VMB1DM Dimmer Module for Velbus system. Velbus manual VMB1DM edition 1 rev.2.0 1

Transcription

1 Dimmer Module for Velbus system Velbus manual edition 1 rev.2.0 1

2 IDEX IDEX... 2 FEATURES... 3 COECTIO... 5 COECTIO OF THE BUB... 5 Use with light bulb (resistive load):... 5 Use with low-mains halogen through an electronic transformer (capacitive load):... 5 Use with low-mains halogen through a wound transformer (inductive load):... 6 Troubleshooting:... 6 OW-VOTAGE COECTIO... 7 Direct control using several push buttons:... 7 Control via VE system:... 8 Combination of direct push buttons and VE control :... 9 COECTIO Termination: Addressing: Time setting: Operation mode: Operation: ED indication: earning mode: Velbus manual edition 1 rev.2.0 2

3 FEATURES Fit for light bulbs, halogen on mains and low-mains halogen in combination with a dimmable electronic transformer. Phase cut-off technology for resistive (light bulbs) and capacitive (dimmable electronic transformers) loads. Phase cut-off technology for inductive loads (dimmable wound transformers). oiseless through CoolMOSIM FET. Mains pollution (EMI) conform E55015 Required mains voltage: V/60Hz of V/50Hz Maximum load: 230V or 115V Built-in non-resettable fuse Gradual switch on or off (ca. 1.5s) will prolong the lamp s life Dimming from 0 to 100% in ca. 4 seconds Manual control on the module ED indicators for: The operation modes (slow, fast, very fast or 2 x blinking and continuously O) The power voltage Data reception and forwarding through VE 9 different operation modes (adjustable through mode rotary switch): Moment control Start/stop timer Staircase lighting timer Dimmer Dimmer with memory function Multi-position dimmer Slow-on dimmer Slow-off dimmer Slow on-off dimmer 16 possible time set-ups (adjustable through hexadecimal rotary switch): moment - 5s - 10s - 15s - 30s - 1min - 2 min - 5min - 10min - 15min - 30min - 1u - 2u - 5u - 1dag - on/off Controllable by connecting several push buttons in parallel. Push button input debounce: 65ms. Control through VE. Programmable without PC. Easy learning process by operating the desired push buttons in the learning mode. 7 different control possibilities: Using push buttons turning on the lamp to full intensity. Using push buttons turning the lamp off. Using push buttons turning on the lamp to full intensity or turning off the lamp Using push buttons activating the set operation mode. Using push buttons increasing the lamp s light intensity Using push buttons decreasing the lamp s light intensity Using push buttons creating atmospheric lighting. Using push buttons turning on the lamp on the desired intensity. Memory for 14 different push buttons/sliders per command. earned push buttons are saved ion case of a power failure. Report to control modules for modifying the ED status. 247 possible addresses (adjustable through rotary switch) Required mains voltage: VDC Consumption in standby: 35mA at 18V (15mA at 16V). Consumption activated relay: 50mA at 18V (30mA at 16VDC) Standard DI-rail housing (2 modules) Dimensions ( x W x H): 90 x 36 x 58mm. Weight : 95g Velbus manual edition 1 rev.2.0 3

4 VE: 2-wire communication for VE data and 2 wires for power. Data transfer: 16,6Kbit/s. Serial data protocol: CA (Controller Area etwork) Short-circuit proof (towards negative or positive of power) Bus error indication: 2 x short flash of the operation mode ED. Self restoring after 25 seconds in case of a bus error. Possibility to assign a name (max. 16 characters) and a reaction time (65ms, 1s, 2s of 3s) which can be saved in the non-volatile memory. The module can react to push button messages sent over the VE. A modification of the dim status will be reported on the VE. When modifying the dim status, the module will send instructions to adjust the status of the EDs on the control modules. Instructions will be accepted when calling up the module type, module name, module status, reading from or writing to the non-volatile memory, configuration of the light intensity and when starting or stopping the timer. The module can respond with the module type, module name, module status or the contents from the memory. Velbus manual edition 1 rev.2.0 4

