ION219-A 19-Slot Chassis ION219-D 19-Slot Chassis

Transcription

1 ION219-A 19-Slot Chassis ION219-D 19-Slot Chassis B Transition Networks Red Circle Drive Minnetonka MN Toll free U.S.A & Canada:

2 Transition Network Intentionally Blank 24-Hour Technical Support: International: ii

3 Table of contents Section l... 1 Introduction... 1 About this product and manual...2 Section ll... 3 Cautions & Warnings... 3 Caution and warning notices...4 Section lll... 6 Chassis Description... 6 Unpacking the chassis...7 ION219-A chassis description...8 Section IV ION219-A chassis installation Installation overview...11 Site requirements...13 Installation...15 Section V Chassis Slide-In Cards (SICs) Chassis slide-in cards (SIC)...22 Management module SIC...23 Installing SICs in chassis...24 Replacing SlCs...25 Section VI Chassis Power Chassis power LEDs...27 Powering the ION219-A chassis...28 AC power supply module...30 Replacing AC power supply fuse...31 Replacing the power supply module...32 Powering the ION219-D chassis...35 Replacing DC power supply fuse...39 Replacing the DC power supply...40 Optional AC or DC power supply module...42 Section VII Network Connectivity Connecting chassis SICs to the network...46 Network management...47 Section VIII Troubleshooting Problem corrective action table...48 Section IX Customer Information Contact us...50 Declaration of conformity...51 Warranty...52 Compliance information...54 Appendix A ION219-A chassis technical specifications...56 Appendix B Cable specification and connectors...57 Index Hour Technical Support: International: iii

4 Trademark and copyright information Trademark All trademarks and registered trademarks are the property of their respective owners. Copyright restrictions 2010 Transition Networks: All rights reserved. No part of this work may be reproduced or used in any form, or by any means (graphic, electronic, or mechanical) without written permission from Transition Networks. Printed in the U.S.A. FCC warning This equipment has been tested and found to comply with the limits for class A devices, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a commercial installation. This equipment generates, uses, and radiates radio frequency energy; therefore, if not installed and used in accordance with the instructions in this document, the device could cause harmful interference with radio communications. Operation of this equipment in a residential area is likely to cause harmful interference; all customers will be required to correct the interference problem at their expense. CE marking This is a Class A product. In a domestic environment, this product could cause radio interference; as a result, the customer may be required to take adequate preventative measures. UL recognized Tested and recognized by the Underwriters Laboratories, Inc. 24-Hour Technical Support: International: iv

5 Section l Introduction In this section This is the topic: Topic See Page About this product and manual 2 24-Hour Technical Support: International:

6 About this product and manual About the ION219-A chassis The Transition Networks ION219-A is an all new intelligent, high-density, multiprotocol 19- inch, rack-mountable chassis system that supports a variety of network interface devices ( NIDs) and media conversion. About this manual This manual provides instructions on how to install and configure the ION219-A Chassis to accommodate various types of slide-in cards (SICs). Manual structure This manual has a table of contents, a beginning of each section table of contents, and an index. As you go through the manual note, the side headings (left side of page). These side headings support quick navigation to specific content. The manual sections are as follows: Section I II III IV V VI VII VIII IX Appendix A Appendix B Index Description Introduction Cautions & Warnings Chassis Description Installation Chassis Slide-In Card Chassis Power Network Connectivity Troubleshooting Customer Information Technical Specifications Cable Specifications Navigation 24-Hour Technical Support: International:

7 Section ll Cautions & Warnings In this section This is the topic Topic See Page Caution and warning notices 4 24-Hour Technical Support: International:

8 Caution and warning notices Caution and warning definitions Caution means there is the possibility of poor equipment performance or damage to the equipment. Warning means that there is the possibility of injury or death to persons. The symbols below identify cautions and warnings. CAUTION WARNING Cautions and Warnings appear here and may appear throughout this manual where appropriate. Failure to read and understand the information identified by the caution and warning symbol could result injury to persons, poor equipment performance, or damage to the equipment. Caution Wear a grounding device and observe electrostatic discharge precautions when installing the management module(s) in the ION chassis. Failure to observe this caution could result in damage to or failure of the management module. Caution Wear a grounding device and observe electrostatic discharge precautions when installing the SIC. Failure to observe this caution could result in damage, or failure of the SIC(s). Caution The power outlet must be located near the equipment and must be easy to access. Continued on next page 24-Hour Technical Support: International:

9 Caution and warning notices, continued Caution Read the installation instructions before connecting the chassis to a power source. Failure to observe this caution could result in poor performance or damage to the equipment. Caution Only trained and qualified personnel should install or performance maintenance on the ION219-A chassis. Failure to observe this caution could result in poor performance or damage to the equipment. WARNING DO NOT connect the power supply module to external power before installing it into the chassis. Failure to observe this warning could result in an electrical shock or death. WARNING Select mounting bracket locations on the chassis that will keep the chassis balanced when mounted in the rack. Failure to observe this warning could allow the chassis to fall, resulting in equipment damage and/or possible injury to persons. WARNING Do not work on the chassis, connect, or disconnect cables during a storm with lightning. Failure to observe this warning could result in an electrical shock or death. 24-Hour Technical Support: International:

10 Section lll Chassis Description In this section These are the topics: Topic See Page Unpacking the chassis 7 ION219-A chassis description 8 24-Hour Technical Support: International:

11 Unpacking the chassis Shipping list Use the following list to verify the contents of the shipping box: Item Part Number 19-slot chassis with AC power supply ION219-A Chassis slot covers IONFP Power Cord Country dependent Rubber feet (Qty 1 = 4 feet) 3456 User Guide Options The following items are optional accessories for the ION219-A chassis: Item AC or DC power supply module Single-slot management module FocalPoint software disk (included with the management module) Dry Contact Relay Part Number IONPS-A IONPS-D IONMM IONDCR 24-Hour Technical Support: International:

12 ION219-A chassis description Chassis The ION219-A 19-Slot Chassis contains a fixed 100Mbs full duplex bus with pointto-point connection with all endpoints, which greatly increases the data bandwidth and response time. Each endpoint in the system (Slide-In Card (SIC), Backplane Controller (BC), power supply (PS) and Agent) has a dedicated port on a 24-Port non-blocking, full-bandwidth 100Mbps Ethernet switch, supporting simultaneous traffic between all endpoints. You can achieve an end-to-end fiber integration solution by paring the modules in a high-density ION chassis with the modules in another ION chassis, or a Transition Networks Point System standalone device. To take full advantage of all the features and functions available with the ION chassis, an ION Management Module (IONMM) is required. The IONMM connects to the chassis backplane and communicates with the individual installed SICs. The IONMM controls the specific features and functions of each SIC. The ION219-A allows the network administrator to connect various copper and fiber-optic network media. The ION219-A chassis provides installation space for up to 19, single-slot SICs. See Figure 1. Figure 1: Front Chassis management methods The ION219-A chassis can be managed and monitored via the IONMM Management Module using the following: An SNMP application such as Transition Networks management software installed at a remote computer A remote Web browser A command-line interface (CLI) at an attached terminal Telnet Continued on next page 24-Hour Technical Support: International:

13 ION219-A chassis description, continued Chassis rear The ION219-A is equipped with an IONPS-A, AC power supply or an optional IONPS-D, DC power supply installed in one of its rear slots. An extra installation space is available for an optional (AC or DC) power supply for redundancy purposes. See Figure 2. Figure 2: Chassis rear view 24-Hour Technical Support: International:

14 Section IV ION219-A chassis installation In this section These are the topics: Topic See Page Installation overview 11 Site requirements 13 Installation Hour Technical Support: International:

15 Installation overview Introduction This section describes the installation and site requirements for installing the ION219-A chassis. Caution Caution Install the ION219-A chassis so that the airflow around it is not restricted. Failure to observe this caution could result in performance problems or damage to the contents of the chassis. Caution Read the installation instructions before connecting the chassis to a power source. Failure to observe this caution could result in poor performance or damage to the chassis and its SICs. Caution Only trained and qualified personnel should install or replace the ION210-A chassis. Failure to observe this caution could result in poor performance or damage to the chassis. Safety considerations The following considerations will help to ensure your safety as well as protection of the chassis and its contents from damage. This list does not contain all the potentially hazardous conditions that could exist at the installation site, so exercise caution at all times. Always unplug all power cords before installing or removing the chassis. Keep the chassis area clear and dust free during and after installation. Keep tools and chassis components away from walk areas. DO NOT place containers containing liquid on top of the chassis. Continued on next page 24-Hour Technical Support: International:

16 Installation overview, continued Lifting safety Even though the ION219-A chassis weights less than twenty (20) pounds, use proper lifting to move the chassis about. Keep your back straight and lift with your legs, not your back. If you need to bend down to lift the chassis, bend at the knees, not at the waist to reduce potential for straining your lower-back muscles. See Figure 3. Figure 3: Unsafe Lifting Techniques Electrical safety Follow these basic guidelines when working with any electrical equipment: Disconnect all power and external cables before installing or removing the chassis. Do not work alone when potential hazard conditions exists. Never assume that power has been disconnect from the circuit always check. Carefully examine your work area for possible hazards such as wet floors, ungrounded power extension cables, and missing safety ground. WARNING Do not work on the chassis, connect, or disconnect cables during a storm with lightning activity. Failure to observe this warning could result in an electrical shock or death. 24-Hour Technical Support: International:

17 Site requirements Site requirements To assure normal operation and avoid unnecessary maintenance, plan the site configuration and prepare the site before installation. After installation, make sure that the site maintains an ambient temperature of 0ºC to 50ºC (32ºF to122ºf). Caution To prevent the chassis from overheating, do not operate it in an area that exceeds the maximum recommended ambient temperature 50ºC (122ºF). AC power The IONPS-A, AC power supply can operate on input voltage and current within the range of 100 to to 60 Hz, rated at 200 watts max output. Caution The power outlet must be located near the equipment and must be easy to access. WARNING If the voltage indication on the label is different from the power outlet voltage, DO NOT plug the chassis into that receptacle. A voltage mismatch can cause equipment damage and may pose a fire hazard. WARNING Take care not to overload the circuit that supplies power to the chassis. Failure to observe this warning could result in a fire. WARNING The chassis must be grounded. Make sure that the host is connected to earth ground during normal use. Failure to observe this warning could result in electrical shocks. Continued on next page 24-Hour Technical Support: International:

18 Site requirements, continued Plant wiring The following guidelines consider the plant wiring and cabling at your site. When planning the location of the chassis, consider the distance limitations of signaling, electromagnetic interference (EMI), and connector capability. When wires are run from any significant distance in an electromagnetic field, interference can occur between the field and the signal on the wires. If wires exceed recommended distances, or if wires pass between buildings, consider the potential for lightening strikes. The electromagnetic pulse (EMP) caused by lighting or other high-energy phenomena can easily couple enough energy into unshielded cable to destroy electronic devices. Site environment The chassis can operate as a standalone system or can be mounted in a rack in a secure wiring closet. It requires a dry, clean, well-ventilated environment. An internal fan system pulls air from the front of the system and exhausts it through the chassis rear. The flow of ambient air must be maintained to ensure proper operation. If the airflow is blocked or restricted, or if the intake air is too warm, an overtemperature condition will occur. To ensure normal operation and avoid unnecessary maintenance, plan your site configuration and prepare your site before installation. After installation, make sure the site maintains an ambient temperature of 0ºC to 50ºC (32ºF to122ºf). Keep the area around the chassis as dust free as possible. Equipment racks Multiple chassis can be rack-mounted with little or no clearance above and below them. However, when mounting the chassis in a rack with other equipment or when placing it on the floor with other equipment located close by, ensure that the exhaust from other equipment does not blow into the intake of the chassis. 24-Hour Technical Support: International:

19 Installation Installing the chassis The ION219-A chassis can be installed in a standard 19-inch rack or on a table, shelf, or other stable surfaces. Tabletop installation The ION219-A chassis comes with nine (9) rubber feet for installation on a table or other flat, stable surface in a well-ventilated area. If tabletop installation is desired, remove the rubber feet from the card and place them on the bottom of the chassis. Distribute the feet so that the chassis is level when placed upright. Rack installation The Maximum Recommended Ambient Temperature (TMRA) for the ION219-A chassis is 50ºC (122ºF). When installing the ION219-A chassis in a closed or multiunit rack assembly, the operating ambient temperature of the rack environment could be greater than room ambient. Note: Reliably grounding is required for rack-mounted equipment. Power supply connections other than direct connections to the branch circuit (e.g., use of power strips) should be employed. WARNING Select mounting bracket locations on the chassis that will keep the chassis balanced when mounted in the rack. Failure to observe this warning could allow the chassis to fall, resulting in equipment damage and/or possible injury to persons. Continued on next page 24-Hour Technical Support: International:

20 Installation, continued Rack mount ears The ION219-A chassis has facilities that allow the installation of the rack mount ears on the chassis, either flush against the front or recessed from the front of the rack as shown in Figure 4. Figure 4: Rack Mount Ear Installation Positions Continued on next page 24-Hour Technical Support: International:

21 Installation, continued Note: Installation rack-mount-ear mounting screws (cover-to-frame screws, see Figure 5) are provided. Rack mount screws and clip nuts are NOT provided. Installing rack mount ears To install the ION219-A chassis rack mount ears, do the following: Step Action 1. Determine the preferred alignment of the chassis into the rack. 2. Using a Phillips screw, remove the six (6) cover-to-frame screws (three on each side of the chassis). See Figure Align the mounting bracket in the selected installation position, as shown in Figure 5. Figure 5: ION219-A Rack Mount Ear Installation 4. Using a Phillips screwdriver, install the three (3) screws to mount the rack mount ear to the side of the chassis. See Figure 5 above. 5. Repeat steps 2 and 4 for the second rack mount ear. Continued on next page 24-Hour Technical Support: International:

22 Installation, continued Rack installation To install the chassis in a rack, do the following: Step Action 1. Locate four (4) mounting screws (not provided) and optional clip-nuts (not provided) for each chassis to be installed. 2. Carefully position and align the chassis to the mounting holes in the rack, as shown in Figure Install two (2) screws through the right bracket into the right mounting rail and two (2) screws through the left bracket into the left mounting rail, using the clip nuts (not provided) to secure the chassis to the rack. Figure 6: Rack Mounting Grounding lugs The ION219-A chassis comes equipped with grounding lugs, which are provided for a grounding conductor wire terminated with a two-hole, compression-type grounding connector. The grounding wire must be a copper conductor (not provided). Continued on next page 24-Hour Technical Support: International:

23 Installation, continued Grounding path The electrical conducting path from the chassis to ground must: Flow via the grounding lugs to the Common Bonding Network (CBN) for telecom installations, or to an alternate approved grounding system (if required) for non-telecom installations. Be sufficiently low in impedance to conduct fault currents likely to be present on the chassis. Enable proper operation of any over-current protection devices. Fasten the two-hole compression-type grounding connector to the grounding lugs with the provided Kepsnut fasteners. See Figure 7. Figure 7: Chassis Grounding Hardware Continued on next page 24-Hour Technical Support: International:

24 Installation, continued Ground installation To ground the ION219-A chassis, do the following: Step Action 1. Obtain one (1) properly terminated, grounding conductor (12 AWG copper wire gauge or larger) with a two-hole, compression-type, grounding connector. Note the manufacturer's applied torque required for the connector. 2. Attach the grounding conductor to the chassis by placing the two-hole, compression-type connector onto the grounding lugs and then fasten with the appropriate lock-washers and lug nuts at the proper torque. See Figure Attach the opposite end of the properly terminated grounding conductor to the Common Bonding Network (CBN) for telecom installations, or to an approved grounding system (if required) for non-telecom installations. Figure 8: Grounding the Chassis 24-Hour Technical Support: International:

25 Section V Chassis Slide-In Cards (SICs) In this section These are the topics Topic See Page Chassis slide-in card (SICs) 22 Management module SIC 23 Installing SICs in chassis 24 Replacing SICs Hour Technical Support: International:

26 Chassis slide-in cards (SIC) (SIC) Transition Networks SICs, installed in slots at the front of the chassis, allow the network administrator to connect various copper and fiber-optic network media over topologies that include Ethernet, Fast Ethernet, DS3/E3, T1-E1 as well as many others. Go to then click on Products/Media Converters/Media Converts by Networking Topology to see the complete list and gain additional information. Note: Refer to the user s guide that comes with each SIC for specific information on the cables, connectors, and LED indicators of the individual SICs. IMPORTANT Slots in the without a SIC installed must have a protective slot cover (IONFP) over them for Class A compliance. Chassis face plate Install a chassis slot cover over any unused chassis slot by aligning the hole in the slot cover with the threaded hole in the chassis. Secure the slot cover with the enclosed screws. See Figure 9. Figure 9: Chassis Slot Cover 24-Hour Technical Support: International:

27 Management module SIC IONMM management module The IONMM Single-Slot Management Module can be installed to enable network management of a single ION chassis. See Figure 10. Note: Refer to the IONMM user s guide, 33457, for more information on the IONMM Single-Slot Management Module. RESET USB Host USB Device PWR 10/100Base-T/TX 10/100Base-T/TX Figure 10: IONMM Management Module Continued on next page 24-Hour Technical Support: International:

28 Installing SICs in chassis CAUTION Wear a grounding device and observe electrostatic discharge precautions when installing the SIC(s) into the chassis. Failure to observe this caution could result in damage or failure of the SIC(s). Note: SICs can be installed in any slot, and in any order in the chassis. Installation To install the SIC into the chassis, do the following: Note: If the SIC requires two slots, remove the protective plates from the adjacent slot as well. Step Action 1. Remove the protective plate from the installation slot by removing the one (1) screw that secures the plate to the front of the chassis. 2. Align the SIC to the chassis slot, as shown Figure 11. Figure 11: SIC Installation 3. Carefully slide the SIC fully into the slot until it seats to the backplane. 4. Push in and rotate the attached panel fastener screw clockwise to secure the SIC to the chassis. 5. Repeat steps 1 thru 4 for additional SICs. 24-Hour Technical Support: International:

29 Replacing SlCs CAUTION Wear a grounding device and observe electrostatic discharge precautions when replacing SICs. Failure to observe this caution could result in damage or failure of the SICs. Note: All SICs are hot swappable. SIC replacement To replace the SIC, do the following: Step Action 1. Loosen the panel fastener securing the SIC to the chassis front. 2. Pull the SIC from the chassis in the direction indicated by the arrow shown in Figure 12. Figure 12: SIC Replacement 3. Align the SIC to the chassis slot. 4. Carefully slide the SIC fully into the slot until it seats to the backplane. 5. Push in and rotate the attached panel fastener screw clockwise to secure the SIC to the chassis. 24-Hour Technical Support: International:

30 Section VI Chassis Power In this section These are the topics Topic See Page Chassis power LEDs 27 Powering the ION219-A chassis 28 Powering the AC power supply module 30 Replacing power supply fuse 31 Replacing the power supply 32 Powering the ION219-D chassis 35 Replacing DC power supply fuse 39 Replacing the DC power supply 40 Optional AC or DC power supply module Hour Technical Support: International:

31 Chassis power LEDs Description The power LEDs are located left side of the chassis front panel. The LEDs indicate power supply ON/Ready state. See Figure 13. Figure 13: Power supply LEDs Power indicator LEDs Power LED indicators present the state of each installed power supply. The LED will light when the respective power supply (PS1 or PS2) is plugged into power with the power ON/OFF switch in the ON position. The number designations associated with the LED on the chassis are as follows: PS1 refers to the power supply installed in the left primary slot when looking at the chassis from the rear. When plugged into power, with the power ON/OFF switch in the ON position, the PS1 LED will be lit. PS2 refers to the power supply installed in the right secondary slot (redundant power supply) when looking at the chassis from the rear. When plugged into power, with the power ON/OFF switch in the ON position, the PS2 LED will be lit. The LED will be lit even if the power supply is not supplying power to the chassis (redundant standby state). 24-Hour Technical Support: International:

32 Powering the ION219-A chassis AC power supply module The ION219-A chassis comes equipped with an IONPS-A, AC power supply module installed in the left bay viewed from the rear of the chassis (optional IONPS-D, DC power supply module). The power supply module delivers power to all SICs in the chassis. Power supply components The components of the AC power supply module include: 1. Fans (two for exhausting warm air from the power supply module) 2. Power LED (on chassis frame front also) 3. ON/OFF switch, when in the ON position power is supplied to the ION chassis 4. Fuse (inline AC) 5. Handle 6. AC power receptacle for an AC power plug 7. Dry Contact Relay (optional) See Figure 14. Figure 14: ION AC Power Supply Module Continued on next page 24-Hour Technical Support: International:

33 Powering the ION219-A chassis, continued Optional Power supply module An extra installation slot is available in the back of the chassis for installing an optional AC or DC power supply module for redundancy purposes. A blank plate covers the slot for the power supply module. See Figure 15. Figure 15: (Rear) 24-Hour Technical Support: International:

34 AC power supply module Power To power the ION219-A chassis, do the following: Step Action 1. Connect the female end of the power cord to the AC power receptacle on the power supply module. 2. Plug the male end of the power cord into the voltage AC rack or wall AC receptacle. 3. Verify that the chassis power ON status by viewing the illuminated power LED on the power supply module, and on the front of the chassis (PS1 power supply 1 and PS2 power supply 2). See Figure 16. Figure 16: Connect AC External Power 24-Hour Technical Support: International:

35 Replacing AC power supply fuse Warning DO NOT attempt to replace the fuse without pressing the power ON/OFF switch to the OFF position and removing the power cord. Failure to observe this warning could result in an electrical shock or death. AC fuse replacement To replace the AC fuse, do the following: Step Action 1. Turn the power supply switch to the OFF position. See Figure 17A. 2. Disconnect the power cord from the AC wall outlet and from the AC power receptacle of the power supply module. See Figure 17A. 3. Place a small flathead screwdriver or similar tool as shown in Figure 17A and then pull forward to extract the fuse holder. See Figure 17B. 4. Remove the fuse from the fuse holder, as shown in Figure 17B. 5. Replace the fuse with an equivalent amperage and voltage rated fuse. 6. Insert the fuse holder back into the power supply module. 7. Insert the AC power cord back into the AC power receptacle on the chassis and then in the AC wall receptacle, (fans are operating). 8. Press the power supply switch to the ON position. (A) (B) Figure 17A/B: Fuse Replacement 24-Hour Technical Support: International:

36 Replacing the power supply module Warning DO NOT connect the power supply module to the external power before installing it into the chassis. Failure to observe this warning could result in equipment damage or electrical shock. Power supply replacement To replace the power supply module, do the following: Step Action 1. Press the POWER SWITCH to OFF position. See Figure 18A. 2. Remove the AC power cord from the AC wall outlet. 3. Remove the other end of the AC power cord from the power supply module. 4. Remove the chassis ground (if necessary). See Figure 18B. (A) (B) Figure 18A/B: Power Supply Module Replacement Continued on next page 24-Hour Technical Support: International:

37 Replacing the power supply module, continued Step Action 5. Remove the two (2) screws securing the power supply module to the chassis. Retain the screws for installing the replacement power-supply module. See Figure Pull the power supply module from the chassis and place it on a stable surface. Figure 19: Removing Power Supply Module from Chassis Continued on next page 24-Hour Technical Support: International:

38 Replacing the power supply module, continued Step Action 7. Push the ON/OFF switch to the OFF position on the replacement power supply module. 8. Carefully position the power supply module at the chassis slot, as shown in Figure 20. Figure 20: Positioning the Power Supply Module at Chassis Slot 9. Slide the replacement power-supply module fully until it seats to the backplane of the chassis. 10. Insert the two (2) retained mounting screws through the power supply module into the chassis and tighten them. See Figure Replace the grounding hardware on the chassis if necessary. 12. Insert the power cord into the power receptacle on the power supply module. 13. Plug the other end of the power cord into AC wall receptacle. 14. Push the power supply ON/OFF switch to the ON position. 15. The power ON LED will turn ON and the fans will be operational, indicating the power supply module is in operation. 24-Hour Technical Support: International:

39 Powering the ION219-D chassis AC power supply module The ION219-D chassis comes equipped with an IONPS-D, DC power supply module installed in the left bay viewed from the rear of the chassis (optional IONPS-A, AC power supply module). The power supply module delivers power to all SICs in the chassis. Power supply components The components of the DC power supply module include: 1. Fan 2. Ground Screw 3. Handle 4. Power ON LED 5. 2-Position Euro Block 6. Dry Contact Relay Optional 7. Temperature Sensor See Figure 21. Figure 21: Power Module Components Continued on next page 24-Hour Technical Support: International:

40 Powering the ION219-D chassis, continued Notices The IONPS-D power module must be installed by qualified technical personnel only. Transition Networks assumes no responsibility for the improper installation, set up or use of these power module. The information in this user s guide is subject to change. For the most up-to-date information, see the user s guide on-line at Important All installation and service must be performed by qualified personnel only. Read and follow all CAUTION and WARNING notices, instructions marked on the product, including this manual. The IONPS-D DC power module is intended for installation in restricted access location only. The IONPS-D, DC power module can replace an existing DC power module or an AC power module in an ION Chassis. Caution While installing or servicing the power module, wear a grounding device and observe all electrostatic discharge precautions. Failure to observe this caution could result in damage to, or failure of the power module. Power source circuit requirements The IONPS-D power module must be connected to a Safety Extra Low Voltage (SELV) circuit. The installer must first determine the circuit s characteristics (limited current, and hazardous energy levels, etc.) and then install the power module reliably, routing and securing the DC input wires safely in accordance with local and national electrical codes. Equipment grounding WARNING The power module has a provision for grounding. Equipment grounding is vital to ensure safe operation. The installer must ensure that the power module is properly grounded during and after installation. Failure to observe this warning could result in an electric shock. Continued on next page 24-Hour Technical Support: International:

41 Powering the ION219-D chassis, continued Disconnect requirements WARNING A readily accessible, suitable National Electrical Code (NEC) or local electrical code approved disconnect device and branch-circuit protector must be part of the building's installed wiring to accommodate permanently connected equipment. The approved disconnect device and branch-circuit protector must be suitable for the rated voltage and current specified. Failure to observe this warning could result in an electric shock, even death. Ensure that the disconnect device for the external power source is OPEN (turned OFF) before disconnecting or connecting the power leads to the power module. Failure to observe this warning could result in an electric shock, even death. While installing or servicing the power module, wear a grounding device and observe all electrostatic discharge precautions. Failure to observe this caution could result in damage to, or failure of the power module. Connecting external power WARNING Do not connect the power module to an external power source before installing it into the chassis. Failure to observe this warning could result in an electrical shock, even death. DC power To connect power to the DC power module in the ION chassis, do the following: Step Action 1. Turn main power source OFF. 2. Loosen the 2 mounting screws, attaching the Euro Block to the power module and pull it from the power module. See Figure 22. Ground Screw Power Supply 2-Position Euro Block Mounting Screws Figure 22: Removing EURO Block from DC Power Supply Continued on next page 24-Hour Technical Support: International:

42 Powering the ION219-D chassis, continued Step Action 3. Noting polarity insert the 2 power wires into the EURO block. See Figure Use the 2 wire-securing screws to secure the power wires in the Euro Block. See Figure 23. Euro Block Wire Securing Screws Wire Slots Power Wires Mounting Screws Qty (2) Connect to main power source Figure 23: Installing Power Wires 5. Connect the other end of the power wires to the main power source. 6. Reinsert the Euro Block into the power module and secure it using the 2, Euro Block mounting screws, shown in Figure 23. WARNING Equipment grounding is vital to ensure safe operation. The installer must ensure that the power module is properly grounded during and after installation. Failure to observe this warning could result in an electric shock. 7. Turn the main power ON: the power LED on the power module should be ON and the fan will be rotating. 24-Hour Technical Support: International:

43 Replacing DC power supply fuse Warning Ensure that the IONPS-D, DC power module has been disconnected from the external power source. Failure to observe this caution could result in an electrical shock or death Replacing the fuse To replace the fuse in the IONPS-D, DC power module, do the following: Step Action 1. Ensure the main power source is switched OFF. 2. Remove the power module from the chassis to expose the fuse. See Figure Carefully pull the fuse from the fuse holder. See Figure 24. Figure 24: Fuse Holder with Fuse 4. Replace the fuse with an equivalent amperage and voltage rated fuse. 5. Insert and secure the power module to the chassis. 6. Switch the main power source to ON: the fan should be operational and the power LED will be lit. 24-Hour Technical Support: International:

44 Replacing the DC power supply Warning DO NOT connect the power supply module to the external power before installing it into the chassis. Failure to observe this warning could result in equipment damage or electrical shock. Note: The power module can be hot swapped (i.e., swapped while the chassis is in operation) provided that it is not connected to an active (switched ON) external power source. Power supply replacement To replace the power supply module, do the following: Step Action 1. Switch the main DC power source OFF 2. Remove the chassis ground lug if necessary. 3. Remove the 2 screws holding EURO block containing the power wires. 4. Remove and keep the two (2) 6-32 philips head screws, securing the power module to the chassis. 5. Carefully pull the power module from the chassis. 6. Locate the new power module. 7. Install the Euro Block containing the power wires. Continued on next page 24-Hour Technical Support: International:

45 Replacing the DC power supply, continued Step Action 8. Position the power module at the chassis slot, as shown in Figure 25. Figure 25: Replacing the DC Power Supply 9. Slide the power module completely into the chassis slot. 10. Insert the two screws to attach the power module to the chassis. 11. If necessary, attach the chassis grounding log. 12. Switch the main power source to the ON position. The fan will be operations and the power LED will be lit. 24-Hour Technical Support: International:

46 Optional AC or DC power supply module Dual power supplies Alternatively, you can install a second AC or DC power supply module in the same chassis (power redundancy). Figure 26 shows two installed AC power supply modules. Figure 26: Rear 2 AC Power Supply Modules Installing Power supply To install the optional power supply module, do the following: Step Action 1. Remove the grounding hardware if necessary. 2. Remove the mounting screws from the blank plate and keep the two mounting screws, shown in Figure Remove the blank plate and keep it for future use. See Figure 27. Figure 27: Remove Blank Plate Slot Cover Continued on next page 24-Hour Technical Support: International:

47 Optional AC or DC power supply module, continued Installing Power supply (continued) Warnings DO NOT insert the power cord into an AC power receptacle before installing the power supply module into the chassis. Failure to observe this warning could result in an electrical shock. Step Action 4. Make sure that the AC power cord IS NOT plugged into external AC power source. 5. Position the power supply module as shown in Figure 28. Figure 28: Power Supply Module Installation (Secondary Slot) Continued on next page 24-Hour Technical Support: International:

48 Optional AC or DC power supply module, continued Installing power supply module (continued) Step Action 6. Slide the power supply module fully into the chassis until it seats to the backplane Note: Upon insertion, the fans on the secondary power-supply module will be operation. The fans will operate regardless the position of the ON/OFF switch. Since the secondary power module is used for redundancy, it receives power from the chassis backplane to operate its fans, which is supplied by the primary power supply module. When the primary power-supply module becomes non-operational, the secondary power supply module powers the chassis. When a power supply module is inserted into the primary slot and becomes operational, the secondary power supply module resumes its previous redundancy state. There is no power sharing or power balancing. 7. Insert and tighten the two mounting screws. See Figure Insert the power cord into the power receptacle on the power supply module. 9. Plug the other end of the power cord into an external AC power source. 10. Press the power switch to the ON position. 24-Hour Technical Support: International:

49 Section VII Network Connectivity In this section These are the topics: Topic See Page Connecting chassis module to the network 46 Network management Hour Technical Support: International:

50 Connecting chassis SICs to the network CAUTION Connect input/output network cables ONLY to SICs within the same network protocol (such as Ethernet-to-Ethernet, Fast Ethernet-to-Fast Ethernet, ATM-to- ATM). Failure to observe this caution will cause data transfers to fail. SICs to network connections Once the ION219-A chassis has been installed, the SICs can be connected to the network. Refer to user s guides included with the SICs for cabling specifications and instructions. Chassis daily operation Daily operation of the ION219-A chassis requires no network administrator activity except for the occasional monitoring of the status LED indicators on the chassis and on the installed SICs. SIC monitoring The IONMM and each SIC have one or more LED indicators to help monitor the ION219-A chassis in the network. Refer to the user s guide included with the IONMM and each SIC to interpret the LED indicators. 24-Hour Technical Support: International:

51 Network management Firmware and FocalPoint applications The ION219-A firmware in the IONMM is described in the IONMM user s guides. These manual are available on-line at The ION219-A firmware is embedded in the management module. The firmware allows the network administrator to configure and manage the SICs in the ION219-A chassis from an attached terminal or from a remote, networked computer. The firmware includes the Transition Networks Command Line Interface (CLI), a telnet server, a Web browser, and an SNMP (Simple Network Management Protocol) agent. In addition, Transition Networks FocalPoint application installs in the networked computer to provide a Graphical User Interface (GUI) to monitor the ION219Achassis. 24-Hour Technical Support: International:

52 Section VIII Troubleshooting Problem corrective action table Introduction This section provides basic troubleshooting information for the ION219-A chassis via a problem and cause table. The problems are stated in the problem column and the potential cause is listed in the cause column. If the problem cannot be remedied, based on the information below, contact our 24-Hour Technical Support department at , International: Problem No power ON state Cause 1. Is the power supply inserted fully into the chassis? 2. Is the power supply power cord fully plugged into an AC power receptacle? If powered by DC: Check power wire into EURO block. 3. Does the external AC or DC power source provide power? 4. Is the Power LED on Power Module illuminated? 5. Is the fuse on the power supply module blown? If yes, see the Replacing the power supply fuse section in this manual. 6. Contact Technical Support: US/Canada: International: Hour Technical Support: International:

53 Section IX Customer Information In this section These are the topics: Topic See Page Contact us 50 Declaration of conformity 51 Warranty 52 Compliance information Hour Technical Support: International:

54 Contact us Technical support Technical Support is available 24 hours a day. United States: International: Live web chat Chat live via the Web with a Transition Networks Technical Support Specialist. Go to and then click the Transition Now link and follow the instructions. Web-based training Transition Networks provides 12 to 16 web-based seminars per month. Login at and click the Learning Center/seminars to view offerings and to register. Ask a question anytime by sending an message to our technical support staff: techsupport@transition.com Contacts TRANSITION NETWORKS Red Circle Drive Minnetonka, MN 55343, U.S.A. Telephone: Toll free U.S.A & Canada: Fax: Hour Technical Support: International:

55 Declaration of conformity Declaration of Conformity Name of Mfg: Transitions Networks Red Circle Drive, Minnetonka MN U.S.A. Model: Purpose: To declare that the to which this declaration refers are in compliance with the following directive(s) and standard(s): EMC Directive 2004/108/EC; EN 55022:2006+A1:2007 Class A; EN55024:1998+A1:2001+A2:2003; EN ; EN ; CFR Title 47 Part 15 Subpart B Class A; Low Voltage Directive: 2006/95/EC; IEC :2005(UL) I, the undersigned, hereby declare that the equipment specified above conforms to the above standard(s) Stephen Anderson, Vice President of Engineering August, 2010 Date 24-Hour Technical Support: International:

56 Warranty Limited lifetime warranty Effective for products shipped May 1, 1999 and after. Every Transition Networks labeled product purchased after May 1, 1999 will be free from defects in material and workmanship for the lifetime of the product. This warranty covers the original buyer only and is not transferable. What the warranty does not cover This warranty does not cover equipment damage from accident, acts of God, neglect, contamination, misuse, or abnormal conditions of operation or handling, including over-voltage failures caused by use outside the specified rating of the product, or normal wear and tear of its components. If the customer is unsure of the proper way to install or use the equipment, contact Transition Networks' free technical support services: US/Canada: , International: Repair, replace or refund Transition Networks will at its option: Repair the defective product to functional specifications at no charge Replace the product with an equivalent functional product Refund the purchase price of a defective product Who to contact for returns To return a defective product for warranty coverage, contact the technical support department at Transition Networks for a return authorization number. Reach the technical support department via the following ways: Technical Support is available 24 hours a day: Tel: x200 or Fax: Live web chat: Transition Now 6:30AM to 5:30PM CST Voic , x579 or , x579 Continued on next page 24-Hour Technical Support: International:

57 Warranty, continued How and where to send the returns Send the defective product postage and insurance prepaid to the following address: CSI Material Management Center c/o Transition Networks 6103 Blue Circle Drive Minnetonka, MN 55343, U.S.A. Attn: RETURNS DEPT: Credit Return Authorization (CRA)# or Return Material Authorization (RMA) # Failure to protect the product during shipping may void the warranty. Write the return authorization number on the outside of the carton to ensure its acceptance. We cannot accept delivery of any equipment without a CRA or RMA number. Customer pays non-compliant return costs The customer must pay the non-compliant product(s) return transportation cost to Transition Networks for evaluation of said product(s) for repair or replacement. Transition Networks will pay for shipping the repaired or replaced in-warranty product(s) back to the customer (any or all customs charges, tariffs, and taxes are the responsibility of the customer). Non-warranty repair costs Before making any non-warranty repair, Transition Networks requires a $200 payment, plus shipping costs from and to the customer. If the repair is greater than $200, the customer will receive an estimate of the cost of repair to authorize before Transition Networks makes the repair. If Transition Networks does not receive an authorization, or the product is not repairable, Transition Networks will retain the $200 service charge and return the non-repaired product to the customer. Repaired nonwarranty products Transition Networks fee-based repaired non-warranted products will carry a 180- day limited warranty. All warranty claims are subject to the restrictions and conventions set forth by this document. If after testing, the equipment is classified as "No Problem Found," Transition Networks reserves the right to charge fees for all testing and shipping costs. This warranty is your only remedy This warranty is your only remedy. No other warranties, such as fitness for a particular purpose are expressed or implied. Transition Networks is not liable for any special, indirect, incidental or consequential damages or losses, including loss of data, arising from any cause or theory. Authorized resellers ARE NOT authorized to extend any different warranty on behalf of transition networks. 24-Hour Technical Support: International:

58 Compliance information Standards CE Mark FCC Regulations This equipment complies with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the customer will be required to correct the interference at the customer s own cost. Canadian Regulations This digital device does not exceed the Class A limits for radio noise from digital devices established by the radio interference regulations of the Canadian Department of Communications. Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la Class A prescrites dans le Règlement sur le brouillage radioélectrique édicté par le ministère des Communications du Canada. European Regulations CAUTION This is a Class A product. In a domestic environment, this product could cause radio interference in which case the user may be required to take adequate measures. Achtung! Dieses ist ein Gerät der Funkstörgrenzwertklasse A. In Wohnbereichen können bei Betrieb dieses Gerätes Rundfunkstörungen auftreten. In diesem Fäll ist der Benutzer für Gegenmaßnahmen verantwortlich. Attention! Ceci est un produit de Classe A. Dans un environnent domestique, ce produit risque de créer des interférences radioélectriques, il appartiendra alors à l'utilsateur de prende les mesures spécifiques appropriées. Continued on next page 24-Hour Technical Support: International:

59 Compliance information, continued European Regulations (continued) In accordance with European Union Directive 2002/96/EC of the European Parliament and of the Council of 27 January 2003, Transition Networks will accept post usage returns of this product for proper disposal. The contact information for this activity can be found in the 'Contact Us' portion of this document. CAUTION: RJ connectors are NOT INTENDED FOR CONNECTION TO THE PUBLIC TELEPHONE NETWORK. Failure to observe this caution could result in damage to the public telephone network. Der Anschluss dieses Gerätes an ein öffentlickes Telekommunikationsnetz in den EG-Mitgliedstaaten verstösst gegen die jeweligen einzelstaatlichen Gesetze zur Anwendung der Richtlinie 91/263/EWG zur Angleichung der Rechtsvorschriften der Mitgliedstaaten über Telekommunikationsendeinrichtungen einschliesslich der gegenseitigen Anerkennung ihrer Konformität. 24-Hour Technical Support: International: