Main Unit AC or DC power

Transcription

1 Main Unit AC or DC power General Specification /DC /DC XEC-DR32H XEC-DN32H Ambient temperature Storage temperature Ambient humidity Storage humidity Vibration resistance Shock resistance Noise resistance Operating Ambience Altitude ollution level *1) Cooling Descriptions 0 ~ 55 C 25 ~ + 70 C 5 ~ 95%RH (Non-condensing) 5 ~ 95%RH (Non-condensing) Ocnasional vibration Frequency 10 f < 57Hz 57 f 150Hz Acceleration 9.8m/s2 (1G) ulse width 0.075mm Continuous vibration Frequency Acceleration ulse width 10 f < 57Hz 0.035mm 57 f 150Hz 4.9m/s2 (0.5G) 10 times each direction (X, Y and Z) eak Acceleration: 147m/s2 (15g) Duration: 11ms ulse waveform: Half-sine, 3times each direction per each axis Square wave impulse noise 1,500 V Electrostatic discharge 4kV Radiated 80 ~ 1000 MHz, 10V/m lectromagnetic field noise Main unit Expansion module Fast transient/ Burst noise 2kV 1kV Free from corrosive gases and excessive dust Up to 2,000m Less than 2 Air-cooling Standard IEC IEC LSIS Standard IEC / IEC IEC / IEC IEC / IEC *1) ollution level indicates the degree to which conductive material is generated in the environment where the equipment is used. ollution level 2 is the condition that only non-conductive pollution occurred but temporary conductivity may be produced due to condensing. erformance Specification /DC /DC XEC-DRH XEC-DNH Control method I/O control mode rogramming language rocessing speed rogram capacity Max. I/O points Number of program Operation mode Self diagnosis rogram port Data retension at power failure Built-in function RTC Internal current consumption Weight Rated voltage M K L F T C S D U Z N XEC-DR32H *1) /DC XEC-DN32H *1) /DC XEC-DRH *1) /DC Repetitive, cyclic, interrupt, constant scan Refresh mode (Batch processing by scan synchronization) Direct mode by instruction Ladder diagram or IEC standard (LD, SFC, ST) *1) 83ns / Step (for basic instruction) 15k step (IEC type 200KB) XEC-DNH *1) /DC 352 points(main + 10 expansions) 384 points (Main + 10 expansions) 128 RUN, STO, DEBUG Operation delay monitoring, memory error, I/O error, battery error, power error, etc. USB (Rev 1.1), RS-232C Latch range setting at Basic parameter RS-232C / 485, High-speed counter, ID control, ulse catch, Input filter External interrupt, ositioning Built-in 6mA 0g XBC 0000 ~ 1023F (16,384 points) M0000 ~ M1023F (16,384 points) K0000 ~ K4095F(Special area: K20~2559F) (65,536 points) L00000 ~ L2047F (32,768 points) F000 ~ F1023F (16,384 points) 100ms, 10ms, 1ms: T000 ~ T1023(Changeable by arameter setting) C000 ~ C1023 S00.00 ~ S D0000 ~ D10239 (10,240 word) U00.00 ~ U0A.31 (Analog data refresh area: 352) Z000 ~ Z127 (128 word) N0000 ~ N5119 (5,120 word) 2mA 1040mA 500g 0g AC 100 ~ or DC24V Data memory XEC(IEC type) Symbolic variablearea (A) Input variable (I) Output variable (Q) Direct variable Flag variable Flash area M R W F K L N U 330mA 800g 32KB (Max.16K byte retain setting available) 2KB (%IX ) 2KB (%QX ) 16KB (Max.8K byte retain setting available) 20KB (1block) 20KB 2KB 8KB 4KB 10KB 1KB 20KB, 2blocks (Using R device) *1) Only main unit for IEC standard language 10

