TRANS-ATS AUTOMATIC TRANSFER SWITCH

Transcription

1 TRANS-ATS AUTOMATIC TRANSFER SWITCH 1. Introduction 1.1 General Specifications The unit provides the mains voltage monitoring and automatic transfer switching. In the event of a mains voltage failure, the remote start relay output is energized and the unit automatically transfers the load from the mains to the generator. Both automatic and manual control is possible. A test mode is also available which allows the generator to be run without taking the load. The unit is extensively programmable through the front panel, with password protection on two levels. Operational parameters can also be monitored and controlled from a PC via a built-in USB port. The unit monitors generator operation and gives warning of any faults that are detected. If a fault is detected, the unit shuts down the engine and shows the failure message on the LCD display. 1. Warranty EMKO Elektronik warrants that the equipment delivered is free from defects in material and workmanship. This warranty is provided for a period of two years. The warranty period starts from the delivery date. This warranty is in force if duty and responsibilities which are determined in warranty document and instruction manual performs by the customer completely. 1.3 Maintenance Repairs should only be performed by trained and specialized personnel. Cut power to the device before accessing internal parts. Do not clean the case with hydrocarbon-based solvents (Petrol, Trichlorethylene etc.). Use of these solvents can reduce the mechanical reliability of the device. Use a cloth dampened in ethyl alcohol or water to clean the external plastic case. Introduction Brochure. ENG TRANS-ATS 1 V5 1/14

2 Ýçindekiler. Installation! Before beginning installation of this product, please read the instruction manual and warnings below carefully. A visual inspection of this product for possible damage occured during shipment is recommended before installation. It is your responsibility to ensure that qualified mechanical and electrical technicians install this product. If there is danger of serious accident resulting from a failure or defect in this unit, power off the system and seperate the electrical connection of the device from the system. Keep the power off until all of the wiring is completed so that electric shock and trouble with the unit can be prevented. Ýçindekiler.1 Configuration The unit can be programmed using the buttons and LCD display on the front panel or PC Software. Ýçindekiler. Panel Mounting The unit is designed for panel mounting. Fixing is by two screw fixings. 1- Insert the unit in the panel cut-out from the front. - Insert the fixings in the slotted at the corners of the unit and tighten the fixing screws to secure the unit against the panel.! During the equipment is putted in hole on the metal panel while mechanical installation some metal burrs can cause injury on hands, you must be careful. 15mm 135mm 9mm Figure.1 Front View 18mm Figure. Panel Cut-Out

3 .3 Electrical Connection TRANS-ATS three phase connections schematic LOAD L1 L L3 N Me c hanical i n t e rlock L1 GENERATOR L L3 MAINS L1 L L3 N N! Elect r ical interlock FUSE-6 FUSE-5 FUSE-4 G M FUSE-3 FUSE- FUSE Max. 3 Max. 3 8A Generator Contactor Relay Mains Contactor Relay 8A USB TRANSISTOR OUTPUTS MAX. 1 A BATTERY + 5A 5A FUSE-7 FUSE-8 BATTERY - BATTERY + Configurable Output-1 Configurable Output- Configurable Output-3 Configurable Output-4 BATTERY + Configurable Output-5 Remote Start or Configurable Output-6 1! BATTERY - Emergency Stop or Configurable Input-1 Mains Break. Feedback or Configurable Input- Gen. Break. Feedback or Configurable Input-3 Configurable Input-4 Configurable Input-5 Configurable Input-6 Configurable Input-7 Generator Ready or Configurable Input-8 BATTERY + FUSE-1, FUSE-, FUSE-5, FUSE-6 A. T FUSE-7 6 A. T FUSE-8 Max. 1 A. T FUSE-3, FUSE-4 8 A. T! 1- Connect the unit as shown in the appropriate diagram. Be sure to connect the battery supply the right way round and battery negative should be grounded. - Current transformers secondary should be grounded. 3

