GRX-PRG Programming Control Interface

Transcription

1 grx-prg-.9.0 Programming Control Interface Description Integrates a GAFIK Eye Lighting Control System with a PC or other digital equipment that supports S communication. Provides a basic S command set that allows a PC to monitor and control lighting. Built-in Astronomic Timeclock provides ability to schedule lighting events. Example: lobby lights turn on to scene at 7:0 a.m. or 0 minutes after sunrise. Enables use of a PC to set up GX-00 and GX-00 Control Units. Comes with easy-to-use, point-and-click Windows compatible LIAISONTM software for scheduling the Astronomic Timeclock and using the Programmer Interface. Functionality is selected using DIP switches. Operates with or without a PC connected. May be programmed to control any combination of one to eight GAFIK Eye 000 or 000 Series Control Units. GX-00 and GX-00 Control Units may utilize the Astronomic Timeclock function of the. GX-00 and GX-00 Control Units may utilize all functions of the. Windows is a registered trademark of Microsoft Corporation.

2 Specifications grx-prg-.9.0 Power Low-voltage Class (PELV) Operating Voltage: / V Direct Current. Basic S Command Set Monitoring: Scene selection and scene status updates. Control: Scene selection, scene lockout, sequencing, zone lockout, zone raise/lower. Astronomic Timeclock Allows lighting changes to occur automatically based on time of day and/or day of week/month, as well as relative to sunrise and sunset. Supports four schedules with 60 lighting events per schedule and one Super Sequence. Allows user to start, pause, and stop schedules from a PC, a Wallstation, or by a DIP switch on the Interface. Provides commands to set and monitor the Timeclock s time, date, and day of week, and report sunrise and sunset. Programmer Interface Permits complete set up of the following on GX-00 or GX-00 Control Units via an IBMTM-compatible PC: Scenes, including light levels in % increments and fade times. Load type settings. Tamper-proof protection of scenes. Assignment of communication between Control Units and Wallstations. Dimmer Panel zone and load assignment Allows an IBM-compatible PC to query GX-00 and GX-00 Control Units for their setup, including type of Control Unit and number of zones. LIAISONTM Software Allows use of a PC to create timeclock schedules for all GX-000 and GX-000 Control Units. Allows use of a PC to create setups for GX-00 and GX-00 Control Units. Provides downloading of schedules and setups to Interface and Control Units. Works on any PC operating with Windows. or higher. Supplied by Lutron. Updates are available online at System Communications and Capacity Low-voltage type Class (PELV) wiring connects Interface to Control Units and other components. One Interface per GAFIK Eye 000 or 000 system. Automatically occupies wallstation address 6. 0 feet (m) maximum from Interface to PC or other S source. Environment -0 F (0-0 C). elative humidity less than 90% non-condensing.

3 grx-prg-.9.0 Functions DIP Switch Function When set to ON When set to OFF Zone Lock etain If power goes out, locked zones stay locked when power returns. Power cycling unlocks locked zones. Scene Lock etain If power goes out, locked scenes stay locked when power returns. Power cycling unlocks locked scenes. Sequence etain If power goes out, sequencing resumes when power returns. Power cycling stops sequencing. Sequencing Scene ange Sequencing loops through scenes to 6. Sequencing loops through scenes to. Not Used 6 Button Feedback Interface reports Control Unit and Wallstation button presses. No reporting on button presses. 7 Scene Status Interface reports scene changes. No reporting on scene changes. 8 Astronomic Timeclock Schedules Enables internal Timeclock. Disables internal Timeclock.

