Revision C SVAB GRIP L8. technical information

Transcription

1 Revision C SVAB GRIP L8 technical information

2

3 Revision table Revision Description Page Date Signature Authorized A First edition FRJA FRER B Added data to SMG toggle switch. Added underlaying joystick graphics to front plate positions. Added data to cables. Added info/feature about dead man usage. Added info about pos. 3 back side not being pluggable. Also added info about the possibility to use a toggle swith in position , FRJA FRER C Changed graphics according to new graphic profile FRJA FRER 2013 SVAB Hydraulik AB. All rights reserved. SVAB accepts no responsibility for possible errors in catalogs, brochures and other printed material. SVAB reserves the right to alter its products without prior notice. This also applies to products already ordered provided that such alterations can be made without affecting agreed specifications. All trademarks in this material are properties of their respective owners.

4

5 Contents Page 1. INTRODUCTION L8 - GENERAL TECHNICAL DATA CABLES HOLE PATTERN LAYOUT FRONT PLATE HOLE PATTERN LAYOUT BACK SIDE HOLE PATTERN LAYOUT PROPORTIONAL THUMBWHEEL PUSHBUTTONS TOGGLE SWITCHES, LEDs AND MINITRIM MOUNTINGS PRODUCT CONFIGURATION CODE L8 JOYSTICK GRIP POSITIONS ACCESSORIES ADAPTER BALL KIT FOR STANDARD MOUNTING L BELLOW WASHERS BELLOW ADAPTERS FOR STANDARD BELLOW WASHER...29

6 1. INTRODUCTION The SVAB Grip L8 is designed as an ergonomic joystick grip for earth-moving machinery. It can be fitted with up to three proportional thumbwheels which can be controlled by the thumb or the index finger. It can also be equipped with up to 9 pushbuttons (7 with 2 proportional thumbwheels). Available with direct analog/digital outputs and also with SVAB internal CAN bus connection where it thereby can interact directly with other CAN bus connected units in SVAB systems. It is possible to combine both analog/digital and CAN bus output in the same grip. The L8 grip comes in both left and right hand design and in dark gray or black coloring. 6 INTRODUCTION

7 2. L8 - GENERAL TECHNICAL DATA SVAB GRIP L8 DIMENSIONS (in millimeters) AND TECHNICAL DATA Info: The development of the SVAB Grip L8 joystick grip comes from long experience and ergonomic studies which has given the L8 great comfort and functionality Features: Ergonomically designed. 165 Rubberized surface. Room for thumbwheels and push buttons on both the front and back. Easily mounted on market joystick bases. Both hydraulic and electric. Adapted for a large variety of thumbwheels, pushbuttons and toggle switches. Operating temperature range -40 C to 70 C Storage temperature -40 C to 85 C Case material PC/ABS Coating Soft touch Mass Up to 340 g Degree of protection IP 40 Electrical interface options Analog/Digital or CAN-bus Front panel thickness 3mm GENERAL TECHNICAL DATA 7

8 2.1 CABLES SVAB Grip L8 cable is available for both analog/digital signals as well as for CAN bus communication. It is also possible to combine analog/digital signals and CAN bus communication in the same joystick grip. ANALOG/ DIGITAL CABLE TECHNICAL DATA Info: You can choose whether L8 is to be supplied with or without analog/ digital cables. Analog/digital cable is delivered without contacting. Consult a SVAB sales representative if contacting is required. Materials Conductor Primary insulation Jacket Tin-coated copper Radiation-crosslinked, extruded polyalkene Radiation-crosslinked modified PVF 2. Thickness:.003 ±.001 in. Wire size (AWG) 24 8 GENERAL TECHNICAL DATA

9 CAN CABLE DIMENSIONS (in millimeters) Info: When choosing CAN based communication a fully assembled CAN cable is always included. L8 CAN cable has 4-pin M8 male connectors. The L8 CAN cable uses PUR cable. This cable is intended as a bonding and connection cable for high mechanical loads in industrial operation with abrasive stress. The PUR cable is fit for environments where there is a high demand of protection from chemical solvents and oil. Visible cable s length (including contact) is 90 cm. 900 Face view M8x1 GENERAL TECHNICAL DATA 9

10 3. HOLE PATTERN LAYOUT The hole pattern layout shows where the thumbwheels, push buttons and toggle switches can be placed on the front plate of the joystick grip, and the diameter of holes for pushbuttons and toggle switches. HOLE DIAMETER A Ø15,2 B Ø12 C Ø6,5 D Ø4,4 In chapter 3.1 FRONT PLATE HOLE PATTERN LAYOUT below, only the right front plate is shown. The same hole pattern layout applies to both right and left joystick grip with the difference that the left front plate is mirrored according to position numbering: FRONT PLATE LEFT FRONT PLATE RIGHT FRONT PLATE HOLE PATTERN LAYOUT 10 (right) 11 (right) 12 (right) 13 (right) 14 (right) 15 (right) 4A 5A 4A 5B 6A 4A 5A 6A 6A A A 1 2 3A 1 2 3A 16 (right) 18 (right) 19 (right) 20 (right) 21 (right) 22 (right) 4 5A 6A 4A 5C 6A 4B 5B 6A A 1 2A 3A 1 2 3A 1 2 3A A 1 2 3A 10 HOLE PATTERN LAYOUT

11 23 (right) 24 (right) 25 (right) 32 (right) 33 (right) 35 (right) A 4 5 6B 4A 5A 1 1 3A 2 3A A 1A 2A 1A 2A 3A 1A 2A 3A 36 (right) 1A (right) 26 (right) 27 (right) 28 (right) 37 (right) 4A 5A 6A 4A 5A B 1A 2A 3A 1 2 3A 1 2 3B 1 2 3B A 3A 1D (right) 39 (right) 1G (right) 1F (right) 1H (right) 1I (right) 4 5 6C 4B 7 D 4A 5B 6A 4A 5A 6C 4A 5B 4B 5A 1 2 3A 1 2 3A 1 2 3A 1 2 3A 1 2 3A 1 2 3A 1J (right) 1K (right) 1L (right) 1N (right) 1P (right) 5 D 4A 5B 6 D D 4 5B 6A 4B 5A 6A 1A 2A 3A 1 2 3A 1 2 3A 1 2A 3A 1 2 3A HOLE PATTERN LAYOUT 11

12 3.2 BACK SIDE HOLE PATTERN LAYOUT The back of the L8 grip always has the same hole pattern layout. When the holes aren t used by thumbwheel and pushbuttons, the holes are plugged. On the L8 joystick grip s back side only thumbwheels (position 4) and pushbuttons (positions 1, 2 and 3) can be positioned. BACK SIDE LEFT BACK SIDE RIGHT HOLE PATTERN LAYOUT

13 4. PROPORTIONAL THUMBWHEEL Thumbwheel SVAB HECR is our internally developed spring-loaded thumbwheel. The thumbwheel has a short rotational angle and therefore need only a relatively small influence of the thumb or finger to get full effect. THUMBWHEEL SVAB HECR TECHNICAL DATA Features: Analog and variable. Flat collar for flat surfaces. Round collar for rounder surfaces. Dual analog signals. Electrical Characteristics Supply Voltage (Vs) Supply Current 4.5 VDC min. 5.0 VDC typ. 5.5 VDC max. 14 ma typ. 20 ma max. Over/Under Voltage Protection -8.5 VDC min. 8.5 VDC max. Output Voltage (Signal 1 & 2) (Vs 0.14) (Vs/2) (Vs-(Vs 0.14)) VDC typ. Inverted value on output signal 2. Custom values available upon request. Output Voltage Mechanical & Temp. Tolerance ±0.2V max. Output Resolution Max. Recommended Output Current Short Circuit Protection 12 bit ratiometric to Vs (full scale output, 0-5 VDC) 1 ma. 10 minutes max. PROPORTINAL THUMBWHEEL 13

14 THUMBWHEEL SVAB HECR (continued) Environmental Characteristics Operating Temperature Storage Temperature EMI/RFI -40 C to 70 C. -40 C to 85 C. 100 V/m and 200 ma BCI, 150 khz to 2 GHz. EMI Output Tolerance DC 25 mt (Area 1). DC 25mT (Area 2), mounted in L8 handle. DC 25 mt (Area 3), with additional shielding* ESD Handling ESD Operating ±8 kv. ±15 kv air discharge. ±8 kv contact discharge. Output Signal Diagram Mechanical Characteristics Rotational Cycles >4,000,000 Rotational Angle ±40 Wiring Information Cvilux CI01-04S GND 2 Output signal 1 3 Output signal V 14 PROPORTINAL THUMBWHEEL