4 3. Changing And Saving Parameters Values Operation Screen MAINS V1: 38V V1: V V3: 38V V: V V31: 38V V3: V Mains okay When the Prog button is pressed, the parameters section is asked for accessing to parameters. PROGRAM Operator setting Technician setting Factory adjustment Press the Up or Down buttons to select the section you wish to view/change. PROGRAM Operator setting Technician setting Factory adjustment Press the Enter button. TECHNICIAN SETTING Password Enter password with cursor (Right, Left, Up and Down) buttons. TECHNICIAN SETTING Password 16 Note1: If Enter button is pressed and the technician password is zero, Password screen is ignored. TECHNICIAN SETTING System Mains Generator Power supply Press the Enter button to confirm password. If the password is incorrect, the unit will drop out of program mode. Press the Up or Down buttons to select the main parameter group you wish to view/change. TECHNICIAN SETTING System Mains Generator Power supply GENERATOR Volt level Frequency level Current level & act. Power level Press Enter button to access to all parameters page in currently main parameter group. Press Enter button to access to all parameters in currently parameter page. GENERATOR VOLT LEVEL Under volt shutdown Under volt prealarm Under volt reset Over volt shutdown GENERATOR VOLT LEVEL Under volt shutdown 3 Vac Parameter can be changed with Up and Down buttons. Press the Enter button to view parameter value. GENERATOR VOLT LEVEL Under volt shutdown 35 Vac GENERATOR Volt level Frequency level Current level & act. Power level Press Enter button to confirm the changed value. When the Escape button is pressed any time, previous page can be accessed. GENERATOR VOLT LEVEL Under volt shutdown Under volt prealarm Under volt reset Over volt shutdown To exit from programming mode any time, press Prog button. MAINS V1: 38V V1: V V3: 38V V: V V31: 38V V3: V Mains okay Operation Screen 4

5 4. Parameters 4.1 Operator Parameters Mains MAINS VOLT LEVEL (Mains->Volt level) Under volt trip Mains Under Voltage Under volt reset Mains Under Voltage Reset Over volt trip Mains Over Voltage Over volt reset Mains Over Voltage Reset Max MAINS FREQ. LEVEL (Mains->Frequency level) Under freq trip Mains Under Frequency Under freq reset Mains Under Frequency Reset Over freq trip Mains Over Frequency Over freq reset Mains Over Frequency Reset Max Generator GENERATOR VOLT LEVEL (Generator->Volt level) Under volt shutdown Generator Under Voltage Shutdown Under volt prealarm Generator Under Voltage Pre-Alarm Under volt reset Generator Under Voltage Pre-Alarm Reset Over volt shutdown Generator Over Voltage Shutdown Over volt prealarm Generator Over Voltage Pre-Alarm Over volt reset Generator Over Voltage Pre-Alarm Reset Shutdown delay time Generator Voltage Shutdown Delay Time Max 6(dis) 6 3 6(dis) (dis) GENERATOR FREQ LEVEL (Generator->Frequency level) Max Under freq shutdown Generator Under Frequency Shutdown 3.(dis) Under freq prealarm Generator Under Frequency Pre-Alarm 3.(dis) Under freq reset Over freq shutdown Over freq prealarm Over freq reset Generator Under Frequency Pre-Alarm Reset Generator Over Frequency Shutdown Generator Over Frequency Pre-Alarm Generator Over Frequency Pre-Alarm Reset 3. 3.(dis) 3.(dis) Shutdown delay time Generator Frequency Shutdown Delay Time GENERATOR CUR LEVEL (Generator->Current level) Under cur. set Under cur. prealarm Under cur. reset Over cur. set Over cur. prealarm Over cur. reset Generator Under Current Set Generator Under Current Pre-Alarm Generator Under Current Pre-Alarm Reset Generator Over Current Set Generator Over Current Pre-Alarm Generator Over Current Pre-Alarm Reset Max 1 A (dis) dis A 5 A A (dis) 999 A 998 A Note: dis = disable 5

