PAS 300, PROFIBUS Slave Interface Module

Transcription

1 Catalog 08 PROFIBUS-Components 27 PAS 300, PROFIBUS Slave Interface Module PROFIBUS PROFIBUS slave interfaces PROFIBUS slave module The PROFIBUS slave interface module PAS 300 from the Systeme Helmholz GmbH is used to connect digital and analog input/output modules to the PROFIBUS-DP. The module can be fixed to a mounting rack. Up to 12 modules can be connected to the PAS 300 (12 digital or max. 8 analog). The PAS 300 is linked into the hardware configurator of the programming system by a device master file. The PAS 300 interface module performs all communication of the modular I/O device with the master device on the PROFIBUS-DP. The inputs and outputs are assigned to the relevant master by configuration. The PAS 300 module supports all the input/output modules of the Systeme Helmholz GmbH and a wide range of modules of the same design from other manufacturers. PAS 300, PROFIBUS slave interface module Manual PAS 300, german/english AA AA02 Dimensions (LxWxH mm) 116 x 40 x 125 approx. 250 g Power supply Voltage DC 24 V Current consumption max. 625 ma Output voltage DC 5 V Output current at DC 5 V max. 1 A (to backplane) Profibus interface Transmission rate max. 12 MBit/s, autodetection Protocol PROFIBUS DP to EN Addressrange 128 Bytes for inputs 128 Bytes for outputs Module count max. 12 digital, 8 analog Connection male, SUB-D, Permissible ambient temperature - operating 0 C C - transport and storage -25 C C

2 28 PROFIBUS-Components Catalog 08 EasyConnect PROFIBUS-Connector EasyConnect PROFIBUS connector The new EasyConnect PROFIBUS connector from the Systeme Helmholz GmbH rounds off the range of bus connector products excellently. The new EasyConnect connectors feature quick-connect technology, making the stripping of bus conductors superfluous. The bus connectors are used to connect a PROFIBUS node to the PROFIBUS line. The connector is quick to install, and has a metallized housing and integrated terminating resistors. The Systeme Helmholz GmbH offers the new EasyConnect connector with a perpendicular cable outlet. Correct connection of the PROFIBUS cable can quickly be checked visually even after installation. PROFIBUS connector EasyConnect without prog. device connector 90 with prog. device connector BA BB50 The PROFIBUS connectors are also available in boxes containing 10 or 50 pieces. Programming device connector Order No BB50 Order No BA50 yes no Dimensions (LxWxH mm) 72 x 40 x 17 Outgoing cable approx. 40 g vertical outgoing cable suitable for fast-connect stripping tool Terminating resistor Resistor combination integrated and connectable with slide switch Transmission rate max. 12 Mbit/s Interfaces PROFIBUS station SUB-D connector, PROFIBUS cable FC standard cable Current consumption V DC (must come from connected equip.) Current consumption max ma Permissible ambient conditions - operating temperature 0 C C - transport/storage temperatur -25 C C - relative humidity max. 75% at +25 C Degree of protection IP 40

3 Catalog 08 PROFIBUS-Components 29 Bus Connector for PROFIBUS smaller dimension Bus connector for PROFIBUS with (l.) and without (r.) prog. device connector The compact design of the smaller dimensions bus connectors from the Systeme Helmholz GmbH makes them suitable for use with the new CPU types from Siemens. A slide switch sets whether the connector will be used as a node or end of segment. The switch can also be operated when the connector is plugged. The switch setting is clearly visible. The connector must be used as a node ( OFF ) when the incoming bus (A1, B1) and the outgoing bus (A2, B2) are to be interconnected. This deactivates the terminating resistors. The connector must be set as a segment end ( ON ), on the first and last (extreme) stations of the segment. In that case the terminating resistors are connected on the incoming bus, the outgoing bus is disconnected. Bus connector for PROFIBUS without prog. device connector 90 with prog. device connector 90 Stripping tool for PROFIBUS BA BB AA00 The PROFIBUS connectors are also available in boxes containing 10 or 50 pieces. Programming device connector Order No BB12 Order No BA12 yes no Dimensions (LxWxH mm) 64 x 40 x 17 Outgoing cable approx. 40 g vertical outgoing cable suitable for fast-connect stripping tool Terminating resistor Resistor combination integrated and connectable with slide switch Transmission rate max. 12 Mbit/s Interfaces PROFIBUS station SUB-D connector, PROFIBUS cable 4 terminals for wires up to 1.0 mm 2 Current consumption V DC (must come from connected equip.) Current consumption max ma Permissible ambient conditions - operating temperature 0 C C - transport/storage temperature -25 C C - relative humidity max. 75% at +25 C Degree of protection IP 40