15 5. PUSHBUTTONS PUSHBUTTON STANDARD OTTO (P9) Info: TECHNICAL DATA A Ø15,2 The P9 Dome series pushbutton switches feature a contoured dome style pushbutton and share similar size and characteristics to the P7 series. Major differences are plastic housing construction and the availability of a shorting bar contact arrangement. There are two button versions: low button profile and high button profile. The P9 comes with a threaded case for hex nut mounting or with a snap-in case. The switch series features short behind panel depth. They also offer excellent mechanical and electrical performance while operating under severe conditions found in demanding applications. The buttons are specified at 5Amps/4Amps. However SVAB adds a CVI- LUX connector which lower the tolerance to 2Amps. The P9 Dome series is offered in dusttight and moistureproof sealed construction. One million mechanical operations and an electrical life of 25,000 operations at full rated load of 5 amps resistive or 3 amps inductive. Watertight sealing is available simply by adding a W suffix to the part number to specify IP68S rating. The P9 Dome series is available in standard and low-force double break snap-action and non-snap shorting bar models. All are momentary action. Special contact variations are available. High contact pressure and unique contact design provide low contact resistance for low level switching capability as well as full rated service. Solder, PC Pin, and Quick Connect termination options are available. Positive tactile feedback signaling the operator when the switch is operated is available in snap-action models but not shorting bar models. The P9 Dome series is a quality precision switch designed for use in panels, control grips, computers, instruments, heavy equipment and other demanding applications where attractive, rugged pushbutton switches are required. Features: Attractive dome style button 2 button heights Double break or shorting bar, momentary action All plastic housing & button construction Threaded body or snap-in panel mounting Withstands extreme shock & vibration Positive tactile feedback contact transfer on snap-action models Solder, PC Pin & Quick Connect terminal styles Moistureproof & dusttight to IP64 or watertight to IP68S UL recognized & CSA certified RoHS/WEEE/Reach compliant Tip! The Tall Hat -model is ideal when used as a dead man button on the SVAB Grip L8 back side. Standard Matte Electrical Ratings (sea 28VDCor 115VAC,60/400Hz) Tall Hat Load N.O./N.C 2 2 Circuit Resistive 2A (5A) 2A (4A) Inductive 2A (3A) 2A DWV Low Level Electrical Life Mechanical Life Seal Operating Temp. Range 1050Vrms 30mV 25,000 cycles 28VDC resistive snap-action 1,000,000 cycles IP64 or IP68S -40 C to +85 C Operating Force Standard: 1.7 lbs. +/- 0.5 lb. Low Force: 12 oz +/- 4 oz Shorting Bar: 18 oz +/- 6 oz Total Travel Overtravel Materials Case Button Terminals Terminal Hardware Mounting Hardware Available Button Colors inches max inches min Thermoplastic Thermoplastic Brass with gold over silver None provided Hex nut, lockwasher Panel gasket when applicable Black, Green, Gray, Red, Yellow, Blue PUSHBUTTONS 15

16 PUSHBUTTON DOUBLE PRESS ITW (48EM) TECHNICAL DATA Info: Double press ITW is our option when a distinct remaining button press is desired. When pressing the button it remains pressed down until the button is pressed again Features: Maintained action Gold contacts Long life Solder or PC terminals Panel sealed to IP 67 Circuit Button travel (nominal) Operating force (nominal) Contact bounce (nominal) Panel thickness Temperature index Current ratings (resistive) Dielectric strength Insulation resistance Contact resistance Torque (max) SPST-NO-DB A Ø15, inches / 2.3 mm 3N / 306 grams 1 millisecond inches / 0.5 3mm -40 F to F 12VDC, 100K cycles 28VDC, 150K cycles (momentary) 48VDC, 100K cycles 12VDC, 1 million cycles (momentary) 1,000 VAC 1G OHM 50 mω max (initial) 10 inch pounds 16 PUSHBUTTONS