6 GEN POWER LEVEL (Generator->Power level) Under power shutdown Under power prealarm Under power reset Over power shutdown Over power prealarm Over power reset Shutdown delay time Reverse power set Generator Under Power Shutdown Generator Under Power Pre-Alarm Generator Under Power Pre-Alarm Reset Generator Over Power Shutdown Generator Over Power Pre-Alarm Generator Over Power Pre-Alarm Reset Generator Power Shutdown Delay Time Reverse Power Set (dis) (dis) (dis) (dis) - Max 99 dis dis 5 dis dis kw GEN WORKING CALENDAR (Generator->Working calendar) Disable/enable select Working Calendar Disable or Enable Start time on monday Working Calendar Work Start Time on Monday Stop time on monday Working Calendar Work Stop Time on Monday Start time on tues. Stop time on tuesday Start time on wednes. Stop time on wednes. Start time on thurs. Stop time on thursday Start time on friday Stop time on friday Start time on satur. Stop time on saturday Start time on sunday Stop time on sunday Working Calendar Work Start Time on Tuesday Working Calendar Work Stop Time on Tuesday Working Calendar Work Start Time on Wednesday Working Calendar Work Stop Time on Wednesday Working Calendar Work Start Time on Thursday Working Calendar Work Stop Time on Thursday Working Calendar Work Start Time on Friday Working Calendar Work Stop Time on Friday Working Calendar Work Start Time on Saturday Working Calendar Work Stop Time on Saturday Working Calendar Work Start Time on Sunday Working Calendar Work Stop Time on Sunday Max /ENABL Technician Parameters 4..1 System SYSTEM NETWORK (System->Network) CT ratio Current Transformer Ratio PT ratio Voltage Transformer Ratio Type of AC system Phase sequence Generator rating Select AC system; Generator Phase Sequence (dis, L13 or L31) Generator rating set - 1 Phase Wire 1-3 Phase 4 Wire - Phase 3 Wire L1-L 3- Phase 3 Wire L1-L3 Max , L13, L31 3 Note: dis = disable 6

7 BREAKERS (System->Breakers) Type of Breaker Gen.brk.cls.contact Gen.brk.cls.relay Gen.brk.cls.time Gen.brk.open relay Gen.brk.open time Mains.brk.cls.contact Mains.brk.cls.relay Mains.brk.cls.time Mains.brk.open relay Mains.brk.open time Break.close puls.time Break.open pulse time Transfer time Spring loading time Retry number Hardware Breaker Selection Gen Close Breaker Contact Type Gen Close Breaker Relay Type Gen Close Timer Gen Open Breaker Relay Type Gen Open Timer Mains Close Breaker Contact Type Mains Close Breaker Relay Type Mains Close Timer Mains Open Breaker Relay Type Mains Open Timer Breaker Close Pulse Time Breaker Open Pulse Time Transfer Time Spring Loading Time Retry Number LCD DISPLAY (System->LCD display) Language Language Selection Contrast Contrast Setting Auto backlight off Auto Backlight Off Auto scroll time Auto Scroll Time Auto scroll number * 1 Auto Scroll Number Err. mesg scroll time Scroll Time For Error Messages Max NO / NC NOR / PULS NOR / PULS NO / NC NOR / PULS NOR / PULS Max ENGLISH/CHINESE ENGLISH ENABL/ (dis) COMMUNICATION (System->Communication) Max Slave address Slave Address Baud rate Parity Baud Rate: - 1 baud 1-4 baud - 48 baud 3-96 baud 4-19 baud baud Parity: - NONE ODD - EVEN Stop bit Stop Bit (-> 1 stop bit,1-> stop bit) 1 DATE & TIME SET (System->Date & time set) Year Month Year Month Day Week Hour ute ond Max Date 1 31 Day of week 1 7 Hour 3 ute 59 ond 59 Note: * 1 = Maximum value of this parameter is 4 at TRANS-AMF.CN device. NO / NC : Normally Open / Normally Close NOR / PULS : Normal / Pulse 7

