INCLUDED HARDWARE REQUIRED TOOLS GETTING STARTED DISCLAIMERS! 5/32 Allen Wrench (Provided)

Transcription

1 UPSIDE

2 INCLUDED HARDWARE 8 x 5/8 Screw M6x16 REQUIRED TOOLS 5/32 Allen Wrench (Provided) GETTING STARTED Assemble on a soft surface to avoid scratching the worksurface. Hardware & tools required may vary depending on the UpSide specifics. The following instructions do not specify the amount of hardware included. Due to variations in design, a separate hardware list will be provided. DISCLAIMERS! Product that is damaged by the end user due to misuse, accident, abuse, negligence or shipping is not covered under Three H warranty. Use tools and hardware mentioned above to avoid any product faults. It is best to assemble our furniture with 2 or more persons. If you believe you are missing pieces, please contact replacements@three-h.com

3 STEP 1 Place the worksurface face down on a soft, clean surface. STEP 2 Install the Legs Place the height adjustable legs in position. Align with the pre-drilled holes for Step 3. STEP 3 Fasten the Legs Using six M6x16mm bolts for each leg.

4 STEP 4 Fasten the Base Plates Align the base plates with the predrilled holes on the legs and fasten using 4 M6x16mm bolts. STEP 5 Power Plug in the power cords into the leg mechanism. STEP 6 Initialisation Flip the desk onto its bases and plug it into the power source. Test the desk by lowering it to the bottom and raising it to the top. If the systems fails initialisation may be required. (see page 9)

5 Important information Important information on LINAK products can be found under the following headings: Warning! Failure to comply with these instructions may result in accidents involving serious personal injury. Failing to follow these instructions can result in the product being damaged or being destroyed. Safety instruction General Safe use of the system is possible only when the operating instructions are read completely and the instructions contained are strictly observed. Failure to comply with instructions marked with the NOTE symbol may result in serious damage to the system or one of its components. It is important for everyone who is to connect, install, or use the systems to have the necessary information and access to this User Manual. Follow the instructions for mounting risk of injury if these instructions are not followed. The appliance is not intended for use by young children or infirm persons without supervision. If there is visible damage on the product it must not be installed. Note that during construction of applications, in which the actuator is to be fitted, there must be no possibility of personal injury, for example the squeezing of fingers or arms. Assure free space for movement of application in both directions to avoid blockade.

6 Before installation, re-installation, or troubleshooting: Stop the DL5/DL6 Pull out the mains plug. Relieve the DL5/DL6 of any loads, which may be released during the work. Before start-up: Make sure that the system has been installed as instructed in this User Manual. Make sure that the voltage of the control box is correct before the system is connected to the mains. System connection. The individual parts must be connected before the control box is connected to the mains. See the User Manual for LINAK actuators, if necessary. During operation If the control box makes unusual noise or smells, switch off the mains voltage immediately. Take care that the cables are not damaged. Unplug the mains cable on mobile equipment before it is moved. The products must only be used in an environment, that corresponds to their IP protection. Misc. The actuator system has a sound level below 55dB(A) in typical applications. Updated manuals and declarations can always be found here:

7 Repairs In order to avoid the risk of malfunction, all DESKLINE repairs must only be carried out by authorised LINAK workshops or repairers, as special tools must be used and special gaskets must be fitted. Lifting units under warranty must also be returned to authorised LINAK workshops. Warning! If any of the DESKLINE products are opened, there will be a risk of subsequent malfunction. Warning! The DESKLINE systems do not withstand cutting oil.

8 Electrical connection of the DL5/DL6 system The DESKLINE DL5/DL6 system is to be connected as shown on figure 4a (2 stage) or figure 4b (3 stage). Each DL5/Dl6 is the connected to the sockets on the control box by means of the motor cables, which have a 6-plug in each end. Figure 5. Finally, the mains cable is to be mounted and power switched on. Please note that the control box must only be connected to the voltage stated on the label. CBD4/CBD5/CBD6 with earth The CBD4/CBD5/CBD6 earth cable to be mounted on the desk construction (typically the top frame)in a way that ensures good electrical contact. The function of the earth cable is to earth the desk and ground static electricity. The earth connection does not protect other electrical products. CBD4/CBD5 with mains cut-off (non ZERO models) If the power cable is damaged it has to be replaced by an authorized LINAK service centre to avoid any danger. Figure 4a Figure 4b Figure 5

