Sealed snap-action pushbutton switches bushing Ø 12 mm momentary

Transcription

1 SW-IM-709 DISTINCTIVE FEATURES Snap-action : tactile feedback with audible click High current/voltage rating Sealed to IP67 Flat round actuator for optional marking NO+NC ENVIRONMENTAL SPECIFICATIONS Front panel sealing : IP67 according to IEC 6059 Shock resistance : 50 g - ms according to IEC Salt spray : IEC 5-6, test f Operating temperature : -0 C to +85 C (-0 F to +85 F) Storage temperature : -0 C to +85 C (-0 F to +85 F) ELECTRICAL SPECIFICATIONS Max. current/voltage rating with resistive load : A 8 VDC Initial contact resistance : 00 mω max. Insulation resistance : GΩ min. at 500 VDC Dielectric strength : 500 Vrms between terminals Electrical life at full load : 5,000 cycles GENERAL SPECIFICATIONS Panel thickness :.5 mm (.059) to 0 mm (.9) Total travel :.7 mm (.067) ± 0. mm Low level or mechanical life :,000,000 cycles Torque (applied to nut) : Nm max. with metal nut U66.5 Nm max. with plastic nut U8 MATERIALS Case : polyamide /6 Actuator : polyamide 6/6 Bushing/bezel : polyamide 6/6 Contacts : silver, gold plated Terminal seal : epoxy The company reserves the right to change specifications without notice. B

2 AGENCY APPROVAL A 5 VAC/50 VAC File E88 MOUNTING STANDARD BEZEL (CONTINUED) BACK OF PANEL SPACE REQUIREMENT Availability : consult factory for details of approved models. Marking : to order switches marked UL, complete appropriate box of ordering format. PANEL CUT-OUT.90 (.507).50min-0.00Max (.059MIN.-.9MAX.) Ø.60 (.55DIA) Ø.50 (.5DIA) - Flat seal MATRIX MOUNTING TERMINALS.70 (.6).00 (.09) Straight P.50 (.8) CIMCP 7.60 (.99) (.0).0 (.09).0 (.07) Quick-connect Z CIM PANEL CUT-OUT MOUNTING REDUCED BEZEL.90 (.507) 0.80min-.0Max (.0MIN.-.69MAX.).50min-0.00Max (.059MIN.-.9MAX.) ELECTRICAL FUNCTIONS Ø.60 (.55DIA) (.689) (.689) Ø (.96) Ø5.60 (.6DIA) Ø.50 (.5DIA) - Flat seal Function 7 () MATRIX MOUNTING MOUNTING STANDARD BEZEL 7.50 (.689) BACK OF PANEL SPACE REQUIREMENT - O-ring 0 B

3 BUILD YOUR PART NUMBER BASIC PART NUMBER IM SERIES ACTUATOR SHAPES ELECTRICAL FUNCTION TERMINALS CONTACTS R P Round, curved Round, flat 7 NC + NO P Z Straight PC Quick-connect Silver, gold plated (standard) Actuator marking available on round flat models (symbol 0 mm max.). On request. OPTIONS ACTUATOR COLORS BUSHING & BEZEL BEZEL OPTIONS ACTUATOR OPTION APPROVAL Blue B Dark blue Black Black Other : on request Standard bezel Dia. 5 (.590) reduced bezel, front mounting Std actuator 0 High actuator UL Consult factory for detail of approved models. Green Grey Dia. 5 (.590) reduced bezel, std mounting 5 Yellow 6 Red 7 White 9 Orange ABOUT THIS SERIES On the following pages, you will find successively basic part numbers of switches and options in the same order as in above chart. Notice : please note that not all combinations of above numbers are available. Refer to the following pages for further information. A sealing boot is available to protect the switches against frost and sand (P/N U55). See "Sealing Boots" section of website. Mounting accessories : Standard hardware supplied : flat seal (standard bezel) or O-ring (reduced bezel) and metal hex nut mm (.55) across flats. Hex nut part number U66. Plastic nut 7 mm (.669) across flats, thickness mm (.57) available on request. Part number U8.

4 Flat actuator Ø.00 (.7DIA) 0.80 (.5) Ø.00x0.75SI (.7DIAx0.75IS) 0.50 (.00).5 (.).00 (.09) (.0).5 (.) FLAT CIMR7P Ø.00 (.7DIA).00 (.078) (.96) STANDARD BEZEL QUICK-CONNECT TERMINALSCIRSH.50 (.8) EPOXY IMP7P Ø7.50 (.688DIA).70 (.6) (.96) IMR7P 8. (.7) Curved actuator Common terminal identified by a horizontal dash.00 (.078) FLAT STANDARD BEZEL STRAIGHT PC TERMINALS Ø7.50 (.688DIA) Page 0--- Curved actuator CIRSH 0.80 (.5) Ø.00x0.75SI (.7DIAx0.75IS) Page 0--- CIMR7P IMP7Z 0.50 (.00).5 (.) Ech (.07).5 (.) 7.60 (.99) EPOXY Flat actuator.0 (.09) IMR7Z.00 (.866) (.0) LE 8/0/0 CIMR7Z CIRSH B ACTUATOR COLORS Page 0--- CIRSH Blue Dark blue Black Green Grey Yellow Red White Orange Page 0--- CIMR7Z Ech 0.9 LE 8/0/0 BUSHING AND BEZEL Black (standard) Other : on request

5 BEZEL OPTIONS Ø (.96) Ø (.96) Standard bezel Dia. 5 (.590) reduced bezel, mounting of the switch from the front into a threaded panel cut-out Dia. 5 (.590) reduced bezel, standard mounting CIM ACTUATOR OPTION Standard actuator High actuator Ø.00 (.7DIA) Ø.00 (.7DIA).70 (.85) 0.70 (.85) CIM Ech IMR 0 IMP LE 8/0/0 AGENCY APPROVAL UL Availability : consult factory for details of approved models. Marking : to order switches marked UL, complete appropriate box of ordering format. 5