8 DEFAULT SETTINGS (System-> settings) Save setting to def. Save setting to default Reset default sets Reset default sets Reset factory sets Reset factory sets PASSWORD SETTINGS (System->Password settings) Operator password Operator Password Technician password Technician Password Max YES / NO NO YES / NO NO YES / NO NO Max 4.. Mains MAINS VOLT LEVEL (Mains->Volt level) Under volt trip Mains Under Voltage Under volt reset Mains Under Voltage Reset Over volt trip Mains Over Voltage Over volt reset Mains Over Voltage Reset Max MAINS FREQ. LEVEL (Mains->Frequency level) Under freq trip Mains Under Frequency Under freq reset Mains Under Frequency Reset Over freq trip Mains Over Frequency Over freq reset Mains Over Frequency Reset Max MAINS ACTIONS (Mains->Actions) Mains failure detect Mains Failure Detection En/Dis Mains fail.stop mode Look Mains Failure at Stop Mode En/Dis Always return delay Always Look Mains Return Delay Max ENABL/ ENABL ENABL/ ENABL ENABL/ 4..3 Generator GENERATOR VOLT LEVEL (Generator->Volt level) Under volt shutdown Generator Under Voltage Shutdown Under volt prealarm Generator Under Voltage Pre-Alarm Under volt reset Generator Under Voltage Pre-Alarm Reset Over volt shutdown Generator Over Voltage Shutdown Over volt prealarm Generator Over Voltage Pre-Alarm Over volt reset Generator Over Voltage Pre-Alarm Reset Shutdown delay time Generator Voltage Shutdown Delay Time Max 6(dis) 6 3 6(dis) (dis) GENERATOR FREQ LEVEL (Generator->Frequency level) Max Under freq shutdown Generator Under Frequency Shutdown 3.(dis) Under freq prealarm Generator Under Frequency Pre-Alarm 3.(dis) Under freq reset Over freq shutdown Over freq prealarm Over freq reset Generator Under Frequency Pre-Alarm Reset Generator Over Frequency Shutdown Generator Over Frequency Pre-Alarm Generator Over Frequency Pre-Alarm Reset 3. 3.(dis) 3.(dis) Shutdown delay time Generator Frequency Shutdown Delay Time Note: dis = disable 8

9 GEN CUR LEVEL & ACT (Generator->Current level & act.) Under cur. set Generator Under Current Set Under cur. prealarm Generator Under Current Pre-Alarm Under cur. reset Generator Under Current Pre-Alarm Reset Under cur. act. Generator Under Current Actions - Disable 1 - Warning (Alarm Only, No Shutdown) - Electrical Trip (Alarm/Off Load Generator Followed By Shutdown After Cooling) 3 - Shutdown (Alarm And Shutdown) Under act. delay time Over cur. set Over cur. prealarm Over cur. reset Over cur. act. Over act. delay time Short circuit cur. Generator Under Current Actions Delay Time Generator Over Current Set Generator Over Current Pre-Alarm Generator Over Current Pre-Alarm Reset Generator Over Current Actions - Disable 1 - Warning (Alarm Only, No Shutdown) - Electrical Trip (Alarm/Off Load Generator Followed By Shutdown After Cooling) 3 - Shutdown (Alarm And Shutdown) Generator Over Current Actions Delay Time Generator Short Circuit Current Set Max 1 (dis) dis 5 (dis) 3 dis 99 (dis) (dis) dis A A A A A A A GEN POWER LEVEL (Generator->Power level) Under power shutdown Under power prealarm Under power reset Over power shutdown Over power prealarm Over power reset Shutdown delay time Reverse power set Reverse power act. Rv.pow.act.delay time Generator Under Power Shutdown Generator Under Power Pre-Alarm Generator Under Power Pre-Alarm Reset Generator Over Power Shutdown Generator Over Power Pre-Alarm Generator Over Power Pre-Alarm Reset Generator Power Shutdown Delay Time Reverse Power Set Reverse Power Actions - Disable 1 - Warning (Alarm Only, No Shutdown) - Electrical Trip (Alarm/Off Load Generator Followed By Shutdown After Cooling) 3 - Shutdown (Alarm And Shutdown) Reverse Power Action Delay Time (dis) (dis) (dis) (dis) - (dis) Max dis dis 5 dis dis (dis) kw 9

