1-DC SERIES PANEL MOUNT

Transcription

1 1DC SERIES PANEL MOUNT Features Ratings from 6 A to 1 1 DC Mosfet Output UL Approved, CE Compliant to EN6951 Improved SEMS screw and washer Redesigned housing with antirotation barriers DC control EMC Compliant to Level 3 Epoxy Free Design PRODUCT SELECTION Control oltage 6 A 8 A 1 A DC D1D6 D1D8 D1D1 Output (2) SPECIFICATIONS Description 7 A 12A 2A Recommended Operating oltage [dc] Absolute Maximum Rating [dc] Maximum OffState Leakage Rated oltage [ma] Maximum Load Current [Adc] (1), (3) Minimum Load Current [ma] () Maximum Surge Current (1msec) [Adc] Maximum OnState oltage Rated Current [dc] Maximum OnState Resistance [RDSON] [Ohms] Thermal Resistance Junction to Case (Rjc) [ C/W] Minimum Heat Sink for Rated C [ C/W] Maximum Pulse Width Modulation Frequency [Hz] (5) Page 1

2 Input (2) Description DC Control Control oltage Range DC Maximum Reverse oltage 32 DC Minimum TurnOn oltage (6) 3.5 DC Must TurnOff oltage 1 DC Minimum Input Current (for onstate) 1 ma Maximum Input Current 15 ma Nominal Input Impedance Current Regulated Maximum TurnOn Time [μsec] 1 Maximum TurnOff Time [μsec] 1 General (2) Description Parameters Dielectric Strength, Input/Output/Base (5/6Hz) Minimum Insulation Resistance (@ 5 DC) Maximum Capacitance, Input/Output 375 rms 1 9 Ohms 8 pf Ambient Operating Temperature Range (7) to 1 C Ambient Storage Temperature Range to 125 C Weight (typical) 2.66 oz (75.5 g) Housing Material UL9 Baseplate Material Aluminum Input Terminal Screw Torque Range (inlb/nm) 1315 / Load Terminal Screw Torque Range (inlb/nm) 182 / 22.2 SSR Mounting Screw Torque Range (inlb/nm) 182 / 22.2 Input/Load Terminal Screw Torque Range (inlb/ Nm) 1 w/ K option 81 / Input/Output Terminal Screw Thread Size Humidity per IEC MTBF (Mean Time Between Failures) at C ambient temperature (8) MTBF (Mean Time Between Failures) at 6 C ambient temperature (8) #632 UNC / #832 UNC 93% noncondensing 21,395,13 hours (2,1 years) 11,55,5 hours (1,317 years) Page 2

3 WIRING DIAGRAM * Inductive loads must be diode suppressed. Recommended Wire Sizes Load * * Load Terminals Wire Size (Solid / Stranded) Wire PullOut Strength (lbs)[n] 1 OUTPUT SO LI D STAT E RE LA Y 2 1 OUTPUT SO LI D STAT E RE LA Y 2 Input 2 AWG (.2 mm 2 ) /.2 [minimum] 2 x 12 AWG (3.3 mm 2 ) / 3.3 [maximum] 1 [.5] 9 [] INPUT 3 INPUT 3 Output 2 AWG (.5 mm 2 ) /.518 [minimum] 2 x 1 AWG (5.3 mm 2 ) / x 8 AWG (8. mm 2 ) / 8. [maximum] 3 [133] 11 [9] 9 [] EQUIALENT CIRCUIT BLOCK DIAGRAMS DC 3 2 DC 1 12 Input Current vs Input oltage Standard Regulated DC Inputs DC Control Circuit Trigger Circuit 1 DC Input Current (ma) DC Input oltage MECHANICAL SPECIFICATIONS (2) *Tolerances: ±.2 in /.5 mm All dimensions are in: inches [millimeters] Screw Termination Hex Standoff Termination ( K Option) [27.9].9 [12.] Mounting Hole/Slot.19 [.9] DIA..89 [22.6] 1.1 [27.9].9 [12.] Mounting Hole/Slot.19 [.9] DIA. 1. [26.] (2 places) 1 OUTPUT 2 1 OUTPUT [7.6] SO LI D STAT E RE LA Y INPUT [3.2] 2.25 [57.3] 1.88 [7.6] SO LI D STAT E RE LA Y INPUT [3.2] 2.25 [57.3] 1. [25.] 1.75 [.5] 1. [25.] 1.75 [.5].93 [23.6] ( places) 1. [25.] (2 places) Page 3

4 SURGE CURRENT INFORMATION Surge Current (Amp) D1D Surge Duration (msec ) Surge Current (Amp) D1D Surge Duration (msec ) 8 D1D1 Surge Current (Amp) Surge Duration (msec ) Duty Factor 1% Duty Factor 2% Duty Factor 5% Pu lse Wide Pe riod For Pulse Wide Modulation applications select the curve according duty factor and pulse duration as following. =Duty Factor Pulse Wide Period (i) for Single Surge Pulse Tc= C ;Tj 175 C (ii) for Repetitive Surge Pulse Tc= C ;Tj 13 C x1 (%) THERMAL DERATE INFORMATION 6 D1D6 1 C/W 2 C/W 5 C/W 8 D1D8.5 C/W 1.5 C/W 3 C/W 5 C/W Load Current (Amps) 2 Load Current (Amps) Ambient Temperature (ºC) Ambient Temperature (ºC) Load Current (Amps) D1D1.5 C/W 1.5 C/W 3 C/W 5 C/W Ambient Temperature (ºC) Page