2 rogrammable Logic Controller Names and Functions No. Input LED Condition LED Output LED Name Descriptions Descritpions Remark Expansion module connector ADT connector Mode switch Input Terminal block Output Terminal block Built-in RS-485 connector Built-in RS-232C connector ower terminal Input indication WR: ower indication RUN: RUN indication ERR: Error indication Output LED Expansion module connector ADT connection Mode setting Input wiring connection Ouput wiring connection Built-in RS-485 connection Built-in RS-232C connection ower supply terminal Red On: Input signal On Red Off: Input signal Off Red On: ower On Red Off: ower Off Green On: LC Run Green Off: LC Stop Red On-and-Off: LC Error Red Off: LC Normal condition On: Output signal On Off: Output signal Off Connection of expansion module (I/O, Special function, Communication) Connector for XG5000 / XG-D connection Setting Run/Stop mode of LC RS /-terminal connection RS-232C TD, RD, SG terminal connection AC V power supply Input Specification Input points Rated input voltage Rated input current Operation voltage range On voltage / On current Off voltage / Off current Input resistance Off On On Off Weight XEC-DR32H XEC-DN32H XEC-DRH DC 24V 4mA (Contact 0~7: 9mA) DC 20.4 ~ 28.8V (Ripple rate < 5%) DC 19V or more / 3mA or more DC 6V or less / 1mA or less 5.6k(00 ~ 07: 2.7k) XEC-DNH 1 / 3 / 5 / 10 / 20 / 70 / 100 ms (Setting by CU parameter) Initial value: 3ms 0g 500g 0g 800g Relay output specification Output point Insulation method Rated load voltage / current Min. load voltage / current Max. load voltage Off leakage current Max. On / Off frequency Mechanical Service life Common method Electrical Off On On Off /XEC-DR32H Relay insulation /XEC-DRH DC 24V 2A (Resistive load) / AC 220V 2A (COS = 1), 5A / COM DC 5V / 1mA AC 250V, DC 125V 0.1mA (AC 220V, Hz) 3,0 times / hr 20millions times or more Rated load voltage / current 100,000 times or more AC 200V / 1.5A, AC / 1A (COS = 0.7) 100,000 times or more AC 200V / 1A, AC / 0.5A (COS = 0.35) 100,000 times or more DC 24V / 1A, DC 100V / 0.1A (L / R = 7ms) 100,000 times or more 10ms or less 12ms or less 4 points / COM 20 ~ 2F: 4 points / COM 30 ~ 3F: 8 points / COM 11

3 Main Unit AC power Transistor output specification Output point Insulation method Rated load voltage Load voltage range Max. load voltage Off leakage current Max. inrush current Max. voltage drop (On) Surge absorber Off On On Off Common method External power supply Voltage Current /XEC-DN32H /XEC-DNH hoto coupler insulation DC 12 / 24V DC 10.2 ~ 26.4 V 0.5A / 1point ( 20 ~ 23: 0.1A / point) 0.1mA or less 4A / 10ms or less DC 0.4V or less Zener Diode 1ms or less 1ms or less (Rated load, resistive load) 20 ~ 2F: 4 points / COM 4 points / com 30 ~ 3F: 8 points / COM DC 12 / 24V 10% (ripple voltage 4 Vp-p or less) 10mA or less (DC 24V connection) Input wiring ( / XEC-DR32H / XEC-DN32H) RX TX SG B 0D 0F 24G A OC OE COM 24V Input wiring ( / XEC-DRH / XEC-DNH) RX TX SG B 0D OF NC B 1D 1F 24G A 0C 0E COM A 1C 1E COM1 24V Relay output wiring (/XEC-DR32H) COMO A COM2 2D 2F NC COM1 29 2B 2C 2E COM3 12

4 rogrammable Logic Controller Transistor output Wiring (/XEC-DN32H) COMO A COM2 2D 2F COM1 29 2B 2C 2E COM3 Relay output Wiring (/XEC-DRH) AC COM A COM2 2D 2F COM4 39 3B 3D 3F NC COM1 29 2B 2C 2E COM A 3C 3E COM5 Transistor output wiring (/XEC-DNH) COM A COM2 2D 2F COM4 39 3B 3D 3F COM1 29 2B 2C 2E COM A 3C 3E COM5 13

5 Dimension Download cable diagram Dimension W (Unit: mm) Model Length /DN32H W 114 XEC-DR32H/DN32H Model Length /DNH W 180 XEC-DRH/DNH Model W H D XBM Main unit 30 DR/DN32H (32pt) 114 XBC/XEC DR/DNH (pt) 180 RY output / EMTA 27 DC input Common TR output 20 Analog 34