10 GEN WORKING CALENDAR (Generator->Working calendar) Disable/enable select Working Calendar Disable or Enable Start time on monday Working Calendar Work Start Time on Monday Stop time on monday Working Calendar Work Stop Time on Monday Start time on tues. Stop time on tuesday Start time on wednes. Stop time on wednes. Start time on thurs. Stop time on thursday Start time on friday Stop time on friday Start time on satur. Stop time on saturday Start time on sunday Stop time on sunday Working Calendar Work Start Time on Tuesday Working Calendar Work Stop Time on Tuesday Working Calendar Work Start Time on Wednesday Working Calendar Work Stop Time on Wednesday Working Calendar Work Start Time on Thursday Working Calendar Work Stop Time on Thursday Working Calendar Work Start Time on Friday Working Calendar Work Stop Time on Friday Working Calendar Work Start Time on Saturday Working Calendar Work Stop Time on Saturday Working Calendar Work Start Time on Sunday Working Calendar Work Stop Time on Sunday Max /ENABL GENERATOR GENERAL (Generator->General) Max Sens.option gen.freq Sensing Options Generator Frq En/Dis ENABL/ ENABL All warning are latch All Warnings Are Latched En/Dis ENABL/ 4..4 Power Supply ENGINE PLANT BATTERY (Engine->Plant battery) Max Under volt Battery Undervolts Warning 6.(dis) Under volt reset Battery Undervolts Warning Reset Under volt delay Battery Undervolts Volts Delay Over volt Battery Overvolts Warning 6.(dis) Over volt reset Battery Overvolts Warning Reset Over volt delay Battery Overvolts Delay Engine LOAD TEST (Engine->Load test) Max Disable/enable select Disable, No Load or On Load Selection -DISABLE 1-NO LOAD -ON LOAD 1-NO LOAD EXERCISE (Engine->Exercise) Time of Period Week Start time Generator exercise working period on related day Generator exercise working day of week Generator exercise work start time on related day Max (dis) 99 dis ENGINE GENERAL (Engine->General) Engine running volt Engine Running Voltage Engine running freq. Engine Running Frequency Max 6(dis)

11 4..6 Inputs CONF. INPUT-X (Inputs->Conf. input-x) Dis,user conf.or list - Disable 1- User Configured - Select From List Indication Activation Select from list - Normally Open (Close To Activate) If User Configured - Status 1- Warning Non-Latching - Warning Latching 3- Electrical Trip 4- Shutdown If User Configured - Active From Starting 1- Active From Safety On - Always Active If Select From List -Remote Start On Load 1-Remote Start Off Load -Auxiliary Mains Fail 3-Simulate Lamp Test Button 4-Simulate Horn Reset Button 5-Simulate Alarm Reset Button 6-Simulate Auto Button 7-Simulate Test Button 8-Simulate Manual Button 9-Simulate Start Button 1-Simulate Stop Button 11-Generator Closed Auxiliary 1-Generator Load Inhibit 13-Mains Closed Auxiliary 14-Mains Load Inhibit 15-Auto Restore Inhibit 16-Auto Start Inhibit 17-Panel Lock 18-Scheduled Runs(Exercise) Inhibited 19-Reserved -Transfer To Generator/Open Mains 1-Transfer To Mains/Open Generator -Remote Inhibit 3-Engine Running 4-Generator available 5 - Emergency Stop (for only input-1) Max in1= (dis) in, 3= in4, 5= in6, 7= in8= 1 in1, 3=1 in, 4= in5, 6= in7, 8= 4 in1= in= in3=4 in4= in5= in6= in7= in8= in1, = in3, 4= in5, 6= in7, 8= in1=5 in=4 in3=4 in4=4 in5=4 in6=4 in7=4 in8=4 in1=5 in=13 In3=11 in4=19 in5=3 in6=7 in7=3 in8=4 Active delay Input active delay 5 in1= in, 3, 4=1 in5, 6, 7=1 In8=1 Note-1 : x = 1(input-1), (input-), 3(input-3), 4(input-4), 5(input-5), 6(input-6), 7(input-7) or 8(input-8) Note- : 5 - Emergency Stop (for only input-1) Note-3 : dis = disable 11

12 CONF. EXP. INPUT-X (Inputs->Conf. exp. input-x) Dis,user conf.or list - Disable 1- User Configured - Select From List Hardware type Indication Activation Select from list Active delay -> -Ve (Switched To Battery -) 1-> +Ve (Switched To Battery +) - Normally Open (Close To Activate) If User Configured - Status 1- Warning Non-Latching - Warning Latching 3- Electrical Trip 4- Shutdown If User Configured - Active From Starting 1- Active From Safety On - Always Active If Select From List -Auxiliary Mains Fail 3-Simulate Lamp Test Button 4-Simulate Horn Reset Button 5-Simulate Alarm Reset Button 6-Simulate Auto Button 7-Simulate Test Button 8-Simulate Manual Button 9-Simulate Start Button 1-Simulate Stop Button 11-Generator Closed Auxiliary 1-Generator Load Inhibit 13-Mains Closed Auxiliary 14-Mains Load Inhibit 15-Auto Restore Inhibit 16-Auto Start Inhibit 17-Panel Lock 18-Scheduled Runs Inhibited 19-Reserved -Transfer To Generator/Open Mains 1-Transfer To Mains/Open Generator Input active delay Max (dis) Note-1 : x = 1(exp. input -1), (exp. input -), 3(exp. input -3), 4(exp. input -4), 5(exp. input -5), 6(exp. input -6), 7(exp. input -7) or 8(exp. input -8) Note- : dis = disable 1