5 ACCESSORIES New Accessories! Protective Cover & Hardware Kits Protective Cover Part number: KS11 Clear plastic cover compatible with all new S1 designs. Safety covers provide added protection from electric shock when installing or checking equipment. Hardware Kit Part number: HK Bag with 2 square brass accessories and 2 screw 832 x 5/8 for output. Used to mount TMR1 lug terminals. Recommended Accessories Thermal Cover Hardware Kit Heat Sink Part No. Resistance [ºC/W] Lug Terminal Thermal Pad KS11 HK1 HK HS51DR HS31 / HS31DR HS251 HS21 / HS21DR HS22 / HS22DR HS172 HS151 / HS151DR HS122 / HS122DR HS13 / HS13DR HS11 HS73 HS72 HS53 HS33 HS TRM1 TRM6 HSP1 HSP2 Page 5

6 ORDERING OPTIONS Example : D!D7K Not all part number combinations are available. Contact Crydom Technical Support for information on the availability of a specific part number. Family D Operating oltage 1D: 11 DC Rated Load Current 6: 6 Amps 8: 8 Amps 1: 1 Amps Termination Blank D 1D 6 K Blank: Screws & clamps K: Installed standoffs with 1 screws for PC Board mounting Required for valid part number For options only and not required for valid part number GENERAL NOTES (1) Option K is designed and tested for use with printed circuit boards or ring/fork terminals having a thickness between.31 and.93 inches (.79 to 2.36 mm), and loads rated up to 5 Amps. For higher load currents, the K standoff temperature must not exceed 15 C. For additional application assistance please contact Crydom Technical Support. (2) All parameters at Tc=25 C unless otherwise specified. (3) Heat sinking required, see derating curves. () Low current loads and high ambient temperature can affect turnon time. (5) 8 DC Minimum control voltage. Resistive loads only. Consider switching losses; at maximum frequency reduce to 75% output current. (6) Increase minimum voltage by 1 for operations from 2 to C. (7) Decrease maximum control voltage 1.35/ C above 8 C ambient temperature. (8) All parameters at 5% power rating and 1% duty cycle (contact Crydom tech support for detailed report). For additional information or specific questions, contact Crydom Technical Support Page 6

7 AGENCY APPROALS & CERTIFICATIONS EN6951: Meets the requirements of sections1.5: 1,7: 2.9: :.2:.5:.7: IEC 612 Electrostatic Discharge Level 3 IEC 61 Electrically Fast Transients Level 3 IEC 615 Electrical Surges Level 3 E11695 WARNINGS RISK OF MATERIAL DAMAGE AND HOT ENCLOSURE The product s side panels may be hot, allow the product to cool before touching Follow proper mounting instructions including torque values Do not allow liquids or foreign objects to enter this product Failure to follow these instructions can result in serious injury, or equipment damage. HAZARD OF ELECTRIC SHOCK, EXPLOSION OR ARC FLASH Disconnect all power before installing or working with this equipment erify all connections and replace all covers before turning on power Failure to follow these instructions will result in death or serious injury. Page 7 Sensata Technologies, Inc. ( Sensata ) data sheets are solely intended to assist designers ( Buyers ) who are developing systems that incorporate Sensata products (also referred to herein as components ). Buyer understands and agrees that Buyer remains responsible for using its independent analysis, evaluation and judgment in designing Buyer s systems and products. Sensata data sheets have been created using standard laboratory conditions and engineering practices. Sensata has not conducted any testing other than that specifically described in the published documentation for a particular data sheet. Sensata may make corrections, enhancements, improvements and other changes to its data sheets or components without notice. Buyers are authorized to use Sensata data sheets with the Sensata component(s) identified in each particular data sheet. HOWEER, NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE TO ANY OTHER SENSATA INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY THIRD PARTY TECHNOLOGY OR INTELLECTUAL PROPERTY RIGHT, IS GRANTED HEREIN. SENSATA DATA SHEETS ARE PROIDED AS IS. SENSATA MAKES NO WARRANTIES OR REPRESENTATIONS WITH REGARD TO THE DATA SHEETS OR USE OF THE DATA SHEETS, EXPRESS, IMPLIED OR STATUTORY, INCLUDING ACCURACY OR COMPLETENESS. SENSATA DISCLAIMS ANY WARRANTY OF TITLE AND ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, QUIET ENJOYMENT, QUIET POSSESSION, AND NONINFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL PROPERTY RIGHTS WITH REGARD TO SENSATA DATA SHEETS OR USE THEREOF. All products are sold subject to Sensata s terms and conditions of sale supplied at SENSATA ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR THE DESIGN OF BUYERS PRODUCTS. BUYER ACKNOWLEDGES AND AGREES THAT IT IS SOLELY RESPONSIBLE FOR COMPLIANCE WITH ALL LEGAL, REGULATORY AND SAFETYRELATED REQUIREMENTS CONCERNING ITS PRODUCTS, AND ANY USE OF SENSATA COMPONENTS IN ITS APPLICATIONS, NOTWITHSTANDING ANY APPLICATIONSRELATED INFORMATION OR SUPPORT THAT MAY BE PROIDED BY SENSATA. Mailing Address: Sensata Technologies, Inc., 529 Pleasant Street, Attleboro, MA 273, USA. Rev. 3/29/18 ECN 2395 FDE71 Rev. B CONTACT US Americas 1 (877) sales.crydom@sensata.com Europe, Middle East & Africa (122) 1617 ssrinfo.eu@sensata.com Asia Pacific sales.isasia@list.sensata.com China 86 (21) Japan 81 (5) Korea 82 (31) 61 2 India 91 (8) Rest of Asia 886 (2) ext 288