9 Initialisation of the DESKLINE DL5/DL6 parallel systems The DESKLINE system is intialised by pressing the down button once or twice and holding it down until DL5/ DL6 runs into end stop, it will then automatically run approx. 3 mm out again and hereafter slowly running in again. Only release the down button when the movement has completely stopped. If the key is released before the sequence is completed then the initialisation is interupted and must be started again from the beginning. It is sometimes necessary to press the down button twice to start the initialisation this is because the system can be in different modes when the initialisation starts. Approx. 5 mm The CBD5 and CBD6 can control DL5 and DL6 in 2 parallel while the CBD4 can control DL5 and DL6 in 2, 3, and 4 parallel so that the desk is always kept horizontal. Anti-Collision The function (anti-collision) is an option for the standard CBD4/CBD5/CBD6 advanced/control box software version 1.66 and later. A system with anti-collision can limit material damages on a desk if a collision with a solid object should occur. Enabling the anti-collision To enable the anti-collision function a little plug called a dongle must be mounted in one of the 2 control ports. The function is only active when the dongle is mounted. If you remove the dongle again you disable the function. Method of operation When the DL/DB s are running the CBD4/CBD5/CBD6 monitors the current consumption on each channel using a special algorithm. If the current consumption on one channel is increased more than a predefined slope, a collision is assumed and all channels are stopped immediately and all DL/DB s will start to run in the opposite direction (approx. 50 mm). This return drive is done automatically and continues with or without any control key pressed (for max. 2.5 sec.). The anti-collision sensitivity is different in upward and downward direction. Upwards the force is approx. 20 kg. Downwards the load will be approx. 40 kg + the load on the DL/DB (the desk + what is on top of the desk). The 40 kg are needed to activate the anti-collision function. Situations where the anti-collision does not work There are situations where the anti-collision will not be activated. These situations are: If the collision happens during the initialisation phase If the collision happens within the first 1000 msec or after the control button has been released If the collision happens between the floor and the table and the load on the desk + the weight of the legs are lower than 40 kg If the collision happens over too long time, e.g. if the collision is with a soft object.

10 DIAGNOSTIC CODES FOR CBD6S DIAGNOSTIC CODES NAME DESCRIPTION CBD4/5/6 EQUIVALENT POTENTIAL CAUSE SOLUTION/ TROUBLESHOOTING E01 Position Lost The desk has an unknown position and needs to be initialized E01 Position error New desk leg added E08 Watchdog Indicate that software failed to kick watchdog E08 Program fault Unplug mains cable for 15 sec. Replace control box E09 LIN Collision Collisions detected on the LIN bus E49 E10 Power Fail Power fail happened E14 Key pressed on two or more connected handsets simultaneously Multiple LINBUS devices activated simultaneously Mains cable pulled during driving Internal fault Check if another desk panel is connected and being activated Unplug all but one desk panel and test system Check mains cable is not caught and is allowed to freely travel E11 Channel mismatch Change in number of actuators since initialization E15 Disconnection Desk leg added Change motor cable or Desk Leg E12 Position Error One channel has position different than others E13 Too much back drive occurred Move table to fully retracted position E13 Short Circuit Short circuit detected during operation E10 Squeezed motor cable Short in motor Check motor cable connections Isolate and replace motor cable Isolate and replace desk leg E16 Key Error Illegal keys pressed (handled internally Dp1C) E16 Hitting multiple buttons simultaneously Check switch E17 Safety Missing LIN bus unit does not support safety feature NEW DP1C/ DPF1C does not have up-todate software Try DP with more recent software version (version printed on label) E18 Missing Initialization Plug A special service tool is required to change number of channels to the system NEW [BASELIFT ONLY] Service tool missing from BASELIFT system when initializing Add service tool E23 Ch1 Missing Channel 1 is detected missing E17 E24 Ch2 Missing Channel 2 is detected missing E18 E25 Ch3 Missing Channel 3 is detected missing E19 E26 Ch4 Missing Channel 4 is detected missing E48 Disconnection Faulty motor cable Faulty motor leg Disconnection Faulty motor cable Faulty motor leg Disconnection Faulty motor cable Faulty motor leg Disconnection Faulty motor cable Faulty motor leg Change motor cable or Desk Leg Change motor cable or Desk Leg Change motor cable or Desk Leg Change motor cable or Desk Leg E27 Ch5 Missing Channel 5 is detected missing E28 Ch6 Missing Channel 6 is detected missing E29 Ch1 Type Channel 1 is not same type as when initialized E20 Change in desk leg type Loose wire inside motor Check desk leg type Change desk leg E30 Ch2 Type Channel 2 is not same type as when initialized E21 Change in desk leg type Loose wire inside motor Check desk leg type Change desk leg E31 Ch3 Type Channel 3 is not same type as when initialized E22 Change in desk leg type Loose wire inside motor Check desk leg type Change desk leg E32 Ch4 Type Channel 4 is not same type as when initialized E23 Change in desk leg type Loose wire inside motor Check desk leg type Change desk leg