13 4..7 Outputs CONF. OUTPUT-1 (Outputs->Conf. output-1) - Normally Open (Close To Activate) -NOT USED 1-AIR FLAP CONTROL -ALARM RESET 3-AUDIBLE ALARM 4-AUTO START INHIBIT 5-AUXILIARY MAINS FAILURE 6-BATTERY HIGH VOLTAGE 7-BATTERY LOW VOLTAGE 8-CALLING FOR SCHEDULED RUN(EXERCISE) 9-RESERVED 1-RESERVED 11-RESERVED 1-COMMON ALARM 13-COMMON ELECTRICAL TRIP ALARM 14-COMMON SHUTDOWN ALARM 15-COMMON WARNING ALARM 16-COOLING FAN AFTER START 17-COOLING FAN AFTER STOP 18-RESERVED 19-RESERVED -COOLING DOWN TIMER IN PROGRESS 1-RESERVED -DELAYED ALARMS ACTIVE 3-DIGITAL INPUT1 ALARM 4-DIGITAL INPUT ALARM 5-DIGITAL INPUT3 ALARM 6-DIGITAL INPUT4 ALARM 7-DIGITAL INPUT5 ALARM 8-DIGITAL INPUT6 ALARM 9-DIGITAL INPUT7 ALARM 3-EXPANSION INPUT1 ALARM 31-EXPANSION INPUT ALARM 3-EXPANSION INPUT3 ALARM 33-EXPANSION INPUT4 ALARM 34-EXPANSION INPUT5 ALARM 35-EXPANSION INPUT6 ALARM 36-EXPANSION INPUT7 ALARM 37-EXPANSION INPUT8 ALARM 38-DIGITAL INPUT8 ALARM 39-EMERGENCY STOP 4-FAIL TO START ALARM 41-FAIL TO STOP ALARM 4-RESERVED 43-RESERVED 44-RESERVED 45-GENERATOR AT REST 46-GENERATOR AVAILABLE 47-GENERATOR CLOSED AUXILIARY 48-GENERATOR FAILED TO CLOSE 49-GENERATOR FAILED TO OPEN 5-GENERATOR HIGH FREQUENCY PRE-ALARM 51-GENERATOR HIGH FREQUENCY SHUTDOWN 5-GENERATOR HIGH VOLTAGE PRE-ALARM 53-GENERATOR HIGH VOLTAGE SHUTDOWN 54-GENERATOR LOAD INHIBIT 55-GENERATOR LOW FREQUENCY PRE-ALARM 56-GENERATOR LOW FREQUENCY SHUTDOWN 57-GENERATOR LOW VOLTAGE PRE-ALARM 58-GENERATOR LOW VOLTAGE SHUTDOWN 59-GENERATOR STOPPING 6-GENERATOR OPEN BREAKER 61-HORN OUTPUT LATCHED 6-HORN OUTPUT PULSED 63-LAMP TEST 64-RESERVED 65-RESERVED 66-RESERVED 67-RESERVED 68-MAINS CLOSED AUXILIARY 69-MAINS FAILED TO CLOSE 7-MAINS FAILED TO OPEN 71-MAINS FAILURE 7-MAINS HIGH FREQUENCY 73-MAINS HIGH VOLTAGE 74-MAINS LOAD INHIBIT 75-MAINS LOW FREQUENCY 76-MAINS LOW VOLTAGE 77-MAINS OPEN BREAKER 78-NO LOADING COMMAND 79-RESERVED 8-RESERVED 81-RESERVED 8-RESERVED 83-OVER CURRENT PRE-ALARM 84-OVER CURRENT 85-OVER POWER PRE-ALARM 86-OVER POWER SHUTDOWN 87-RESERVED 88-RESERVED 89-PANEL LOCK 9-RESERVED 91-RESERVED 9-RESERVED 93-RESERVED 94-REMOTE START PRESENT 95-RESERVED 96-SHORT CIRCUIT 97-RESERVED 98-RESERVED 99-STARTING ALARMS ARMED 1-RESERVED 11-SYSTEM IN AUTO MODE 1-SYSTEM IN MANUAL MODE 13-SYSTEM IN STOP MODE 14-SYSTEM IN TEST MODE 15-UNDER CURRENT PRE-ALARM 16-UNDER CURRENT 17-UNDER POWER PRE-ALARM 18-UNDER POWER SHUTDOWN 19-RESERVED 11-RESERVED 111-WAITING FOR GENERATOR 11-RESERVED 113-LOAD SUPPLY FROM GENERATOR 114-LOAD SUPPLY FROM MAINS 115-RESERVED 116-RESERVED 117-RESERVED 118-RESERVED 119-RESERVED 1-RESERVED 11-RESERVED 1-REMOTE CONTROL ACTIVE 13-REVERSE POWER 14-RESERVED 15-RESERVED 16-RESERVED 17-RESERVED 18-RESERVED 19-REMOTE OUTPUT Max

14 CONF. OUTPUT- (Outputs->Conf. output-) - Normally Open (Close To Activate) Max CONF. OUTPUT-3 (Outputs->Conf. output-3) - Normally Open (Close To Activate) Max CONF. OUTPUT-4 (Outputs->Conf. output-4) - Normally Open (Close To Activate) Max CONF. OUTPUT-5 (Outputs->Conf. output-5) - Normally Open (Close To Activate) Max CONF. OUTPUT-6 (Outputs->Conf. output-6) - Normally Open (Close To Activate) Max CONF. EXP. OUTPUT-1 (Outputs->Conf. exp. output-1) - Normally Open (Close To Activate) Max CONF. EXP. OUTPUT- (Outputs->Conf. exp. output-) - Normally Open (Close To Activate) Max CONF. EXP. OUTPUT-3 (Outputs->Conf. exp. output-3) - Normally Open (Close To Activate) Max CONF. EXP. OUTPUT-4 (Outputs->Conf. exp. output-4) - Normally Open (Close To Activate) Max CONF. EXP. OUTPUT-5 (Outputs->Conf. exp. output-5) - Normally Open (Close To Activate) Max CONF. EXP. OUTPUT-6 (Outputs->Conf. exp. output-6) - Normally Open (Close To Activate) Max

15 CONF. EXP. OUTPUT-7 (Outputs->Conf. exp. output-7) - Normally Open (Close To Activate) Max CONF. EXP. OUTPUT-8 (Outputs->Conf. exp. output-8) - Normally Open (Close To Activate) Max Timers START TIMERS (Timers->Start timers) Max Mains transient delay Mains Transient Delay... Mains fail start dely Mains Fail Start Delay Remote start delay Remote Start Delay 36 4 Generator fail delay Generator fail delay 5 45 Safety on delay Safety On Delay 99 5 Warming up time Warmup Time 5 3 Horn duration Horn Duration (dis) STOPPING TIMERS (Timers->Stopping timers) Max Mains return delay Mains Return Delay 36 5 Remote stop delay Remote Stop Delay 5 4 Cooling time Cooling Time (dis) 36 6 Fail to stop delay Fail To Stop Time Expansion Modules IO (1-8) MODULE (Expansion modules->io (1-8)) Disable/enable select Expansion I/O Module Selection CAN fault actions Can Fault Actions: - Disable 1- Warning Non-Latching - Warning (Alarm Only, No Shutdown) 3- Electrical Trip (Alarm/Off Load Generator Followed By Shutdown After Cooling) 4- Shutdown (Alarm And Shutdown) Max ENABL/ (dis) 4 CAN fault activation Can Fault Activation: - Active From Starting 1- Active From Safety On - Always Active CAN fault delay Can Fault Delay 5 1 DIAL-UP & ETHERNET (Expansion modules-> Dial-up & Ethernet) Max Disable/enable select Expansion Dal-up&Ethernet Module Selection ENABL/ Call back selection Call Back Selection ENABL/ Note: dis = disable cont = continuous 15

16 GSM MODULE (Expansion modules->gsm) Disable/enable select Expansion GSM Module Selection Call back selection Call Back Selection SMS SMS Feature Enable or Disable Max ENABL/ ENABL/ ENABL/ GPRS MODULE (Expansion modules->gprs) Disable/enable select Expansion GPRS Module Selection Call back selection Call Back Selection Max ENABL/ ENABL/ WEB SERVER MODULE (Expansion modules->web Server Disable/enable select Web Server Module Selection Max ENABL/ 4..1 User Adjustment MAINS VOLTAGE OFFSET (User adjustment->mains voltage offset) Mains V1 offset Mains V offset Mains V3 offset Mains V1 Offset Mains V Offset Mains V3 Offset GEN. VOLTAGE OFFSET (User adjustment->gen. voltage offset) Gen. V1 offset Gen. V offset Gen. V3 offset Generator V1 Offset Generator V Offset Generator V3 Offset CURRENT OFFSET (User adjustment->current offset) Current I1 offset Current I offset Current I3 offset Current I1 Offset Current I Offset Current I3 Offset Max Max Max - A - A - A BATTERY OFFSET (User adjustment->battery offset) Max Batt.volt offset Battery Voltage Offset Note: dis = disable 16

17 5. Specifications Equipment use Housing & Mounting Panel Cut-Out Protection Weight Environmental rating Operating/Storage Temperature Operating/Storage Humidity Installation Over Volt. Category Pollution Degree Mode of Operation DC Battery Supply Voltage Cranking Dropouts : Electrical control equipment for generating sets. : 9 mm x 15 mm x 41 mm. (including connectors). Plastic housing for panel mounting. : 18mm x 135mm. : IP65 at front panel. : Approximately,53 Kg. : Standard, indoor at an altitude of less then meters with non-condensing humidity. : - C to +7 C / -3 C to +8 C : 9 % max. (non-condensing) : II Appliances, portable equipment : II, Normal office or workplace, non conductive pollution : Continuous. : 8 to 3 V. Max. operating current is 36 ma. : Battery voltage can be VDC for max. 5 ms during cranking (battery voltage should be at least nominal voltage before cranking). Battery Voltage Measurement Mains Voltage Measurement Mains Frequency : 8 to 3 V, accuracy: 1 % FS, resolution:,1 V : 3 to 3 VAC Ph-N, 5 to Accuracy: 1 % FS, Resolution: 1 V. : 5 to 99.9 (min. VAC Ph-N) Accuracy:,5 % FS, Resolution:,1. Generator Voltage Measurement : 3 to 3 VAC Ph-N, 5 to Accuracy: 1 % FS, Resolution: 1 V. Generator Frequency : 5 to 99.9 (min. VAC Ph-N) Accuracy:,5 % FS, Resolution:,1. CT secondary : 5A. Communication interface : USB programming and communication port. Optional Expansion I/O Module : Expansion I/O module including 8 inputs and 8 outputs. Optional Comm. Modules : Ethernet/Dial-up, GSM/GPRS and Web Server modules. Relay Outputs : Generator contactor relay output 8A@5 Mains contactor relay output 8A@5 Configurable output-5 5A@5 Configurable output-6 5A@5 Transistor Outputs : Configurable output-1 1A at DC supply voltage Configurable output- 1A at DC supply voltage Configurable output-3 1A at DC supply voltage Configurable output-4 1A at DC supply voltage All transistor ouputs supplied from DC supply terminal 17

18 6. Other Informations Manufacturer Information: Emko Elektronik Sanayi ve Ticaret A.Þ. Demirtaþ Organize Sanayi Bölgesi Karanfil Sk. No: BURSA/TURKEY Phone : Fax : Repair and maintenance service information: Emko Elektronik Sanayi ve Ticaret A.Þ. Demirtaþ Organize Sanayi Bölgesi Karanfil Sk. No: BURSA/TURKEY Phone : Fax : Your Technology Partner Thank you very much for your preference to use Emko Elektronik products, please visit our web page to download detailed user manual. 18