17 6. TOGGLE SWITCHES, LEDs AND MINITRIM TOGGLE SWITCH TAIWAY (SERIES 100 SPDT) TECHNICAL DATA Info: The toggle switch is specified at 5Amps. However SVAB adds a CVILUX connector which lower the tolerance to 2Amps. C Ø6,5 Types Model No. Switching Position SP-1 ON NONE ON SP-3 ON OFF ON SP-4 (ON) OFF (ON) SP-5 ON OFF (ON) Term. Comm. 2-3 OPEN 2-1 Schematic O2Comm. Specifications Contact rating Silver plated (movable contact / Terminals: Copper alloy, silver plated). 2Amps 125VAC or 28VDC 250VAC Agency Approval: Electrical life Contact resistance Insulation resistance Dielectric strength Operating temperature 50,000 make-and-break cycles at full load. 10mΩmax. 100mA for both silver and gold plated contacts. 1,000M Ωmin. 1,500V sea level. -30 C to +85 C Materials Case Toggle handle Bushing Housing Terminal seal Actuator cap material Diallyl phthalate(dap)(ul 94V-0) Brass, chrome plated. Brass, nickel plated. Stainless steel. Epoxy. PVC (red) TOGGLE SWITCHES, LED:S AND MINITRIM 17

18 TOGGLE SWITCH SMG TECHNICAL DATA B Ø12 Types Model No. Switching Position V7 ON OFF ON V6 (ON) OFF (ON) Specifications Rating Initial contact resistance Insulation resistance Dielectric strength Endurance (Electrical life) Endurance (Mechanical life) Water proofing Lever strength Operating force Accessory 50mA 28V DC 20mΩ max. at 1.5mA 200µV AC (1kHz) 1,000MΩ min. at 500V DC. (between terminals and terminals and earth) 1,000V AC(between terminals). 1,500V AC(between terminals and earth) for 1 minute. No damage electrical and mechanical function after 25,000 cycles (20 cycles/minute) at the rating. No damage electrical and mechanical function after 100,000 cycles (20 cycles/minute) at no load. 30 minutes at 1 meter water column : IP N applied to the top of lever side from 90 degree angle of lever axis 0.49~7.85N(50~800gf) Cap and screw: Each one piece attached. Materials Case Common terminal Fixed terminal Frame Bushing Cap Screw O Ring Diallyl phthalate resin (green) Phosphor bronze, silver plated Copper, silver plater Stainless steel Brass, nickel plated Polybutylene terephalate Brass, nickel plated Nitril rubber 18 TOGGLE SWITCHES, LED:S AND MINITRIM

19 PUSHBUTTON LED BUTTON APEM (IP) TECHNICAL DATA NOTE! The APEM LED button may require a unique solution to be integrated with the machine or system. Always consult a SVAB sales representative before the selection of the LED button is made. Info: The APEM LED button can be used when you want to signal that a function has an on or off state. This by the LED remaining lit while the function is still active. The pushbutton is specified at 5Amps. However SVAB adds a CVILUX connector which lower the tolerance to 2Amps. Features: Illuminated (LED). Tactile feedback. Flat round actuator for optional marking. Sealed to IP67. Environmental specifications A Ø15,2 Front panel sealing IP67 according to IEC Shock resistance 100 g according to IEC 512-4, test 6c Vibration resistance Hz - 10 g according to IEC 512-4, test 6d Salt spray Operating temperature Electrical specifications IEC 512-6, test 11f -40 C to +85 C Max. current/voltage rating with resistive load (gold plated silver contacts) Initial contact resistance Insulation resistance Dielectric strength Contact bounce Green LED (A resistor must be seriesconnected by the user. 2A (5A) 28VDC, cycles 0,2A 48VDC, cycles 0,5A 48VAC, cycles 100 mω max. 1 GΩ min. at 500VDC Vrms 10 ms Forward current: 20mA Typ. forward voltage: 2,1V Max. forward voltage: 2,3V Resistor value = supply voltage (minus) LED forward voltage (divided by) LED forward current General specifications Panel thickness Total travel Typical operating force Mechanical life Torque Soldering 1,5 mm (.059) min. 4 mm (.157 max.) Funct. 3 : 1,7 mm (.067) +/- 0,3 mm Funct. 5 : 1,3 mm (.051) +/- 0,3 mm 6N +/- 2N cycles 1,5 Nm max. applied to nut 320 C max. for 3 sec. TOGGLE SWITCHES, LED:S AND MINITRIM 19

