surface Mount Extrusion UFO ATR-LG L Shaped Gantry
More informationDigital Keypad Introduction
K2 Digital Keypad Introduction The K02 uses the latest microprocessor technology to operate door strikes and security systems that require a momentary (timed) or latching dry contact closure. All programming
More informationDigital Lighting Systems, Inc. PD216. Two Channel Dimmer and Switch Packs PROTOCOL USER'S MANUAL. PD216-UM Rev. E - 02/03
Digital Lighting Systems, Inc. PD26 Two Channel Dimmer and Switch Packs PROTOCOL PD26 S2 S USER'S MANUAL PD26-UM Rev. E - 02/03 Digital Lighting Systems PD26 User's Manual - Page GENERAL DESCRIPTION The
More informationMXIO. Compact I/O module. Summary. Application Compact I/O module for data acquisition and HVAC control systems. Function
MXIO Compact I/O module Summary The MXIO multiple I/O compact module is a microprocessor-controlled, communicative module with the I/O mix optimized for larger HVAC control applications. The module uses
More informationQUICK START GUIDE. vau4/3. Frequency converter. operating instructions /12
operating instructions QUICK START GUIDE Frequency converter vau4/3 28100241101 12/12 1 Safety information Warning of electrical shock! Danger to life! Electrical shock can cause serious injury or even
More informationLight Control SLS ADRIA
Instruction and Mounting Manual Light Control SLS ADRIA 1 Introduction... 2 2 Safety instructions... 2 2.1 Meaning of the safety symbols... 2 2.2 General safety information... 2 3 Brief description...
More informationRS232 Control Box. Table of contents
Control Box Table of contents Page Introduction... Installation...5 Mounting the box System cable External power supply Location of switches and connectors Internal switch settings...8 Possible configurations...9
More informationCA-A480-A Elevator Controller. Reference & Installation Manual
CA-A480-A Elevator Controller Reference & Installation Manual TABLE OF CONTENTS INTRODUCTION.................................................................. 4 Introduction.............................................................................................
More informationPTC/PT100 board 2.0 Option
PTC/PT100 board 2.0 Option Instruction Manual - English PTC/PT100 board 2.0 Option Instruction Manual - English Document number: 01-3873-01 Edition: r1 Date of release: 2006-10-30 Copyright Emotron AB
More informationPSR-SCP- 24DC/SDC4/2X1/B PSR-SPP- 24DC/SDC4/2X1/B
PSR-SCP- 24DC/SDC4/2X1/B PSR-SPP- 24DC/SDC4/2X1/B Safety Relay for Emergency Stop and Safety Door Circuits INTERFACE Data Sheet 102858_02_en PHOENIX CONTACT - 12/2006 Description The PSR-...- 24DC/SDC4/2X1/B
More informationInternal Printer. Features.
Internal Printer Features Automatic Operation for o Fire o Fault o Alarms o Test On-Demand Option for Printing o Inputs o Outputs o Disablements o Event Log o Network Faults The operation and functions
More informationCRM Control Panel and Weather Detection System CRM3 for DC actuators (part # 40821J) CRM4 for AC actuators (part # 40822K)
CRM Control Panel and Weather Detection System CRM3 for DC actuators (part # 40821J) CRM4 for AC actuators (part # 40822K) CRM Applications CRM includes a control relay box and a power supply; additional
More informationPanel Installation Datasheet
ACTIONPAC LNS5 & SAFEGARD V5 Panel Installation Datasheet ELECTROSTATIC SENSITIVE DEVICE This product forms part of a life safety system. Failure to correctly store, handle, install and maintain the product
More informationSingle Channel Lighting Control Module
Product Guide LMS-MIN-LCM, LMS-MIN-LCM-DIM, LMS-MIN-LCM-EM Single Channel Lighting Control Module The LMS-MIN-LCM series of lighting control modules (LCMs) are used as part of the LMS Lighting Management
More informationABB Drives. User s Manual. Modbus Adapter Module RMBA-01
ABB Drives User s Manual Modbus Adapter Module RMBA-01 Modbus Adapter Module RMBA-01 User s Manual 3AFE 64498851 REV A EN EFFECTIVE: 1.3.2002 2002 ABB Oy. All Rights Reserved. Safety instructions Overview
More information