Operating Manual. 3000E NTCIP Translator Card for IQ Central. p/n Rev 3. IQ Connect for 3000E Operating Manual

Transcription

1 Operating Manual 3000E NTCIP Translator Card for IQ Central p/n Rev 3 Page

2 Copyright 2011 Peek Traffic Corporation All rights reserved. Information furnished by Peek Traffic is believed to be accurate and reliable, however Peek does not warranty the accuracy, completeness, or fitness for use of any of the information furnished. No license is granted by implication or otherwise under any intellectual property. Peek reserves the right to alter any of the Company's products or published technical data relating thereto at any time without notice. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or via any electronic or mechanical means for any purpose other than the purchaser s personal use without the expressed, written permission of Peek Traffic Corporation, a Signal Group Company. Peek Traffic Corporation Corporate Way Palmetto, FL U.S.A. Trademarks IQ Connect, IQ Link, and IQ Central are trademarks or registered trademarks of Peek Traffic Corporation in the USA and other countries. Microsoft and Windows are trademarks or registered trademarks of Microsoft Corporation. Other brands and their products are trademarks or registered trademarks of their respective holders. Page 2

3 Introduction to the IQ Connect Translator IQ Connect is a device that allows a proprietary traffic controller to communicate with a central software system using the industry standard NTCIP protocol. IQ Connect comes in a plug-in card format as well as a shelf-mount format. This guide describes the controller mounted card version of IQ Connect, particularly the card for the Peek 3000E traffic controller. The IQ Connect translator card allows the 3000E to be attached to an NTCIP-based central system, such as IQ Central. The card is installed inside the 3000E controller along the right side of the box, with the front port connectors visible in the Port 3 location on the front panel. The card is connected to the controller via a ribbon cable at the rear of the card. The IQ Connect card for the 3000E allows the controller to be connected to the central system over Ethernet, a serial connection, or an external modem connection. Figure 1 IQ Connect card Figure 2 IQ Connect card in a 3000E IQ Connect card installed in the Port 3 slot Page 3

4 Figure 3 Card installed in Comm3 slot behind front faceplate Heartbeat LED Device Comms LED Central Comms LED (or external modem) Initialization LED (Internal, not used) Figure 4 Front panel connectors and LEDs Page 4

5 Installation Instructions These steps describe how to install an IQ Connect translator card into a Peek 3000E traffic controller: 1. Power off the controller. (This procedure should be performed on a test bench or in a test cabinet rather than in the field.) 2. Open the front of the controller. If there is already a comms card in the Port 3 position, we will need to remove it before we can install the IQ Connect card. If not, skip to step 6 below. 3. First, unplug the cable that runs from the existing comms card to the controller s main board. You will need to press outward on the two wings that hold the cable end in place on the main board. 4. Next, locate the two white standoff posts that hold the card in place. Notice that each of the standoff posts has a loop at the end, out of one side of which a small tab protrudes. Press the tab toward the center of the post to release the card. Repeat this step for both posts. Figure 5 Pressing the standoff post from the old card 5. Press the end of the standoff post and pull the card away from the sidewall of the controller. Remove the old comms card from the controller. 6. If you haven t done so already, remove the IQ Connect card from its anti-static packing bag. Page 5

6 7. Position the card in the 3000E Comm3 card position. The card s ports should be positioned at the front panel openings for these connectors. Push the card onto the 2 white mounting posts. Figure 6 Plugging in the IQ Connect ribbon connector 8. Plug the end of the card s ribbon wire cable into the COMM BOARD socket on the 3000E s main board. The plug will only fit into the socket in one orientation. Figure 7 Pressing the connector into the COMM BOARD socket 9. Press the plug down until it clicks into place. Page 6

7 10. With the card installed in the controller and the front panel open, the back edge of the card is pointing straight up. There is an array of four DIP switches located near this edge, right next to the card s reset button. You will need to use these switches to set the Central Port comm settings. Typically, switches 1 and 2 are set to ON for the fastest Baud rate. Switch 3 should be set to OFF for use with a 3000E controller. Switch 4 should be ON if the connection will be over an external dialup modem connected to the Central port, and OFF for any other type of connection to Central. For more details about these comms settings, refer to page With the controller still open, the card presents a set of eight (8) DIP switches on the edge of the card near the side that is toward you, which are used to set the Device ID for this controller. The Device ID you program here must match the intersection or local number programmed into the controller. The ID is the result of adding together the binary values of the whole set of switches. (Sw1 = 1, Sw2 = 2, Sw3 = 4, SW4= 8, and so on.) For more details about the Device ID setting, refer to page Close the front panel of the controller and return power to the controller. Verify that the unit starts up and you see the normal interface screens, as expected. 13. On the controller, set the proper Device ID value. This is done on the Closed Loop Master/ID screen (Main Menu > 3 > 5 > 1). Set the Intersection ID value to the same value as the Device ID you programmed in step On the same 3000E screen, check the Master Type value. Since the IQ Connect card installation means that you will be connecting the controller directly to the central system (i.e. as an isolated local controller ) rather than through a Master controller, make sure the Master Type is set to 0 (None). Set the Master Number to Choose the type of connection to be made to Central. The choice will determine which port on the front of the IQ Connect to plug into, the cable you will need to use, and the values to set on the 3000E Setup comm PORT 3 screen (MM > 3 > 5 > 2 > PGDN to Port 3). On that screen, just be sure that Hardware is set to Normal and the Baud rate is set to Those settings are used for every connection method to Central. 16. The IQ Connector card LEDs should settle down until the only thing displayed is a flashing Heartbeat LED (the top LED). This completes the installation and setup of the IQ Connect card. Page 7

8 Central Port Communications Settings The small DIP switch array on the rear of the IQ Connect card are used to configure how the RJ-45 Central port, located on the front of the device, functions. Figure 8 Central Port Communications Settings The above settings are the defaults when working with any controller other than an LMD 9200, and the controller is connected to the Central system via a direct serial connection. If the Device port is connected to an LMD 9200 (the same firmware is used for 3000E and LMD 9200 IQ Connect boxes), switch 3 must be set to ON. If the central connection is being made by an external dialup modem, switch 4 needs to be moved to the ON position. Switch Purpose 1 Set Central OFF OFF ON ON Port 2 OFF Baud ON Baud OFF Baud ON Baud Rate 3 Used only when the 3000E/LMD9200 firmware is installed in the IQ Connect unit. Defines the baud rate used by the Device port when communicating for one of these two controller types. OFF = 3000E communications to central (115,200 Baud) ON = LMD 9200 communications to central (9600 Baud) 4 Dialup? OFF = Direct RS232 connection. ON = External Modem on Central port Baud Page 8

9 Device ID Settings The Device ID must match the intersection or local number programmed into the controller. The ID is set by adding up the binary values of those DIP pins that are set to ON. Figure 9 Device ID Setting DIP switches For example, if pins 2, 5 and 8 are set ON, this results in a Device ID for this IQ Connect unit of 146 (= ). Figure 10 Setting the Device ID to 146 Note: Setting all of these switches to OFF and then pressing the Reset button (located on the rear of the IQ Connect unit, near the Central Port DIP switches) will reset the unit to factory settings. Page 9

10 Connecting to Central Steps for a Serial Connection 1) Install the card into the controller and ensure that it is talking to the controller as described earlier in this booklet. (The top right heartbeat LED should be flashing. The bottom right LED should be OFF.) 2) Make sure the Central Port settings DIP switch 4 is set to OFF. 3) Connect the central port (the second port from the bottom) to the serial hub or PC serial port using Peek cable (Refer to the table of Cables and Spare Parts on page 16 for details.) You should now be ready to communicate with Central via a serial connection. Steps for a Dialup Connection 1) Install the card into the controller and ensure that it is talking to the controller as described earlier in this booklet. (The top right heartbeat LED on the card should be flashing. The bottom right LED should be OFF.) 2) Set configuration DIP switch 4 to ON (labeled "Dialup" on the back). 3) Connect the central port to the external dialup modem's DB25 or DB9 serial port using Peek cable (25 pin) or (9 pin). (Refer to the table of Cables and Spare Parts on page 16 for details.) Note: If you are using a GDI dialup modem, use Peek cable to connect to the modem. 4) Connect the phone line to the modem. 5) Power up the modem 6) Restart the controller to trigger it to restart the IQ Connect card and initialize the modem. You are now be ready to communicate with Central over a dialup connection. Page 10

11 Steps for an Ethernet Connection 1. Install the card into the controller and ensure that it is talking to the controller as described earlier in this booklet. (The top right heartbeat LED should be flashing. The bottom right LED should be OFF.) 2. Set the IP address: a) The default IP address / port will be port: 200, address: ID, where the ID matches the ID DIP switch settings on the front. To change this you will need to set the network connection settings using the IP Set Utility. b) Connect you local PC or laptop to the card s Local port on (the third port from the bottom) using the local port serial cable (Peek part # ) c) Run IPSet Utility on the laptop or PC connected. d) Select the com port you connected to and set the address to match the device ID set on the DIP switches. e) Click "Get" in the IP section to retrieve the current settings. f) Modify what you need to and click Set. g) Reset the translator using the reset button on the rear of the card. 3. Plug the ethernet cable into the front of the controller, using the top port on the IQ Connect card. You should now be ready to communicate with Central over an Ethernet connection. Ethernet Notes 1) The IP port shown in IPSet Utility represents the port used for TCP/IP connections. The UDP port is always = TCP port If you plan to use UDP/IP, set the TCP port to 100 less than the UDP port you wish to use in IQ Central. 2) For isolated controllers over Ethernet, set these values in IQ Central: Device Master Address = 0 Device Drop Address = 0 Connection Multidrop Mode = OFF 3) For Ethernet connected masters and locals over Ethernet, set these values in IQ Central: Device Master Address = Master # Device Drop Address = Local Number or 0 for the master itself. Connection Multidrop Mode = ON Page 11

12 Specifications Product...IQ Connect Card for 3000E Part Power Requirements VDC Power Usage...2W Temperature Range to +155 F 34 to +74 C Communications Ethernet...100BaseT, Full Duplex, Auto-detecting (will work with either standard or null modem cables) Local Port...RS-232, 9600 Baud Central Port...RS-232, Set to one of: 1200, 9600, 19200, or baud Set using Rear DIP switches 1 and 2 Device Port...Baud rate is variable from 1200 to baud, based on loaded firmware and Rear DIP switch 3. Box Dimensions Height (5.52 cm) Width (10.3 cm) Depth (18.3 cm) Ribbon Cable...8 Processor CPU...Rabbit 3000 Clock Speed...11 MHz Page 12

13 Figure 11 IQ Connect Card Components Page 13

14 Troubleshooting Symptom Possible Cause Solution Power will not come up on IQ Connect unit (All LEDs are dark) Blown fuse Faulty IQ Connect unit Open the IQ Connect box and replace the fuse (See the Spare Parts list for fuse details) Contact Peek Traffic to arrange to ship IQ Connect unit to the factory Initialization LED stays on indefinitely and the Device Comms LED blinks occasionally (about once a minute) Unit Heartbeat LED blinks but cannot establish a connection between IQ Central and the controller (using an RS232 connection) Faulty communications between IQ Connect and the controller Faulty Port settings in the controller Cable plugged into wrong IQ Connect port Incorrect Intersection or Master ID settings in IQ Central Faulty IQ Central settings for the controller Incorrect Central Port DIP switch settings on the IQ Connect If using an external modem attached to IQ Connect (via CENTRAL port), incorrect Central Port DIP switch settings are set Unit s Device ID does not match the controller s Intersection ID setting. (In the controller, the Master ID must be 1, and the Intersection ID must be the same as the Device ID that is set on the IQ Connect Device ID DIP switches) Refer to the Tech Note: IQ Central Comms Configuration for the proper parameter settings for the various types of controllers and masters Verify that the central cable is plugged into the Central Port on the unit, NOT the Ethernet Port Refer to the Tech Note: IQ Central Comms Configuration for the proper parameter settings Make sure the IQ Central settings for this controller are set properly. See the Tech Note. Make sure red DIP switches 1 through 4 within the IQ Connect are set to ON Make sure DIP switch 4 is set to ON, and DIP switches 1 and 2 are set to the baud rate needed by your modem. IQ Connect Heartbeat LED blinks but cannot establish a connection between IQ Central and the controller (using an Ethernet connection) Cable plugged into wrong IQ Connect port Incorrect Drop or Master Address settings in IQ Central Incorrect Ethernet communications settings for the controller in IQ Central Verify that the central cable is plugged into the Ethernet Port on the unit, NOT the Central Port Refer to the Tech Note: IQ Central Comms Configuration for the proper parameter settings Make sure the IQ Central Ethernet settings for this controller are set correctly, matching those values on your network and in the controller Incorrect IP address set in the IQ Connect unit Configuring the Ethernet settings within the IQ Connect requires the use of the IP Set utility, and is beyond the scope of this document. Page 14

15 Related Documents Document Part Number Release Notes: IQ Connect Firmware 3000E/LMD9200/LMD Release Notes: IQ Connect Firmware M3000E Release Notes: IQ Connect Firmware TMM Release Notes: IQ Connect Firmware 3800EL Release Notes: IQ Connect Firmware OSAM Release Notes: IQ Connect Firmware TMP Release Notes: IQ Connect Firmware 1880EL Release Notes: IQ Connect Firmware 820A Release Notes: IQ Connect Firmware Wapiti Tech Note: IQ Central Comms Configuration Peek 3000E Controller Manual 8204C IQ Central Operating Manual IQ Connect (3000E Card) Manual Peek 3000E Firmware Release Notes IQ Central Release Notes Multisonics 820A (OSAM) Controller Manual MN Multisonics OSAM-32 Master Controller Manual MN Transyt 1880EL Controller Manual Tranyst 3800EL Master Controller Manual Traconex TMP390 Controller Manual MN Traconex TMM-500 Master Controller Manual LMD 9200 Controller Manual 62901v201 LMD 9200 Firmware Release Notes Page 15

16 IQ Connect Ordering Information The following table lists the part numbers to use to order a complete IQ Connect unit, including device cable and the correct firmware for the device type. Note that central and modem cables are not included in these assemblies; they must be ordered separately. IQ Connect Assembly for: Part Number Peek 3000E Local, Internal Card Peek 3000E Local, Shelf-mounted Peek M3000E Master, Shelf-mounted Multisonics OSAM-32 Master, Shelf-mounted Multisonics 820A Local, Shelf-mounted Transyt 3800EL Master, Shelf-mounted Transyt 1880EL Local, Shelf-mounted Traconex TMM-500 Master, Shelf-mounted Traconex TMP390 (CJ or J9) Local, Shelf-mounted LMD 9200 or LMD 40 Local, Shelf-mounted Wapiti 170 Local, Shelf-mounted Page 16

17 Cables / Spare Parts Description Part Number FUSE, 1A, 250V, SLO-BLO, IEC, 5x20MM, GLASS 2F IQ Connect to central cable: Ethernet Standard Ethernet cable IQ Connect to central cable: Direct Serial IQ Connect to central cable: External GDI Modem IQ Connect to central cable: External Modem IQ Connect to local PC cable Battery: 3V DC coin battery CR2032 IQ Connect Rabbit Processor Cable (for loading firmware) 2W Page 17

18 Page 18

19 Page 19

20 Technical Support This contact information will connect you with the IQ Connect product support staff at Peek Traffic Corporation. Peek Traffic Technical Support 2906 Corporate Way Palmetto, FL toll free in the U.S.: 1 (800) tel: 1 (941) fax: 1 (941) tech.support@peektraffic.com website: Page 20