20 PUSHBUTTON LED BUTTON APEM (continued) Materials Case thermoplastic UL94-V0 Actuator polyamide 6/6 Bushing/bezel Contacts Multi-wire lead LED wire Lens Terminal seal Available button color zinc die-cast (zamac), black painted silver, gold plated AWG20, section 0,6 mm² AWG26, section 0,12 mm2 polycarbonate epoxy Black Agency approval 2A 125VAC/250VAC File E83438 Availability Marking consult factory for details of approved models. to order switches marked UL, complete ordering format LED 5V, 12V, 24V TECHNICAL DATA NOTE! The L8 LED may require a unique solution to be integrated with the machine or system. Always consult a SVAB sales representative before the selection of an LED is made. D Ø4,4 Info: The LED can be used when you want to signal that a function has an on or off state. This by the LED remaining lit while the function is still active. Light Color Wavelength (top) Brightness Forward Voltage Capsule Capsule Color Capsule Type Beam angle Forward Voltage Nominal Technology Green 565 nm mcd 5V, 12V 3mm (T1) Green Diffuse 40 (5V)12mA, (12V)11mA GaP 20 TOGGLE SWITCHES, LED:S AND MINITRIM

21 MINITRIM OTTO T8 TECHNICAL DATA NOTE! Minitrim may require a unique solution to be integrated with the machine or system. Always consult a SVAB sales representative before the selection of the Minitrim is made. The Minitrim does not occur in any of the hole pattern layouts and thereby cannot be configured in the product configuration code. Contact a SVAB sales representative if you are interested in Minitrim OTTO. Info: OTTO Minitrim gives the L8 joystick grip an additional digital XY mini joystick on the front plate of the L8 joystick grip. For more information on alternative Minitrim button styles, see ottoexcellence.com. Electrical Ratings Load Resistive Inductive DWV Low Level Electrical Life Lever Travel Rating 5VDC (low level) 28VDC 1050Vrms 10mA 5VDC 100,000 cycles 1A 28VDC Toggle: 15 max from center OFF Seal IP64 or IP68S or MIL-PRF-8805 Design 3 Operating Temp Range Operating Force Lever Pivot & Stop Strength -55 C to +85 C Toggle: 16 oz +/- 6 oz Switch is capable of withstanding a force of 25.0 lbs. applied to the actuating button. The button also withstands 15.0 lbs. minimum pull force. Materials Case Button Terminals Terminal Hardware Mounting Hardware Aluminum alloy or thermoplastic Thermoplastic Silver over brass Brass with gold over silver for low level None provided Hex nut, tooth lockwasher, panel seal gasket where applicable TOGGLE SWITCHES, LED:S AND MINITRIM 21

22 7. MOUNTINGS The L8 joystick grip is attached on the joystick base with mountings and accessories. Mountings and accessories allows the joystick grip to be fitted on a large variety of joystick bases. STANDARD DIMENSIONS (in millimeter) NOTE! Accessories for mountings, like the adapter ball kit, is sold separately. See ADAPTER BALL KIT FOR STANDARD MOUNTING L8 on page 27. Info: Standard mounting that with the help of accessories fit a wide range of joystick bases. 22 ATTACHMENTS

23 OPTION 1 DIMENSIONS (in millimeter) Info: A Option 1 has been developed for Penny + Giles joystick base JC6000 but it can also fit other brands of joystick bases. R A Option 1 is fitted directly on the JC6000 joystick base. 0 23,90-0, , ,90 6 2,4 SECTION A-A M5(2x) 9 ATTACHMENTS 23