11 DIAGNOSTIC CODES FOR CBD6S DIAGNOSTIC CODES NAME DESCRIPTION CBD4/5/6 EQUIVALENT POTENTIAL CAUSE SOLUTION/ TROUBLESHOOTING E33 Ch5 Type Channel 5 is not same type as when initialized E34 Ch6 Type Channel 6 is not same type as when initialized E35 Ch1 Pulse Fail Channel 1 had too many pulse errors E24 Loose/ faulty cable Hall sensor PCB Change Desk Leg E36 Ch2 Pulse Fail Channel 2 had too many pulse errors E25 Loose/ faulty cable Hall sensor PCB Change Desk Leg E37 Ch3 Pulse Fail Channel 3 had too many pulse errors E26 Loose/ faulty cable Hall sensor PCB Change Desk Leg E38 Ch4 Pulse Fail Channel 4 had too many pulse errors E27 Loose/ faulty cable Hall sensor PCB Change Desk Leg E39 Ch5 Pulse Fail Channel 5 had too many pulse errors E40 Ch6 Pulse Fail Channel 6 had too many pulse errors E41 Ch1 Overload Up Overload up occurred on Channel 1 E28 Leg is overloaded Reached end stop (before initialization at upper end-stop occurs) Remove load E42 Ch2 Overload Up Overload up occurred on Channel 2 E29 Leg is overloaded Reached end stop (before initialization at upper end-stop occurs) Remove load E43 Ch3 Overload Up Overload up occurred on Channel 3 E30 Leg is overloaded Reached end stop (before initialization at upper end-stop occurs) Remove load E44 Ch4 Overload Up Overload up occurred on Channel 4 E31 Leg is overloaded Reached end stop (before initialization at upper end-stop occurs) Remove load E45 E46 Ch5 Overload Up Ch6 Overload Up Overload up occurred on Channel 5 Overload up occurred on Channel 6 E47 Ch1 Overload DW Overload down occurred on channel 1 E32 E48 Ch2 Overload DW Overload down occurred on channel 2 E33 E49 Ch3 Overload DW Overload down occurred on Channel 3 E34 E50 Ch4 Overload DW Overload down occurred on Channel 4 E35 E51 Ch5 Overload DW Overload down occurred on Channel 5

12 DIAGNOSTIC CODES FOR CBD6S DIAGNOSTIC CODES NAME DESCRIPTION CBD4/5/6 EQUIVALENT POTENTIAL CAUSE SOLUTION/ TROUBLESHOOTING E52 Ch6 Overload DW Overload down occurred on Channel 6 E53 Ch1 Anti-Col Anti Collision triggered on Channel 1 E36 E54 Ch2 Anti-Col Anti Collision triggered on Channel 2 E37 E55 Ch3 Anti-Col Anti Collision triggered on Channel 3 E38 E56 Ch4 Anti-Col Anti Collision triggered on Channel 4 E39 E57 Ch5 Anti-Col Anti Collision triggered on Channel 5 E36 [Reserved for future development] [Reserved for future development] E58 Ch6 Anti-Col Anti Collision triggered on Channel 6 E37 [Reserved for future development] [Reserved for future development] E59 Ch1 SLS/ PIEZO Safety limit switch activated on Channel 1 E40 E60 Ch2 SLS/ PIEZO Safety limit switch activated on Channel 2 E41 E61 Ch3 SLS/ PIEZO Safety limit switch activated on Channel 3 E42 E62 Ch4 SLS/ PIEZO Safety limit switch activated on Channel 4 E43 E63 Ch5 SLS/ PIEZO Safety limit switch activated on Channel 5 E64 Ch6 SLS/ PIEZO Safety limit switch activated on Channel 6 E65 Ch1 Pulse Dir Pulses counted wrong direction in Channel 1 E44 Motor poles are crossed Hall sensor Cables are crossed Exchange desk leg E66 Ch2 Pulse Dir Pulses counted wrong direction in Channel 2 E45 Motor poles are crossed Hall sensor Cables are crossed Exchange desk leg E67 Ch3 Pulse Dir Pulses counted wrong direction in Channel 3 E46 Motor poles are crossed Hall sensor Cables are crossed Exchange desk leg E68 Ch4 Pulse Dir Pulses counted wrong direction in Channel 4 E47 Motor poles are crossed Hall sensor Cables are crossed Exchange desk leg E69 Ch5 Pulse Dir Pulses counted wrong direction in Channel 5 E70 Ch6 Pulse Dir Pulses counted wrong direction in Channel 6 E71 Ch1A Short Short circuit detected on Channel 1A NEW [Reserved for use with Homeline system] [Reserved for use with Homeline system] E72 Ch1B Short Short circuit detected on Channel 1B NEW [Reserved for use with Homeline system] [Reserved for use with Homeline system]

13 Need Help? April 30, 2018 Revision No.1