4 30 PROFIBUS-Components Bus Connectors Angled and Axial for PROFIBUS Catalog 08 Bus connector 35 for PROFIBUS Axial bus connectors for PROFIBUS The axial and 35 bus connector for PROFIBUS is a further component in our range of connectors providing you with low-cost, compatible alternatives for your automation. The bus connectors are used to connect a PROFIBUS node to the PROFIBUS cable. The connector is quickly mounted and features integrated terminating resistors. The Systeme Helmholz GmbH offers the bus connector with an axial cable and 35 outlet and for transmission rates up to 12 Mbaud. Bus connector for PROFIBUS axial cable outlet 35 cable outlet, without prog. device connector 35 cable outlet, with prog. device connector CA BA BB41 The PROFIBUS connectors are also available in boxes containing 10 or 50 pieces. Dimensions 35, (LxBxH mm) 54 x 40 x 17 Dimensions axial, (LxBxH mm) 68 x 39,5 x 17 Outgoing cable, 35 angled outgoing cable Outgoing cable axial axial outgoing cable, suitable for fastconnect stripping tool Terminating resistor Resistor combination integrated and connectable with slide switch Transmission rate max. 12 Mbit/s Interfaces PROFIBUS station SUB-D connector, PROFIBUS cable 4 terminals for wires up to 1.0 mm² Current consumption DC V (must come from connected equip.) Permissible ambient conditions - operating temperature 0 C C - transport/storage temperature -25 C C - relative humidity max. 75% at +25 C Degree of protection IP 40

5 Catalog 08 PROFIBUS-Components 31 Bus Connector for PROFIBUS Bus connector for PROFIBUS with (l.) and without (r.) prog. device connector The bus connectors for PROFIBUS are a further building block to our assortment that offers you low-cost, compatible alternatives for your automation. The bus connectors are used to connect a PROFIBUS station to the PROFIBUS cable. The connector is quickly mounted and has integrated, connectable terminating resistors. The Systeme Helmholz GmbH offers the bus connector with a vertical outgoing cable, and for transmission rates up to 12 Mbaud. The bus connector is plugged directly onto the PROFIBUS interface (SUB-D connector, ) of the PROFIBUS stations. The PROFIBUS cables are connected using 4-way screw terminals. The cable can be prepared for connection using the fast-connect stripping tool from Siemens. Using a slide switch, you can set whether the connector is to be used as a node or segment end. The switch can also be operated when the connector is installed. The setting can be clearly seen. The connector must be operated in node setting ( OFF ) when the incoming bus (A1, B1) and the outgoing bus (A2, B2) are to be interconnected. The terminating resistors are then bypassed. The connector must be set as a segment end ( ON ), on the first and last (extreme) stations of the segment. In that case the terminating resistors are connected on the incoming bus, the outgoing bus is disconnected. The PROFIBUS connectors are available with a design for use in potentially explosive hazardous zone 2 ("Atex"). Bus connector for PROFIBUS without prog. device connector, Ex-Zone 2 with prog. device connector, Ex-Zone 2 without prog. device connector with spring connection technique with prog. device connector with spring connection technique Stripping tool for PROFIBUS BA BB BA BB AA00 Programming device connector Order No BB11 Order No BA11 yes no Dimensions (LxWxH mm) 65 x 48 x 16 Outgoing cable approx. 40 g vertical outgoing cable suitable for fast-connect stripping tool Terminating resistor Resistor combination integrated and connectable with slide switch Transmission rate max. 12 Mbit/s Interfaces PROFIBUS station SUB-D connector, PROFIBUS cable 4 terminals for wires up to 1,0 mm 2 Current consumption DC V (must come from connected equip.) Current consumption max ma Permissible ambient conditions - operating temperature 0 C C - transport/storage temperature -25 C C - relative humidity max. 75% at +25 C Degree of protection IP 40

6 32 PROFIBUS-Components Catalog 08 Repeater for MPI and PROFIBUS Dropcable PROFIBUS for PG Repeater for MPI and PROFIBUS The RS485 repeater connects two PROFIBUS or MPI bus segments in RS485 technology with max. 32 nodes, including repeaters. With it, transmission rates of 9.6 Kbps to 12 Mbps are possible. The transmission signals are regenerated and retransmitted by the repeater. The repeater can therefore be used to implement long PROFIBUS segments. Active PROFIBUS Dropcable for PG The active profibus dropcable from the Systeme Helmholz GmbH is used for a failure-free connection to an existing PROFIBUS net. The active line is not a radial line because of it`s integrated electronic. Commissioning aids: - Switch for disconnecting segments - Display of bus activity - Disconnection of a segment if terminating resistor has been wrongly connected - Terminating resistor for every segment - Error display on bus - Switch for disconnecting repeater functions Transmission rate 9,6 KBit/s 1000 m 19,2 KBit/s 1000 m 45,45 KBit/s 1000 m 93,75 KBit/s 1000 m 187,5 KBit/s 1000 m 500 KBit/s 400 m 1500 KBit/s 200 m 3000 KBit/s 100 m 6000 KBit/s 100 m KBit/s 100 m MPI-/PROFIBUS-Repeater Dropcable PROFIBUS for PG, 3 m max. Segment length AA BD00 Dimensions (LxWxH mm) 115 x 110 x 35 approx. 240 g Power supply Voltage DC 24 V Current consumption max. 120 ma at 24 V Segment connection 4x 2 terminal block Interface PG/OP PROFIBUS interface Transmission rate max. 12 Mbit/s autodetection Protocol PROFIBUS DP to EN Connection connection, SUB-D, Permissible ambient temperature - operating 0 C C - transport and storage -25 C C

7 Catalog 08 PROFIBUS-Components 33 Terminal Block for MPI and PROFIBUS The PROFIBUS segments can be disconnected by a switch. This action connects a terminating resistor combination. 5 V and 24 V is available at both connectors for supplying MPI and PROFIBUS devices (e.g. SSW7 or operator terminals). The MPI/PROFIBUS multiplexer can be mounted directly onto a DIN rail. Terminal block for MPI/PROFIBUS in a metal housing The MPI/PROFIBUS terminal block allows connection of up to two devices to an MPI or PROFIBUS network. Two SUB-D connectors are located in the housing of the MPI/PROFIBUS terminal block. Terminal block for MPI/PROFIBUS, in a metal housing MPV20 Dimensions (LxWxH mm) 115 x 110 x 35 approx. 230 g Power supply Voltage DC 24 V Current consumption max. 200 ma at 24 V PROFIBUS interface Transmission max. 12 Mbit/s Connection 2x female, SUB-D 4x 2 terminal Perm. ambient temperature - operating 0 C C - transport and storage -25 C C The MPI/PROFIBUS multiplexer permits connection of up to 3 devices to one MPI or PROFIBUS network. The MPI/PROFIBUS multiplexer has a 1.2 m long connecting cable that can be plugged directly into the MPI/PROFIBUS socket of the PLC, but also at any position in a MPI or PROFIBUS network. The PG socket is the only socket that has the full MPI pin assignment. That makes it possible to use direct operation on this socket via an MPI adapter ( SSW 7 or PC adapter ) with programming software. Multiplexer for MPI-/PROFIBUS This pin assignment is not relevant for operation of PROFIBUS devices. The MPI/PROFIBUS multiplexer is powered via the connection line to the CPU. If the terminal does not provide 24 V, it is possible to draw the 24 V from an external source. The 24 V connector for this purpose (green connector) is polarized. Terminal block for MPI/PROFIBUS MPV01 Dimensions (LxWxH mm) 105 x 54 x 30 approx. 135 g Power supply Voltage DC 24 V Current consumption max. 200 ma at 24 V PROFIBUS interface Transmission max. 12 Mbit/s Connection 3x female, SUB-D, Perm. ambient temperature - operating 0 C C - transport and storage -25 C C

8 34 PROFIBUS-Components Catalog 08 NETLink lite, Ethernet-Gateway for MPI/PROFIBUS NETLink lite PG/PC Programmable controller 2,5 m cable length Hub TCP / IP Straight RJ45 Application for the NETLink lite NETLink lite PG/PC NETLink lite, Ethernet-Gateway for MPI/PROFIBUS Installed in a SUB-D shell, it contains a complete field bus participant with a 10/100 Mbps Ethernet interface. It is connected directly to the field bus connector of a automation device and connects it to the next switch or hub via a Ethernet cable. The NETLink lite can be used both in an MPI and in a PROFIBUS network. The 24 volt power supply is drawn via the MPI/PROFI- BUS connection. The driver supplied, links the NETLink lite into the programming software. All programming functions are available. The crossover adapter permits direct connection of the NETLink lite to a laptop or PC without a hub or switch. If no S7 functions are needed, the NETLink lite without S7 driver can be used for OPC SCADA applications (OPC-Server see page 37). lite NETLink lite with S7-Switch NETLink lite without S7-Switch Crossover-adapter MPI MPI CROSS Dimensions (LxWxH mm) 65 x 48 x 16 approx. 150 g (incl. cable and connector) Power supply Voltage DC 24 V Current consumption 70 ma Ethernet Connection Standard Connector 2,5 m cable length Application for the NETLink lite Programmable controller Crossover-Adapter 10 Base-T 100 Base-TX RJ45 PLUG Transmission rate autodetection MPI Transmission rate max. 12 MBit/s Data link FDL frames Operating temperature 0 C to 55 C Indicators 2 LEDs, one of them 2- coloured, communication status

9 Catalog 08 PROFIBUS-Components 35 NETLink PRO Hub PG/PC NETLink PRO TCP / IP Straight RJ45 Programmable controller Application for the NETLink PRO Crossover-Adapter PG/PC NETLink PRO The new NETLink PRO from the Systeme Helmholz GmbH is integrated into the housing of an SSW7 MPI adapter. Its 1.2 m long connecting cable is plugged directly into the CPU of the programmable controller. The connection cable is designed as active line and does not affect the MPI or PROFIBUS. The second PG socket allows the connection of an additional device to the CPU of the programmable controller. The new NETLink PRO can also be connected to an external 24 V source as an option. On the control side, the NETLink PRO permits the full transmission rate of 12 Mbps via MPI and PPOFIBUS. The device automatically detects transmission rates of 10 Mbps or 100 Mbps of the TCP network. On the MPI, at least 8 connections and on the PC side at least 4 connections can be made with the NETLink PRO. The new NETLink PRO also features automatic baud rate detection and flexible configuration options such as DHCP and DNS. An Ethernet socket replaces the usual fixed Ethernet cable. This gives more flexibility with the connection. The MPI/PROFIBUS is galvanically isolated from the external DC 24 V power supply as it is from the Ethernet interface. A 3m ethernet-cable is included with the NETLink PRO. NETLink PRO Crossover-adapter PRO MPI CROSS Application for the NETLink PRO Dimensions (LxWxH mm) 105 x 54 x 30 approx. 250 g Power Supply Voltage DC +24 V ±25 % Current consumption max. 150 ma Communication interface Type 10 Base-T/100 Base-TX Connector RJ45 Transmission rate MPI/PROFIBUS Type Programmable controller NETLink PRO 10/100 MBit/s RS485 Transmission rate max. 12 MBit/s Connector SUB-D, with PG interface and terminating resistor Protocols FDL frames Operating temperature 0 C...60 C Indicators 3 LEDs, therefrom 2 two coloured

10 36 PROFIBUS-Components Catalog 08 NETLink USB PC USBinterface USB-connecting cable (included) NETLink-USB Programmable controller Application for NETLink USB NETLink USB The new NETLink USB is a real alternative to the PROFIBUS-PC slot-in card. Its 1.2 m long connecting cable is plugged directly into the CPU of the programmable controller. The connection cable is designed as active line and does not affect the MPI or PROFIBUS. The second PG socket allows the connection of an additional device to the CPU of the programmable controller. With the NETLink USB it is possible to implement a USB interface on the MPI/PROFIBUS for programming or visualization at the full transmission rate of up to 12 Mbps. It is also possible to implement up to 16 connections. The new NETLink USB is supplied by the USB bus but also has an optional DC 24 V supply and automatic baudrate detection. On the USB, protocols Fullspeed (12 Mbps) & Highspeed (480 Mbps) are supported. The MPI/PROFIBUS is galvanically isolated from the external DC 24 V power supply as it is from the USB interface. A 3m highspeed USB-cable is included with the NETLink USB. NETLink USB USB MPI11 Dimensions (LxWxH mm) 105 x 54 x 30 approx. 250 g Power Supply Voltage DC 24 V ±25 % / DC 5 V USB Current consumption max. 150 ma at DC 24 V / max. 500 ma at DC 5 V USB Communication interface Type USB 2.0 Connector USB-A Transmission rate 12 MBit / 480 MBit MPI/PROFIBUS Type RS485 Transmission rate max. 12 MBit/s Connector Protocols SUB-D, with PG interface and terminating resistor FDL frames Operating temperature 0 C...60 C Indicators 3 LEDs, therefrom 2 two coloured