24 8. PRODUCT CONFIGURATION CODE The product configuration code allows you to configure and specify your L8 joystick grip so that we at SVAB quickly and efficiently can meet your requirements. Accessories (page 26) such as bellow washers and adapter kits are not included in the product configuration code. The accessories are ordered separately. E F * Positions 1-4 refers to the joystick grips back side as shown below (8.1 L8 JOYSTICK GRIP POSITIONS). Here, a thumbwheel and pushbuttons can be placed. D F G Positions 1-6 refers to the joystick grip front plates six different positions as shown below (8.1 L8 JOYSTICK GRIP POSITIONS). Here, thumbwheels, pushbuttons and toggle switches can be placed according to the selected hole pattern layout (as seen in table C on page 25). In each position the first and second letter specifies the component code (as seen on page 25). With the third letter you specify whether the thumbwheel, pushbutton or toggle switch communicates via analog/digital (A) or SVAB CAN-bus (C) communication. SVAB CAN-bus requires a control system from SVAB. In each position the first and second letter specifies the component code (as seen on page 25). With the third letter you specify whether the thumbwheel or pushbutton communicates via analog/digital (A) or SVAB CAN-bus (C) communication. SVAB CAN-bus requires a control system from SVAB. # indicates that the position is not used and thereby replaced by a plug. NOTE! The back side position 3 cannot be plugged and must therefore contain a pushbutton or a toggle switch. A B C # indicates that the position is occupied by a thumbwheel. A thumbwheel always occupies two positions. * The back side position 3 can also be fitted with the TAIWAY toggle switch (V1-V4). L 8 R 0 / 1 N / P 1 C A A - # # # - V 7 C A / 0 1 A - # # # A - P 1 C / H Position front plate Position back side 8.1 L8 JOYSTICK GRIP POSITIONS FRONT PLATE LEFT BACK SIDE LEFT BACK SIDE RIGHT FRONT PLATE RIGHT PRODUCT CONFIGURATION CODE

25 This symbol indicates that more information is found on the referred to page. A Right or left joystick grip ( 6) Code L8 R L8 L Description Right grip Left grip B Grip color ( 6) Code Description 0 Gray 1 Black C Hole pattern layout for thumbwheels (TW), pushbuttons and toggle switches on the front plate ( 10) Code Description TW TW, 3A TW, 4A, 5A TW, 4A, 5B, 6A TW, 3A, 4A, 5A, 6A TW, 3A, 6A TW, 2A, 3A, 5A, 6A TW, 3A, 4A, 5C, 6A TW, 3A, 4B, 5B, 6A TW, 4-5 TW TW, 3A, 4-5 TW TW, 3A, 4-5 TW, 6A Code Description TW, 2-5 TW, 3A TW, 2-5 TW, 3A, 6A TW, 3A, 4-5 TW, 6B 32 1A, 2A 33 1A, 2A, 3A 35 1A, 2A, 3A, 4A, 5A 36 1A, 2A, 3A, 4A, 5A, 6A 1A 1-2 TW, 3A, 4A, 5A TW, 3B, 4-5 TW TW, 2-5 TW, 3B TW, 3A TW, 3A, 5B Code Description 1D 1-4 TW, 2-5 TW, 3A, 6C TW, 3A, 4B 1G 1F 1H 1I 1J 1K 1L 1N 1P 1-2 TW, 3A, 4A, 5B, 6A, 7D 1-2 TW, 3A, 4A, 5A, 6C 1-2 TW, 3A, 4A, 5B 1-2 TW, 3A, 4B, 5A 1A, 2A, 3A, 5D 1-2 TW, 3A, 4A, 5B, 6D 1-2 TW, 3A, 2-4 TW, 6D 1-4 TW, 2A, 3A, 5B, 6A 1-2 TW, 3A, 4B, 5A, 6A This table shows the positions (1-6) of thumbwheels, pushbuttons and toggle switches in the hole pattern layout according to 8.1 L8 JOYSTICK GRIP POSITIONS. The letters A, B, C and D indicates hole diameter ( 10). D Front plate thumbwheels ( 13) Code Description P1_ HECR 0,7-4,3 VDC Q1_ HECR 0-5 VDC Q2_ HECR 0,5-4,5 VDC Q3_ HECR 1,35-3,65 VDC E Back side thumbwheel ( 13) Code Description R1_ HECR 0,7-4,3 VDC S1_ HECR 0-5 VDC S2_ HECR 0,5-4,5 VDC S3_ HECR 1,35-3,65 VDC F Pushbuttons ( 15) Code Description 01_ Button std. OTTO (P9), black - Diameter: A 12_ Button double press ITW (48EM) - Diameter: A 13_ Button OTTO (P9), green - Diameter: A 14_ Button OTTO (P9), gray - Diameter: A 15_ Button OTTO (P9), red - Diameter: A 16_ Button OTTO (P9), yellow - Diameter: A 17_ Button OTTO (P9), blue - Diameter: A 18_ Button OTTO (P9), Tall Hat - Diameter: A H Mountings ( 22) Code Description 01 Standard NOTE! accessories my be required in order to fit the grip on the joystick base with the standard mounting, see 9.1 ADAPTER BALL KIT FOR STAN- DARD MOUNTING L8 page Option 1 G Toggle switches, LEDs and minitrim ( 17) Code Description V1_ Switch TAIWAY SP Diameter: C V2_ Switch TAIWAY SP Diameter: C V3_ Switch TAIWAY SP4 (1)-0-(1) - Diameter: C V4_ Switch TAIWAY SP5 1-0-(1) - Diameter: C V6_ Switch SMG (1)-0-(1) - Diameter: B V7_ Switch SMG Diameter: B 19_ Knapp APEM with green LED - Diameter: A V9_ LED, green, 5V - Diameter: D V0_ LED, green. 12V - Diameter: D VB_ OTTO Minitrim T8 NOTE! Minitrim does not exist in any layout and cannot be configured in the product configuration code. Contact SVAB if you are interested in the minitrim. PRODUCT CONFIGURATION CODE 25

26 9. ACCESSORIES Accessories allows the SVAB Grip L8 joystick grip to be fitted on market joystick bases. Among the accessories, bellow washers and adapters can be found which facilitates the attachment of the joystick base bellow to the joystick grip. Accessories are ordered separately and are not included in the product configuration code (page 24). 26 ACCESSORIES

27 9.1 ADAPTER BALL KIT FOR STANDARD MOUNTING L8 The ball head screw allows attachment of the L8 joystick grip to the joystick base with the use of a locking plate. ADAPTER BALL KIT FOR STANDARD MOUNTING L8 DIMENSIONS (in millimeter) Info: This kit is compatible with the L8 joystick grip standard mounting (page 22). 8 The kit includes ball screws, locking plate and screws for the locking plate. The kit comes with three different standard size screws for attachment to the joystick base. M12, M14 and m14x1, Ordering information Description Article no. Adapter ball kit L8 M12, M14 & M14x1, ACCESSORIES 27

28 9.2 BELLOW WASHERS Bellow washers allows for the attachment of the joystick base bellow to the L8 joystick grip. STANDARD BELLOW WASHER FOR STANDARD MOUNTING DIMENSIONS (in millimeter) Info: R Bellow washer in spring steel for Standard mounting (page 22). Enables the attachment of the joystick base bellow to the L8 joystick grip. 4 R3,50 10,80 Ordering information Description Article no. Bellow washer with screws ACCESSORIES

29 9.3 BELLOW ADAPTERS FOR STANDARD BELLOW WASHER If the joystick bases upper bellow hole is too large to fit the standard bellow washer, a bellow adapter may be required. The bellow adapter allows for attaching bellows with large upper holes to the L8 joystick grip. Contact SVAB if you do not find a suitable measure among existing bellow adapters. BELLOW ADAPTER D76 FOR STANDARD BELLOW WASHER DIMENSIONS (in millimeter) Info: 6 The bellow adapter allows for attaching bellows with large upper holes to the L8 joystick grip. Black POM plastic. 76 A A SECTION A-A 3xR 0,50 44, ,50 2,50 1,50 56 Ordering information Description Article No. Bellow adapter L8 D ACCESSORIES 29

30 R20 BELLOW ADAPTER 65x81 FOR STANDARD BELLOW WASHER Info: DIMENSIONS (in millimeter) A The bellow adapter allows for attaching bellows with large upper holes to the L8 joystick grip. Black POM plastic. A 32, , SECTION A-A Ordering information Description Article No. Bellow adapter L8 65x ACCESSORIES

31 SVAB Hydraulik AB has extensive experience in hydraulics, control electronics and ergonomic design for industrial vehicles, with guaranteed quality production and prompt delivery. SVAB Hydraulik AB Ulvsättersgatan 2 SE HALLSBERG SWEDEN Phone: +46 (0) Fax: +46 (0) info@svab.se Web:

32