4 Dimensions Front Side grx-prg-.9.0 COOPESBUG, PA 806 POGAMMING INTEF ACE AUXILIA Y CONTOL For use with Lutron GAFIK Eye 00 and 00 products only. PELV (CLASS :USA) SWITCH FUNCTION DESCIPTION ZONE LOCK ETAIN SCENE LOCK ETAIN SEQUENCE ETAIN SEQUENCE TYPE ZONE LOCKED UNITS WILL EMAIN IN ZONE LOCK AFTE A POWE OUT AGE SCENE LOCKED UNITS WILL EMAIN IN SCENE LOCK AFTE A POWE OUT AGE SEQUENCING UNITS WILL AGAIN SEQUENCE AFTE A POWE OUT AGE ON: SEQUENCE SCENES -6 OFF: SEQUENCE SCENES - NOT USED AW FEEDBACK SCENE ST ATUS TIMECLOCK ON/OFF INTEF ACE WILL EPO T WHEN A BUTTON HAS BEEN PUSHED O ELEASED ON A GAFIK EYE MAIN UNIT O ACCESSOY INTEF ACE WILL ETUN THE CUENT SCENE OF ALL MAIN UNITS WHEN A NEW SCENE IS SELECTED WILL ENABLE INTENAL TIMECLOCK 7 / (97mm) GAFIK Eye 000 Series PC O A/V EQUIPMENT DIP Switches Neutral HOT/LIVE SSA Zone Zone Zone CU WIE ONL Y Class TxD xd Ground Screw Link to GAFIK Eye Control Units and Wallstations FO WIING OF 000 SEIES, EFE TO INST ALLATION INSTUCTIONS LED LED V TO GAFIK EYE POWE INPUTS: (+V): (+V): S LINK TO PC O A/V EQUIPMENT (000 SEIES) (000 SEIES) IN OUT S LINK TX Data LED (LED ) S Link (to PC or A/V Equipment Class (PELV) Wiring 6 (7mm) / (8mm) Mounting Mount on a " (0.mm) square junction box. May also mount directly to the wall. Ensure that the metal casing is properly grounded. Connect a ground wire to the ground screw. x Junction Box Wall Wall Insert Wires Through Punch-Outs

5 S Link Wiring grx-prg-.9.0 Use cable provided. Standard 9-pin serial connector plugs into S equipment, other end connects to S Link terminals. Must be 0 feet (m) or less. S Signals S Link Terminal Signal Typical PC or A/V Equipment Pin on 9-pin Cable Common Data In Data Out No Connect No Connect Com TxD xd Low-Voltage Class (PELV) Wiring Make daisy-chain connections to the low-voltage Class (PELV) Link terminals on the front of Interface. Do not use T-taps. un all wires in and out of terminal block. Each terminal accepts up to two #8 AWG (.0mm ) wires. LED lights when the Class (PELV) link is installed correctly. ear View of GAFIK Eye Control Unit (GX-0 shown) NEUTAL HOT/LIVE SSA CU WIE ONLY Lutron Cable GX-CBL-6S 0 ft. (m) Maximum TxD xd PC or AV Equipment ZONE ZONE ZONE GX-S Wiring Terminals Link S Link To additional Wallstations/ (6 Maximum; three from one Control Unit without external VDC power supply)

6 Class (PELV) Terminal Connections grx-prg When used with GX-000 Control Units Two #8 AWG (.0mm ) conductors for common (terminal ) and VDC (terminal ). Ensure that the terminal connection is wired correctly. efer to GX-000 Specification Submittal for more details. One shielded, twisted pair #8 AWG (.0mm ) for data link (terminals and ). When used with GX-000 Control Units Two # AWG (.mm ) conductors for common (terminal ) and VDC (terminal ). These will not fit in terminals. Connect as shown. One shielded, twisted pair #8 AWG (.0mm ) for data link (terminals and ). Connect Drain/Shield as shown. Do not connect to Ground (Earth) or Wallstation/. Connect the bare drain wires and cut off the outside shield. Data Link - () twisted, shielded pair #8 AWG (.0mm ) : : D: Drain/Shield () # AWG (.mm ) () # AWG (.mm ) () #8 AWG (.0mm ) () #8 AWG (.0mm ) Class /PELV Control wiring : Common : VDC LED LED V TO GAFIK EYE TO PC O A/V EQUIPMENT POWE INPUTS: (+V): (000 SEIES) (+V): (000 SEIES) IN OUT S LINK