5 COECTIO COECTIO OF THE BUB Use with light bulb (resistive load): 115V AC POWER 230V AC POWER OAD OAD H - PB H - PB Warning: Place the rotary switch on one of the following positions: 0, 1, 2, 3, 4, 5, 6 or 7. Use with low-mains halogen through an electronic transformer (capacitive load): AC PRIM Dimmable electronic transformer AC PRIM Dimmable electronic transformer 115V AC POWER 230V AC POWER OAD OAD H - PB H - PB Attention: Place the rotary switch on one of the following positions: 0, 1, 2, 3, 4, 5, 6 or 7. The electronic transformer must be short-circuit proof and thermal protected. The electronic transformer must be suited to adjust the light intensity with a phase cut-off dimmer. Velbus manual edition 1 rev.2.0 5

6 Use with low-mains halogen through a wound transformer (inductive load): Dimmable transformer PRIM Dimmable transformer PRIM 115V AC POWER 230V AC POWER OAD OAD H - PB H - PB Attention: Place the rotary switch on one of the following positions: : 8, 9, A, B, C, D, E or F. The electronic transformer must be short-circuit and thermal protected. Make sure to always connect a lamp on the transformer (an unloaded transformer has an inductive behavior and could damage the dimmer). This dimmer is not suited for toroidal transformers. Troubleshooting: The dimmer module features a non-resettable fuse which will melt in case of a short-circuit or overload. In this case, return the dimmer to the manufacturer for repair. If the lamp does not go out due to an external cause (even after switching off and on the mains), the control transistor will probably be faulty. In this case, return the dimmer to the manufacturer for repair. Velbus manual edition 1 rev.2.0 6

7 OW-VOTAGE COECTIO Connect the 12 to 18VCC (mind the polarity) to the module. Make sure to use a heavier wire gauge (0,5mm2 or more) with long connections. The dimmer module can be controlled via push buttons which are directly connected to the push button input by using the VE or a combination of both possibilities. Direct control using several push buttons: 230V AC POWER OAD H - PB PUSH BUTTOS + SUPPY - Remark: Position the address on 00 to switch off the communication with the VE. Also, erase all learnt push buttons. In the other case, de dimmer module will cause a bus error with every status modification.. Velbus manual edition 1 rev.2.0 7

8 Control via VE system: 230V AC POWER OAD H - PB H TWISTED 2 PAIR (0.5mm ) + SUPPY - Velbus manual edition 1 rev.2.0 8

9 Combination of direct push buttons and VE control : 230V AC POWER OAD H - PB PUSH BUTTOS H TWISTED PAIR (0.5mm 2 ) + SUPPY - Remark: For connection between the modules, use twisted pair cable (ex. EIB 2x2x0.8mm2, UTP 8x0.51mm - CAT5 or other). Use minimum 0.5mm² cable. Connect the bus (mind the polarity) to the module. Velbus manual edition 1 rev.2.0 9

10 COECTIO Remove the lid from the dimmer module using a small screwdriver and modify the configuration. 230VAC 115VAC amp Address setting OAD Operation mode ED Operation mode Time setting Replace the lid Forwarding ED Power ED Reception ED TERM H - PB Manual control Termination supply VE Direct push button control Termination: If the module is connected at the start or end of a cable on the VE, place the TERM jumper. Remove the jumper in all other cases. Remark: For connection between the modules, use twisted pair cable (ex. EIB 2x2x0.8mm2, UTP 8x0.51mm - CAT5 or other). Use minimum 0.5mm² cable. Connect the bus (mind the polarity) to the module. Velbus manual edition 1 rev

11 Addressing: Enter a unique address (from 00 to FE except for 81, 91, A1, B1, C1, D1, E1, FE and FF ) for each module through the rotating switches. These addresses can be used to learn the push buttons. In case of a modification of the addresses, the lamp will be switched off and all EDs of the corresponding control push buttons will be turned off. Time setting: A time will be chosen depending on the configuration of the rotating switch: Description 0 Moment control (the lamp will be on so long as the push button is being controlled) 1 5s timer or 5s dimming speed in slow on/off dimmer mode 2 10s timer or 10s dimming speed in slow on/off dimmer mode 3 15 timer or 15s dimming speed in slow on/off dimmer mode 4 30s timer or 30s dimming speed in slow on/off dimmer mode 5 1min timer or 1min dimming speed in slow on/off dimmer mode 6 2min timer or 2min dimming speed in slow on/off dimmer mode 7 5min timer or 5min dimming speed in slow on/off dimmer mode 8 10min timer or 10min dimming speed in slow on/off dimmer mode 9 15min timer or 15min dimming speed in slow on/off dimmer mode A 30min timer or 30min dimming speed in slow on/off dimmer mode B 1h timer or 1h dimming speed in slow on/off dimmer mode C 2h timer or 2h dimming speed in slow on/off dimmer mode D 5h timer or 5h dimming speed in slow on/off dimmer mode E 1day timer or 1day dimming speed in slow on/off dimmer mode F o timer or maximum dimming speed in slow on/off dimmer mode Remark: If different cable wiring topologies (tree, star, loop,...) are used, place a jumper on the end module of the longest cable only, OT on each end point Velbus manual edition 1 rev

12 Operation mode: The dimmer module will operate as follows, according to the configuration of the '' rotating switch: Operation mode Description 0 or *8 Start/stop timer Operating the push button will turn the lamp on. After the set time (see rotary switch) has elapsed, the lamp will be turned off. Operating the push button while the lamp is on will switch off the lamp immediately. 1 or *9 Staircase lighting timer Operating the push button will turn the lamp on. After the set time (see rotary switch) has elapsed, the lamp will gradually turn off and will be completely switched off after 30 seconds. Operating the push button while the lamp is on will restart the timer. 2 or *A Dimmer A short press will turn on the lamp to full intensity. A short press while the lamp is on will switch off the lamp. A long press will dim the lamp until the maximum or the minimum is reached. A next operation will reverse the dimming direction. After the set time (see rotary switch) has elapsed, the lamp will turn off. 3 or *B Dimmer with memory function A short press will turn on the lamp at the intensity which was last used. A short press while the lamp is on will switch off the lamp. A long press will dim the lamp until the maximum or the minimum is reached. A next operation will reverse the dimming direction. After the set time (see rotary switch) has elapsed, the lamp will turn off. 4 or *C Multi-position dimmer Operating the push button will turn on the lamp to full intensity. Each time the push button is pressed within 5 seconds after the previous operation the light intensity will modify with 25%. If the lamp is on and the previous operation happened more than 5 seconds ago, the lamp will turn off. After the set time (see rotary switch) has elapsed, the lamp will turn off. 5 or *D Slow-on dimmer Operating the push button will turn on the lamp gradually. The time needed for the lamp to burn at full intensity depends on the rotating switch used to determine the time setting (see rotary switch). Operating the push button while the lamp is on will switch off the lamp immediately. 6 or *E Slow-off dimmer Operating the push button will turn on the immediately to full intensity. Operating the push button while the lamp is burning at full intensity will turn off the lamp gradually. The time needed for the lamp to turn off completely depends on the rotating switch used to determine the time setting (see rotary switch). Operating the push button while the lamp turns off gradually will immediately turn on the lamp to full intensity. 7 or *F Slow on/off dimmer Operating the push button will turn on the lamp gradually. Operating the push button while the lamp is on will turn off the lamp gradually. The time needed for the lamp to turn on or off depends on the rotating switch used to determine the time setting (see rotary switch). * Modes 8 up to F are used with inductive loads (wound transformer) Remarks: The set mode is only applicable on push buttons connected to the direct push button input and to push buttons connected via the Velbus which were attributed the mode function in the learning mode (see learning mode). If the rotary switch is set on 0, the dimmer module will always operate in moment control, regardless of the set operating mode. In other words: the light bulb will burn as long as the push button is being pressed. If the rotary switch is set on F, the dimmer module will not automatically deactivate or the dimming speed will be at its peak if the module is set in slow on, slow off or slow on/off mode. Velbus manual edition 1 rev

13 Operation: The dimmer module can be operated in different ways: Using push buttons connected to the direct push button input: o activating the set mode on the module.. Using push buttons connected to the Velbus through a push button interface or control module: o turning on the lamp to full intensity. o switching off the lamp. o turning on the lamp to full intensity or turning off the lamp. o activating the set operation mode. The mode and time setting will influence the dimmer module only when using these push buttons (see operation mode and time setting table). o increasing the lamp s intensity. A short press will turn on the lamp to full intensity (a short press with the dimmer with memory function will, in case the lamp is off, turn on the lamp at the intensity which was last used). A long press will increase the lamp s intensity until the push button is released. o decreasing the lamp s intensity. A short press will immediately switch off the lamp. A long press will decrease the lamp s intensity until the push button is released. o turning on the lamp to a specific light intensity (atmosphere). o using sliders turning on the lamp to the desired intensity ED indication: The control module EDs and the operation mode ED on the dimmer module indicate the status of the dimmer: The ED will burn if the lamp does not light up. The ED will burn if the lamp burns at a stable light intensity. The ED blinks rapidly as long as the lamp s light intensity is modifying. The ED blinks slowly when the switch-off delay is running. The ED blinks very rapidly if the dimmer module is set in learning mode. earning mode: Only push buttons connected to the Velbus via a push button interface or a control panel are appropriate for the procedure below. Each command can accept up to 14 different push buttons. Memorize he unique address of the module. Address Command F1 OFF: earning push buttons switching off the lamp E1 O: earning push buttons turning on the lamp to full intensity D1 TG: earning push buttons turning on the lamp to full intensity or turning the lamp off C1 DIM: earning push buttons/sliders activating the set mode on the module B1 UP: earning push buttons increasing the lamp s intensity A1 DW: earning push buttons decreasing the lamp s intensity 91 ATM: earning push buttons turning on the lamp to a specific light intensity (atmosphere) 81 ADM: amp s light intensity for corresponding atmosphere push buttons The lamp will be switched off and the operation mode ED will blink very rapidly to indicate the learning mode. The EDs of the learned push buttons will also blink very rapidly. In this way it is possible to see which push buttons for the corresponding group have already been learned. You can add a specific push button by maintaining it pressed until the lamp lights up. When releasing the push button the lamp will switch off and the push button indication ED will blink very rapidly as a confirmation. If this does not work then the maximum amount of push buttons has been reached. To delete a learned push button, maintain it pressed. When releasing the push button the indication ED will be turned off. You can delete all learned push buttons for a specific control group by maintaining the manual control on the dimmer module pressed until the lamp lights up. When releasing the manual control push button the lamp and the indication EDs of all corresponding push buttons will turn off. To learn a light atmosphere set the dimmer module on address 81. The EDs of the push buttons creating atmospheric light will blink rapidly. To assign a specific light intensity to an atmosphere push button, operate the corresponding push button until the desired light intensity has been reached. Velbus manual edition 1 rev

14 To set all learned atmospheric setting to full intensity, maintain the manual control on the dimmer module pressed until the lamp burns at full intensity. When releasing the manual control push button the lamp and the indication EDs of all corresponding push buttons will turn off. To learn the sliders, set the learning address on C1. Operate the slider until the lamp turns on and the corresponding ED blinks rapidly. Erase a learned slider by operating the slider until the indication ED turns off. Quit the learning mode by resetting the dimmer module s original address. When using firmware version 0735 you will be able to delete all push buttons and sliders saved into the memory of the dimmer module at once. Set the address to one of the learning addresses. Maintain the manual control on the dimmer module pressed for 10 seconds. The relay will activate and deactivate again after 7 seconds to confirm the push buttons have been erased. Set the address back to its original value. Velbus manual edition 1 rev

15 Refer to our website for more information: Velbus manual edition 1 rev